IllustrationClutch pedal went to floor and didn't return. The accumulator on part # MB3Z-7A512-A failed and broke apart causing a complete loss of brake fluid in the clutch hydraulic system rendering the clutch completely inoperable.
2022 Ford Bronco
Owner reports · Recalls · Investigations
Limited comparison data
There is not enough comparable history to draw a useful model-year comparison.
About this comparison →How this year compares
Owner complaints by model year
Compare all Bronco years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
Limited mileage data: 68 of 374 reports include usable mileage. There isn’t enough coverage to show a useful chart.
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Visibility/wiper. Review the 65 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 51 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Service Brakes. Review the 40 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
6 crash reports2 fire reports3 injury reports
Power Train complaints
39 reports2022 Ford Bronco 2.7L EcoBoost VIN [XXX] has experienced recurring engine oil pressure failure causing vehicle to enter limp mode limiting speed to 25mph creating an unsafe driving condition. Diagnostic trouble codes P0524 Engine Oil Pressure Too Low and P06DD Engine Oil Pressure Control Stuck Off confirmed. Two failed warranty …
Read full complaint
2022 Ford Bronco 2.7L EcoBoost VIN [XXX] has experienced recurring engine oil pressure failure causing vehicle to enter limp mode limiting speed to 25mph creating an unsafe driving condition. Diagnostic trouble codes P0524 Engine Oil Pressure Too Low and P06DD Engine Oil Pressure Control Stuck Off confirmed. Two failed warranty repair attempts at Lenoir City Ford Lenoir City TN on XXX and XXX. Dealership provided loaner vehicle both times acknowledging vehicle was unsafe to drive. Ford corporate case number XXC is open. Third repair attempt scheduled XXX.” INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
The Incident: While operating the vehicle under high load, the driver received an explicit "Service Engine Soon" powertrain malfunction alert stating: "The powertrain control module lost communication with the vehicle active grill shutter module for a period of time." Immediately following this warning, the engine experienced a …
Read full complaint
The Incident: While operating the vehicle under high load, the driver received an explicit "Service Engine Soon" powertrain malfunction alert stating: "The powertrain control module lost communication with the vehicle active grill shutter module for a period of time." Immediately following this warning, the engine experienced a severe loss of power, followed by loud metallic banging from the engine bay. The vehicle stalled completely and lost all motive power, creating an imminent highway safety hazard.The Physical Damage: Subsequent mechanical teardown by the dealership revealed terminal block destruction, including deep vertical cylinder wall scoring, heavy unburnt liquid gasoline residue in the engine oil pan, and a blown head gasket.Relationship to Active Safety Defect: This catastrophic engine failure mirrors the progressive failure profile of NHTSA Campaign 25V455 / Ford Safety Recall 25S75 (Low-Pressure Fuel Pump Failure). In this EcoBoost architecture, the Active Grill Shutter (AGS) module shares critical voltage paths, grounding blocks, and wiring looms with the engine management and fuel delivery systems. The sudden network communication loss is diagnostic proof of a severe voltage drop or electrical short caused by the high-friction fuel pump degradation detailed in Recall 25S75. This circuit failure instantly starved the engine of fuel under turbo boost, inducing an extreme lean-out condition. The resulting pre-ignition forces violently shattered the internal piston rings (the loud banging), which then gouged the cylinder walls, wiped out compression, fouled the crankcase with fuel residue, and blew the head gasket.Request for Action: Ford's current VIN parameters for Recall 25S75 have not yet captured my specific vehicle despite it matching the exact production window, component setup, and catastrophic failure sequence. I am requesting that the NHTSA log this case as definitive evidence of consequential engine destruction originating from the 25V455 fue
While operating the vehicle under load, the vehicle suffered a sudden and severe loss of engine performance, followed immediately by loud metallic banging from the engine bay. The vehicle lost all power and was immediately disabled (LIMP MODE), presenting an imminent highway safety hazard.The Physical Damage: Subsequent mechanic…
Read full complaint
While operating the vehicle under load, the vehicle suffered a sudden and severe loss of engine performance, followed immediately by loud metallic banging from the engine bay. The vehicle lost all power and was immediately disabled (LIMP MODE), presenting an imminent highway safety hazard.The Physical Damage: Subsequent mechanical teardown revealed deep vertical cylinder wall scoring, heavy raw fuel residue in the engine oil pan, and a blown head gasket. Relationship to Active Safety Defect: This catastrophic block failure perfectly mirrors the progressive failure profile of NHTSA Campaign 25V455 / Ford Safety Recall 25S75 (Low-Pressure Fuel Pump Failure). Internal component degradation in the fuel tank delivery module dropped fuel pressure to the engine. Under turbo boost, this starvation induced an extreme, instantaneous lean-out condition. The resulting low-speed pre-ignition (LSPI) exploded and shattered the internal piston rings (the metallic banging), leading to mechanical wall gouging, unburnt fuel wash into the lower crankcase, and a secondary blown head gasket. Request for Action: Ford's current VIN parameters for Recall 25S75 have not yet captured my specific vehicle despite it matching the exact production window, component setup, and catastrophic failure sequence. I am requesting that the NHTSA log this case as clear evidence of consequential engine destruction originating from the 25V455 pump defect, and evaluate whether Ford's recall scope must be expanded to protect other consumers from highway engine failures.
Differential carrier replacement due to metal contmination being found in differential during oil change and a transmission overhaul due to excessive wear of(clutch container, CDF bushing, forward hub and front support bushings). They also noted a sticking valve in the main control on my 2022 Ford Bronco 2.7L V6 when taken in to…
Read full complaint
Differential carrier replacement due to metal contmination being found in differential during oil change and a transmission overhaul due to excessive wear of(clutch container, CDF bushing, forward hub and front support bushings). They also noted a sticking valve in the main control on my 2022 Ford Bronco 2.7L V6 when taken in to dealership to evaluate vehichle under warranty due to ongoing intermittent thump/clunking noise when coming to a stop and accelerating from a stop as well as when backing up from a stop and while driving as well, intermittent loud metal slapping sound at speeds over 60 mph, intermittent jerking of vehichle when cycling through gears, unexpected downshift at high speeds. After differential replacement and transmission overhaul due to excessive wear while under warranty, my vehichle continues to experience the same symptoms and problems and feel this is a safety issue.
I believe my vehicle has suffered a cracked/fractured or broken intake valve on cylinder number 4. There is very low compression in that cylinder. I checked it and it only managed to produce 25psi. I inspected the cylinder with a borescope camera and there is no damage or excessive wear to the piston or cylinder bore. They both …
Read full complaint
I believe my vehicle has suffered a cracked/fractured or broken intake valve on cylinder number 4. There is very low compression in that cylinder. I checked it and it only managed to produce 25psi. I inspected the cylinder with a borescope camera and there is no damage or excessive wear to the piston or cylinder bore. They both look pristine with no signs of anything. I could not see either the intake or exhaust valves on my camera. They are the only pieces of the engine I could not inspect that could possible cause a compression issue. It is my understanding that ford is aware of an issue of this happening on some 2.7 Ecoboost engines?
I’ve complained to my local Ford dealer about 10-speed transmission issues including to several different service techs. There is a loud clunk and physical movement of the vehicle when shifting from park through to reverse and eventually to drive—it’s the P to R which is most noticeable. I’ve had 3rd party mechanics inspect the …
Read full complaint
I’ve complained to my local Ford dealer about 10-speed transmission issues including to several different service techs. There is a loud clunk and physical movement of the vehicle when shifting from park through to reverse and eventually to drive—it’s the P to R which is most noticeable. I’ve had 3rd party mechanics inspect the clunk, had Ford replace the driveshaft, conducted a trans fluid flush, but the clunk persists. I am concerned that one day, the vehicle will not shift out of park or potentially damage the transmission to an undriveable state outside of warranty. This has persisted for several years. I need Ford to replace the transmission and then conduct research into the issues with the old one once removed.
I have experienced a loss of fuel pressure/engine stall on several occasions. I am not sure of the specific dates yet I had to add one on this form. There has been a recall since July 2025, for which Ford has acknowledged this increases the risk of a crash yet there is still no resolution. This is unacceptable, I have listed the…
Read full complaint
I have experienced a loss of fuel pressure/engine stall on several occasions. I am not sure of the specific dates yet I had to add one on this form. There has been a recall since July 2025, for which Ford has acknowledged this increases the risk of a crash yet there is still no resolution. This is unacceptable, I have listed the recall numbers below. Manufacturer Recall Number 25S75 NHTSA Recall Number 25V455
Good afternoon! My car started having issues going in reverse before I received the recall notification. It would nearly stall out and happened a couple times prior to getting the notice. Once I got the notice, I reached out to the dealer to see if anything could be done and was told no, not yet. Now, months later, it has gotte…
Read full complaint
Good afternoon! My car started having issues going in reverse before I received the recall notification. It would nearly stall out and happened a couple times prior to getting the notice. Once I got the notice, I reached out to the dealer to see if anything could be done and was told no, not yet. Now, months later, it has gotten so bad that I am having to leave my house when it's cool (it doesn't stall as bad when it's cool out), and park my car in a certain way each day to ensure that I can effectively leave work without my car stalling. What is worse is that now, on hot days, my car semi-stalls, when I am driving on toll roads or back country roads on the way home. It loses power or jerks. I have an hour commute each way and this is NOT okay. Frankly, it is very scary sometimes. I have reached out to the dealership to ask them if it's safe for me to drive my car or if there is something they could do and I am constantly told that there is no solution, I have to wait, and they "legally" cannot tell me that it is safe to drive my car. They offered the option to rent a car, but I would have to pay a minimum of $45 out of pocket, per DAY, and I cannot afford to do that! I am already paying $600 a month for this car, now they want me to pay an additional $1350-$1395 a month just so I can feel safe? This has been going on for roughly 7 months. Who knows how long a "solution" will take. 7 months x $1350 a month = I would be out almost $9500 on TOP OF my car payment with no end in sight. I feel like this is moving at a snails pace. The problem is getting worse and I am getting the run around. No help is being offered to make me feel safe driving this car! They seem annoyed when I ask about it (I have only reached out three times in the last 4 months). The recall even says that it could stall while driving. So, honestly, what is it going to take for me to not die in a crash when my car stops on a high-speed road? Seriously. What can be done?
RECALL REMEDY NOT AVAILABLE. Causing safety concerns while driving.
Official recalls
2326V468000 · Electrical System:wiring:front Underhood; Engine
Jul 20, 2026
Ford Motor Company (Ford) is recalling certain 2021-2026 Bronco and Bronco Raptor vehicles. The engine compartment wiring harness may become damaged and short circuit.
Consequence & remedy
Consequence: A short circuit in the engine compartment can create heat or spark, increasing the risk of a fire.
Remedy: Dealers will install sheathing over the wiring, free of charge. This is a Phased campaign. Phase 1 will include 2026 Bronco Raptor notified owners on 7/31/2026. Phase 2 will include 2021-2025 Bronco Raptor vehicle will notify owners on or about 8/14/2026. Phase 3 will include 2021-2026 Bronco will notify owners on or about 9/1/2026. Owner notification letters were mailed August 5, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S55. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on July 23, 2026.
Additional source detail variants (2)
Engine
Ford Motor Company (Ford) is recalling certain 2021-2026 Bronco and Bronco Raptor vehicles. The engine compartment wiring harness may become damaged and short circuit.
Consequence: A short circuit in the engine compartment can create heat or spark, increasing the risk of a fire.
Remedy: Dealers will install sheathing over the wiring, free of charge. This is a Phased campaign. Phase 1 will include 2026 Bronco Raptor notified owners on 7/31/2026. Phase 2 will include 2021-2025 Bronco Raptor vehicle will notify owners on or about 8/14/2026. Phase 3 will include 2021-2026 Bronco will notify owners on or about 9/1/2026. Owner notification letters were mailed August 5, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S55. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on July 23, 2026.
Electrical System:wiring:front Underhood
Ford Motor Company (Ford) is recalling certain 2021-2026 Bronco and Bronco Raptor vehicles. The engine compartment wiring harness may become damaged and short circuit.
Consequence: A short circuit in the engine compartment can create heat or spark, increasing the risk of a fire.
Remedy: Dealers will install sheathing over the wiring, free of charge. This is a Phased campaign. Phase 1 will include 2026 Bronco Raptor notified owners on 7/31/2026. Phase 2 will include 2021-2025 Bronco Raptor vehicle will notify owners on or about 8/14/2026. Phase 3 will include 2021-2026 Bronco will notify owners on or about 9/1/2026. Owner notification letters were mailed August 5, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S55. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on July 23, 2026.
26V403000 · Structure:body
Jun 24, 2026
Ford Motor Company (Ford) is recalling certain 2022-2026 Bronco vehicles. The fender flares may not be properly secured and detach from the vehicle.
Consequence & remedy
Consequence: A detached fender flare can become a road hazard and increase the risk of a crash.
Remedy: Dealers will inspect and repair, or replace the fender flares as necessary, free of charge. Owner notification letters were mailed September 1, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S47. Vehicle Identification Numbers (VINs) involved in this recall will be searchable on NHTSA.gov beginning August 7, 2026.
26V299000 · Structure:body:roof And Pillars
May 12, 2026
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles. The 3-door and 5-door Molded-In-Color (MIC) hardtop roof panels may have been manufactured improperly, which can allow sections of the outer roof panel to separate and detach from the vehicle.
Consequence & remedy
Consequence: A detached section of roof can create a road hazard, increasing the risk of a crash.
Remedy: Dealers will inspect and replace the hard top as necessary, free of charge. Interim letters, notifying owners of the safety risk were mailed May 28, 2026. Additional letters will be sent once the remedy is available, anticipated in November 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S32. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on May 12, 2026.
26V236000 · Power Train:automatic Transmission
Apr 14, 2026
Ford Motor Company (Ford) is recalling certain 2021-2025 Bronco vehicles. The transmission to transfer case joint may be misaligned due to an incorrectly performed previous repair, which could lead to wear of the transmission output shaft splines and transfer case input splines.
Consequence & remedy
Consequence: Excessive wear of the transmission and transfer case splines may result in a loss of drive power or vehicle rollaway, increasing the risk of a crash.
Remedy: Dealers will inspect the transmission to transfer case joint and replace the transmission and transfer case as necessary, free of charge. Owner notification letters were mailed July 9, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S26. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on April 15, 2026.
26V124000 · Back Over Prevention:software
Mar 3, 2026
Ford Motor Company (Ford) is recalling certain 2021-2026 Ford Bronco and 2021-2024 Ford Edge vehicles. The Accessory Protocol Interface Module (APIM) may overheat and shutdown, which can prevent the rearview camera image from displaying as intended.
Consequence & remedy
Consequence: A rearview camera that fails to display an image can reduce the driver’s view behind the vehicle, increasing the risk of a crash.
Remedy: The APIM software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed April 13, 2026. Owners may contact Ford Customer Service at 1-866-436-7332. Ford's number for this recall is 26S09. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on March 5, 2026.
25V888000 · Back Over Prevention: Sensing System: Camera
Dec 18, 2025
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles equipped with 8-inch SYNC infotainment screens that were previously repaired incorrectly under recall number 23V165. The rearview camera image may still be displayed after a backing event has ended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rear Visibility."
Consequence & remedy
Consequence: A rearview image that continues to be displayed after the vehicle is shifted out of reverse may distract the driver, increasing the risk of a crash.
Remedy: Dealer will update the SYNC module software ,free of charge. Owner notification letters were mailed January 28, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25C72. Vehicle Identification Numbers (VINs) involved in this recall will be searchable on NHTSA.gov beginning January 30, 2026.
25V721000 · Seats:critical Fasteners
Oct 23, 2025
Ford Motor Company (Ford) is recalling certain 2021-2023 Bronco vehicles. The front seats may have a loose or dislodged seat frame height-adjust pivot bolt.
Consequence & remedy
Consequence: A seat with a dislodged bolt may not properly restrain an occupant in a crash, increasing the risk of injury.
Remedy: Dealers will inspect and replace the pivot links and bolts as necessary, free of charge. Owner notification letters were mailed April 28, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25SB5. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov beginning October 28, 2025.
25V685000 · Equipment:electrical:engine Block Heater
Oct 10, 2025
Ford Motor Company (Ford) is recalling certain 2016-2019 Lincoln MKC, 2016-2023 Explorer, 2019-2020 Fusion, 2019-2024 Ranger, 2020-2022 Lincoln Corsair, Escape, 2021-2024 Bronco, Bronco Sport, and 2022-2024 Maverick vehicles. The engine block heater may crack and develop a coolant leak, causing it to short circuit when the block heater is plugged in.
Consequence & remedy
Consequence: An electrical short circuit can increase the risk of a fire.
Remedy: Owners are advised not to plug in their block heater until the vehicle is remedied. Dealers will replace the block heater, free of charge. Owners will also have a alternative option to replace engine block heater element with a threaded blanking plug, and remove the block heater electrical cord. Interim letters, notifying owners of the safety risk, were mailed December 3, 2025. Additional letters will be sent once the final remedy is available, anticipated September 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25SA4. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on October 15, 2025.
25V455000 · Fuel System, Gasoline:delivery:fuel Pump
Jul 7, 2025
Ford Motor Company (Ford) is recalling certain 2021-2023 Bronco, Explorer, Lincoln Aviator, F-250 SD, F-350 SD, F-450 SD, F-550 SD, 2021-2022 Lincoln Navigator, Mustang, F-150, and 2022 Expedition vehicles. The low-pressure fuel pump may fail, which can result in an engine stall while driving.
Consequence & remedy
Consequence: An engine stall increases the risk of a crash.
Remedy: Dealers will replace the low pressure fuel pump on super duty vehicles and update the powertrain control module (PCM) software on all other affected vehicles, free of charge. Owner notification letters were mailed July 27, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S75.
25V273000 · Back Over Prevention: Sensing System: Camera
May 14, 2025
Ford Motor Company (Ford) is recalling certain 2022-2023 Bronco vehicles. The 360-degree view camera may not display a rearview image when the vehicle is placed in reverse.
Consequence & remedy
Consequence: Loss of the rearview camera image can reduce the driver's view of what is behind the vehicle, increasing the risk of a crash.
Remedy: Dealers will replace the rearview camera, free of charge. Owner notification letters were mailed October 8, 2025. Owners may contact Ford Customer Service at 1-866-436-7332. Ford's number for this recall is 23S48. This recall expands previous recall number 23V-598.
25V312000 · Back Over Prevention: Sensing System: Camera
May 9, 2025
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles equipped with 8-inch SYNC infotainment screens that were repaired incorrectly under recall 22V-825. The rearview camera image may still be displayed after a backing event has ended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rear Visibility."
Consequence & remedy
Consequence: A rearview image that continues to be displayed after the vehicle is shifted out of reverse may distract the driver, increasing the risk of a crash.
Remedy: Dealers will update SYNC module software, free of charge. Owner notification letters were mailed June 18, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25C14.
25V315000 · Back Over Prevention:software
May 9, 2025
Ford Motor Company (Ford) is recalling certain 2021-2024 Bronco, F-150, 2021-2024 Edge, 2022-2025 Escape, F-250, F-350, F-450, F-550, F-600, 2022-2024 Expedition, 2022-2025 Transit, 2021-2023 Mach-E, 2024 Ranger, Mustang, 2021-2023 Lincoln Nautilus, 2022-2024 Navigator, and 2023-2024 Corsair vehicles. A software error may cause the rearview camera image to delay, freeze, or not display when the vehicle is in reverse.
Consequence & remedy
Consequence: A frozen or missing rearview camera image can reduce the driver's view behind the vehicle, increasing the risk of a crash.
Remedy: The accessory protocol interface module (APIM) software will be updated by a dealer or through an over-the-air update, free of charge. This will be a phased campaign, with the remedy becoming available in different phases based on model and model years. Interim letters notifying owners of the safety risk were mailed on June 26, 2025. Additional letters will be mailed once the final remedy is available on each phase. Owner notification letters were sent on October 8, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S49.
25V025000 · Suspension:rear:shock Absorber
Jan 17, 2025
Ford Motor Company (Ford) is recalling certain 2021-2024 Bronco vehicles. The rear shock absorbers may corrode and fail, resulting in detachment of the external reservoir.
Consequence & remedy
Consequence: An external reservoir that detaches from a vehicle can create a road hazard, increasing the risk of a crash.
Remedy: Dealers will replace the rear shock absorbers, as necessary free of charge. Owner notification letters were mailed August 15, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S01.
24V635000 · Engine And Engine Cooling:engine:hard Parts Internal/mechanical
Aug 23, 2024
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco, F-150, Edge, Explorer, Lincoln Nautilus, and Lincoln Aviator vehicles equipped with either a 2.7L or 3.0L Nano EcoBoost engine. The engine intake valves may break while driving, which can result in engine failure and a loss of drive power.
Consequence & remedy
Consequence: A loss of drive power increases the risk of a crash.
Remedy: Dealers will perform an engine cycle test and replace the engine as necessary, free of charge. Owner notification letters were mailed July 3, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 24S55.
23V379000 · Equipment:other:labels
May 26, 2023
Ford Motor Company (Ford) is recalling certain 2022-2023 Bronco, 2023 Super Duty F-250, and 2019-2023 Ranger vehicles. The Tire and Loading Information (TREAD) label states the incorrect load carrying capacity, which can result in an overloaded vehicle. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 110, "Tire Selection and Rims."
Consequence & remedy
Consequence: An overloaded vehicle increases the risk of a crash.
Remedy: Ford will mail a new TREAD label to install over the existing label, free of charge. Owners will also have the option to take their vehicle to a Ford or Lincoln dealer to have the new label installed, free of charge. Owner notification letters were mailed July 21, 2023. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23C18.
23V358000 · Seat Belts:critical Fasteners
May 18, 2023
Ford Motor Company (Ford) is recalling certain 2021-2023 Bronco vehicles built with the 5-Door body style. The first-row seat belt latch plates may be difficult to access from their stowed position. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 208, "Occupant Crash Protection."
Consequence & remedy
Consequence: Difficulty accessing the seat belt latches may result in occupants not wearing their seat belts, increasing the risk of injury in a crash.
Remedy: Dealers will add a sliding clip latch stop to the driver and front passenger seat belts, free of charge. Interim owner notification letters notifying owners of the safety risk were mailed July 14, 2023. Owner letters informing owners that parts are available were mailed on October 2, 2023. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23C16.
23V165000 · Back Over Prevention: Sensing System: Camera
Mar 10, 2023
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles equipped with 8-inch SYNC infotainment screens that were previously remedied under recall 22V-825. The rearview camera image may still be displayed after a backing event has ended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rear Visibility."
Consequence & remedy
Consequence: A rearview image that continues to be displayed after the vehicle is shifted out of reverse may distract the driver, increasing the risk of a crash.
Remedy: The SYNC module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed on March 28, 2024. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23C05.
23V155000 · Steering
Mar 8, 2023
Ford Motor Company (Ford) is recalling certain 2023 Bronco Wildtrak and 2022 Bronco Raptor vehicles. Internal damage to the steering gear may require increased steering effort or cause the steering wheel to lock-up.
Consequence & remedy
Consequence: A steering wheel that locks-up can result in a complete loss of steering control, increasing the risk of a crash.
Remedy: Owners are advised not to drive their vehicles until the remedy is performed. Dealers will replace the steering gear, free of charge. Owner notification letters were mailed March 31, 2023. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23S09.
23V070000 · Power Train:automatic Transmission
Feb 10, 2023
Ford Motor Company (Ford) is recalling certain 2022-2023 F-150, Mustang, Explorer, Bronco, and 2023 Lincoln Aviator vehicles equipped with automatic transmissions. The transmission may contain a loose bolt which could prevent the transmission from engaging the park gear, although the gear shifter position may indicate that the vehicle has been shifted to "PARK."
Consequence & remedy
Consequence: The inability to secure the vehicle in the park position can result in a rollaway, increasing the risk of a crash or injury.
Remedy: Dealers will inspect and, if necessary, replace the transmissions, free of charge. Owner notification letters were mailed April 25, 2023. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23S06.
22V928000 · Air Bags:sensor:side Impact
Dec 14, 2022
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles. The right or left side impact sensors may not be properly secured to the vehicle.
Consequence & remedy
Consequence: An improperly secured side impact sensor may cause the air bags to unintentionally deploy, or not to deploy as intended, increasing the risk of injury in a crash.
Remedy: Dealers will inspect the side impact sensor attachments and repair, as necessary, free of charge. Owner notification letters were mailed January 20, 2023. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22S77.
22V825000 · Back Over Prevention: Sensing System: Camera
Nov 3, 2022
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles equipped with rearview camera systems and 8-inch screen displays. The rearview camera image may still be displayed after a backing event has ended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rear Visibility."
Consequence & remedy
Consequence: A rearview image that continues to be displayed after the vehicle is shifted out of reverse may distract the driver, increasing the risk of a crash.
Remedy: The SYNC module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed on March 25, 2024. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22C27.
22V451000 · Visibility:windshield
Jun 24, 2022
Ford Motor Company (Ford) is recalling certain 2022 Bronco and Ranger vehicles. The windshield may not have been properly bonded to the vehicle, which could allow it to detach during a crash. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 212, "Windshield Mounting."
Consequence & remedy
Consequence: A windshield that separates from a vehicle during a crash can increase the risk of injury.
Remedy: Dealers will remove and reinstall the windshield, free of charge. Owner notification letters were mailed July 18, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22C12.
22V411000 · Latches/locks/linkages:doors:lock
Jun 10, 2022
Ford Motor Company (Ford) is recalling certain four-door 2021-2022 Bronco vehicles. The passenger-side rear door may be opened from inside of the vehicle when the child safety lock is in the "ON" position.
Consequence & remedy
Consequence: A malfunctioning child safety lock increases the risk of injury to a child occupant.
Remedy: Dealers will inspect the passenger-side child safety locks door child safety lock and latch, and replace them, if necessary, free of charge. Owner notification letters were mailed June 28, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22S44.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2PE24019 · Low-pressure Fuel Pump Failure
Opened Jul 29, 2024 · Closed Sep 19, 2025
Status: closed (inferred from source dates) · Fuel System, Gasoline:delivery:fuel Pump
On July 29, 2024, the Office of Defects Investigation (ODI) opened PE24019 to investigate complaints of low-pressure fuel pump failures in MY 2021 Ford Bronco vehicles. Some consumers reported that the failure occurred without warning while driving, resulting in a complete loss of motive power with no ability to restart the engine. Ford determined that several other vehicle models contain low-pressure fuel pumps substantially similar to the 2021 Ford Bronco, including the 2022-2023 Ford Bronco, 2018-2023 Ford F-150, 2022-2023 Ford Expedition, 2019-2023 Lincoln Navigator, 2020-2023 Ford F-250-F-550, 2024 Ford Super Duty Chassis Cab, 2024-2025 Ford Ranger, 2020-2023 Ford Explorer, 2020-2023 Lincoln Aviator, and 2021-2025 Ford Mustang. ODI's investigation found that the affected vehicles may lose fuel pressure and flow from the fuel delivery module (consisting of a low-pressure fuel pump, jet pump, reservoir, and other parts) due to a low-pressure pump failure. This can cause the engine to stall while driving. The root cause is reduced internal clearance in the fuel pump, increasing friction and sensitivity to vapor lock. Fuel blockage from contamination inside the jet pump also contributed to the failure. Ford stated that the contamination source was unknown. On July 7, 2025, Ford filed recall 25V-455 for certain 2021-2023 Ford F-550 SD/F-450 SD/F-350 SD/F-250 SD, 2021-2022 Lincoln Navigator, 2021-2022 Ford Mustang, 2021-2022 Ford F-150, 2021-2023 Ford Explorer, 2022 Ford Expedition, and 2021-2023 Ford Bronco vehicles produced between July 1, 2021, and July 30, 2022. The recall also included certain 2021-2023 Lincoln Aviator produced between July 1, 2021, and December 21, 2022. Ford explained in its recall filingthat the production dates used for the recall were based on changes in the manufacturing process. Specifically, Ford determined that in June 2021, the supplier modified the jet pump manufacturing process, producing fuel pump chambers with a lower-than-specified internal clearance. In July 2022, the supplier implemented corrective actions to the manufacturing process by adding two additional vacuum pumps to reduce contamination during the production of the jet pump. ODI has identified approximately 1,000 reports involving vehicles covered in this investigation but excluded from recall 25V-455. However, even with such reports, these vehicles experienced comparatively lower failure rates than the vehicles that are subject to Recall 25V-455. Ford has explained that these vehicles were excluded from the recall population because they did not experience the manufacturing changes that prompted the recall. Specifically, according to Ford, vehicles built before July 1, 2021 (the recall production start date), were not affected by the supplier’s change to the jet pump manufacturing process. Even after closing this investigation, ODI will continue to monitor complaints for vehicles excluded from recall 25V-455 to consider whether they exhibit the same risks as the vehicles encompassed by the recall. The recall remedy is currently under development. In view of Ford’s recall action, ODI is closing this Preliminary Evaluation, but will continue to monitor the issue as a remedy is developed and implemented. ODI will take additional action if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
EA23002 · Loss Of Motive Power
Opened Sep 29, 2023 · Closed Oct 31, 2024
Status: closed (inferred from source dates) · Engine
On July 22, 2022, the Office of Defects Investigation (ODI) granted a Defect Petition (DP22001) and opened a Preliminary Evaluation (PE22007) to investigate allegations of loss of motive power in model year (MY) 2021 Ford Bronco vehicles equipped with 2.7L EcoBoost engines. Complainants were reporting sudden engine failure while driving resulting in a loss of motive power, often without the ability to restart. During PE22007, the cause of engine failure and loss of motive power in the subject vehicles was determined to be intake valve fracture, and the full scope of vehicles affected by the subject defect was identified as all MY 2021-2022 Ford and Lincoln models equipped with either the 2.7L or 3.0L EcoBoost engines, referred to as the “Nano” engine family. If an intake valve fractures in the subject engines, it may drop into the cylinder and contact the piston, often resulting in catastrophic engine damage. On September 29, 2023, PE22007 was upgraded to an Engineering Analysis (EA23002) to further investigate the subject defect across the full scope of affected vehicles. During EA23002, ODI visited Ford facilities to review technical information related to intake valve fracture in “Nano” engines, coordinated with NHTSA’s Vehicle Research and Testing Center (VRTC), and analyzed updated field data relating the subject defect. Forensic analysis of fractured intake valves demonstrated that the defective components exhibited “grinding burn” or out of specification hardness in the area of the keeper grooves. The presence of grinding burn is evidence that during the groove grinding phase of production, the temperature of the valve became sufficiently high to alter the microstructure of the material and is indicative that the valve supplier’s manufacturing processes were not within control specifications. Grinding burn results in a hard, brittle microstructure and high residual stresses toward the surface of the valve. Through normal engine loading, a valve with grinding burn will likely fracture at the area of highest vulnerability, which is the third keeper groove. In its response to the EA23002 Information Request (IR) letter, Ford provided evidence of 396 customer complaints (including field reports), 825 warranty claims, and 936 engine exchanges. When considering both ODI and manufacturer failure report data, there have been reports representing 1066 unique vehicles within the subject vehicle population. Analysis of the failure report data demonstrates that vehicles equipped with potentially defective intake valves were built within a production “spike period” of May 2021 – October 2021. The beginning of the spike period corresponds to a ramp up in production at the valve supplier manufacturing facility, and the end of the spike period aligns with the implementation of several mid-production process improvements and the decision to change the metal alloy used to produce intake valves from “Silchrome Lite” to “Silchrome 1”. Ford began investigating the subject defect in July 2021, determined the root cause, and took corrective measures for the new production vehicles. Analysis of the failure report data demonstrates that these corrective actions were successful in eliminating the risk of intake valve fracture for subject vehicles produced after October 2021. However, Ford did not take any field action to address vehicles produced during the spike period, and in the several months following the implementation of the production changes, a significant number of field failures continued to occur. It is Ford’s assessment that not all valves produced during the spike period are defective, and that failures associated with the subject defect occur at low time in service. Analysis of the failure report data demonstrates that the vast majority of failures have occurred before 20,000 miles with over half of all reported failures occurring before 5,000 miles. The rate of reported failures related to the subject defect has steadily decreased since November 2021. ODI coordinated with NHTSA’s National Center for Statistics and Analysis (NCSA) to conduct statistical analysis and predict the number of future failures associated with the subject defect. The results of this analysis, and the trends identified through the failure report data are generally consistent with Ford’s assessment that defective intake valves will likely fail at a low time in service and indicate that the majority of subject vehicles equipped with defective valves have already experienced a failure. On August 23, 2024, Ford submitted recall 24V635 for subject vehicles equipped with “Nano” engines and built within the production spike period identified above (total population 90,736 vehicles). The remedy includes an inspection at a Ford/Lincoln dealership where the lifetime engine cycles of the vehicle will be determined. If a vehicle does not meet a threshold for lifetime engine cycles, the dealership will conduct a high RPM engine cycle accumulation procedure, which aims to identify if the vehicle is equipped with defective intake valves. Any vehicle that fails the accumulation procedure will receive an engine replacement under the recall. In addition to recall 24V635, Ford has stated that it will launch customer satisfaction campaign 24N12, which will provide extended warranty coverage to the subject vehicles through the earlier of 10 years or 150,000 miles. In view of the recall action being taken by Ford, ODI is closing this Engineering Analysis. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.