Vehicles Break booster and Master cylinder has an issue and the breaks are stiff with a whistle blowing sound when pressed. And causing a low engine oil sign to pop up and stall out when stopped. This happened while pulling out of a parking lot. The problem was confirmed by a Pep Boys Auto Repair Shop in Federal Way, Washington …
Read full complaint
Vehicles Break booster and Master cylinder has an issue and the breaks are stiff with a whistle blowing sound when pressed. And causing a low engine oil sign to pop up and stall out when stopped. This happened while pulling out of a parking lot. The problem was confirmed by a Pep Boys Auto Repair Shop in Federal Way, Washington State. No, insurance has not looked over it, and no I haven't taken it to be inspected by a Ford dealership/manufacturer
NHTSA ODI #11610541
Mileage unknown · Aug 14, 2024
Service Brakes
I noticed when pressing on the brake pedal it was going to the floor vehicle was not slowing or stopping as it should. I heard a squealing and whistle sound then the check engine light came on. I called the dealership, and they said confirmed the brake booster was internally leaking vacuum causing the check engine light to come …
Read full complaint
I noticed when pressing on the brake pedal it was going to the floor vehicle was not slowing or stopping as it should. I heard a squealing and whistle sound then the check engine light came on. I called the dealership, and they said confirmed the brake booster was internally leaking vacuum causing the check engine light to come on. The brake light is on once again and again the dealership contacted for an appointment. I took the liberty contacting Ford for any recalls and was directed to contact NHTSA and report.
NHTSA ODI #11608603
Mileage unknown · Aug 11, 2024
Service Brakes
2013 Ford Edge Limited- The vehicle experienced a loss of brake pressure, resulting in the brake pedal sinking to the floorboard before the vehicle finally came to a complete stop nearly resulting in a collision. Vehicle was taken to Midas and the independent mechanic notified the owner that the brake master cylinder was malfunc…
Read full complaint
2013 Ford Edge Limited- The vehicle experienced a loss of brake pressure, resulting in the brake pedal sinking to the floorboard before the vehicle finally came to a complete stop nearly resulting in a collision. Vehicle was taken to Midas and the independent mechanic notified the owner that the brake master cylinder was malfunctioning and needed to be replaced immediately.
NHTSA ODI #11607804
Mileage unknown · Jul 25, 2024
Service Brakes
I have a 2013 ford edge. When I press on the brake sometimes it goes down smoothly and I hear a hissing noise and then the next time I brake it is stiff, hard as a rock and I can barely get the vehicle to stop. This is dangerous! A major safety issue but for some unknown reason my 2013 is not showing a recall. I heard that the b…
Read full complaint
I have a 2013 ford edge. When I press on the brake sometimes it goes down smoothly and I hear a hissing noise and then the next time I brake it is stiff, hard as a rock and I can barely get the vehicle to stop. This is dangerous! A major safety issue but for some unknown reason my 2013 is not showing a recall. I heard that the brake boosters could be the problem. Also my check engine light came on when the stiff brake started happening. I just bout the suv 2 weeks ago. Ford will not help me as no recall is issued.
NHTSA ODI #11604618
Mileage unknown · Jul 7, 2024
Service Brakes
I was driving home on the freeway from work and there was an accident where traffic had to slow down. As I slowed down by placing my foot on the brakes the tires skid and the ABS light came on as well as the Brake Service light and Service Advance Trac came on. The brakes locked and I avoided an accident by 2 inches. This is haz…
Read full complaint
I was driving home on the freeway from work and there was an accident where traffic had to slow down. As I slowed down by placing my foot on the brakes the tires skid and the ABS light came on as well as the Brake Service light and Service Advance Trac came on. The brakes locked and I avoided an accident by 2 inches. This is hazardous and dangerous.
NHTSA ODI #11599914
Mileage unknown · Jul 5, 2024
Service Brakes
vehicle has stiff pedal all the way floor and abs kick in lower side of pedal only applyied brake to slow down how ever vehicle yang to left because it was braking un evenly faliure to abs kick in, vehicle felt no brake at all. abs causing only to presure left not, some times you have pedal sundenly pedal is out, i do know they …
Read full complaint
vehicle has stiff pedal all the way floor and abs kick in lower side of pedal only applyied brake to slow down how ever vehicle yang to left because it was braking un evenly faliure to abs kick in, vehicle felt no brake at all. abs causing only to presure left not, some times you have pedal sundenly pedal is out, i do know they have extented warranty for the brake, it is rediculas to loos pedal by rondamly driving, ford should warrantied alll ford edge brake problems, this is not acceptable causeing internal mechanical failer. they must recall and walk away from this article. it horrible when you guy not responded for recall, since they have brake problems
NHTSA ODI #11599256
Mileage unknown · Jun 27, 2024
Service Brakes
Brake booster failed. Ran a stop sign. No brakes!
NHTSA ODI #11597297
Mileage unknown · Jun 20, 2024
EngineService Brakes
Backfiring and brakes don’t work.
NHTSA ODI #11595408
Mileage unknown · Jun 19, 2024
Service Brakes
I took my vehicle to Ford for the brake booster that was issued by Ford. Nothing worked. My brakes would literally go soft and almost to the floor while stopping. It was extremely dangerous and scary. I saw a 2016 recall that replaced the ABS module but my car apparently wasn’t tagged to it. Finally had to foot the $1500 bil…
Read full complaint
I took my vehicle to Ford for the brake booster that was issued by Ford. Nothing worked. My brakes would literally go soft and almost to the floor while stopping. It was extremely dangerous and scary. I saw a 2016 recall that replaced the ABS module but my car apparently wasn’t tagged to it. Finally had to foot the $1500 bill to have the ABS module replaced which seemed to have fixed the issue. Thousands have complained of this same issue so I’m not sure why a recent recall hadn’t been issued by Ford.
NHTSA ODI #11595299
Mileage unknown · Jun 5, 2024
Service Brakes
Brakes hard to push and has trouble stopping vehicle brake booster was replaced but still isn’t working
Ford Motor Company (Ford) is recalling certain model year 2012-2014 Ford Edge and Lincoln MKX vehicles manufactured September 2, 2010, to November 30, 2013; 2013-2014 Ford Taurus and Lincoln MKS vehicles manufactured August 25, 2011, to November 30, 2013; and 2013-2014 Ford Flex and Lincoln MKT vehicles manufactured September 12, 2011, to November 30, 2013. In the affected vehicles, the halfshaft retention circlip may not have been properly installed, and as a result, the halfshaft may move outward and disengage from the linkshaft while driving and without prior warning.
Consequence & remedy
Consequence: If the halfshaft and linkshaft become disengaged while driving, power will no longer be transmitted to the wheels, increasing the risk of a vehicle crash. Additionally, if the parking brake is not applied before exiting the vehicle, the vehicle may roll away despite the transmission being placed in 'Park', increasing the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the vehicles to make sure that the halfshaft is properly retained. If it is not, dealers will replace the linkshaft and also replace the halfshaft if it shows evidence of spline damage, free of charge. The recall began on August 4, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S10.
Ford Motor Company (Ford) is recalling certain model year 2012-2013 Edge vehicles manufactured from September 2, 2010, through April 25, 2013, and equipped with 2.0L engines. The fuel line pulse damper metal housing may crack as a result of an improper manufacturing process. A cracked fuel line pulse damper housing may result in a combination of fuel odor, weepage, or a continuous leak while the fuel system is pressurized.
Consequence & remedy
Consequence: A fuel leak in the presence of an ignition source may result in a fire.
Remedy: Ford will notify owners, and dealers will replace the fuel line with one that does not have a damper, free of charge. The safety recall began on February 25, 2014. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 13S13. IMPORTANT: This recall supersedes recall 12V-438. All vehicles that have been remedied under the previous recall need to have the current remedy applied.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Additional source detail variants (3)
Interior Lighting
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
2013 Ford Edge Problems, Complaints & Recalls | Skip That Year
Illustration