← New search

2013 Ford Edge

Owner reports · Recalls · Investigations

More warning signs than most Edge years

Owner complaints for the 2013 Ford Edge are substantially higher than the model-year median of 724.

About this comparison →

When problems were reported

Mileage at the reported incident

1,793 reports with mileage · 651 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Electrical System. Review the 854 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Service Brakes. Review the 529 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Structure. Review the 300 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

33 crash reports7 fire reports24 injury reports

Service Brakes complaints

529 reports
Clear category filter
Mileage unknown · Jun 1, 2022
Forward Collision AvoidanceService Brakes

The adaptive cruise won’t work, traction control, abs brake warning lights stay on. Ford won’t assist or assume in the responsibility.

NHTSA ODI #11467040

55,320 miles · Jun 1, 2022
Service Brakes

The contact owns a 2013 Ford Edge. The contact stated while depressing the brake pedal to stop the vehicle, the pedal extended to the floor with a hissing sound. Also, the brake pedal was very slow to retract. The vehicle was taken to the local mechanic who changed the rear brake pads and brake rotors however, the failure persis…

Read full complaint

The contact owns a 2013 Ford Edge. The contact stated while depressing the brake pedal to stop the vehicle, the pedal extended to the floor with a hissing sound. Also, the brake pedal was very slow to retract. The vehicle was taken to the local mechanic who changed the rear brake pads and brake rotors however, the failure persisted. The vehicle was reexamined and diagnosed as having a faulty brake booster. The vehicle was not yet repaired. The manufacturer and local dealer were notified of the failure. The failure mileage was 55,320.

NHTSA ODI #11466974

84,900 miles · May 31, 2022
Service Brakes

The contact owns a 2013 Ford Edge. The contact stated that the brake pressure would fail causing the contact to have to excessively depress the brake pedal before the vehicle came to a stop. The vehicle's timing before coming to a complete stop had also increased. The failure occurred intermittently when on an incline, however, …

Read full complaint

The contact owns a 2013 Ford Edge. The contact stated that the brake pressure would fail causing the contact to have to excessively depress the brake pedal before the vehicle came to a stop. The vehicle's timing before coming to a complete stop had also increased. The failure occurred intermittently when on an incline, however, the occurrence had increased. The dealer stated the failure related to a service bulletin regarding the replacement of the brake booster failed however the vehicle had not been repaired. The manufacturer was made aware of the failure however confirmed that the VIN was not included in the service bulletin. The failure mileage was 84,900.

NHTSA ODI #11466759

Mileage unknown · May 29, 2022
Service Brakes

We purchased a 2013 Ford Edge less than a year ago. Brakes went out. The pedal goes all the way down to floor and makes a hissing sound. I researched online and this is the case for hundreds of 2013 Ford Edge owners. Please look this up on carcomplaints.com This is a life or death safety issue. Our vehicle rolled through a stop …

Read full complaint

We purchased a 2013 Ford Edge less than a year ago. Brakes went out. The pedal goes all the way down to floor and makes a hissing sound. I researched online and this is the case for hundreds of 2013 Ford Edge owners. Please look this up on carcomplaints.com This is a life or death safety issue. Our vehicle rolled through a stop sign because the brakes didn't stop us. I'm so worried that I can't have my children ride in this vehicle with me. There was a 13N02 for 2013 Ford Edges replacing the brake booster but not all 2013 ones. My wasn't included. There were no warning lights prior to brakes giving out and they are now so bad. They brake pedal is so low to the floor. I have an appointment on the 6th. They said that this is a known issues with Ford Edges but no recalls have been issued by Ford. Please Talk to Ford so they can issue a recall. There are hundreds of people online with this same problem. Brakes are the scariest issue to have with a car. I don't want hurt/killed.

NHTSA ODI #11466597

75,000 miles · May 18, 2022
Service Brakes

The contact owns a 2013 Ford Edge. The contact stated that while driving at an undisclosed speed, the vehicle made a hissing noise while the brake pedal was depressed. The vehicle was taken to the dealer where it was diagnosed with a tear in the brake booster. The vehicle was not repaired and remained at the dealer. The manufact…

Read full complaint

The contact owns a 2013 Ford Edge. The contact stated that while driving at an undisclosed speed, the vehicle made a hissing noise while the brake pedal was depressed. The vehicle was taken to the dealer where it was diagnosed with a tear in the brake booster. The vehicle was not repaired and remained at the dealer. The manufacturer was made aware of the failure and advised the contact to file a complaint with NHTSA. The contact related the failure to NHTSA ID Number: 10054925 (Service Brakes). The failure mileage was approximately 75,000.

NHTSA ODI #11465210

Mileage unknown · Mar 31, 2022
Service BrakesUnknown Or Other

The brake booster failed, just as is outlined in Ford's Customer Satisfaction Program #13N02, NHTSA #10054925. Ford claims my vehicle was built outside of the dates covered in the CSP and therefore, does not qualify for the warranty extension of the CSP. The booster failure I experienced is identical to that described in the C…

Read full complaint

The brake booster failed, just as is outlined in Ford's Customer Satisfaction Program #13N02, NHTSA #10054925. Ford claims my vehicle was built outside of the dates covered in the CSP and therefore, does not qualify for the warranty extension of the CSP. The booster failure I experienced is identical to that described in the CSP, so it seems obvious that there are more vehicles affected than Ford claims.

NHTSA ODI #11459119

Mileage unknown · Mar 29, 2022
Service Brakes

The afternoon of Friday, March 25, 2022 I was driving over Balcom Canyon and my brake pedal went all the way to the floor with no response! In my almost 30 years of driving I have NEVER experienced something so terrifying! I literally could've died (or caused a collision with another person, endangering everyone involved). I imm…

Read full complaint

The afternoon of Friday, March 25, 2022 I was driving over Balcom Canyon and my brake pedal went all the way to the floor with no response! In my almost 30 years of driving I have NEVER experienced something so terrifying! I literally could've died (or caused a collision with another person, endangering everyone involved). I immediately took my car (2013 Ford Edge Limited) to the dealership where I purchased the vehicle (Valencia). They tell me it's the HCU (Hydraulic Control Unit) and will cost me $2,000 to replace! This is an OBVIOUS safety issue and a matter of life or death. Upon doing more research, I have discovered that this is an ongoing issue with Ford vehicles and I feel it is UNACCEPTABLE to allow people to be put in these types of situations KNOWING of this defect! And to not recall/repair the issue?! Shame on Ford! Something needs to be done. They are putting everyone's lives and safety at risk! I purchased my car new on Labor Day 2013 so I've had it 8.5 years BUT it only has 42,000 miles on it! And it is very well-maintained and in immaculate condition. There were no warning lights or sounds or anything. Just no brakes. On a CANYON road! I feel this is absolutely unacceptable and now I am not even comfortable driving my own car anymore! I was already a bit of an "anxious" driver but now I'm totally traumatized and feel I can't trust my own car's braking system?! Just crazy! Please do something about this NOW

NHTSA ODI #11458851

Mileage unknown · Mar 25, 2022
Service Brakes

Hard brake pedal on trying to stop. Takes a lot of pressure on brake pedal to stop.

NHTSA ODI #11458334

Mileage unknown · Mar 16, 2022
Service Brakes

Brake pedal intermittently goes to the floor when attempting to stop. The brake booster was replaced by dealership under wgat they called a recall but received vehicle back with the same issue. Dealership is now stating Hydraulic Control Unit is the issue noting repair cost 1,700.

NHTSA ODI #11456915

Mileage unknown · Mar 8, 2022
Service Brakes

The brake booster and master cylinder failed on my 2013 Ford Edge, which required extreme applications of pressure to the brake pedal to bring the car to a complete stop (the brake pedal would either sink to floor when being depressed or become extremely stiff when attempting to stop). This has been a serious safety risk, as exc…

Read full complaint

The brake booster and master cylinder failed on my 2013 Ford Edge, which required extreme applications of pressure to the brake pedal to bring the car to a complete stop (the brake pedal would either sink to floor when being depressed or become extremely stiff when attempting to stop). This has been a serious safety risk, as excessive force has been required under normal circumstances to bring the vehicle to a complete stop. Independent mechanics were required to replace both the brake booster and master cylinder to resolve the issues.

NHTSA ODI #11455666

Official recalls

2

14V393000 · Power Train:axle Assembly:axle Shaft

Jul 2, 2014

Ford Motor Company (Ford) is recalling certain model year 2012-2014 Ford Edge and Lincoln MKX vehicles manufactured September 2, 2010, to November 30, 2013; 2013-2014 Ford Taurus and Lincoln MKS vehicles manufactured August 25, 2011, to November 30, 2013; and 2013-2014 Ford Flex and Lincoln MKT vehicles manufactured September 12, 2011, to November 30, 2013. In the affected vehicles, the halfshaft retention circlip may not have been properly installed, and as a result, the halfshaft may move outward and disengage from the linkshaft while driving and without prior warning.

Consequence & remedy

Consequence: If the halfshaft and linkshaft become disengaged while driving, power will no longer be transmitted to the wheels, increasing the risk of a vehicle crash. Additionally, if the parking brake is not applied before exiting the vehicle, the vehicle may roll away despite the transmission being placed in 'Park', increasing the risk of injury to exiting occupants and bystanders.

Remedy: Ford will notify owners, and dealers will inspect the vehicles to make sure that the halfshaft is properly retained. If it is not, dealers will replace the linkshaft and also replace the halfshaft if it shows evidence of spline damage, free of charge. The recall began on August 4, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S10.

14V002000 · Fuel System, Gasoline

Jan 6, 2014

Ford Motor Company (Ford) is recalling certain model year 2012-2013 Edge vehicles manufactured from September 2, 2010, through April 25, 2013, and equipped with 2.0L engines. The fuel line pulse damper metal housing may crack as a result of an improper manufacturing process. A cracked fuel line pulse damper housing may result in a combination of fuel odor, weepage, or a continuous leak while the fuel system is pressurized.

Consequence & remedy

Consequence: A fuel leak in the presence of an ignition source may result in a fire.

Remedy: Ford will notify owners, and dealers will replace the fuel line with one that does not have a damper, free of charge. The safety recall began on February 25, 2014. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 13S13. IMPORTANT: This recall supersedes recall 12V-438. All vehicles that have been remedied under the previous recall need to have the current remedy applied.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

1

PE16012 · Door Ajar Warning Light Always On

Opened Sep 28, 2016 · Closed Mar 20, 2017

Status: closed (inferred from source dates) · Interior Lighting; Latches/locks/linkages; Latches/locks/linkages:doors:latch

The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.

Additional source detail variants (3)

Interior Lighting

The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.

Latches/locks/linkages:doors:latch

The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.

Latches/locks/linkages

The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.