← New search

2012 Ford Edge

Owner reports · Recalls · Investigations

Similar to other model years

Owner complaints for the 2012 Ford Edge do not stand out strongly from the model-year median of 724.

About this comparison →

When problems were reported

Mileage at the reported incident

874 reports with mileage · 260 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Electrical System. Review the 462 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Service Brakes. Review the 247 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Structure. Review the 168 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

26 crash reports5 fire reports12 injury reports

Service Brakes complaints

247 reports
Clear category filter
Mileage unknown · May 25, 2023
Service Brakes

The breaks loose and go down and the car can't stop

NHTSA ODI #11523787

136,000 miles · May 8, 2023
EngineService Brakes

The contact owns a 2012 Ford Edge. The contact stated that while attempting to stop the vehicle, the brake pedal was depressed and extended to the floorboard. The vehicle failed to immediately stop, nearly causing a rear-end collision with another vehicle. The vehicle was taken back to an independent dealer who was unable to det…

Read full complaint

The contact owns a 2012 Ford Edge. The contact stated that while attempting to stop the vehicle, the brake pedal was depressed and extended to the floorboard. The vehicle failed to immediately stop, nearly causing a rear-end collision with another vehicle. The vehicle was taken back to an independent dealer who was unable to determine the cause of the failure. Additionally, while driving at various speeds, the vehicle would not properly accelerate while depressing the accelerator pedal, with the check engine warning light and fuel filler inlet message illuminated. The cause of the failure was not yet determined. The manufacturer and the local dealers were notified but no assistance was offered. The failure mileage was 136,000.

NHTSA ODI #11520962

Mileage unknown · Apr 27, 2023
Service Brakes

Summer 2022 my brakes started giving out … when coming to a stop, the brake pad goes all of the way to the floor makes a sound similar to a pump or a hiss. It “corrected” itself after a few pumps on the brake peddle after about five minutes. It happened a second time so I took it back to the company who had replaced my brakes 2/…

Read full complaint

Summer 2022 my brakes started giving out … when coming to a stop, the brake pad goes all of the way to the floor makes a sound similar to a pump or a hiss. It “corrected” itself after a few pumps on the brake peddle after about five minutes. It happened a second time so I took it back to the company who had replaced my brakes 2/3 yrs prior … they could not find anything wrong w/them. It happened again, I took car back to same place with same results. Later in the year it happened for a 4th time but did not correct itself as it had in the past, I drove home at 30mph for over 30 minutes leaving a lot of space between myself and cars in front. The car sat for about a month then my brother drove it and experienced the same problem. I had the car towed to a mechanic who could not replicate the problem therefore could not fix what he couldn’t find but he did bleed the brakes. I rented a car for a short while but when I did drive it again, the same problem occurred and corrected itself. I took it to a different mechanic who also could not replicate the problem, he tried 3 times. I have experienced the same problem at least three times this year, the last time being last week. My and any passengers safety is at risk daily; fortunately, most times I have been parking or on surface streets when this has happened. There have been no warning signs before the brakes give out. I plan on taking car to dealership this weekend.

NHTSA ODI #11519339

Mileage unknown · Jan 12, 2023
Service Brakes

When braking my brakes hit the floor. I had the booster and master cylinder replaced. 2 years later my car has been at the dealer for 2 months. They replaced the booster again and now say I need a HCU unit. The HCU is on stop sale and now I still am without a car. I have paid 1450.00 for the second booster so far and if they can…

Read full complaint

When braking my brakes hit the floor. I had the booster and master cylinder replaced. 2 years later my car has been at the dealer for 2 months. They replaced the booster again and now say I need a HCU unit. The HCU is on stop sale and now I still am without a car. I have paid 1450.00 for the second booster so far and if they can get the HCU then it’s another 1500.00. My car only has 73,000 miles on it

NHTSA ODI #11501534

123,000 miles · Dec 14, 2022
Service Brakes

The contact owns a 2012 Ford Edge. The contact stated while driving approximately 35 MPH and slowing for traffic, she depressed the brake pedal, and the brake pedal went to the floorboard. The contact stated that she pumped the brake pedal several times and was able to slow the vehicle. The contact stated no warning light was il…

Read full complaint

The contact owns a 2012 Ford Edge. The contact stated while driving approximately 35 MPH and slowing for traffic, she depressed the brake pedal, and the brake pedal went to the floorboard. The contact stated that she pumped the brake pedal several times and was able to slow the vehicle. The contact stated no warning light was illuminated. The contact stated that the brake failure was intermittent. The contact drove the vehicle to an independent mechanic who diagnosed that the failure might be the brake booster. The mechanic bled the brake lines and adjusted the brakes. The vehicle was repaired; however, the brake failure recurred. The vehicle had not been repaired. The manufacturer had been informed of the failure. The failure mileage was approximately 123,000.

NHTSA ODI #11497424

Mileage unknown · Nov 6, 2022
Service Brakes

When I had to make a quick stop the brake pedal went to floor and has been this way had it checked and found THE ABS HCU has a valve sticking and was also told it is a issue on other edge and other ford vehicles scared to drive car a brake issue that really needs fird attention

NHTSA ODI #11492481

Mileage unknown · Oct 23, 2022
Service Brakes

Brake pedal fades to the floor of the vehicle which presents brakes not working. The vehicle has only has a little over 22,000 miles

NHTSA ODI #11490490

Mileage unknown · Oct 14, 2022
Service Brakes

The brake pedal goes all the way to the floor and very little braking is applied to the wheels. The problem appeared while driving. One minute the brakes are fine, the next I have almost no brakes. Very big safety issue! The Ford dealer has diagnosed the problem with the Hydraulic Control Unit (HCU). The car had the same issue …

Read full complaint

The brake pedal goes all the way to the floor and very little braking is applied to the wheels. The problem appeared while driving. One minute the brakes are fine, the next I have almost no brakes. Very big safety issue! The Ford dealer has diagnosed the problem with the Hydraulic Control Unit (HCU). The car had the same issue 5 years ago and was repaired. This is the second time the brakes on this car have failed while driving. No warnings before or after the brake failure.

NHTSA ODI #11489235

72,000 miles · Sep 29, 2022
Service Brakes

The contact owns a 2012 Ford Edge. The contact stated that while reversing into a parking space, the brake pedal became hard to depress and the stopping distance was extended. During the failure, the vehicle nearly crashed into a concrete barrier. The contact indicated that the braking system failure had occurred on multiple occ…

Read full complaint

The contact owns a 2012 Ford Edge. The contact stated that while reversing into a parking space, the brake pedal became hard to depress and the stopping distance was extended. During the failure, the vehicle nearly crashed into a concrete barrier. The contact indicated that the braking system failure had occurred on multiple occasions. The cause of the failure was not yet determined. The local dealer was notified of the failure. The manufacturer was not yet contacted or notified of the failure. The failure mileage was 72,000.

NHTSA ODI #11487020

Mileage unknown · Sep 25, 2022
Electrical SystemService Brakes

2 months after I purchased this vehicle in 2021, I noticed soft brakes, the vehicle displayed low oil pressure it locked up and turned off. Proper oil was added and the brakes appeared normal afterwards. Around mid August 2022, I noticed that when I put pressure on brakes to slow the vehicle, the peddle would sink slowly to th…

Read full complaint

2 months after I purchased this vehicle in 2021, I noticed soft brakes, the vehicle displayed low oil pressure it locked up and turned off. Proper oil was added and the brakes appeared normal afterwards. Around mid August 2022, I noticed that when I put pressure on brakes to slow the vehicle, the peddle would sink slowly to the floor and hard to slow vehicle down. So brakes were inspected and the rear brake pads were worn all the way down and the front brakes were like new.. All four brake pads were replaced with new pads. Well this did not correct the problem. I would still hear a swoosh from the brake peddle when releasing and brakes continued to slowly sink to floor.. So the master cylinder and the vacuum booster were replaced, brake lines were bled over 10 times and problem was still not corrected. No warning lights ever reflected on the vehicle. Now the vehicle will mot start and now i have to tow to repair shop. When I started looking up issues regarding my 2012 Ford Edge SEL, tan color. I noticed this has been a reoccurring issue with this make/model. Also, no repair/recall stickers were attached to the vehicle to address this issue. I purchased this vehicle August 2021 from a dealer in Wilmington, NC.

NHTSA ODI #11486300

Official recalls

3

14V393000 · Power Train:axle Assembly:axle Shaft

Jul 2, 2014

Ford Motor Company (Ford) is recalling certain model year 2012-2014 Ford Edge and Lincoln MKX vehicles manufactured September 2, 2010, to November 30, 2013; 2013-2014 Ford Taurus and Lincoln MKS vehicles manufactured August 25, 2011, to November 30, 2013; and 2013-2014 Ford Flex and Lincoln MKT vehicles manufactured September 12, 2011, to November 30, 2013. In the affected vehicles, the halfshaft retention circlip may not have been properly installed, and as a result, the halfshaft may move outward and disengage from the linkshaft while driving and without prior warning.

Consequence & remedy

Consequence: If the halfshaft and linkshaft become disengaged while driving, power will no longer be transmitted to the wheels, increasing the risk of a vehicle crash. Additionally, if the parking brake is not applied before exiting the vehicle, the vehicle may roll away despite the transmission being placed in 'Park', increasing the risk of injury to exiting occupants and bystanders.

Remedy: Ford will notify owners, and dealers will inspect the vehicles to make sure that the halfshaft is properly retained. If it is not, dealers will replace the linkshaft and also replace the halfshaft if it shows evidence of spline damage, free of charge. The recall began on August 4, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S10.

14V002000 · Fuel System, Gasoline

Jan 6, 2014

Ford Motor Company (Ford) is recalling certain model year 2012-2013 Edge vehicles manufactured from September 2, 2010, through April 25, 2013, and equipped with 2.0L engines. The fuel line pulse damper metal housing may crack as a result of an improper manufacturing process. A cracked fuel line pulse damper housing may result in a combination of fuel odor, weepage, or a continuous leak while the fuel system is pressurized.

Consequence & remedy

Consequence: A fuel leak in the presence of an ignition source may result in a fire.

Remedy: Ford will notify owners, and dealers will replace the fuel line with one that does not have a damper, free of charge. The safety recall began on February 25, 2014. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 13S13. IMPORTANT: This recall supersedes recall 12V-438. All vehicles that have been remedied under the previous recall need to have the current remedy applied.

12V438000 · Fuel System, Gasoline:delivery:hoses, Lines/piping, And Fittings

Sep 7, 2012

Ford is recalling certain 2012 Edge vehicles manufactured from September 2, 2010, through October 31, 2011, equipped with 2.0L engines. The fuel line pulse damper metal housing may crack as a result of an improper manufacturing process. A cracked fuel line pulse damper housing may result in a combination of fuel odor, weepage, or a continuous leak while the fuel system is pressurized.

Consequence & remedy

Consequence: A fuel leak in the presence of an ignition source may result in a fire.

Remedy: Ford will notify owners, and dealers will repair the vehicles free of charge. The safety recall began on September 27, 2012. Owners may contact Ford Motor Company Customer Relationship Center at 1-866-436-7332.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

1

PE16012 · Door Ajar Warning Light Always On

Opened Sep 28, 2016 · Closed Mar 20, 2017

Status: closed (inferred from source dates) · Interior Lighting; Latches/locks/linkages; Latches/locks/linkages:doors:latch

The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.

Additional source detail variants (3)

Interior Lighting

The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.

Latches/locks/linkages:doors:latch

The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.

Latches/locks/linkages

The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.