← New search

2013 Ford Edge

Owner reports · Recalls · Investigations

More warning signs than most Edge years

Owner complaints for the 2013 Ford Edge are substantially higher than the model-year median of 724.

About this comparison →

When problems were reported

Mileage at the reported incident

1,793 reports with mileage · 651 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Electrical System. Review the 854 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Service Brakes. Review the 529 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Structure. Review the 300 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

33 crash reports7 fire reports24 injury reports

Service Brakes, Hydraulic complaints

105 reports
Clear category filter
100,000 miles · Sep 1, 2026
Service Brakes, Hydraulic

The contact owns a 2013 Ford Edge. The contact stated that while driving at various speeds and attempting to decelerate or come to a complete stop, there was an abnormal sound while depressing the brake pedal. The brake warning light was illuminated. In addition, the contact stated that while in reverse, the rear-view camera dis…

Read full complaint

The contact owns a 2013 Ford Edge. The contact stated that while driving at various speeds and attempting to decelerate or come to a complete stop, there was an abnormal sound while depressing the brake pedal. The brake warning light was illuminated. In addition, the contact stated that while in reverse, the rear-view camera displayed an upside-down image. The vehicle was taken to a local dealer where it was diagnosed and determined that the power booster brake hose needed to be replaced. The vehicle was not repaired. Upon further investigation, the contact associated the failure with an unknown recall; however, the VIN was not under recall. The manufacturer was made aware of the failure, and a case was filed. The failure mileage was approximately 100,000.

NHTSA ODI #11761370

78,000 miles · Aug 6, 2026
Service Brakes, HydraulicCrash

The contact owns a 2013 Ford Edge. The contact stated that while driving approximately 30 MPH, the brake pedal was inoperative. The contact stated that the vehicle drove for several yards, and the contact was unable to reach the parking brake. The vehicle was shifted into park(P) to attempt to stop the vehicle. The contact state…

Read full complaint

The contact owns a 2013 Ford Edge. The contact stated that while driving approximately 30 MPH, the brake pedal was inoperative. The contact stated that the vehicle drove for several yards, and the contact was unable to reach the parking brake. The vehicle was shifted into park(P) to attempt to stop the vehicle. The contact stated that the vehicle crashed into the shrubs in front of the window at an independent mechanic shop, causing the vehicle to come to a stop right before almost crashing into the shop window, which resulted in minor damage to the front bumper. No warning lights were illuminated. The air bags were not deployed. An independent mechanic diagnosed the vehicle and stated that the brake pads and rotors needed to be replaced. The vehicle was repaired; however, the failure persisted. The vehicle was taken to another independent mechanic, where it was diagnosed and determined that the brake booster module needed to be replaced. The vehicle was repaired; however, the failure persisted. The contact researched and was made aware of an unknown recall; however, the VIN was not included. The failure had occurred on several occasions. There were no injuries sustained. A Police report was not filed. The manufacturer was notified of the failure. The failure mileage was approximately 78,000.

NHTSA ODI #11755254

226,424 miles · Jun 10, 2026
Service Brakes, Hydraulic

The contact owns a 2013 Ford Edge. The contact stated that while driving at 25 MPH, the brakes failed, and the vehicle coasted to the side of the road. There was no warning light illuminated. The contact stated that the failure was recurrent. The dealer was notified of the failure, but repairs were pending due to parts unavail…

Read full complaint

The contact owns a 2013 Ford Edge. The contact stated that while driving at 25 MPH, the brakes failed, and the vehicle coasted to the side of the road. There was no warning light illuminated. The contact stated that the failure was recurrent. The dealer was notified of the failure, but repairs were pending due to parts unavailability. The manufacturer was not made aware of the failure. The failure mileage was approximately 226,424.

NHTSA ODI #11743194

125,000 miles · Apr 20, 2026
Service Brakes, Hydraulic

The contact owns a 2013 Ford Edge. The contact stated that while driving at an undisclosed speed, after being cut off by another driver, the contact attempted to make an emergency stop; however, while the brake pedal was depressed, the brake pedal went to the floorboard, extending the braking distance. The vehicle failed to stop…

Read full complaint

The contact owns a 2013 Ford Edge. The contact stated that while driving at an undisclosed speed, after being cut off by another driver, the contact attempted to make an emergency stop; however, while the brake pedal was depressed, the brake pedal went to the floorboard, extending the braking distance. The vehicle failed to stop as intended, increasing the risk of a crash. The dealer was notified of the failure, but the vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 125,000.

NHTSA ODI #11732440

130,000 miles · Oct 27, 2025
Service Brakes, Hydraulic

The contact owns a 2013 Ford Edge. The contact stated that while driving approximately 5 MPH and depressing the brake pedal while exiting a parking lot, the brake pedal went to the floorboard. The contact pumped the brake pedal to stop the vehicle. The contact stated there was no warning light illuminated. The vehicle was not ta…

Read full complaint

The contact owns a 2013 Ford Edge. The contact stated that while driving approximately 5 MPH and depressing the brake pedal while exiting a parking lot, the brake pedal went to the floorboard. The contact pumped the brake pedal to stop the vehicle. The contact stated there was no warning light illuminated. The vehicle was not taken to a local dealer or an independent mechanic. The vehicle was not diagnosed or repaired. The manufacturer was not informed of the failure. The failure mileage was approximately 130,000.

NHTSA ODI #11695824

135,000 miles · Sep 24, 2025
Service Brakes, Hydraulic

The contact owns a 2013 Ford Edge. The contact stated that while driving at a slow speed and taking a right turn, while attempting to depress the brake pedal, the brake pedal felt mushy. The contact stated that excessive force was required to depress the brake pedal. The contact stated that the brake pedal had lost pressure for …

Read full complaint

The contact owns a 2013 Ford Edge. The contact stated that while driving at a slow speed and taking a right turn, while attempting to depress the brake pedal, the brake pedal felt mushy. The contact stated that excessive force was required to depress the brake pedal. The contact stated that the brake pedal had lost pressure for a moment. There was no warning light illuminated. The local dealer was contacted; however, the vehicle was not diagnosed because the VIN was not under an open recall. The vehicle was not repaired. The contact referenced Customer Satisfaction Program: 13N02, as a possible cause for the failure. The manufacturer was notified of the failure. The approximate failure mileage was 135,000.

NHTSA ODI #11689463

110,000 miles · Sep 2, 2025
Service Brakes, Hydraulic

The contact owns a 2013 Ford Edge. The contact stated that while driving approximately 40 MPH, the brake pedal was depressed too slowly for traffic; however, the brake pedal was soft and went to the floorboard. The vehicle was steered to the right and rolled down into a ditch to avoid crashing into the vehicle in front. The cont…

Read full complaint

The contact owns a 2013 Ford Edge. The contact stated that while driving approximately 40 MPH, the brake pedal was depressed too slowly for traffic; however, the brake pedal was soft and went to the floorboard. The vehicle was steered to the right and rolled down into a ditch to avoid crashing into the vehicle in front. The contact stated that the engine was still running. There was no warning light illuminated. The vehicle was turned off and restarted to reset the braking system; however, the brake pedal was still soft. There was no damage to the vehicle, and the contact was able to drive out of the ditch and back to the residence. The vehicle was not yet taken to a local dealer or independent mechanic to be diagnosed or repaired. The contact stated that in 2024, the vehicle was repaired under Customer Satisfaction Program: 13N02 - Brake Booster (Service Brakes, Hydraulic). The manufacturer was informed of the failure. The failure mileage was approximately 110,000.

NHTSA ODI #11684569

146,000 miles · Aug 13, 2025
Service Brakes, Hydraulic

The contact owns a 2013 Ford Edge. The contact stated there was an abnormal air hissing sound coming from the vehicle while depressing the brake pedal. There was no warning light illuminated. In addition to the sound, the brake pedal was firm, requiring extra force on the brake pedal while attempting to stop the vehicle. The con…

Read full complaint

The contact owns a 2013 Ford Edge. The contact stated there was an abnormal air hissing sound coming from the vehicle while depressing the brake pedal. There was no warning light illuminated. In addition to the sound, the brake pedal was firm, requiring extra force on the brake pedal while attempting to stop the vehicle. The contact called a dealer, and an appointment was scheduled for a diagnostic test to be performed on the vehicle. The vehicle was not repaired. The manufacturer was notified of the failure, and the contact was informed that the VIN was not under recall. The manufacturer referred the contact to the NHTSA Hotline to report the failure. The failure mileage was approximately 146,000.

NHTSA ODI #11680347

90,000 miles · Aug 11, 2025
Service Brakes, Hydraulic

The contact owns a 2013 Ford Edge. The contact stated that while driving through a mountainous area, the brake pedal became firm. There was no warning light illuminated. The contact depressed the brake pedal and was forced to pump the brake pedal and depress the brake pedal to the floorboard to stop the vehicle. The contact init…

Read full complaint

The contact owns a 2013 Ford Edge. The contact stated that while driving through a mountainous area, the brake pedal became firm. There was no warning light illuminated. The contact depressed the brake pedal and was forced to pump the brake pedal and depress the brake pedal to the floorboard to stop the vehicle. The contact initially contacted an independent mechanic and was informed that the model vehicle was under recall for the vacuum pump. The dealer was notified of the failure and informed the contact that the VIN was not under recall. The contact was referred to the manufacturer and was informed that the VIN was not included in the recall and referred the contact to the NHTSA Hotline to report the failure. The vehicle was not repaired. The failure mileage was approximately 90,000.

NHTSA ODI #11679939

110,000 miles · Jul 28, 2025
Service Brakes, Hydraulic

The contact owns a 2013 Ford Edge. The contact stated that while depressing the brake pedal to stop the vehicle, the brake pedal extended to the floorboard, causing the braking distance to become extended. The vehicle was taken to the local dealer, who diagnosed the vehicle and determined that the ABS module was faulty and neede…

Read full complaint

The contact owns a 2013 Ford Edge. The contact stated that while depressing the brake pedal to stop the vehicle, the brake pedal extended to the floorboard, causing the braking distance to become extended. The vehicle was taken to the local dealer, who diagnosed the vehicle and determined that the ABS module was faulty and needed to be replaced. The contact was informed that the ABS module was on back order. The vehicle was not yet repaired. The manufacturer was notified of the failure. The failure mileage was 110,000.

NHTSA ODI #11676579

Official recalls

2

14V393000 · Power Train:axle Assembly:axle Shaft

Jul 2, 2014

Ford Motor Company (Ford) is recalling certain model year 2012-2014 Ford Edge and Lincoln MKX vehicles manufactured September 2, 2010, to November 30, 2013; 2013-2014 Ford Taurus and Lincoln MKS vehicles manufactured August 25, 2011, to November 30, 2013; and 2013-2014 Ford Flex and Lincoln MKT vehicles manufactured September 12, 2011, to November 30, 2013. In the affected vehicles, the halfshaft retention circlip may not have been properly installed, and as a result, the halfshaft may move outward and disengage from the linkshaft while driving and without prior warning.

Consequence & remedy

Consequence: If the halfshaft and linkshaft become disengaged while driving, power will no longer be transmitted to the wheels, increasing the risk of a vehicle crash. Additionally, if the parking brake is not applied before exiting the vehicle, the vehicle may roll away despite the transmission being placed in 'Park', increasing the risk of injury to exiting occupants and bystanders.

Remedy: Ford will notify owners, and dealers will inspect the vehicles to make sure that the halfshaft is properly retained. If it is not, dealers will replace the linkshaft and also replace the halfshaft if it shows evidence of spline damage, free of charge. The recall began on August 4, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S10.

14V002000 · Fuel System, Gasoline

Jan 6, 2014

Ford Motor Company (Ford) is recalling certain model year 2012-2013 Edge vehicles manufactured from September 2, 2010, through April 25, 2013, and equipped with 2.0L engines. The fuel line pulse damper metal housing may crack as a result of an improper manufacturing process. A cracked fuel line pulse damper housing may result in a combination of fuel odor, weepage, or a continuous leak while the fuel system is pressurized.

Consequence & remedy

Consequence: A fuel leak in the presence of an ignition source may result in a fire.

Remedy: Ford will notify owners, and dealers will replace the fuel line with one that does not have a damper, free of charge. The safety recall began on February 25, 2014. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 13S13. IMPORTANT: This recall supersedes recall 12V-438. All vehicles that have been remedied under the previous recall need to have the current remedy applied.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

1

PE16012 · Door Ajar Warning Light Always On

Opened Sep 28, 2016 · Closed Mar 20, 2017

Status: closed (inferred from source dates) · Interior Lighting; Latches/locks/linkages; Latches/locks/linkages:doors:latch

The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.

Additional source detail variants (3)

Interior Lighting

The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.

Latches/locks/linkages:doors:latch

The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.

Latches/locks/linkages

The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.