← New search

2022 Ford Bronco

Owner reports · Recalls · Investigations

When problems were reported

Mileage at the reported incident

Limited mileage data: 68 of 374 reports include usable mileage. There isn’t enough coverage to show a useful chart.

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Visibility/wiper. Review the 65 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Engine. Review the 51 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Service Brakes. Review the 40 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

6 crash reports2 fire reports3 injury reports

What owners actually said

374 reports
Mileage unknown · Sep 10, 2026
Fuel/propulsion System

Was driving on highway with cruise control set. Vehicle started slowing down, so pressed on gas pedal and no response from vehicle, had to navigate to shoulder and was unable to drive vehicle. No warning that there was any issue. Vehicle has been at dealership for a month. Low pressure fuel pump failure and no parts are availabl…

Read full complaint

Was driving on highway with cruise control set. Vehicle started slowing down, so pressed on gas pedal and no response from vehicle, had to navigate to shoulder and was unable to drive vehicle. No warning that there was any issue. Vehicle has been at dealership for a month. Low pressure fuel pump failure and no parts are available.

NHTSA ODI #11763513

Mileage unknown · Sep 7, 2026
Power Train

Clutch pedal went to floor and didn't return. The accumulator on part # MB3Z-7A512-A failed and broke apart causing a complete loss of brake fluid in the clutch hydraulic system rendering the clutch completely inoperable.

NHTSA ODI #11762643

Mileage unknown · Sep 6, 2026
Structure

I am writing to formally complain about a serious and increasingly concerning problem with the hardtop on my 2022 Ford Bronce four-door. I began noticing cracks in the hardtop after becoming aware of numerous complaints from other Bronco owners regarding similar cracking problems. Once I knew what to look for, I inspected my Br…

Read full complaint

I am writing to formally complain about a serious and increasingly concerning problem with the hardtop on my 2022 Ford Bronce four-door. I began noticing cracks in the hardtop after becoming aware of numerous complaints from other Bronco owners regarding similar cracking problems. Once I knew what to look for, I inspected my Bronco and noticed cracks in the hardtop. I promptly brought the issue to the attention of my Ford dealership. Unfortunately, I was told that the vehicle had just passed the time limit of the factory warranty, even though it was well within the mileage limit of the warranty. I find it extremely frustrating that Ford’s position appears to be based on the calendar expiration of the warranty when this is a known problem (defect) that has been reported by numerous Bronco owners. More importantly, the condition of the hardtop has deteriorated significantly. Over the past several months, the cracks have become substantially worse, and I am now concerned that the hardtop could eventually fail completely. This is no longer simply a cosmetic concern. I purchased a new Ford Bronco with the expectation that the vehicle’s major structural components would remain reliable under normal use. I am requesting that Ford reconsider my case and provide full replacement of the defective hardtop at no cost to me, including parts and installation cost. I would also like Ford to consider the safety implications of allowing a hardtop with progressively worsening cracks to remain in service. I have legitimate concerns that the hardtop could fail at speed or during an accident creating hazard or injury.

NHTSA ODI #11762457

Mileage unknown · Sep 4, 2026
Fuel/propulsion System

Simply filing a complaint for the recall on the fuel pump that still has not been remedied over a year ago. I’m hearing stories of people having to replace their fuel pumps and ford not covering it even though it’s an open recall. Hoping to get more pressure on them to get a remedy. Thank you for all you do!

NHTSA ODI #11762209

Mileage unknown · Sep 3, 2026
Seats

Headrest on rear passenger side will not stay up.

NHTSA ODI #11761959

Mileage unknown · Aug 29, 2026
Electrical SystemFuel/propulsion SystemSeats

3 different incidents have came up with recalls that have been going on for awhile this a working vehicle that makes my money to pay for the loans, which for over a year have not made me any money costing me to lose money out of my own pocket, ford has not been willing to work with because it’s a used vehicle and I didn’t barrow…

Read full complaint

3 different incidents have came up with recalls that have been going on for awhile this a working vehicle that makes my money to pay for the loans, which for over a year have not made me any money costing me to lose money out of my own pocket, ford has not been willing to work with because it’s a used vehicle and I didn’t barrow money from to purchase this has been going on for more than a year it is ridiculous!!

NHTSA ODI #11760648

Mileage unknown · Aug 29, 2026
SuspensionWheels

On August 26, 2026, my 2022 Ford Bronco experienced a serious safety related failure while I was driving. The vehicle displayed a sway bar disconnect system warning and became disabled, leaving me stranded on the side of the road. The Bronco had to be towed to a Ford dealership, where it is available for inspection. Ford previo…

Read full complaint

On August 26, 2026, my 2022 Ford Bronco experienced a serious safety related failure while I was driving. The vehicle displayed a sway bar disconnect system warning and became disabled, leaving me stranded on the side of the road. The Bronco had to be towed to a Ford dealership, where it is available for inspection. Ford previously claimed that it inspected my Bronco under a recall specifically pertaining to the sway bar system. Ford determined that the sway bar did not need to be replaced and closed the recall as completed. The vehicle has now experienced a failure involving the same system that Ford claims it previously inspected. I am concerned that the recall inspection may not have identified the problem or that the recall procedure or remedy was insufficient. The precise cause of the current failure is still being diagnosed. Approximately one and a half weeks before the incident, five replacement tires were installed by a mobile tire service. The replacement tires were the same type and size already used on the vehicle. There was no change in tire size and no tire related modification to the Bronco. Three lug nuts were also found loose following this incident. Approximately three months earlier, three lug nuts had come completely off the vehicle. Loose lug nuts were found again during a tire rotation approximately one month before this incident. I do not yet know whether the repeated loose lug nuts and the sway bar system failure are connected. This failure occurred while the vehicle was being driven, disabled the vehicle, and left me stranded. I am requesting that NHTSA document and investigate whether the sway bar recall inspection or remedy was inadequate, or whether another safety defect exists in my 2022 Ford Bronco.

NHTSA ODI #11760585

Mileage unknown · Aug 26, 2026
Unknown Or OtherVisibility/wiper

Windshield is leaking water/rain inside vehicle. I have it at All American Ford Old Bridge,NJ, for 15 days now and they want to charge me portion $256.76 plus tax. BUt, the Bronco has recall 222c12 or 25C52. I was willing to pay not knowing that there as a recall but they said if it breaks or cracks or chips while doing work t…

Read full complaint

Windshield is leaking water/rain inside vehicle. I have it at All American Ford Old Bridge,NJ, for 15 days now and they want to charge me portion $256.76 plus tax. BUt, the Bronco has recall 222c12 or 25C52. I was willing to pay not knowing that there as a recall but they said if it breaks or cracks or chips while doing work they are not responsible to cover new windshield. please advise. They show on Ford recall website the recall complete, but my windshield was never removed, resealed and reinstalled. So that is a lie/fraud on All American Ford part. Please help. I have 2 other major issues with Bronco as well which are recalls that they made me pay for or did not resolve as of yet. I already paid for a middle roof panel and now front passenger roof panel must be replaced (recall 26S32) and they say it is not part of recall. And, the safety concern is the car just turned off on major highway 2 different episods one in May on NJ Turnpike I was almost hit from behind and the other was on Route 35 in Seaside Park, NJ in August. Same dealership said they can't experience it so they cannot diagnose and repair it. It is the fuel pump/loss of power issue #26V236000. the car has to be restarted and there is no warning. I am very worried about this.

NHTSA ODI #11759852

Mileage unknown · Aug 21, 2026
Structure

Fender flares (2) have detached. Flare 1: Passenger side, front wheel - it flew off while driving. Flare 2: Partially breaking / cracking off - on the drivers side, back wheel.

NHTSA ODI #11758670

Mileage unknown · Aug 20, 2026
Electrical SystemEngineFuel System, Gasoline

The contact owns a 2022 Ford Bronco. The contact received notifications of NHTSA Campaign Numbers: 25V455000 (FUEL SYSTEM, GASOLINE) and 26V468000 (ENGINE, ELECTRICAL SYSTEM); however, the parts to do the recall repairs were not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded …

Read full complaint

The contact owns a 2022 Ford Bronco. The contact received notifications of NHTSA Campaign Numbers: 25V455000 (FUEL SYSTEM, GASOLINE) and 26V468000 (ENGINE, ELECTRICAL SYSTEM); however, the parts to do the recall repairs were not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact had not experienced a failure.

NHTSA ODI #11758189

Official recalls

23

26V468000 · Electrical System:wiring:front Underhood; Engine

Jul 20, 2026

Ford Motor Company (Ford) is recalling certain 2021-2026 Bronco and Bronco Raptor vehicles. The engine compartment wiring harness may become damaged and short circuit.

Consequence & remedy

Consequence: A short circuit in the engine compartment can create heat or spark, increasing the risk of a fire.

Remedy: Dealers will install sheathing over the wiring, free of charge. This is a Phased campaign. Phase 1 will include 2026 Bronco Raptor notified owners on 7/31/2026. Phase 2 will include 2021-2025 Bronco Raptor vehicle will notify owners on or about 8/14/2026. Phase 3 will include 2021-2026 Bronco will notify owners on or about 9/1/2026. Owner notification letters were mailed August 5, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S55. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on July 23, 2026.

Additional source detail variants (2)

Engine

Ford Motor Company (Ford) is recalling certain 2021-2026 Bronco and Bronco Raptor vehicles. The engine compartment wiring harness may become damaged and short circuit.

Consequence: A short circuit in the engine compartment can create heat or spark, increasing the risk of a fire.

Remedy: Dealers will install sheathing over the wiring, free of charge. This is a Phased campaign. Phase 1 will include 2026 Bronco Raptor notified owners on 7/31/2026. Phase 2 will include 2021-2025 Bronco Raptor vehicle will notify owners on or about 8/14/2026. Phase 3 will include 2021-2026 Bronco will notify owners on or about 9/1/2026. Owner notification letters were mailed August 5, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S55. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on July 23, 2026.

Electrical System:wiring:front Underhood

Ford Motor Company (Ford) is recalling certain 2021-2026 Bronco and Bronco Raptor vehicles. The engine compartment wiring harness may become damaged and short circuit.

Consequence: A short circuit in the engine compartment can create heat or spark, increasing the risk of a fire.

Remedy: Dealers will install sheathing over the wiring, free of charge. This is a Phased campaign. Phase 1 will include 2026 Bronco Raptor notified owners on 7/31/2026. Phase 2 will include 2021-2025 Bronco Raptor vehicle will notify owners on or about 8/14/2026. Phase 3 will include 2021-2026 Bronco will notify owners on or about 9/1/2026. Owner notification letters were mailed August 5, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S55. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on July 23, 2026.

26V403000 · Structure:body

Jun 24, 2026

Ford Motor Company (Ford) is recalling certain 2022-2026 Bronco vehicles. The fender flares may not be properly secured and detach from the vehicle.

Consequence & remedy

Consequence: A detached fender flare can become a road hazard and increase the risk of a crash.

Remedy: Dealers will inspect and repair, or replace the fender flares as necessary, free of charge. Owner notification letters were mailed September 1, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S47. Vehicle Identification Numbers (VINs) involved in this recall will be searchable on NHTSA.gov beginning August 7, 2026.

26V299000 · Structure:body:roof And Pillars

May 12, 2026

Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles. The 3-door and 5-door Molded-In-Color (MIC) hardtop roof panels may have been manufactured improperly, which can allow sections of the outer roof panel to separate and detach from the vehicle.

Consequence & remedy

Consequence: A detached section of roof can create a road hazard, increasing the risk of a crash.

Remedy: Dealers will inspect and replace the hard top as necessary, free of charge. Interim letters, notifying owners of the safety risk were mailed May 28, 2026. Additional letters will be sent once the remedy is available, anticipated in November 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S32. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on May 12, 2026.

26V236000 · Power Train:automatic Transmission

Apr 14, 2026

Ford Motor Company (Ford) is recalling certain 2021-2025 Bronco vehicles. The transmission to transfer case joint may be misaligned due to an incorrectly performed previous repair, which could lead to wear of the transmission output shaft splines and transfer case input splines.

Consequence & remedy

Consequence: Excessive wear of the transmission and transfer case splines may result in a loss of drive power or vehicle rollaway, increasing the risk of a crash.

Remedy: Dealers will inspect the transmission to transfer case joint and replace the transmission and transfer case as necessary, free of charge. Owner notification letters were mailed July 9, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S26. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on April 15, 2026.

26V124000 · Back Over Prevention:software

Mar 3, 2026

Ford Motor Company (Ford) is recalling certain 2021-2026 Ford Bronco and 2021-2024 Ford Edge vehicles. The Accessory Protocol Interface Module (APIM) may overheat and shutdown, which can prevent the rearview camera image from displaying as intended.

Consequence & remedy

Consequence: A rearview camera that fails to display an image can reduce the driver’s view behind the vehicle, increasing the risk of a crash.

Remedy: The APIM software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed April 13, 2026. Owners may contact Ford Customer Service at 1-866-436-7332. Ford's number for this recall is 26S09. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on March 5, 2026.

25V888000 · Back Over Prevention: Sensing System: Camera

Dec 18, 2025

Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles equipped with 8-inch SYNC infotainment screens that were previously repaired incorrectly under recall number 23V165. The rearview camera image may still be displayed after a backing event has ended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rear Visibility."

Consequence & remedy

Consequence: A rearview image that continues to be displayed after the vehicle is shifted out of reverse may distract the driver, increasing the risk of a crash.

Remedy: Dealer will update the SYNC module software ,free of charge. Owner notification letters were mailed January 28, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25C72. Vehicle Identification Numbers (VINs) involved in this recall will be searchable on NHTSA.gov beginning January 30, 2026.

25V721000 · Seats:critical Fasteners

Oct 23, 2025

Ford Motor Company (Ford) is recalling certain 2021-2023 Bronco vehicles. The front seats may have a loose or dislodged seat frame height-adjust pivot bolt.

Consequence & remedy

Consequence: A seat with a dislodged bolt may not properly restrain an occupant in a crash, increasing the risk of injury.

Remedy: Dealers will inspect and replace the pivot links and bolts as necessary, free of charge. Owner notification letters were mailed April 28, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25SB5. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov beginning October 28, 2025.

25V685000 · Equipment:electrical:engine Block Heater

Oct 10, 2025

Ford Motor Company (Ford) is recalling certain 2016-2019 Lincoln MKC, 2016-2023 Explorer, 2019-2020 Fusion, 2019-2024 Ranger, 2020-2022 Lincoln Corsair, Escape, 2021-2024 Bronco, Bronco Sport, and 2022-2024 Maverick vehicles. The engine block heater may crack and develop a coolant leak, causing it to short circuit when the block heater is plugged in.

Consequence & remedy

Consequence: An electrical short circuit can increase the risk of a fire.

Remedy: Owners are advised not to plug in their block heater until the vehicle is remedied. Dealers will replace the block heater, free of charge. Owners will also have a alternative option to replace engine block heater element with a threaded blanking plug, and remove the block heater electrical cord. Interim letters, notifying owners of the safety risk, were mailed December 3, 2025. Additional letters will be sent once the final remedy is available, anticipated September 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25SA4. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on October 15, 2025.

25V455000 · Fuel System, Gasoline:delivery:fuel Pump

Jul 7, 2025

Ford Motor Company (Ford) is recalling certain 2021-2023 Bronco, Explorer, Lincoln Aviator, F-250 SD, F-350 SD, F-450 SD, F-550 SD, 2021-2022 Lincoln Navigator, Mustang, F-150, and 2022 Expedition vehicles. The low-pressure fuel pump may fail, which can result in an engine stall while driving.

Consequence & remedy

Consequence: An engine stall increases the risk of a crash.

Remedy: Dealers will replace the low pressure fuel pump on super duty vehicles and update the powertrain control module (PCM) software on all other affected vehicles, free of charge. Owner notification letters were mailed July 27, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S75.

25V273000 · Back Over Prevention: Sensing System: Camera

May 14, 2025

Ford Motor Company (Ford) is recalling certain 2022-2023 Bronco vehicles. The 360-degree view camera may not display a rearview image when the vehicle is placed in reverse.

Consequence & remedy

Consequence: Loss of the rearview camera image can reduce the driver's view of what is behind the vehicle, increasing the risk of a crash.

Remedy: Dealers will replace the rearview camera, free of charge. Owner notification letters were mailed October 8, 2025. Owners may contact Ford Customer Service at 1-866-436-7332. Ford's number for this recall is 23S48. This recall expands previous recall number 23V-598.

25V312000 · Back Over Prevention: Sensing System: Camera

May 9, 2025

Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles equipped with 8-inch SYNC infotainment screens that were repaired incorrectly under recall 22V-825. The rearview camera image may still be displayed after a backing event has ended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rear Visibility."

Consequence & remedy

Consequence: A rearview image that continues to be displayed after the vehicle is shifted out of reverse may distract the driver, increasing the risk of a crash.

Remedy: Dealers will update SYNC module software, free of charge. Owner notification letters were mailed June 18, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25C14.

25V315000 · Back Over Prevention:software

May 9, 2025

Ford Motor Company (Ford) is recalling certain 2021-2024 Bronco, F-150, 2021-2024 Edge, 2022-2025 Escape, F-250, F-350, F-450, F-550, F-600, 2022-2024 Expedition, 2022-2025 Transit, 2021-2023 Mach-E, 2024 Ranger, Mustang, 2021-2023 Lincoln Nautilus, 2022-2024 Navigator, and 2023-2024 Corsair vehicles. A software error may cause the rearview camera image to delay, freeze, or not display when the vehicle is in reverse.

Consequence & remedy

Consequence: A frozen or missing rearview camera image can reduce the driver's view behind the vehicle, increasing the risk of a crash.

Remedy: The accessory protocol interface module (APIM) software will be updated by a dealer or through an over-the-air update, free of charge. This will be a phased campaign, with the remedy becoming available in different phases based on model and model years. Interim letters notifying owners of the safety risk were mailed on June 26, 2025. Additional letters will be mailed once the final remedy is available on each phase. Owner notification letters were sent on October 8, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S49.

25V025000 · Suspension:rear:shock Absorber

Jan 17, 2025

Ford Motor Company (Ford) is recalling certain 2021-2024 Bronco vehicles. The rear shock absorbers may corrode and fail, resulting in detachment of the external reservoir.

Consequence & remedy

Consequence: An external reservoir that detaches from a vehicle can create a road hazard, increasing the risk of a crash.

Remedy: Dealers will replace the rear shock absorbers, as necessary free of charge. Owner notification letters were mailed August 15, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S01.

24V635000 · Engine And Engine Cooling:engine:hard Parts Internal/mechanical

Aug 23, 2024

Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco, F-150, Edge, Explorer, Lincoln Nautilus, and Lincoln Aviator vehicles equipped with either a 2.7L or 3.0L Nano EcoBoost engine. The engine intake valves may break while driving, which can result in engine failure and a loss of drive power.

Consequence & remedy

Consequence: A loss of drive power increases the risk of a crash.

Remedy: Dealers will perform an engine cycle test and replace the engine as necessary, free of charge. Owner notification letters were mailed July 3, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 24S55.

23V379000 · Equipment:other:labels

May 26, 2023

Ford Motor Company (Ford) is recalling certain 2022-2023 Bronco, 2023 Super Duty F-250, and 2019-2023 Ranger vehicles. The Tire and Loading Information (TREAD) label states the incorrect load carrying capacity, which can result in an overloaded vehicle. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 110, "Tire Selection and Rims."

Consequence & remedy

Consequence: An overloaded vehicle increases the risk of a crash.

Remedy: Ford will mail a new TREAD label to install over the existing label, free of charge. Owners will also have the option to take their vehicle to a Ford or Lincoln dealer to have the new label installed, free of charge. Owner notification letters were mailed July 21, 2023. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23C18.

23V358000 · Seat Belts:critical Fasteners

May 18, 2023

Ford Motor Company (Ford) is recalling certain 2021-2023 Bronco vehicles built with the 5-Door body style. The first-row seat belt latch plates may be difficult to access from their stowed position. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 208, "Occupant Crash Protection."

Consequence & remedy

Consequence: Difficulty accessing the seat belt latches may result in occupants not wearing their seat belts, increasing the risk of injury in a crash.

Remedy: Dealers will add a sliding clip latch stop to the driver and front passenger seat belts, free of charge. Interim owner notification letters notifying owners of the safety risk were mailed July 14, 2023. Owner letters informing owners that parts are available were mailed on October 2, 2023. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23C16.

23V165000 · Back Over Prevention: Sensing System: Camera

Mar 10, 2023

Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles equipped with 8-inch SYNC infotainment screens that were previously remedied under recall 22V-825. The rearview camera image may still be displayed after a backing event has ended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rear Visibility."

Consequence & remedy

Consequence: A rearview image that continues to be displayed after the vehicle is shifted out of reverse may distract the driver, increasing the risk of a crash.

Remedy: The SYNC module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed on March 28, 2024. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23C05.

23V155000 · Steering

Mar 8, 2023

Ford Motor Company (Ford) is recalling certain 2023 Bronco Wildtrak and 2022 Bronco Raptor vehicles. Internal damage to the steering gear may require increased steering effort or cause the steering wheel to lock-up.

Consequence & remedy

Consequence: A steering wheel that locks-up can result in a complete loss of steering control, increasing the risk of a crash.

Remedy: Owners are advised not to drive their vehicles until the remedy is performed. Dealers will replace the steering gear, free of charge. Owner notification letters were mailed March 31, 2023. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23S09.

23V070000 · Power Train:automatic Transmission

Feb 10, 2023

Ford Motor Company (Ford) is recalling certain 2022-2023 F-150, Mustang, Explorer, Bronco, and 2023 Lincoln Aviator vehicles equipped with automatic transmissions. The transmission may contain a loose bolt which could prevent the transmission from engaging the park gear, although the gear shifter position may indicate that the vehicle has been shifted to "PARK."

Consequence & remedy

Consequence: The inability to secure the vehicle in the park position can result in a rollaway, increasing the risk of a crash or injury.

Remedy: Dealers will inspect and, if necessary, replace the transmissions, free of charge. Owner notification letters were mailed April 25, 2023. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23S06.

22V928000 · Air Bags:sensor:side Impact

Dec 14, 2022

Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles. The right or left side impact sensors may not be properly secured to the vehicle.

Consequence & remedy

Consequence: An improperly secured side impact sensor may cause the air bags to unintentionally deploy, or not to deploy as intended, increasing the risk of injury in a crash.

Remedy: Dealers will inspect the side impact sensor attachments and repair, as necessary, free of charge. Owner notification letters were mailed January 20, 2023. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22S77.

22V825000 · Back Over Prevention: Sensing System: Camera

Nov 3, 2022

Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles equipped with rearview camera systems and 8-inch screen displays. The rearview camera image may still be displayed after a backing event has ended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rear Visibility."

Consequence & remedy

Consequence: A rearview image that continues to be displayed after the vehicle is shifted out of reverse may distract the driver, increasing the risk of a crash.

Remedy: The SYNC module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed on March 25, 2024. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22C27.

22V451000 · Visibility:windshield

Jun 24, 2022

Ford Motor Company (Ford) is recalling certain 2022 Bronco and Ranger vehicles. The windshield may not have been properly bonded to the vehicle, which could allow it to detach during a crash. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 212, "Windshield Mounting."

Consequence & remedy

Consequence: A windshield that separates from a vehicle during a crash can increase the risk of injury.

Remedy: Dealers will remove and reinstall the windshield, free of charge. Owner notification letters were mailed July 18, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22C12.

22V411000 · Latches/locks/linkages:doors:lock

Jun 10, 2022

Ford Motor Company (Ford) is recalling certain four-door 2021-2022 Bronco vehicles. The passenger-side rear door may be opened from inside of the vehicle when the child safety lock is in the "ON" position.

Consequence & remedy

Consequence: A malfunctioning child safety lock increases the risk of injury to a child occupant.

Remedy: Dealers will inspect the passenger-side child safety locks door child safety lock and latch, and replace them, if necessary, free of charge. Owner notification letters were mailed June 28, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22S44.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

2

PE24019 · Low-pressure Fuel Pump Failure

Opened Jul 29, 2024 · Closed Sep 19, 2025

Status: closed (inferred from source dates) · Fuel System, Gasoline:delivery:fuel Pump

On July 29, 2024, the Office of Defects Investigation (ODI) opened PE24019 to investigate complaints of low-pressure fuel pump failures in MY 2021 Ford Bronco vehicles. Some consumers reported that the failure occurred without warning while driving, resulting in a complete loss of motive power with no ability to restart the engine. Ford determined that several other vehicle models contain low-pressure fuel pumps substantially similar to the 2021 Ford Bronco, including the 2022-2023 Ford Bronco, 2018-2023 Ford F-150, 2022-2023 Ford Expedition, 2019-2023 Lincoln Navigator, 2020-2023 Ford F-250-F-550, 2024 Ford Super Duty Chassis Cab, 2024-2025 Ford Ranger, 2020-2023 Ford Explorer, 2020-2023 Lincoln Aviator, and 2021-2025 Ford Mustang. ODI's investigation found that the affected vehicles may lose fuel pressure and flow from the fuel delivery module (consisting of a low-pressure fuel pump, jet pump, reservoir, and other parts) due to a low-pressure pump failure. This can cause the engine to stall while driving. The root cause is reduced internal clearance in the fuel pump, increasing friction and sensitivity to vapor lock. Fuel blockage from contamination inside the jet pump also contributed to the failure. Ford stated that the contamination source was unknown. On July 7, 2025, Ford filed recall 25V-455 for certain 2021-2023 Ford F-550 SD/F-450 SD/F-350 SD/F-250 SD, 2021-2022 Lincoln Navigator, 2021-2022 Ford Mustang, 2021-2022 Ford F-150, 2021-2023 Ford Explorer, 2022 Ford Expedition, and 2021-2023 Ford Bronco vehicles produced between July 1, 2021, and July 30, 2022. The recall also included certain 2021-2023 Lincoln Aviator produced between July 1, 2021, and December 21, 2022. Ford explained in its recall filingthat the production dates used for the recall were based on changes in the manufacturing process. Specifically, Ford determined that in June 2021, the supplier modified the jet pump manufacturing process, producing fuel pump chambers with a lower-than-specified internal clearance. In July 2022, the supplier implemented corrective actions to the manufacturing process by adding two additional vacuum pumps to reduce contamination during the production of the jet pump. ODI has identified approximately 1,000 reports involving vehicles covered in this investigation but excluded from recall 25V-455. However, even with such reports, these vehicles experienced comparatively lower failure rates than the vehicles that are subject to Recall 25V-455. Ford has explained that these vehicles were excluded from the recall population because they did not experience the manufacturing changes that prompted the recall. Specifically, according to Ford, vehicles built before July 1, 2021 (the recall production start date), were not affected by the supplier’s change to the jet pump manufacturing process. Even after closing this investigation, ODI will continue to monitor complaints for vehicles excluded from recall 25V-455 to consider whether they exhibit the same risks as the vehicles encompassed by the recall. The recall remedy is currently under development. In view of Ford’s recall action, ODI is closing this Preliminary Evaluation, but will continue to monitor the issue as a remedy is developed and implemented. ODI will take additional action if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.

EA23002 · Loss Of Motive Power

Opened Sep 29, 2023 · Closed Oct 31, 2024

Status: closed (inferred from source dates) · Engine

On July 22, 2022, the Office of Defects Investigation (ODI) granted a Defect Petition (DP22001) and opened a Preliminary Evaluation (PE22007) to investigate allegations of loss of motive power in model year (MY) 2021 Ford Bronco vehicles equipped with 2.7L EcoBoost engines. Complainants were reporting sudden engine failure while driving resulting in a loss of motive power, often without the ability to restart. During PE22007, the cause of engine failure and loss of motive power in the subject vehicles was determined to be intake valve fracture, and the full scope of vehicles affected by the subject defect was identified as all MY 2021-2022 Ford and Lincoln models equipped with either the 2.7L or 3.0L EcoBoost engines, referred to as the “Nano” engine family.  If an intake valve fractures in the subject engines, it may drop into the cylinder and contact the piston, often resulting in catastrophic engine damage. On September 29, 2023, PE22007 was upgraded to an Engineering Analysis (EA23002) to further investigate the subject defect across the full scope of affected vehicles. During EA23002, ODI visited Ford facilities to review technical information related to intake valve fracture in “Nano” engines, coordinated with NHTSA’s Vehicle Research and Testing Center (VRTC), and analyzed updated field data relating the subject defect. Forensic analysis of fractured intake valves demonstrated that the defective components exhibited “grinding burn” or out of specification hardness in the area of the keeper grooves. The presence of grinding burn is evidence that during the groove grinding phase of production, the temperature of the valve became sufficiently high to alter the microstructure of the material and is indicative that the valve supplier’s manufacturing processes were not within control specifications. Grinding burn results in a hard, brittle microstructure and high residual stresses toward the surface of the valve. Through normal engine loading, a valve with grinding burn will likely fracture at the area of highest vulnerability, which is the third keeper groove. In its response to the EA23002 Information Request (IR) letter, Ford provided evidence of 396 customer complaints (including field reports), 825 warranty claims, and 936 engine exchanges. When considering both ODI and manufacturer failure report data, there have been reports representing 1066 unique vehicles within the subject vehicle population. Analysis of the failure report data demonstrates that vehicles equipped with potentially defective intake valves were built within a production “spike period” of May 2021 – October 2021. The beginning of the spike period corresponds to a ramp up in production at the valve supplier manufacturing facility, and the end of the spike period aligns with the implementation of several mid-production process improvements and the decision to change the metal alloy used to produce intake valves from “Silchrome Lite” to “Silchrome 1”. Ford began investigating the subject defect in July 2021, determined the root cause, and took corrective measures for the new production vehicles. Analysis of the failure report data demonstrates that these corrective actions were successful in eliminating the risk of intake valve fracture for subject vehicles produced after October 2021. However, Ford did not take any field action to address vehicles produced during the spike period, and in the several months following the implementation of the production changes, a significant number of field failures continued to occur. It is Ford’s assessment that not all valves produced during the spike period are defective, and that failures associated with the subject defect occur at low time in service. Analysis of the failure report data demonstrates that the vast majority of failures have occurred before 20,000 miles with over half of all reported failures occurring before 5,000 miles. The rate of reported failures related to the subject defect has steadily decreased since November 2021. ODI coordinated with NHTSA’s National Center for Statistics and Analysis (NCSA) to conduct statistical analysis and predict the number of future failures associated with the subject defect. The results of this analysis, and the trends identified through the failure report data are generally consistent with Ford’s assessment that defective intake valves will likely fail at a low time in service and indicate that the majority of subject vehicles equipped with defective valves have already experienced a failure. On August 23, 2024, Ford submitted recall 24V635 for subject vehicles equipped with “Nano” engines and built within the production spike period identified above (total population 90,736 vehicles). The remedy includes an inspection at a Ford/Lincoln dealership where the lifetime engine cycles of the vehicle will be determined. If a vehicle does not meet a threshold for lifetime engine cycles, the dealership will conduct a high RPM engine cycle accumulation procedure, which aims to identify if the vehicle is equipped with defective intake valves. Any vehicle that fails the accumulation procedure will receive an engine replacement under the recall. In addition to recall 24V635, Ford has stated that it will launch customer satisfaction campaign 24N12, which will provide extended warranty coverage to the subject vehicles through the earlier of 10 years or 150,000 miles. In view of the recall action being taken by Ford, ODI is closing this Engineering Analysis. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.