← New search

2013 Ford Edge

Owner reports · Recalls · Investigations

More warning signs than most Edge years

Owner complaints for the 2013 Ford Edge are substantially higher than the model-year median of 724.

About this comparison →

When problems were reported

Mileage at the reported incident

1,793 reports with mileage · 651 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Electrical System. Review the 854 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Service Brakes. Review the 529 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Structure. Review the 300 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

33 crash reports7 fire reports24 injury reports

Service Brakes complaints

529 reports
Clear category filter
Mileage unknown · May 26, 2023
Service Brakes

Three times over the past month I have experienced a soft brake pedal that would go all the way to the floor and the vehicle would fail to stop normally. The first two (2) times where at low speed approaching a gas pump. More frighteningly the third time was at 45 MPH with my young daughter in the vehicle and evasive maneuvers h…

Read full complaint

Three times over the past month I have experienced a soft brake pedal that would go all the way to the floor and the vehicle would fail to stop normally. The first two (2) times where at low speed approaching a gas pump. More frighteningly the third time was at 45 MPH with my young daughter in the vehicle and evasive maneuvers had to be mad to avaoid a collision. After the first time I had the brake pads changed. Earlier on the day of the third incident my vehicle was at a national service center for a brake inspection, because of the alarm from the second incident, and no issue was found. The issue is completely random with no noise, dash lights, warning, or indication of impending failure at all. I have read multiple accounts of 2013 Ford Edge drivers with accounts matching mine detail for detail. Reports of multiple brake booster and master cylinder replacements and HCU replacements with no success. This is extremely dangerous and will eventually result in the loss of life for someone. This needs to be addressed by Ford via recall immediately.

NHTSA ODI #11524091

Mileage unknown · May 19, 2023
Service Brakes

With no warning lights or other apparent issues brake pressure suddenly disappeared resulting in the brake pedal sinking to the floorboard before the vehicle would even slow down or stop. This first happened in September 2022. The issue can better be described in both NHTSA Complaints 11339440 and 11343191. The brake master c…

Read full complaint

With no warning lights or other apparent issues brake pressure suddenly disappeared resulting in the brake pedal sinking to the floorboard before the vehicle would even slow down or stop. This first happened in September 2022. The issue can better be described in both NHTSA Complaints 11339440 and 11343191. The brake master cylinder was replaced. It worked until May 2023 and I am now having the same issue. There is almost no brake pressure. The problem has yet to be resolved. This is a very serious safety risk for both the passengers of this vehicle and others on the road. It is almost impossible to come to a full stop within a few seconds.

NHTSA ODI #11522817

Mileage unknown · May 10, 2023
Service Brakes

The brakes failed to function with no warning whatsoever! The pedal immediately went to the floor with no result. This would have cause an accident had we not been on an empty road with no traffic. The vehicle is available for inspection. The is a HUGE risk to the safety of my family and other drivers and pedestrians who mig…

Read full complaint

The brakes failed to function with no warning whatsoever! The pedal immediately went to the floor with no result. This would have cause an accident had we not been on an empty road with no traffic. The vehicle is available for inspection. The is a HUGE risk to the safety of my family and other drivers and pedestrians who might be struck by a vehicle that cannot stop. This can definitely result in severe injuries or death. The vehicle was taken to a repair shop where the problem could not be duplicated, even though they tried by slowly driving the vehicle for 2 days. For precautions sake, the rotors and pads were replaced and the brake system components checked and fluid bled. We then took the vehicle back and drove it for about a week in various traffic situations without incident. Today, the same failure occurred. By shear grace of God, we were on a road with no traffic again! I have now been reading all the reports on this NHTSA site and am extremely concerned that NHTSA has not forced a recall. This is clearly a repetitive and frequent issue. with Ford Edge vehicles! DO SOMETHING NOW BEFORE SOMEONE DIES OR IS SERIOUSLY INJURED. There were no warning lamps, messages or other symptoms of the problem prior to the failure. This first appeared April, 2023.

NHTSA ODI #11521345

Mileage unknown · Apr 24, 2023
Service Brakes

My 2013 Ford Edge is making a hissing noise when the brakes are applied. It has been a few months; I’ve tried to brush it off that it was just my imagination because my brakes are working (for now), there is nothing leaking, but now there is also a jerk feeling. As I’m driving and then slow down, somewhere between 35-40 mph, the…

Read full complaint

My 2013 Ford Edge is making a hissing noise when the brakes are applied. It has been a few months; I’ve tried to brush it off that it was just my imagination because my brakes are working (for now), there is nothing leaking, but now there is also a jerk feeling. As I’m driving and then slow down, somewhere between 35-40 mph, there is a little jerk or “hiccup” feeling. I have noticed that sometimes the pedal feels hard to press. I’m worried what is going on will eventually cause my brakes to fail and cause injury. Nothing has been inspected yet, but I did research and see that there is a recall for this exact problem. However, I have not received anything in the mail regarding this. I looked up my VIN and found there are 0 recalls for my vehicle. I believe that my vehicle should be included in this recall.

NHTSA ODI #11518622

Mileage unknown · Apr 21, 2023
Service Brakes

We began experiencing a "hissing" noise when the brake pedal was depressed. Additionally, the pedal feels stiff, and occasionally the brakes will not engage at all without significant pressure being applied to the brake pedal. We took the vehicle to a Ford dealership, they ran diagnostics, and they confirmed that the brake boo…

Read full complaint

We began experiencing a "hissing" noise when the brake pedal was depressed. Additionally, the pedal feels stiff, and occasionally the brakes will not engage at all without significant pressure being applied to the brake pedal. We took the vehicle to a Ford dealership, they ran diagnostics, and they confirmed that the brake booster is failing. We discovered that this was a known issue with 2013 Ford Edge vehicles. Ford has a Customer Satisfaction Program (13N02) that was published in its TSB (SB-10054925-6246). This CSP recommends that the brake booster be repaired and extends warranty coverage of the part for certain "2010-2013 model year Edge and MKX vehicles built at the Oakville Assembly Plant from May 3, 2010 through March 28, 2013." I have been told by Ford Motor Company that my vehicle is not covered under this CSP because its VIN was not identified as being affected and, while it was made at Oakville, it was made in November of 2013. Therefore, according to Ford, they are not liable to cover the part replacement despite the fact that the issue we're having is the same issue that Ford has identified in other vehicles of the same make, model year, and built at the same assembly plant.

NHTSA ODI #11518246

Mileage unknown · Apr 20, 2023
Service BrakesUnknown Or OtherWheels

I had my brakes repaired and since having my brakes repaired, I continued to have issues with the suspension, vehicle handling and imbalance (vehicle not stopping properly). I was dropping my friend girl's grandsons off at school and my brakes went out...almost causing me to have a head on collision with the vehicle in front of …

Read full complaint

I had my brakes repaired and since having my brakes repaired, I continued to have issues with the suspension, vehicle handling and imbalance (vehicle not stopping properly). I was dropping my friend girl's grandsons off at school and my brakes went out...almost causing me to have a head on collision with the vehicle in front of me. I was overwhelmed and hysterical! I had taken my vehicle back to the repair shop that replaced my brakes and I tried to explain what happened. I was bewildered because my vehicle didn't have any warning messages of any sort. I remember riding over some bumpy streets and when the traffic slowed down, I pressed my brakes and they were gone. I had to press the brake pedal all the way down to the floor and I wasn't getting any pressure through the brake line at all, which caused me to almost run into the vehicle in front of me. When I pressed the brake to the floor, my vehicle slid rapidly and made a strange noise before I was able to come to a complete stop. We were terrified because I had ran into the curb trying to stop my vehicle! The repair shop mechanic stated that it could be the caliber connected to the brake line, because my vehicle did not have sweaking noises that you usually hear when your brakes need to be replaced. My vehicle is still in need of repairs, I'm afraid while driving it still. I'm bewildered because I honestly don't know what caused my brakes to just go out like that!

NHTSA ODI #11517979

Mileage unknown · Apr 13, 2023
Service Brakes

Brake pedal goes to the floor when you press on the breaks and you hear a sound as it happens

NHTSA ODI #11516965

Mileage unknown · Apr 3, 2023
Service Brakes

5 times in the past 2 years I lost the brakes. Each time the car was going at low speed coming up on a stop sign or traffic light, probably 10-15 mph, and hit a pothole with brakes lightly applied. The ABS kicked in on each of those occasions. The car could still be braked, but the pedal immediately went to the floor and stoppin…

Read full complaint

5 times in the past 2 years I lost the brakes. Each time the car was going at low speed coming up on a stop sign or traffic light, probably 10-15 mph, and hit a pothole with brakes lightly applied. The ABS kicked in on each of those occasions. The car could still be braked, but the pedal immediately went to the floor and stopping distances were increased. The first 4 times it happened, the brakes returned to normal operation after the car sat overnight. After the 4th time I learned that there was a 10-year brake booster extended warranty, so I had that done and all was fine. On the 5th time, just recently, I was again approaching a light in a construction zone at very slow speed, with the brakes lightly applied. I hit a shallow trench that had been dug in the pavement, and the ABS kicked in and the pedal went to the floor. I still had braking power, but it seemed worse than the other 4 times. Unlike those times, the situation did not resolve after the car sat overnight. Brake fluid was filled to the "fill line" and there did not appear to be air in the lines, and there was no leakage of fluid anywhere. I brought the car to the Ford dealer and was told it was an HCU (hydraulic control unit) failure. I searched online and was appalled to see how many people have had the exact same issue, and some reported serious accidents and injuries. Ford says there is a "national backorder" on the HCU, and they have no estimated ship date. In short, my otherwise perfectly good car has become worthless because Ford can't supply the part and it is too dangerous to drive, and I can't trade it in with this defect. I'm fortunate that there was no accident, but I believe this is a very serious safety issue that seems to have been known by Ford for some time. I'm sure you've had similar complaints, and the extent of the problem will become clear with a 5 minute online search. I sincerely believe this is a safety issue that deserves a recall. Thank you.

NHTSA ODI #11515246

Mileage unknown · Apr 3, 2023
Service BrakesUnknown Or Other

Shift to Park warning light comes on even though the car is in park. This component or system failure is known to ford dealers but they state that it is not on the recall listing. It should be because this is a known issue with ford on the 2013 Ford Edge. It requires the whole shifting assembly to be replaced at the cost of t…

Read full complaint

Shift to Park warning light comes on even though the car is in park. This component or system failure is known to ford dealers but they state that it is not on the recall listing. It should be because this is a known issue with ford on the 2013 Ford Edge. It requires the whole shifting assembly to be replaced at the cost of the owner and not the dealership. My car is available for inspection. I have reported this to the Ken Garff St George Ford/Lincoln service and it should be in my file. THis should be a recall issue and not replaced at the cost of the owner

NHTSA ODI #11515171

Mileage unknown · Mar 30, 2023
Service BrakesInjury

The Brake Booster continually fails on this vehicle. It is part of a much larger issue that Ford has acknowledged. On more than 30 occasions the brake booster has failed causing the brakes to fail. The latest happened today (03/30/23) when I had to brake hard to avoid a near head-to-head collision. This time, when the brakes fai…

Read full complaint

The Brake Booster continually fails on this vehicle. It is part of a much larger issue that Ford has acknowledged. On more than 30 occasions the brake booster has failed causing the brakes to fail. The latest happened today (03/30/23) when I had to brake hard to avoid a near head-to-head collision. This time, when the brakes failed I had to swerve into oncoming traffic, then back into my lane after passing the vehicle that came into our lane from a cross street. We were going UNDER the speed limit, which is 45MPH at that intersection. I was finally able to stop after using the manual shifting option to downshift and slow the car enough that the brakes would actually work. The pedal went to the floor when I had to hit the brakes hard to try and avoid the oncoming vehicle. When I contacted Ford I was asking about: Extended warranty coverage on brake booster Campaign# 13N02 I was told by Ford that this vehicle is not covered under this campaign, even though it states that the vehicle must be no more than 10 years old (it is a 2013 vehicle, AND sold as a 2013 vehicle by description from Ford Motor Company) and it is under the 150,000 mile limit. There are a LOT of people that are facing this issue as well, ergo the campaign from Ford. THEY recognize that this is an issue - this should be a recall, not some sort of campaign that Ford is using to try and avoid one. The three of us nearly lost our live THIS time when the brakes failed. How many people WILL die before this actually becomes a recall? The same should be said of the Ford Campaign #19N09 - Door latch failure. The door could come open while driving under this campaign. These should be recalls that Ford MUST fix. Please do not let my Granddaughter get into a crash because of this. She is our ward because of Cerebral Palsy, Autism, Scoliosis and other issues that she faces in life. Isn't that enough for her to deal with? What is this was YOUR Granddaughter? Would it be a recall then?

NHTSA ODI #11514700

Official recalls

2

14V393000 · Power Train:axle Assembly:axle Shaft

Jul 2, 2014

Ford Motor Company (Ford) is recalling certain model year 2012-2014 Ford Edge and Lincoln MKX vehicles manufactured September 2, 2010, to November 30, 2013; 2013-2014 Ford Taurus and Lincoln MKS vehicles manufactured August 25, 2011, to November 30, 2013; and 2013-2014 Ford Flex and Lincoln MKT vehicles manufactured September 12, 2011, to November 30, 2013. In the affected vehicles, the halfshaft retention circlip may not have been properly installed, and as a result, the halfshaft may move outward and disengage from the linkshaft while driving and without prior warning.

Consequence & remedy

Consequence: If the halfshaft and linkshaft become disengaged while driving, power will no longer be transmitted to the wheels, increasing the risk of a vehicle crash. Additionally, if the parking brake is not applied before exiting the vehicle, the vehicle may roll away despite the transmission being placed in 'Park', increasing the risk of injury to exiting occupants and bystanders.

Remedy: Ford will notify owners, and dealers will inspect the vehicles to make sure that the halfshaft is properly retained. If it is not, dealers will replace the linkshaft and also replace the halfshaft if it shows evidence of spline damage, free of charge. The recall began on August 4, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S10.

14V002000 · Fuel System, Gasoline

Jan 6, 2014

Ford Motor Company (Ford) is recalling certain model year 2012-2013 Edge vehicles manufactured from September 2, 2010, through April 25, 2013, and equipped with 2.0L engines. The fuel line pulse damper metal housing may crack as a result of an improper manufacturing process. A cracked fuel line pulse damper housing may result in a combination of fuel odor, weepage, or a continuous leak while the fuel system is pressurized.

Consequence & remedy

Consequence: A fuel leak in the presence of an ignition source may result in a fire.

Remedy: Ford will notify owners, and dealers will replace the fuel line with one that does not have a damper, free of charge. The safety recall began on February 25, 2014. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 13S13. IMPORTANT: This recall supersedes recall 12V-438. All vehicles that have been remedied under the previous recall need to have the current remedy applied.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

1

PE16012 · Door Ajar Warning Light Always On

Opened Sep 28, 2016 · Closed Mar 20, 2017

Status: closed (inferred from source dates) · Interior Lighting; Latches/locks/linkages; Latches/locks/linkages:doors:latch

The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.

Additional source detail variants (3)

Interior Lighting

The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.

Latches/locks/linkages:doors:latch

The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.

Latches/locks/linkages

The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.