2005 Ford Crown Victoria

Exterior Lighting

The Office of Defects Investigation (ODI) opened an investigation concerning the loss of headlights in model year (MY) 2003-2005 Ford Crown Victoria and Mercury Grand Marquis vehicles. The subject vehicles share the same architecture and major components.ODI has received 636 unique reports (for all submission dates) related to the alleged defect, with owners describing a loss of both low and/or high beam headlights occurring while driving.ODI identified 4 Vehicle Owner Questionnaire ( VOQ) reports alleging minor crash or loss of control incidents due to headlight failures.Drivers alleged running off of the road due to a lack of headlights and one driver reportedly struck a deer.No injuries were indicated in the VOQ crashes.In response to ODI's Information Request (IR) letter, Ford Motor Company (Ford) responded with 4173 unique reports related to the alleged problem.There were a total of 11 crashes reported within that group as well as one injury that occurred when the vehicle struck an unseen object on the side of the road when the headlights failed. Ford also submitted 49,843 warranty claims related to headlight failures.Most reports indicate that the headlights failed without warning leaving the driver with no forward lighting, however some noted the headlights flickered or dimmed prior to turning off.Consumers also noted they were able to hold the flash to pass lever on the steering column mounted stalk to activate the high beams however this is only effective as long as the lever is physically actuated.On December 21st, 2015 Ford notified ODI that it would conduct a safety recall (15V-861) to remedy headlight failures on (MY) 2003-2005 Ford Crown Victoria and Mercury Grand Marquis vehicles.According to Ford, the headlights of the vehicle are controlled by the Lighting Control Module (LCM) located in the engine compartment of the vehicle.The LCM uses an internal relay, mounted to a circuit board, to control power to the headlights. The headlight relay is soldered to the circuit board at six different terminals. The original equipment LCMs were manufactured in a manner that resulted in the solder joints fatiguing and/or cracking as a result of repeated thermal cycling and/or vibration, a defect condition. The condition could be exacerbated by manufacturing quality issues such as an insufficient amount of solder, effecting the continuity between the circuit board and the relay terminal, and resulting in loss of headlights while driving.Other lighting functions are unaffected by this condition.The LCM manufacturing processes were revised to address the defect condition and Ford has been conducting a warranty extension program to cover defective LCMs since late 2013.Under the recall Ford will replace any remaining defective LCMs in recalled vehicles with remedy LCMs once they become available.See NHTSA recall 15V-861 for further details on the safety recall.The recall action initiated by Ford addresses the safety risks of concern to ODI.Accordingly, the investigation is closed.The ODI reports cited above can be reviewed at SaferCar.gov under the identification (ODI) numbers found in the attached list.

Exterior Lighting:headlights

The Office of Defects Investigation (ODI) opened an investigation concerning the loss of headlights in model year (MY) 2003-2005 Ford Crown Victoria and Mercury Grand Marquis vehicles. The subject vehicles share the same architecture and major components.ODI has received 636 unique reports (for all submission dates) related to the alleged defect, with owners describing a loss of both low and/or high beam headlights occurring while driving.ODI identified 4 Vehicle Owner Questionnaire ( VOQ) reports alleging minor crash or loss of control incidents due to headlight failures.Drivers alleged running off of the road due to a lack of headlights and one driver reportedly struck a deer.No injuries were indicated in the VOQ crashes.In response to ODI's Information Request (IR) letter, Ford Motor Company (Ford) responded with 4173 unique reports related to the alleged problem.There were a total of 11 crashes reported within that group as well as one injury that occurred when the vehicle struck an unseen object on the side of the road when the headlights failed. Ford also submitted 49,843 warranty claims related to headlight failures.Most reports indicate that the headlights failed without warning leaving the driver with no forward lighting, however some noted the headlights flickered or dimmed prior to turning off.Consumers also noted they were able to hold the flash to pass lever on the steering column mounted stalk to activate the high beams however this is only effective as long as the lever is physically actuated.On December 21st, 2015 Ford notified ODI that it would conduct a safety recall (15V-861) to remedy headlight failures on (MY) 2003-2005 Ford Crown Victoria and Mercury Grand Marquis vehicles.According to Ford, the headlights of the vehicle are controlled by the Lighting Control Module (LCM) located in the engine compartment of the vehicle.The LCM uses an internal relay, mounted to a circuit board, to control power to the headlights. The headlight relay is soldered to the circuit board at six different terminals. The original equipment LCMs were manufactured in a manner that resulted in the solder joints fatiguing and/or cracking as a result of repeated thermal cycling and/or vibration, a defect condition. The condition could be exacerbated by manufacturing quality issues such as an insufficient amount of solder, effecting the continuity between the circuit board and the relay terminal, and resulting in loss of headlights while driving.Other lighting functions are unaffected by this condition.The LCM manufacturing processes were revised to address the defect condition and Ford has been conducting a warranty extension program to cover defective LCMs since late 2013.Under the recall Ford will replace any remaining defective LCMs in recalled vehicles with remedy LCMs once they become available.See NHTSA recall 15V-861 for further details on the safety recall.The recall action initiated by Ford addresses the safety risks of concern to ODI.Accordingly, the investigation is closed.The ODI reports cited above can be reviewed at SaferCar.gov under the identification (ODI) numbers found in the attached list.

Exterior Lighting

In a letter dated October 2, 2014 the Office of Defects Investigation (ODI) was initially petitioned by the North Carolina Consumers Council, Inc. requesting a defect investigation of an alleged defect condition resulting in headlight and/or exterior lighting failure on 2003-2005 Ford Crown Victoria and Mercury Grand Marquis vehicles.ODI analyzed Vehicle Owner Questionnaire (VOQ) complaints received from consumers and identified a total of 605 reports (for all submission dates) alleging headlight failure.The complaints indicate failures of both low beam headlights typically while driving, a defect condition that was evaluated under a prior ODI investigation (PE08066).Most consumer VOQs indicate that the headlights failed suddenly and without warning leaving the driver with no forward lighting, however some report the headlights flickered or dimmed prior to turning off.In some cases drivers were able to turn the headlights back on after a period of time while others reported the headlights would not come back on at all.Consumers noted they were able to hold the flash to pass lever on the steering column mounted stalk to activate the high beams however this is only effective as long as the lever is actuated.ODI identified 4 VOQ reports alleging minor crash or loss of control incidents due to headlight failures.Drivers indicated running off of the road due to a lack of headlights and one driver reportedly struck a deer.No injuries were indicated in the VOQ crashes.In response to ODI's April 7, 2015 Information Request letter, Ford provided data indicating it has received 3,092 complaints of failed headlights related to the Lighting Control Module (LCM), a device that controls the headlights and other lighting functions.This number includes the complaints Ford reviewed and classified as headlight failure due specifically to the LCM.Within Ford's complaints, there are 11 reports alleging a crash occurred.These drivers reported hitting objects, including other vehicles after the headlights failed causing damage to the affected vehicles.One driver was injured when their car struck an unseen object in the road, jerking the steering wheel from their hands and injuring their shoulder.In total 15 crash allegations were identified, all of which have occurred since ODI's prior evaluation of this issue.This petition has been granted.Preliminary Evaluation PE15-028 has been opened to assess the scope, frequency, and safety-related consequences of the alleged defect.The ODI reports cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SarchNHTSAID under the identification (ODI) numbers found in the attached list.

Exterior Lighting:headlights

In a letter dated October 2, 2014 the Office of Defects Investigation (ODI) was initially petitioned by the North Carolina Consumers Council, Inc. requesting a defect investigation of an alleged defect condition resulting in headlight and/or exterior lighting failure on 2003-2005 Ford Crown Victoria and Mercury Grand Marquis vehicles.ODI analyzed Vehicle Owner Questionnaire (VOQ) complaints received from consumers and identified a total of 605 reports (for all submission dates) alleging headlight failure.The complaints indicate failures of both low beam headlights typically while driving, a defect condition that was evaluated under a prior ODI investigation (PE08066).Most consumer VOQs indicate that the headlights failed suddenly and without warning leaving the driver with no forward lighting, however some report the headlights flickered or dimmed prior to turning off.In some cases drivers were able to turn the headlights back on after a period of time while others reported the headlights would not come back on at all.Consumers noted they were able to hold the flash to pass lever on the steering column mounted stalk to activate the high beams however this is only effective as long as the lever is actuated.ODI identified 4 VOQ reports alleging minor crash or loss of control incidents due to headlight failures.Drivers indicated running off of the road due to a lack of headlights and one driver reportedly struck a deer.No injuries were indicated in the VOQ crashes.In response to ODI's April 7, 2015 Information Request letter, Ford provided data indicating it has received 3,092 complaints of failed headlights related to the Lighting Control Module (LCM), a device that controls the headlights and other lighting functions.This number includes the complaints Ford reviewed and classified as headlight failure due specifically to the LCM.Within Ford's complaints, there are 11 reports alleging a crash occurred.These drivers reported hitting objects, including other vehicles after the headlights failed causing damage to the affected vehicles.One driver was injured when their car struck an unseen object in the road, jerking the steering wheel from their hands and injuring their shoulder.In total 15 crash allegations were identified, all of which have occurred since ODI's prior evaluation of this issue.This petition has been granted.Preliminary Evaluation PE15-028 has been opened to assess the scope, frequency, and safety-related consequences of the alleged defect.The ODI reports cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SarchNHTSAID under the identification (ODI) numbers found in the attached list.

Engine And Engine Cooling:exhaust System

On July 7, 2014 the Office of Defects Investigation (ODI) opened a preliminary evaluation based on five complaints (VOQs) alleging incidents ofinterference between dislodged exhaust manifold heat shields and the lower steering shaft/knuckle, including one alleging the interference resulted in a crash on a highway entrance ramp. Since opening this investigation, ODI has received four additional owner complaints.One indicated that the shield was removed before binding could occur.The other three occurred at low speed and produced some momentary steering binding that was overcome by the driver when additional steering effort was applied.Once the shield was repaired or removed, the steering returned to normal.The single incident ODI identified as a possible crash (VOQ No. 10578715) related to this condition could not be verified and the description of the crash in the complaint was not supported by the police accident report.No additional crash allegations have been identified related to the alleged defect condition.Information provided by Ford in its September 10, 2014 response to ODI's information request letter identified 10 additional incidents resulting in a low rate of 1.6 incidents per 100,000 vehicles sold in vehicles ranging from 7 to 11 years in service.Six of these incidents were reported by a single source, a state police fleet that corrected the problems in March 2011 and has not reported any additional failures since.Ford also reported 5 warranty claims, but these incidents occurred at very low mileages and appeared to be caused by loose or missing heat shield attachment hardware rather than the corrosion condition that was the cause of the more recent incidents and the focus of this investigation.This investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The Agency will continue to monitor complaints and other information relating to the alleged defect in the subject vehicles and take further action in the future if warranted.The following VOQs are associated with this investigation:10643753, 10615584, 10611362, 10610451, 10578715, 10479681, 10471833, 10317493.

Steering

On July 7, 2014 the Office of Defects Investigation (ODI) opened a preliminary evaluation based on five complaints (VOQs) alleging incidents ofinterference between dislodged exhaust manifold heat shields and the lower steering shaft/knuckle, including one alleging the interference resulted in a crash on a highway entrance ramp. Since opening this investigation, ODI has received four additional owner complaints.One indicated that the shield was removed before binding could occur.The other three occurred at low speed and produced some momentary steering binding that was overcome by the driver when additional steering effort was applied.Once the shield was repaired or removed, the steering returned to normal.The single incident ODI identified as a possible crash (VOQ No. 10578715) related to this condition could not be verified and the description of the crash in the complaint was not supported by the police accident report.No additional crash allegations have been identified related to the alleged defect condition.Information provided by Ford in its September 10, 2014 response to ODI's information request letter identified 10 additional incidents resulting in a low rate of 1.6 incidents per 100,000 vehicles sold in vehicles ranging from 7 to 11 years in service.Six of these incidents were reported by a single source, a state police fleet that corrected the problems in March 2011 and has not reported any additional failures since.Ford also reported 5 warranty claims, but these incidents occurred at very low mileages and appeared to be caused by loose or missing heat shield attachment hardware rather than the corrosion condition that was the cause of the more recent incidents and the focus of this investigation.This investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The Agency will continue to monitor complaints and other information relating to the alleged defect in the subject vehicles and take further action in the future if warranted.The following VOQs are associated with this investigation:10643753, 10615584, 10611362, 10610451, 10578715, 10479681, 10471833, 10317493.

Steering:column

In its recall notice dated August 26, 2013, Ford Motor Company (Ford) notified NHTSA of a safety defect condition that may result in loss of steering in approximately 355,000 model year (MY) 2005 through 2011 Ford Crown Victoria and Mercury Grand Marquis vehicles built at the St. Thomas Assembly Plant, MY 2005 through 2007 Lincoln Town Car vehicles built at the Wixom Assembly Plant, and certain MY 2008 through 2011 Lincoln Town Car vehicles built at the St. Thomas Assembly Plant and that are currently registered or were originally sold in Connecticut, Delaware, the District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, or Wisconsin (NHTSA Recall 13V-385, Ford Recall 13S08).Ford's recall addresses a corrosion related defect in the lower intermediate shaft that may result in separation of the steering column lower bearing and loss of steering control.Ford's recall will remedy the defect condition by instructing dealers to replace the lower intermediate shaft and to inspect and repair the upper intermediate shaft and steering column lower bearing as necessary.A retaining clip will be installed if the lower bearing has separated.Ford's investigation of steering column separations in the subject vehicles identified a defect condition in the lower intermediate shaft that could result in separation of the column lower bearing.According to Ford's August 26th defect report, severe corrosion of the lower intermediate shaft may cause the lower intermediate shaft swing link joint(s) to stiffen or seize.Ford determined that forces acting on the upper intermediate shaft because of seized swing links may eventually cause the upper intermediate shaft to collapse, which may result in separation of the column lower bearing and loss of steering control.Analysis of ODI complaints and Ford complaints and warranty identified 22 incidents of steering separation (12 complaints and 10 non-duplicative warranty claims) that may be related to the lower intermediate shaft defect condition.All 22 incidents involved vehicles in the recall region, where 419,210 or roughly half (52%), of the subject vehicles were sold.Ford's investigation also determined that column lower bearing separation may occur in vehicles that experienced upper intermediate shaft collapse in prior frontal impact collisions if the shaft was not properly diagnosed and repaired.Ford identified 13 steering separation incidents outside the recall region (6 complaints and 7 non-duplicative warranty claims) where 386,003 of the subject vehicles were sold.Ford did not find evidence of the lower intermediate shaft corrosion issue in these vehicles.Six of the vehicles had known prior collisions and the histories of the remaining 7 were unknown.To address concerns with possible steering separations in vehicles outside the region for safety recall 13V-385, Ford is conducting a Regional Program (13R01) to inspect and repair the steering assemblies of those vehicles as necessary.The lower intermediate shaft will be replaced only if it fails the inspection, the upper intermediate shaft will be repaired if it fails a Ford-specified measurement test.In the event the steering column lower bearings are found out of position, they will be re-seated and secured with a retaining clip.Based on Ford's field actions, this investigation is closed.The VOQs cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10505992, 10479893, 10477192, 10475950, 10474596

Steering

In its recall notice dated August 26, 2013, Ford Motor Company (Ford) notified NHTSA of a safety defect condition that may result in loss of steering in approximately 355,000 model year (MY) 2005 through 2011 Ford Crown Victoria and Mercury Grand Marquis vehicles built at the St. Thomas Assembly Plant, MY 2005 through 2007 Lincoln Town Car vehicles built at the Wixom Assembly Plant, and certain MY 2008 through 2011 Lincoln Town Car vehicles built at the St. Thomas Assembly Plant and that are currently registered or were originally sold in Connecticut, Delaware, the District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, or Wisconsin (NHTSA Recall 13V-385, Ford Recall 13S08).Ford's recall addresses a corrosion related defect in the lower intermediate shaft that may result in separation of the steering column lower bearing and loss of steering control.Ford's recall will remedy the defect condition by instructing dealers to replace the lower intermediate shaft and to inspect and repair the upper intermediate shaft and steering column lower bearing as necessary.A retaining clip will be installed if the lower bearing has separated.Ford's investigation of steering column separations in the subject vehicles identified a defect condition in the lower intermediate shaft that could result in separation of the column lower bearing.According to Ford's August 26th defect report, severe corrosion of the lower intermediate shaft may cause the lower intermediate shaft swing link joint(s) to stiffen or seize.Ford determined that forces acting on the upper intermediate shaft because of seized swing links may eventually cause the upper intermediate shaft to collapse, which may result in separation of the column lower bearing and loss of steering control.Analysis of ODI complaints and Ford complaints and warranty identified 22 incidents of steering separation (12 complaints and 10 non-duplicative warranty claims) that may be related to the lower intermediate shaft defect condition.All 22 incidents involved vehicles in the recall region, where 419,210 or roughly half (52%), of the subject vehicles were sold.Ford's investigation also determined that column lower bearing separation may occur in vehicles that experienced upper intermediate shaft collapse in prior frontal impact collisions if the shaft was not properly diagnosed and repaired.Ford identified 13 steering separation incidents outside the recall region (6 complaints and 7 non-duplicative warranty claims) where 386,003 of the subject vehicles were sold.Ford did not find evidence of the lower intermediate shaft corrosion issue in these vehicles.Six of the vehicles had known prior collisions and the histories of the remaining 7 were unknown.To address concerns with possible steering separations in vehicles outside the region for safety recall 13V-385, Ford is conducting a Regional Program (13R01) to inspect and repair the steering assemblies of those vehicles as necessary.The lower intermediate shaft will be replaced only if it fails the inspection, the upper intermediate shaft will be repaired if it fails a Ford-specified measurement test.In the event the steering column lower bearings are found out of position, they will be re-seated and secured with a retaining clip.Based on Ford's field actions, this investigation is closed.The VOQs cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10505992, 10479893, 10477192, 10475950, 10474596

Steering:column

In the subject vehicles, the mechanical connection between the steering wheel and rack and pinion steering assembly consist of the steering column and an upper and lower intermediate shaft.A disconnection of any of these components from the steering system can create a loss of steering control.Allegations of a loss of steering control incidents reviewed during the Preliminary Evaluation PE12-025 appear to be related to a separation of the upper and lower shafts within the steering the column. In response to the Office of Defects Investigation's (ODI) Information Request (IR) during PE12-025, Ford provided 2 complaints and 9 warranty claims related to the alleged defect in the subject vehicles (see Figure 1 for an exemplar picture).ODI has received 5 complaints related to the alleged defect, including 1 related to an incident reported in one of the Ford complaints.The incident rate involving subject vehicles is 7.7 per 100,000 vehicles (15 total incidents).Five of the 15 incident vehicles were associated with a prior history report of a frontal impact incident.ODI also analyzed field data for MY 2005 through MY 2008 non-CVPI Crown Victoria and Grand Marquis models and MY 2009 through MY 2011 CVPI models, which use a similar steering column and intermediate shaft design. This analysis identified 4 reports from Ford and 2 complaints to ODI, including 1 duplicative of a complaint provided by Ford, resulting in 5 total incidents and an incident rate of 1.1 per 100,000 vehicles for a vehicle population of approximately 436,000 vehicles. In the peer vehicle analysis, 4 of 5 incident vehicles had a prior history report of a frontal impact incident.ODI also identified 42 reports (39 reports associated with subject vehicles and 3 reports associated peer vehicles) of the lower steering column shaft bearing displacement that did not result in complete separations of the upper to lower steering column shafts (see Figure 2). Vehicles with this condition were identified during inspections of police fleets or during vehicle repairs for complaints of looseness, binding or noise in the steering system while turning.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA13-004) has been opened to further assess the scope, frequency, consequence, and contributing factors to the steering column shaft separations.The VOQs associated with the opening of this investigation and a loss of steering control are: 10347404, 10474596, 10475950, 10477192, and 10479893.

Steering

In the subject vehicles, the mechanical connection between the steering wheel and rack and pinion steering assembly consist of the steering column and an upper and lower intermediate shaft.A disconnection of any of these components from the steering system can create a loss of steering control.Allegations of a loss of steering control incidents reviewed during the Preliminary Evaluation PE12-025 appear to be related to a separation of the upper and lower shafts within the steering the column. In response to the Office of Defects Investigation's (ODI) Information Request (IR) during PE12-025, Ford provided 2 complaints and 9 warranty claims related to the alleged defect in the subject vehicles (see Figure 1 for an exemplar picture).ODI has received 5 complaints related to the alleged defect, including 1 related to an incident reported in one of the Ford complaints.The incident rate involving subject vehicles is 7.7 per 100,000 vehicles (15 total incidents).Five of the 15 incident vehicles were associated with a prior history report of a frontal impact incident.ODI also analyzed field data for MY 2005 through MY 2008 non-CVPI Crown Victoria and Grand Marquis models and MY 2009 through MY 2011 CVPI models, which use a similar steering column and intermediate shaft design. This analysis identified 4 reports from Ford and 2 complaints to ODI, including 1 duplicative of a complaint provided by Ford, resulting in 5 total incidents and an incident rate of 1.1 per 100,000 vehicles for a vehicle population of approximately 436,000 vehicles. In the peer vehicle analysis, 4 of 5 incident vehicles had a prior history report of a frontal impact incident.ODI also identified 42 reports (39 reports associated with subject vehicles and 3 reports associated peer vehicles) of the lower steering column shaft bearing displacement that did not result in complete separations of the upper to lower steering column shafts (see Figure 2). Vehicles with this condition were identified during inspections of police fleets or during vehicle repairs for complaints of looseness, binding or noise in the steering system while turning.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA13-004) has been opened to further assess the scope, frequency, consequence, and contributing factors to the steering column shaft separations.The VOQs associated with the opening of this investigation and a loss of steering control are: 10347404, 10474596, 10475950, 10477192, and 10479893.

Wheels

DURING A SEPTEMBER 23, 2004 MEETING AND IN SUBSEQUENT DISCUSSIONS IN NOVEMBER, FORD ADVISED THE OFFICE OF DEFECTS INVESTIGATION (ODI) OF THEIR PLANS TO INTRODUCE AN IMPROVED STEEL WHEEL FOR MANUFACTURING AND SERVICE COMPONENT USE ON THE SUBJECT VEHICLES, INDICATING THIS WOULD OCCUR IN DECEMBER 2004.THE NEW WHEEL DESIGN INCORPORATES AN ADDITIONAL MANUFACTURING PROCESS (SHOT PEENING) WHICH LOWERS TENSILE STRESS IN THE SURFACE LAYER OF THE RIM MATERIAL ADJACENT TO THE CIRCUMFERENTIAL WELD. THEORETICALLY THIS SHOULD IMPROVE RIM DURABILITY BY REDUCING FATIGUE CRACK INITIATION SITES.INDICATIONS FROM FORD?S ACCELERATED TESTING METHODS SHOW AN IMPROVEMENT IN THE PERFORMANCE OF THE NEW WHEEL.IN ADDITION TO PRIOR SAFETY RECALL 03V279 AND SERVICE ACTION (SA) 03M03, FORD WILL ANNOUNCE A NEW EXTENDED WARRANTY SA FOR VEHICLES BUILT PRIOR TO DECEMBER 2004 THAT SUFFER RIM FRACTURES IN SERVICE.THE NEW WHEEL DESIGN WILL BE USED AS A REMEDY.FORD ADVISES THAT A SA IS SUFFICIENT FOR ADDRESSING FUTURE WHEEL FAILURES (INCLUDING RECALL 03V279 REMEDY WHEEL FAILURES) BECAUSE: 1) FAILURE RATES ARE LOW BASED ON FORD?S ANALYSIS, AND 2) DRIVER WARNINGS (REPETITIVE SLOW AIR LOSS, AND OR STEERING WHEEL VIBRATION) ALLOW EARLY AND SAFE DETECTION OF CRACKED WHEELS.ODI HAS RECEIVED 25 VEHICLE OWNER QUESTIONNAIRE (VOQ) REPORTS (INVOLVING 22 VEHICLES) WHICH ALLEGE A RIM FRACTURE OF ONE OR MORE STEEL WHEELS.ABOUT HALF THE REPORTS INVOLVE VEHICLES BUILT WITH THE REMEDY WHEEL USED FOR RECALL 03V279, AND MOST OF THE REMAINING VEHICLES WERE SUBJECT TO THE RECALL.THE PROCESS OF IDENTIFYING PERTINENT FORD COMPLAINTS IS MADE DIFFICULT BY FORD?S PRIOR RECALL AND WARRANTY PROGRAM ACTIVITIES.THE MANUFACTURER COMPLAINT AND WARRANTY COUNTS, WHICH PRIMARILY INVOLVE FAILURES OF RECALL 03V279 REMEDY WHEELS, ARE BASED ON ANALYSIS CONDUCTED TO DATE AND ARE CONSIDERED TO BE CONSERVATIVE.FURTHER INVESTIGATION IS REQUIRED, THUS ODI IS UPGRADING THIS INVESTIGATION TO AN ENGINEERING ANALYSIS (EA).DURING THE EA, PERTINENT FAILURE REPORTS AND CONSEQUENCES WILL BE IDENTIFIED AND REVIEWED.ODI AND FORD WILL DISCUSS DETAILS FOR CONDUCTING AN AUDIT ANALYSIS OF FAILED WHEELS REPLACED UNDER THE NEW SA.ADDITIONALLY, ODI IS AWAITING FORD?S LAB ANALYSIS OF TWO WHEELS WHICH WERE THE SUBJECT OF VOQ REPORTS, ONE OF WHICH WAS INVOLVED IN THE NOTED CRASH EVENT.A DETERMINATION WILL BE MADE AS TO WHETHER FORD?S SERVICE ACTION IS SUFFICIENT FOR ADDRESSING ONGOING RIM FRACTURES.

Wheels:hubcap/cover

DURING A SEPTEMBER 23, 2004 MEETING AND IN SUBSEQUENT DISCUSSIONS IN NOVEMBER, FORD ADVISED THE OFFICE OF DEFECTS INVESTIGATION (ODI) OF THEIR PLANS TO INTRODUCE AN IMPROVED STEEL WHEEL FOR MANUFACTURING AND SERVICE COMPONENT USE ON THE SUBJECT VEHICLES, INDICATING THIS WOULD OCCUR IN DECEMBER 2004.THE NEW WHEEL DESIGN INCORPORATES AN ADDITIONAL MANUFACTURING PROCESS (SHOT PEENING) WHICH LOWERS TENSILE STRESS IN THE SURFACE LAYER OF THE RIM MATERIAL ADJACENT TO THE CIRCUMFERENTIAL WELD. THEORETICALLY THIS SHOULD IMPROVE RIM DURABILITY BY REDUCING FATIGUE CRACK INITIATION SITES.INDICATIONS FROM FORD?S ACCELERATED TESTING METHODS SHOW AN IMPROVEMENT IN THE PERFORMANCE OF THE NEW WHEEL.IN ADDITION TO PRIOR SAFETY RECALL 03V279 AND SERVICE ACTION (SA) 03M03, FORD WILL ANNOUNCE A NEW EXTENDED WARRANTY SA FOR VEHICLES BUILT PRIOR TO DECEMBER 2004 THAT SUFFER RIM FRACTURES IN SERVICE.THE NEW WHEEL DESIGN WILL BE USED AS A REMEDY.FORD ADVISES THAT A SA IS SUFFICIENT FOR ADDRESSING FUTURE WHEEL FAILURES (INCLUDING RECALL 03V279 REMEDY WHEEL FAILURES) BECAUSE: 1) FAILURE RATES ARE LOW BASED ON FORD?S ANALYSIS, AND 2) DRIVER WARNINGS (REPETITIVE SLOW AIR LOSS, AND OR STEERING WHEEL VIBRATION) ALLOW EARLY AND SAFE DETECTION OF CRACKED WHEELS.ODI HAS RECEIVED 25 VEHICLE OWNER QUESTIONNAIRE (VOQ) REPORTS (INVOLVING 22 VEHICLES) WHICH ALLEGE A RIM FRACTURE OF ONE OR MORE STEEL WHEELS.ABOUT HALF THE REPORTS INVOLVE VEHICLES BUILT WITH THE REMEDY WHEEL USED FOR RECALL 03V279, AND MOST OF THE REMAINING VEHICLES WERE SUBJECT TO THE RECALL.THE PROCESS OF IDENTIFYING PERTINENT FORD COMPLAINTS IS MADE DIFFICULT BY FORD?S PRIOR RECALL AND WARRANTY PROGRAM ACTIVITIES.THE MANUFACTURER COMPLAINT AND WARRANTY COUNTS, WHICH PRIMARILY INVOLVE FAILURES OF RECALL 03V279 REMEDY WHEELS, ARE BASED ON ANALYSIS CONDUCTED TO DATE AND ARE CONSIDERED TO BE CONSERVATIVE.FURTHER INVESTIGATION IS REQUIRED, THUS ODI IS UPGRADING THIS INVESTIGATION TO AN ENGINEERING ANALYSIS (EA).DURING THE EA, PERTINENT FAILURE REPORTS AND CONSEQUENCES WILL BE IDENTIFIED AND REVIEWED.ODI AND FORD WILL DISCUSS DETAILS FOR CONDUCTING AN AUDIT ANALYSIS OF FAILED WHEELS REPLACED UNDER THE NEW SA.ADDITIONALLY, ODI IS AWAITING FORD?S LAB ANALYSIS OF TWO WHEELS WHICH WERE THE SUBJECT OF VOQ REPORTS, ONE OF WHICH WAS INVOLVED IN THE NOTED CRASH EVENT.A DETERMINATION WILL BE MADE AS TO WHETHER FORD?S SERVICE ACTION IS SUFFICIENT FOR ADDRESSING ONGOING RIM FRACTURES.

Wheels:hub

DURING A SEPTEMBER 23, 2004 MEETING AND IN SUBSEQUENT DISCUSSIONS IN NOVEMBER, FORD ADVISED THE OFFICE OF DEFECTS INVESTIGATION (ODI) OF THEIR PLANS TO INTRODUCE AN IMPROVED STEEL WHEEL FOR MANUFACTURING AND SERVICE COMPONENT USE ON THE SUBJECT VEHICLES, INDICATING THIS WOULD OCCUR IN DECEMBER 2004.THE NEW WHEEL DESIGN INCORPORATES AN ADDITIONAL MANUFACTURING PROCESS (SHOT PEENING) WHICH LOWERS TENSILE STRESS IN THE SURFACE LAYER OF THE RIM MATERIAL ADJACENT TO THE CIRCUMFERENTIAL WELD. THEORETICALLY THIS SHOULD IMPROVE RIM DURABILITY BY REDUCING FATIGUE CRACK INITIATION SITES.INDICATIONS FROM FORD?S ACCELERATED TESTING METHODS SHOW AN IMPROVEMENT IN THE PERFORMANCE OF THE NEW WHEEL.IN ADDITION TO PRIOR SAFETY RECALL 03V279 AND SERVICE ACTION (SA) 03M03, FORD WILL ANNOUNCE A NEW EXTENDED WARRANTY SA FOR VEHICLES BUILT PRIOR TO DECEMBER 2004 THAT SUFFER RIM FRACTURES IN SERVICE.THE NEW WHEEL DESIGN WILL BE USED AS A REMEDY.FORD ADVISES THAT A SA IS SUFFICIENT FOR ADDRESSING FUTURE WHEEL FAILURES (INCLUDING RECALL 03V279 REMEDY WHEEL FAILURES) BECAUSE: 1) FAILURE RATES ARE LOW BASED ON FORD?S ANALYSIS, AND 2) DRIVER WARNINGS (REPETITIVE SLOW AIR LOSS, AND OR STEERING WHEEL VIBRATION) ALLOW EARLY AND SAFE DETECTION OF CRACKED WHEELS.ODI HAS RECEIVED 25 VEHICLE OWNER QUESTIONNAIRE (VOQ) REPORTS (INVOLVING 22 VEHICLES) WHICH ALLEGE A RIM FRACTURE OF ONE OR MORE STEEL WHEELS.ABOUT HALF THE REPORTS INVOLVE VEHICLES BUILT WITH THE REMEDY WHEEL USED FOR RECALL 03V279, AND MOST OF THE REMAINING VEHICLES WERE SUBJECT TO THE RECALL.THE PROCESS OF IDENTIFYING PERTINENT FORD COMPLAINTS IS MADE DIFFICULT BY FORD?S PRIOR RECALL AND WARRANTY PROGRAM ACTIVITIES.THE MANUFACTURER COMPLAINT AND WARRANTY COUNTS, WHICH PRIMARILY INVOLVE FAILURES OF RECALL 03V279 REMEDY WHEELS, ARE BASED ON ANALYSIS CONDUCTED TO DATE AND ARE CONSIDERED TO BE CONSERVATIVE.FURTHER INVESTIGATION IS REQUIRED, THUS ODI IS UPGRADING THIS INVESTIGATION TO AN ENGINEERING ANALYSIS (EA).DURING THE EA, PERTINENT FAILURE REPORTS AND CONSEQUENCES WILL BE IDENTIFIED AND REVIEWED.ODI AND FORD WILL DISCUSS DETAILS FOR CONDUCTING AN AUDIT ANALYSIS OF FAILED WHEELS REPLACED UNDER THE NEW SA.ADDITIONALLY, ODI IS AWAITING FORD?S LAB ANALYSIS OF TWO WHEELS WHICH WERE THE SUBJECT OF VOQ REPORTS, ONE OF WHICH WAS INVOLVED IN THE NOTED CRASH EVENT.A DETERMINATION WILL BE MADE AS TO WHETHER FORD?S SERVICE ACTION IS SUFFICIENT FOR ADDRESSING ONGOING RIM FRACTURES.

Wheels:rim

DURING A SEPTEMBER 23, 2004 MEETING AND IN SUBSEQUENT DISCUSSIONS IN NOVEMBER, FORD ADVISED THE OFFICE OF DEFECTS INVESTIGATION (ODI) OF THEIR PLANS TO INTRODUCE AN IMPROVED STEEL WHEEL FOR MANUFACTURING AND SERVICE COMPONENT USE ON THE SUBJECT VEHICLES, INDICATING THIS WOULD OCCUR IN DECEMBER 2004.THE NEW WHEEL DESIGN INCORPORATES AN ADDITIONAL MANUFACTURING PROCESS (SHOT PEENING) WHICH LOWERS TENSILE STRESS IN THE SURFACE LAYER OF THE RIM MATERIAL ADJACENT TO THE CIRCUMFERENTIAL WELD. THEORETICALLY THIS SHOULD IMPROVE RIM DURABILITY BY REDUCING FATIGUE CRACK INITIATION SITES.INDICATIONS FROM FORD?S ACCELERATED TESTING METHODS SHOW AN IMPROVEMENT IN THE PERFORMANCE OF THE NEW WHEEL.IN ADDITION TO PRIOR SAFETY RECALL 03V279 AND SERVICE ACTION (SA) 03M03, FORD WILL ANNOUNCE A NEW EXTENDED WARRANTY SA FOR VEHICLES BUILT PRIOR TO DECEMBER 2004 THAT SUFFER RIM FRACTURES IN SERVICE.THE NEW WHEEL DESIGN WILL BE USED AS A REMEDY.FORD ADVISES THAT A SA IS SUFFICIENT FOR ADDRESSING FUTURE WHEEL FAILURES (INCLUDING RECALL 03V279 REMEDY WHEEL FAILURES) BECAUSE: 1) FAILURE RATES ARE LOW BASED ON FORD?S ANALYSIS, AND 2) DRIVER WARNINGS (REPETITIVE SLOW AIR LOSS, AND OR STEERING WHEEL VIBRATION) ALLOW EARLY AND SAFE DETECTION OF CRACKED WHEELS.ODI HAS RECEIVED 25 VEHICLE OWNER QUESTIONNAIRE (VOQ) REPORTS (INVOLVING 22 VEHICLES) WHICH ALLEGE A RIM FRACTURE OF ONE OR MORE STEEL WHEELS.ABOUT HALF THE REPORTS INVOLVE VEHICLES BUILT WITH THE REMEDY WHEEL USED FOR RECALL 03V279, AND MOST OF THE REMAINING VEHICLES WERE SUBJECT TO THE RECALL.THE PROCESS OF IDENTIFYING PERTINENT FORD COMPLAINTS IS MADE DIFFICULT BY FORD?S PRIOR RECALL AND WARRANTY PROGRAM ACTIVITIES.THE MANUFACTURER COMPLAINT AND WARRANTY COUNTS, WHICH PRIMARILY INVOLVE FAILURES OF RECALL 03V279 REMEDY WHEELS, ARE BASED ON ANALYSIS CONDUCTED TO DATE AND ARE CONSIDERED TO BE CONSERVATIVE.FURTHER INVESTIGATION IS REQUIRED, THUS ODI IS UPGRADING THIS INVESTIGATION TO AN ENGINEERING ANALYSIS (EA).DURING THE EA, PERTINENT FAILURE REPORTS AND CONSEQUENCES WILL BE IDENTIFIED AND REVIEWED.ODI AND FORD WILL DISCUSS DETAILS FOR CONDUCTING AN AUDIT ANALYSIS OF FAILED WHEELS REPLACED UNDER THE NEW SA.ADDITIONALLY, ODI IS AWAITING FORD?S LAB ANALYSIS OF TWO WHEELS WHICH WERE THE SUBJECT OF VOQ REPORTS, ONE OF WHICH WAS INVOLVED IN THE NOTED CRASH EVENT.A DETERMINATION WILL BE MADE AS TO WHETHER FORD?S SERVICE ACTION IS SUFFICIENT FOR ADDRESSING ONGOING RIM FRACTURES.