IllustrationContinue to experience the soft brake pedal / loss of brakes / pedal to the floor without warning. Warning Collision lights continue to flash off and on. Has been checked by Ford several times and none can figure out the issue.
2013 Ford Edge
Owner reports · Recalls · Investigations
More warning signs than most Edge years
Owner complaints for the 2013 Ford Edge are substantially higher than the model-year median of 724.
About this comparison →How this year compares
Owner complaints by model year
Compare all Edge years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
1470–25K
63025–50K
50950–75K
24575–100K
206100–150K
56150K+
1,793 reports with mileage · 651 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Electrical System. Review the 854 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Service Brakes. Review the 529 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Structure. Review the 300 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
33 crash reports7 fire reports24 injury reports
Service Brakes complaints
529 reportsMy 2013 Ford Edge had 44,882 miles on it. With no warning or lights, car was difficult to stop. Hissing noise when brakes applied. Very scary! Took it to Ford dealership. They charged me $167 to diagnose the problem as power brake booster, and said it would take 3-4 weeks to get the part. Ford knows there’s a problem (N102) and…
Read full complaint
My 2013 Ford Edge had 44,882 miles on it. With no warning or lights, car was difficult to stop. Hissing noise when brakes applied. Very scary! Took it to Ford dealership. They charged me $167 to diagnose the problem as power brake booster, and said it would take 3-4 weeks to get the part. Ford knows there’s a problem (N102) and supposedly it’s covered for 10 years or 150,000 miles, but I was told that mine would NOT be covered. I took it to an independent repaIr shop. They were able to get the part in three days. It cost me $993.28 to have it repaired. VERY DISAPPOINTED with Ford!! This is a SAFETY ISSUE!, Thank God I wasn’t on a highway when it happened! Is Ford waiting until someone gets killed?
Well driving under normal operating conditions at the posted speed limit of 45 mph I was cut off and apply the brakes rapidly to avoid a collision, at that moment the brake pedal lost its firmness and depressed slowly to the floor with limited breaking ability. After the incident I pulled to the shoulder and noticed that the bra…
Read full complaint
Well driving under normal operating conditions at the posted speed limit of 45 mph I was cut off and apply the brakes rapidly to avoid a collision, at that moment the brake pedal lost its firmness and depressed slowly to the floor with limited breaking ability. After the incident I pulled to the shoulder and noticed that the brake pedal continue to sink to the floor with little to no resistance even after placing in park, shutting down and restarting the vehicle. This condition still persists after break bleeding and checking the entire brake system, my safety was in jeopardy due to the fact that I had limited braking ability and the pedal continue to sink to the floor with no resistance. This has not been evaluated by a dealership or independent mechanic as of this writing and the problem has not been reproduced also there’s been no reports to my insurance, police, the manufacture or any other parties and there were no warning lights, diagnostic trouble codes, or any other Indication as to there being a faulty system or failed ABS pump, master cylinder or hydroboost
The contact owns a 2013 Ford Edge. The contact stated that while depressing the brake pedal to stop the vehicle, the pedal extended to the floor and the braking distance was extended. Additionally, the brake pedal felt spongy when pressed. The vehicle was towed to an independent mechanic who was unable to duplicate the failure. …
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that while depressing the brake pedal to stop the vehicle, the pedal extended to the floor and the braking distance was extended. Additionally, the brake pedal felt spongy when pressed. The vehicle was towed to an independent mechanic who was unable to duplicate the failure. The mechanic indicated that a hissing sound was present while depressing the brake pedal. The vehicle was not repaired. The local dealer and manufacturer were notified of the failure. The failure mileage was 114,000.
my car would not stop when i tried to stop. I tried stopping a second time and the brake pedal went to the floor. i have another replaced the brake booster 2 years ago and now they are saying it is the hcu unit. my car was under recall for booster but mine was not covered as it was made in nov i understand the recall was for 201…
Read full complaint
my car would not stop when i tried to stop. I tried stopping a second time and the brake pedal went to the floor. i have another replaced the brake booster 2 years ago and now they are saying it is the hcu unit. my car was under recall for booster but mine was not covered as it was made in nov i understand the recall was for 2013 made before May. I had the same problem.
i went to stop and the vehile did not stop but continued to roll. I tried stopping a second time the vehile break pedal went to the group. I then had the car towed in to the shop.
When applying the brakes on my 2013 Ford Edge the brake pedal sinks to the floor (soft fading pedal). This always occurred following a quick hard stop, such as is required to avoid an animal or other unforeseen road hazard. Deliberately pushing the brake pedal with another quick, hard application (i.e. slamming the brakes) wou…
Read full complaint
When applying the brakes on my 2013 Ford Edge the brake pedal sinks to the floor (soft fading pedal). This always occurred following a quick hard stop, such as is required to avoid an animal or other unforeseen road hazard. Deliberately pushing the brake pedal with another quick, hard application (i.e. slamming the brakes) would then alleviate the soft pedal issue temporarily, only to have the entire scenario repeat itself. There are no warning lamps, messages or indications that there is a problem. The service department at Sunrise Ford in Fort Pierce, FL confirmed the problem and replaced the brake booster in accordance with Customer Satisfaction Program 13N02 (occurred on 3/5/21 at 81, 896 miles). Replacing the brake booster did not fix the problem. In fact, the soft fading brake pedal sinking to the floor is now continuous, and happens upon every brake application. This most definitely is a safety issue that endangers the vehicle occupants and all others on the road in the vicinity to include pedestrians. It puts everyone at risk because a soft fading brake pedal that goes to the floor delays the braking action of the vehicle, hence a longer stopping distance and possible collision. I have an appointment with the Sunrise Ford Dealership and I have stopped driving this vehicle until the manufacturer/dealership can provide a solution. A manufacturer safety recall is absolutely necessary.
Bakes Booster and Cylinder has to be replaced. When hitting brake pedal doesn't stop car immediatedly and goes very low. Have to step on brake several times for car to start. There seems to be a lot of complaints against 2013 Ford Edge for brake problems.
While turning into a driveway and applying the brake pedal, the pedal traveled to the floorboard, felt spongey and made a hissing sound. The vehicle is currently at the mechanics and was informed that it was not the master cylinder and is now looking to replace the brake booster. No service lights came on; there was no warning…
Read full complaint
While turning into a driveway and applying the brake pedal, the pedal traveled to the floorboard, felt spongey and made a hissing sound. The vehicle is currently at the mechanics and was informed that it was not the master cylinder and is now looking to replace the brake booster. No service lights came on; there was no warning at all.
When my check engine light came on I took my 2013 Ford Edge to my regular mechanic. I was having problems with the brakes causing the car to stall when stopped with my foot on the brake. It was also difficult to stop since the brake pedal would not engage & when it did it went to the floor. It was the brake booster which I paid …
Read full complaint
When my check engine light came on I took my 2013 Ford Edge to my regular mechanic. I was having problems with the brakes causing the car to stall when stopped with my foot on the brake. It was also difficult to stop since the brake pedal would not engage & when it did it went to the floor. It was the brake booster which I paid $966 to have repaired. I later learned that this was under a Ford recall 13N02 for 2010-2013 Edge however my vehicle was not covered because apparently it wasn't built in the Oakville plant!! I feel this should be covered regardless of where my vehicle was built since the issue involves the exact problem described in Ford's "customer satisfaction program 13N02"
Official recalls
214V393000 · Power Train:axle Assembly:axle Shaft
Jul 2, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2014 Ford Edge and Lincoln MKX vehicles manufactured September 2, 2010, to November 30, 2013; 2013-2014 Ford Taurus and Lincoln MKS vehicles manufactured August 25, 2011, to November 30, 2013; and 2013-2014 Ford Flex and Lincoln MKT vehicles manufactured September 12, 2011, to November 30, 2013. In the affected vehicles, the halfshaft retention circlip may not have been properly installed, and as a result, the halfshaft may move outward and disengage from the linkshaft while driving and without prior warning.
Consequence & remedy
Consequence: If the halfshaft and linkshaft become disengaged while driving, power will no longer be transmitted to the wheels, increasing the risk of a vehicle crash. Additionally, if the parking brake is not applied before exiting the vehicle, the vehicle may roll away despite the transmission being placed in 'Park', increasing the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the vehicles to make sure that the halfshaft is properly retained. If it is not, dealers will replace the linkshaft and also replace the halfshaft if it shows evidence of spline damage, free of charge. The recall began on August 4, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S10.
14V002000 · Fuel System, Gasoline
Jan 6, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2013 Edge vehicles manufactured from September 2, 2010, through April 25, 2013, and equipped with 2.0L engines. The fuel line pulse damper metal housing may crack as a result of an improper manufacturing process. A cracked fuel line pulse damper housing may result in a combination of fuel odor, weepage, or a continuous leak while the fuel system is pressurized.
Consequence & remedy
Consequence: A fuel leak in the presence of an ignition source may result in a fire.
Remedy: Ford will notify owners, and dealers will replace the fuel line with one that does not have a damper, free of charge. The safety recall began on February 25, 2014. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 13S13. IMPORTANT: This recall supersedes recall 12V-438. All vehicles that have been remedied under the previous recall need to have the current remedy applied.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE16012 · Door Ajar Warning Light Always On
Opened Sep 28, 2016 · Closed Mar 20, 2017
Status: closed (inferred from source dates) · Interior Lighting; Latches/locks/linkages; Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Additional source detail variants (3)
Interior Lighting
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.