Driver's door shows door ajar alarm. Even though doors are all securely closed. Doors will not lock while driving the car. Real safety issue for any children in the vehicle.
2011 Ford Edge
Owner reports · Recalls · Investigations
More warning signs than most Edge years
Owner complaints for the 2011 Ford Edge are substantially higher than the model-year median of 724.
About this comparison →How this year compares
Owner complaints by model year
Compare all Edge years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
1,438 reports with mileage · 363 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Electrical System. Review the 686 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Structure. Review the 274 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Service Brakes. Review the 261 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
1,801 reportsUnknown Body control module? Overheating issues Still overheats if left running for longer that a couple minutes
I was taking my Grandkids to school when all of a sudden my brakes went down to the floor. That was the most scary feeling ever no warning light or anything to let me no my brakes where bad.I took my car back the Jd.Byrider they inspected it and said it need a master cylinder they replaced it brakes still doing the same thing t…
Read full complaint
I was taking my Grandkids to school when all of a sudden my brakes went down to the floor. That was the most scary feeling ever no warning light or anything to let me no my brakes where bad.I took my car back the Jd.Byrider they inspected it and said it need a master cylinder they replaced it brakes still doing the same thing they said they was going to try another one then they said it was the brake booster going out or has gone out for me not to worry they sent it to ford they said it had an r dye fed warranty.The car gets to Ford they took a week to look at it they checked it out and said it was the hydraulic control unit that was Faulty. Which would be bout 1800 to fix. I noticed that there has been serval complaints about the same thing that has happen to others brakes just going out with no warning and being told it was a master cylinder.Luckly no injuries has happen yet.My car only has 107,449 miles on it.
Without warning or partial failure the brake pedal goes near to the floor before limited breaking function. The vehicle is not capable of emergency braking. The local dealer confirmed and diagnosed the problem as the brake HCU. There were no warnings or symptoms prior to failure. The estimated cost for repair is $1,900. The HC…
Read full complaint
Without warning or partial failure the brake pedal goes near to the floor before limited breaking function. The vehicle is not capable of emergency braking. The local dealer confirmed and diagnosed the problem as the brake HCU. There were no warnings or symptoms prior to failure. The estimated cost for repair is $1,900. The HCU component is on National back order with unknown availability. The HCU problem appears the same as experienced by Ford with prior models. See Part 573 Safety Recall Report (19V-904).
When driving, you loose power from the gas peddle, the wrench light appears, you must pull of the road, put the vehicle in park, turn it off, and then restart it, this can happen at any time, 20mp or 80mp, you never know when you will loose power of this vehicle. VERY DANGEROUS
The contact owns a 2011 Ford Edge. The contact stated that while driving at an unknown speed, the brake pedal traveled to the floorboard and felt spongey. The vehicle was taken to the dealer where it was diagnosed that the master cylinder needed to be replaced. The vehicle was repaired however, the failure recurred. The vehicle …
Read full complaint
The contact owns a 2011 Ford Edge. The contact stated that while driving at an unknown speed, the brake pedal traveled to the floorboard and felt spongey. The vehicle was taken to the dealer where it was diagnosed that the master cylinder needed to be replaced. The vehicle was repaired however, the failure recurred. The vehicle was taken back to the dealer where it was diagnosed that the master cylinder failed due to the brake booster and both parts needed to be repaired. The vehicle was repaired. The manufacturer was notified of the failure. The approximate failure mileage was 139,898.
Brake Booster issue. Vehicle has been checked by car repair shop (Busse Automotive). Golf Mill Ford has told me car is past extended coverage. Vehicle purchased 2/2011 Having booster replaced by Busse Automotive. Ford Mechanics have been on strike and dealers are backed up, as this is my only vehicle I need to have it replaced …
Read full complaint
Brake Booster issue. Vehicle has been checked by car repair shop (Busse Automotive). Golf Mill Ford has told me car is past extended coverage. Vehicle purchased 2/2011 Having booster replaced by Busse Automotive. Ford Mechanics have been on strike and dealers are backed up, as this is my only vehicle I need to have it replaced to drive safely. The car is in the shop now. Busse Automotive said Ford will work with you on this.
The contact owns a 2011 Ford Edge. The contact stated that while his daughter was driving at an undisclosed speed, the brake pedal would go to the floorboard when depressed. The vehicle was towed to an independent mechanic who diagnosed that the master cylinder was faulty from a brake booster tear. This was the second time the f…
Read full complaint
The contact owns a 2011 Ford Edge. The contact stated that while his daughter was driving at an undisclosed speed, the brake pedal would go to the floorboard when depressed. The vehicle was towed to an independent mechanic who diagnosed that the master cylinder was faulty from a brake booster tear. This was the second time the failure occurred within 2 months. The mechanic had replaced the master cylinder once before when the failure first occurred. The vehicle was not repaired and remained at the shop. The manufacturer was made aware of the failure and informed the contact that there was no recall associated with the VIN. The failure mileage was approximately 131,000.
Twice now, while driving the brake pedal went all the way to the floor. I had to release pedal and hit them again for the car to stop. Thankfully I did'nt hit anyone. The Ford Edge I drive has all new brakes on it, and this happened before I had the brakes done and after. I check online and found many ford edge owners with t…
Read full complaint
Twice now, while driving the brake pedal went all the way to the floor. I had to release pedal and hit them again for the car to stop. Thankfully I did'nt hit anyone. The Ford Edge I drive has all new brakes on it, and this happened before I had the brakes done and after. I check online and found many ford edge owners with the same problem. Its "not" the brake booster, that would be a pedal thats hard to push, I got to believe its a problem with a seal in the master cylinder. I understand Ford is aware of this. Maybe a kick in the pants from the NHTSA will get them to fix this before somebody gets killed. I'm just glad some kid did'nt jump out in front of my car went it happened to me!
The brake booster for my vehicle was starting to decline and make it harder for me to stop my car. When driving my vehicle my brake pedal became very hard to push. While trying to stop it took longer to stop the vehicle from hitting any car in front of me. Problem has been confirmed by servicing dealership. Only been inspected…
Read full complaint
The brake booster for my vehicle was starting to decline and make it harder for me to stop my car. When driving my vehicle my brake pedal became very hard to push. While trying to stop it took longer to stop the vehicle from hitting any car in front of me. Problem has been confirmed by servicing dealership. Only been inspected by the folks at the dealership. There were no indications or warnings that the brake booster was going bad. There was an Extended Warranty Coverage issued by Ford in 2014. The campaign was 13N02 My warranty start date was December 2010. The extended coverage was 150,000 miles or 10 yrs from warranty start date. That puts me 8 months past the coverage period, but my vehicle only has 134,000 miles to date. Your help is greatly appreciated. Thank you
Official recalls
311V128000 · Electrical System:software
Feb 24, 2011
FORD IS RECALLING CERTAIN MODEL YEAR 2011 FORD F-150, F-250, F-350, F-450, F-550, EDGE, AND LINCOLN MKX TRUCKS MANUFACTURED FROM OCTOBER 25, 2010, THROUGH NOVEMBER 20, 2010. THESE VEHICLES WERE INSPECTED USING INTEGRATED DIAGNOSTIC SYSTEM (IDS) THAT HAD A CUSTOM SOFTWARE ROUTINE TO READ THE SUSPECT BODY CONTROL MODULE (BCM) SERIAL NUMBER. BASED ON THE SERIAL NUMBER THE BCM WAS EITHER NOT AFFECTED OR REPLACED. THE CUSTOM SOFTWARE ROUTINE WAS NOT READING THE CORRECT SET OF CHARACTERS, AND WAS NOT ABLE TO IDENTIFY A BCM THAT REQUIRED REPLACEMENT AFFECTED BCMS MAY HAVE THE POTENTIAL FOR AN INTERNAL SHORT.
Consequence & remedy
Consequence: IF AN ELECTRICAL SHORT DEVELOPS, AN OVERHEATING CONDITION MAY OCCUR WHICH COULD RESULT IN A VEHICLE FIRE.
Remedy: DEALER WILL INSPECT THE BODY CONTROL MODULE AND IF NECESSARY REPLACE IT FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MARCH 7, 2011. OWNERS MAY CONTACT FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.
10V659000 · Structure:body
Dec 29, 2010
FORD IS RECALLING CERTAIN MODEL YEAR 2011 F-150, F-250, F-350, F-450, F-550, EDGE AND LINCOLN MKX VEHICLES. DURING A SIX-DAY PRODUCTION PERIOD, THE SUPPLIER OF THE BODY CONTROL MODULE MANUFACTURED MODULES THAT MAY HAVE THE POTENTIAL FOR AN INTERNAL SHORT.
Consequence & remedy
Consequence: IF AN ELECTRICAL SHORT DEVELOPS, AN OVERHEATING CONDITION MAY OCCUR WHICH CAN RESULT IN AN UNATTENDED VEHICLE FIRE.
Remedy: DEALER WILL REPLACE THE BODY CONTROL MODULE IF NECESSARY FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JANUARY 11, 2011. OWNERS MAY CONTACT FORD AT 1-866-436-7332.
10V516000 · Latches/locks/linkages:hatchback/liftgate:lock
Oct 27, 2010
FORD IS RECALLING CERTAIN MODEL YEAR 2011 EDGE AND LINCOLN MKX VEHICLES MANUFACTURED FROM JULY 1, 2010, THROUGH OCTOBER 8, 2010. THESE VEHICLES WERE SHIPPED WITH INCORRECTLY CONFIGURED ELECTRONIC MODULE SETTINGS THAT DISABLE THE LOCKING FUNCTION OF THE LIFTGATE. ACCORDINGLY, THE VEHICLES FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 206, "DOOR LOCKS AND DOOR RETENTION COMPONENTS."
Consequence & remedy
Consequence: THE LIFTGATE LOCK MAY BE DISABLED AND THE DRIVER MAY NOT BE ABLE TO LOCK THE LIFTGATE USING INTERIOR LOCK SWITCHES OR REMOTE KEY FOB BUTTONS.
Remedy: FORD WILL NOTIFY OWNERS AND DEALERS WILL HAVE THE AFFECTED CONTROL MODULES UPDATED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON NOVEMBER 1, 2010. OWNERS MAY CONTACT FORD AT 1-866-436-7332.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE16012 · Door Ajar Warning Light Always On
Opened Sep 28, 2016 · Closed Mar 20, 2017
Status: closed (inferred from source dates) · Interior Lighting; Latches/locks/linkages; Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Additional source detail variants (3)
Interior Lighting
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Illustration