IllustrationRpm Royalty a rental car company located at [XXX] has been renting out a rebuilt 488 Ferrari with no functional airbags. This is a serious safety risk INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
2016 Ferrari 488 Gtb
Owner reports · Recalls · Investigations
Limited comparison data
There is not enough comparable history to draw a useful model-year comparison.
About this comparison →How this year compares
Owner complaints by model year
Compare all 488 Gtb years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
Limited mileage data: 0 of 2 reports include usable mileage. There isn’t enough coverage to show a useful chart.
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Air Bags. Review the 2 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
0 crash reports0 fire reports0 injury reports
Air Bags complaints
2 reportsTL* TAKATA RECALL. THE CONTACT OWNS A 2016 FERRARI 488 GTB. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 19V006000 (AIR BAGS). THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. FERRARI BEVERLY HILLS (9372 WILSHIRE BLVD, BEVERLY HILLS, CA 90212) WAS CONTACTED AND C…
Read full complaint
TL* TAKATA RECALL. THE CONTACT OWNS A 2016 FERRARI 488 GTB. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 19V006000 (AIR BAGS). THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. FERRARI BEVERLY HILLS (9372 WILSHIRE BLVD, BEVERLY HILLS, CA 90212) WAS CONTACTED AND CONFIRMED THAT THE PARTS WERE NOT AVAILABLE FOR THE RECALL REMEDY. THE MANUFACTURER WAS NOT NOTIFIED. THE CONTACT WAS CONCERNED AND WAS INFORMED BY THE DEALER TO CALL BACK IN SIX MONTHS FOR PART AVAILABILITY. THE CONTACT HAD NOT EXPERIENCED A FAILURE. PARTS DISTRIBUTION DISCONNECT.
Official recalls
521V833000 · Service Brakes, Hydraulic
Oct 23, 2021
Ferrari North America, Inc. (Ferrari) is recalling certain 2010-2015 458 Italia, 2012-2015 458 Spider, 2014-2015 458 Speciale, 2015 458 Speciale Aperta, 2016-2019 488 GTB, and 488 Spider vehicles. The brake system may leak brake fluid, resulting in a loss of braking ability.
Consequence & remedy
Consequence: Loss of braking ability increases the risk of a crash.
Remedy: Dealers will replace the brake fluid reservoir cap and update the software, at no charge. Owner notification letters were mailed on March 4, 2022. Owners may contact Ferrari customer service at 1-201-816-2668. Ferrari's number for this recall is 78.
19V411000 · Air Bags; Air Bags: Air Bag/restraint Control Module
Jun 4, 2019
Ferrari North America, Inc. (Ferrari) is recalling certain 2018 488 Spider, 488 Pista, 2015 458 Speciale A, 2016-2018 488 GTB, 2015-2017 F12 Berlinetta, 2016 F12 tdf, and 2016-2018 Carlifornia T vehicles. The air bag Electronic Control Unit (ECU) may malfunction, possibly causing the non-deployment or improper deployment of the air bags and/or seat belt pretensioners.
Consequence & remedy
Consequence: In the event of a crash, air bags and/or seat belt pretensioners that do not deploy as intended can increase the risk of injury.
Remedy: Ferrari will notify owners, and dealers will replace the air bag ECU, free of charge. The recall began August 2, 2019. Owners may contact Ferrari customer service at 1-201-816-2668. Ferrari's number for this recall is 70.
Additional source detail variants (2)
Air Bags: Air Bag/restraint Control Module
Ferrari North America, Inc. (Ferrari) is recalling certain 2018 488 Spider, 488 Pista, 2015 458 Speciale A, 2016-2018 488 GTB, 2015-2017 F12 Berlinetta, 2016 F12 tdf, and 2016-2018 Carlifornia T vehicles. The air bag Electronic Control Unit (ECU) may malfunction, possibly causing the non-deployment or improper deployment of the air bags and/or seat belt pretensioners.
Consequence: In the event of a crash, air bags and/or seat belt pretensioners that do not deploy as intended can increase the risk of injury.
Remedy: Ferrari will notify owners, and dealers will replace the air bag ECU, free of charge. The recall began August 2, 2019. Owners may contact Ferrari customer service at 1-201-816-2668. Ferrari's number for this recall is 70.
Air Bags
Ferrari North America, Inc. (Ferrari) is recalling certain 2018 488 Spider, 488 Pista, 2015 458 Speciale A, 2016-2018 488 GTB, 2015-2017 F12 Berlinetta, 2016 F12 tdf, and 2016-2018 Carlifornia T vehicles. The air bag Electronic Control Unit (ECU) may malfunction, possibly causing the non-deployment or improper deployment of the air bags and/or seat belt pretensioners.
Consequence: In the event of a crash, air bags and/or seat belt pretensioners that do not deploy as intended can increase the risk of injury.
Remedy: Ferrari will notify owners, and dealers will replace the air bag ECU, free of charge. The recall began August 2, 2019. Owners may contact Ferrari customer service at 1-201-816-2668. Ferrari's number for this recall is 70.
19V006000 · Air Bags:frontal:passenger Side:inflator Module
Jan 9, 2019
Ferrari North America (Ferrari) is recalling certain 2014 Ferrari California, 2014-2015 Ferrari 458 Italia, 458 Spider, 2014-2016 Ferrari FF, 2014-2017 Ferrari F12, 2015-2018 Ferrari California T, 2015 Ferrari 458 Speciale A, 2016 Ferrari F60 America, 2016-2017 Ferrari F12 tdf, 2016-2018 Ferrari 488 GTB, 488 Spider, 2017-2018 Ferrari GTC4Lusso and 2018 GTC4Lusso T vehicles nationwide. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Ferrari will notify owners, and dealers will replace the passenger frontal air bag assembly, free of charge. The recall began March 8, 2019. Owners may contact Ferrari customer service at 1-866-551-2828. Ferrari's number for this recall is 65.
18V164000 · Electrical System:software; Service Brakes, Hydraulic:foundation Components:disc
Mar 9, 2018
Ferrari North America, Inc. (Ferrari) is recalling certain 2016 488 GTB and 488 Spider vehicles. Due to a software error, the driver may not be warned that the brake discs are critically worn.
Consequence & remedy
Consequence: If the driver is not warned about the critical disc wear, brake disc damage may result, increasing the risk of a crash.
Remedy: Ferrari will notify owners, and dealers will update the instrument panel node software, free of charge. Owners may contact Ferrari customer service at 1-201-816-2668. Ferrari's number for this recall is 64.
Additional source detail variants (2)
Electrical System:software
Ferrari North America, Inc. (Ferrari) is recalling certain 2016 488 GTB and 488 Spider vehicles. Due to a software error, the driver may not be warned that the brake discs are critically worn.
Consequence: If the driver is not warned about the critical disc wear, brake disc damage may result, increasing the risk of a crash.
Remedy: Ferrari will notify owners, and dealers will update the instrument panel node software, free of charge. Owners may contact Ferrari customer service at 1-201-816-2668. Ferrari's number for this recall is 64.
Service Brakes, Hydraulic:foundation Components:disc
Ferrari North America, Inc. (Ferrari) is recalling certain 2016 488 GTB and 488 Spider vehicles. Due to a software error, the driver may not be warned that the brake discs are critically worn.
Consequence: If the driver is not warned about the critical disc wear, brake disc damage may result, increasing the risk of a crash.
Remedy: Ferrari will notify owners, and dealers will update the instrument panel node software, free of charge. Owners may contact Ferrari customer service at 1-201-816-2668. Ferrari's number for this recall is 64.
15V881000 · Fuel System, Gasoline:delivery:hoses, Lines/piping, And Fittings
Dec 28, 2015
Ferrari North America (FNA) is recalling certain model year 2016 488 GTB vehicles manufactured September 9, 2015, to November 6, 2015. The affected vehicles may be equipped with a low pressure fuel line connection that was not properly coated during manufacturing. This may cause a fuel vapor leak during engine start.
Consequence & remedy
Consequence: A fuel vapor leak during engine start increases the risk of a fire.
Remedy: Ferrari will replace the low pressure fuel line assembly connection, free of charge. Affected vehicles are located in dealer inventory and will be remedied before customer retail. The recall began on December 18, 2015. Owners may contact FNA customer service at 1-866-551-2828.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.