IllustrationTURBO CHARGER RESONATOR FAILED X 2 VEHICLE TO GO NO FASTER THAN 30 MPH . THIS ON A SUPER HIGHWAY IS VERY DANGEROUS. *TR
2006 Dodge Sprinter 2500
Owner reports · Recalls · Investigations
Limited comparison data
There is not enough comparable history to draw a useful model-year comparison.
About this comparison →How this year compares
Owner complaints by model year
Compare all Sprinter 2500 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
150–25K
925–50K
350–75K
075–100K
1100–150K
1150K+
29 reports with mileage · 5 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Engine And Engine Cooling. Review the 13 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Power Train. Review the 7 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 3 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
1 crash reports1 fire reports1 injury reports
Fuel System, Other complaints
1 reportsOfficial recalls
516V833000 · Electrical System: Instrument Cluster/panel; Service Brakes, Hydraulic
Nov 17, 2016
Daimler Vans USA, LLC (DVUSA) is recalling certain model year 2003-2006 Dodge and Freightliner Sprinter 2500 and 3500 vans manufactured June 30, 2003, to August 31, 2006. The instrument cluster on the affected vehicles fails to illuminate the BRAKE warning lamp in the instrument cluster during the vehicle start up bulb-function check. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 105, "Hydraulic and Electric Brake Systems."
Consequence & remedy
Consequence: Without the BRAKE lamp illuminating during the vehicle start up bulb-function check, the driver has no confirmation that the lamp is working and therefore may not know whether or not the lamp will illuminate if the brake fluid level is low. If the operator is unaware that the vehicle has low brake fluid, there would be an increased risk of a crash.
Remedy: DVUSA will notify owners, and DVUSA and Dodge dealers will correct the instrument cluster software, as necessary, free of charge. An interim notification was sent to owners on January 6, 2017. A second notice will be mailed to owners once the remedy becomes available. The recall began on July 27, 2017. Owners may contact DVUSA customer service at 1-770-705-2070.
Additional source detail variants (2)
Electrical System: Instrument Cluster/panel
Daimler Vans USA, LLC (DVUSA) is recalling certain model year 2003-2006 Dodge and Freightliner Sprinter 2500 and 3500 vans manufactured June 30, 2003, to August 31, 2006. The instrument cluster on the affected vehicles fails to illuminate the BRAKE warning lamp in the instrument cluster during the vehicle start up bulb-function check. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 105, "Hydraulic and Electric Brake Systems."
Consequence: Without the BRAKE lamp illuminating during the vehicle start up bulb-function check, the driver has no confirmation that the lamp is working and therefore may not know whether or not the lamp will illuminate if the brake fluid level is low. If the operator is unaware that the vehicle has low brake fluid, there would be an increased risk of a crash.
Remedy: DVUSA will notify owners, and DVUSA and Dodge dealers will correct the instrument cluster software, as necessary, free of charge. An interim notification was sent to owners on January 6, 2017. A second notice will be mailed to owners once the remedy becomes available. The recall began on July 27, 2017. Owners may contact DVUSA customer service at 1-770-705-2070.
Service Brakes, Hydraulic
Daimler Vans USA, LLC (DVUSA) is recalling certain model year 2003-2006 Dodge and Freightliner Sprinter 2500 and 3500 vans manufactured June 30, 2003, to August 31, 2006. The instrument cluster on the affected vehicles fails to illuminate the BRAKE warning lamp in the instrument cluster during the vehicle start up bulb-function check. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 105, "Hydraulic and Electric Brake Systems."
Consequence: Without the BRAKE lamp illuminating during the vehicle start up bulb-function check, the driver has no confirmation that the lamp is working and therefore may not know whether or not the lamp will illuminate if the brake fluid level is low. If the operator is unaware that the vehicle has low brake fluid, there would be an increased risk of a crash.
Remedy: DVUSA will notify owners, and DVUSA and Dodge dealers will correct the instrument cluster software, as necessary, free of charge. An interim notification was sent to owners on January 6, 2017. A second notice will be mailed to owners once the remedy becomes available. The recall began on July 27, 2017. Owners may contact DVUSA customer service at 1-770-705-2070.
08V651000 · Equipment Adaptive/mobility
Dec 10, 2008
ILDERTON CONVERSION IS RECALLING 3 MY 2006 SPRINTER DODGE 2500 VANS EQUIPPED WITH RICON PLATFORM STYLE WHEELCHAIR LIFTS. THESE VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 404, "PLATFORM LIFT INSTALLATIONS IN MOTOR VEHICLES." THE THRESHOLD WARNING SYSTEM MAY NOT DETECT THE PRESENCE OF A WHEELCHAIR OR MOBILITY AID USER IN A CERTAIN SPOT WITHIN THE DEFINED THRESHOLD AREA.
Consequence & remedy
Consequence: THE USER OF THE LIFT COULD BE INJURED SHOULD THE LIFT MOVE UNINTENTIONALLY.
Remedy: ILDERTON CONVERSION IS WORKING WITH RICON TO CORRECT THE WHEELCHAIR LIFTS FREE OF CHARGE (PLEASE SEE 07E095). OWNERS MAY CONTACT RICON AT 1-818-267-3000 OR ILDERTON CONVERSION AT 1-800-859-6066.
08V652000 · Equipment Adaptive/mobility
Dec 10, 2008
ILDERTON CONVERSION IS RECALLING 3 MY 2006 DODGE SPRINTER 2500 VANS EQUIPPED WITH RICON PLATFORM STYLE WHEELCHAIR LIFTS. THESE LIFTS FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 403, "PLATFORM LIFT SYSTEM ACCESSIBLE FOR MOTOR VEHICLES." THE ANTI-STOW INTERLOCK MAY NOT DETECT THE PRESENCE OF A WHEELCHAIR OR MOBILITY AID USER. THE PRESSURE SENSING SWITCH THAT DETECTS THE PRESENCE OF WEIGHT ON THE PLATFORM WAS NOT ADJUSTED TO THE NECESSARY SENSITIVITY LEVEL. THE LIFT COULD STOW EVEN THOUGH SOMEONE OR SOMETHING IS STILL ON THE LIFT.
Consequence & remedy
Consequence: A LIFT OCCUPANT CAN BE INJURED SHOULD THE LIFT BEGIN TO STOW UNINTENTIONALLY.
Remedy: ILDERTON CONVERSION IS WORKING WITH RICON TO CORRECT THE WHEELCHAIR LIFTS FREE OF CHARGE (PLEASE SEE 07E097). OWNERS MAY CONTACT RICON AT 1-818-267-3000 OR ILDERTON CONVERSION AT 1-800-859-6066.
08V339000 · Steering:column
Jul 24, 2008
SPRINTER IS RECALLING 10 MY 2001-2006 DODGE AND FREIGHTLINER 2500 AND 3500 VEHICLES. THE WELDING SEAM BETWEEN THE BRACKET AND STEERING COLUMN OF AFFECTED SPARE PARTS DOES NOT MEET DESIGN SPECIFICATIONS. THE RESULT OF AN OUT OF SPECIFICATION WELDING SEAM IS THAT THE STEERING COLUMN MAY DETACH FROM ITS INTERIOR VEHICLE MOUNTING BRACKET.
Consequence & remedy
Consequence: THE OPERATOR MAY LOSE STEERING ABILITY OF THE VEHICLE INCREASING THE RISK OF A CRASH.
Remedy: DEALERS WILL INSPECT AND REPLACE THE STEERING COLUMNS FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN ON OR BEFORE FEBRUARY 16, 2009. OWNERS MAY CONTACT SPRINTER AT 843-695-5057.
07V299000 · Interior Lighting
Jul 13, 2007
ON CERTAIN TRUCKS EQUIPPED WITH REAR AIR CONDITIONING SYSTEM, THE INTERIOR LAMP IS EQUIPPED WITH AN 18W LAMP AND A SCATTERING LENS. IN EXTREMELY HOT AND HUMID CONDITIONS, THE COMBINATION OF HEAT AND HUMIDITY, AND THE HEAT FROM THE LAMP DUE TO EXTREME LONG TERM OPERATION, CAN DISTORT THE SCATTERING LENS.
Consequence & remedy
Consequence: THE SWITCHING CONTACTS OF THE LAMP MAY CAUSE A SHORT CIRCUIT OF THE REAR LAMP INCREASING THE RISK OF A FIRE.
Remedy: DEALERS WILL REPLACE THE REAR INTERIOR LAMPS FREE OF CHARGE WITH A MODIFIED VERSION WHICH IS NOT SUBJECT TO THE IMPACTS OF HEAT AND HUMIDITY. THE RECALL BEGAN ON DECEMBER 17, 2007. OWNERS MAY CONTACT DAIMLERCHRYSLER MANUFACTURING INTERNATIONAL AT 1-843-695-5041.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.