← New search

2008 Dodge RAM 3500

Owner reports · Recalls · Investigations

Similar to other model years

Owner complaints for the 2008 Dodge RAM 3500 do not stand out strongly from the model-year median of 124.5.

About this comparison →

When problems were reported

Mileage at the reported incident

116 reports with mileage · 57 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Steering. Review the 94 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Suspension. Review the 22 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Air Bags. Review the 18 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

9 crash reports14 fire reports4 injury reports

What owners actually said

173 reports
80,000 miles · Nov 19, 2015
Steering

TL* THE CONTACT OWNS A 2008 DODGE RAM 3500. THE CONTACT STATED THAT THE FRONT PASSENGER SIDE WHEEL AND TIRE SEPARATED FROM THE VEHICLE WHILE ENTERING A PARKING AREA. THE VEHICLE WAS TOWED TO AN INDEPENDENT MECHANIC WHO DIAGNOSED THAT THE FRONT PASSENGER SIDE TIE ROD FRACTURED. THE VEHICLE WAS REPAIRED AND THE TIE ROD WAS REPLACE…

Read full complaint

TL* THE CONTACT OWNS A 2008 DODGE RAM 3500. THE CONTACT STATED THAT THE FRONT PASSENGER SIDE WHEEL AND TIRE SEPARATED FROM THE VEHICLE WHILE ENTERING A PARKING AREA. THE VEHICLE WAS TOWED TO AN INDEPENDENT MECHANIC WHO DIAGNOSED THAT THE FRONT PASSENGER SIDE TIE ROD FRACTURED. THE VEHICLE WAS REPAIRED AND THE TIE ROD WAS REPLACED. THE MANUFACTURER WAS CONTACTED. THE APPROXIMATE FAILURE MILEAGE WAS 80,000. UPDATED 04/04/16*LJ THE CONSUMER STATED THE MANUFACTURER CLAIMED ONLY THE LEFT TIE ROD WAS AN ISSUE. UPDATED 04/06/16.

NHTSA ODI #10794859

Mileage unknown · Nov 12, 2015
Air Bags

TL* THE CONTACT OWNS A 2008 DODGE RAM 3500. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 15V313000 (AIR BAGS) AND STATED THAT THE PART WAS NOT AVAILABLE WITHIN A REASONABLE TIME FRAME TO SCHEDULE THE RECALL REPAIR. THE DEALER DID NOT GIVE A SPECIFIC DATE FOR WHEN THE PART WOULD BECOME AVAILABLE. THE CONTACT WENT …

Read full complaint

TL* THE CONTACT OWNS A 2008 DODGE RAM 3500. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 15V313000 (AIR BAGS) AND STATED THAT THE PART WAS NOT AVAILABLE WITHIN A REASONABLE TIME FRAME TO SCHEDULE THE RECALL REPAIR. THE DEALER DID NOT GIVE A SPECIFIC DATE FOR WHEN THE PART WOULD BECOME AVAILABLE. THE CONTACT WENT TO THE DEALER TWICE AND WAS PLACED ON A WAITING LIST FOR AN EXTENDED PERIOD OF TIME. THE MANUFACTURER COULD NOT PROVIDE AN ESTIMATED DATE FOR WHEN THE CONTACT'S VEHICLE WOULD RECEIVE THE RECALL REPAIR. THE CONTACT WAS NOT EXPERIENCING A FAILURE. PARTS DISTRIBUTION DISCONNECT.

NHTSA ODI #10789902

172,000 miles · Sep 27, 2015
Electrical SystemFire

ARRIVED AT LOWES, LEFT THE TRUCK RUNNING OUT FRONT OF THE STORE WHILE UNDLOADING RIDING MOWER TO RETURN. WHEN WE CAME BACK OUT VEHICLE HAD SHUT OFF AND SMOKE COMING FROM UNDER THE HOOD. LIFTED THE HOOD AND NOTED FUSE BOX SMOKING. JUMPED BACK IN TRUCK AND MADE SURE ENGINE TURNED OFF AND KEY OUT OF INGNITION. WHILE WAITING FOR FRI…

Read full complaint

ARRIVED AT LOWES, LEFT THE TRUCK RUNNING OUT FRONT OF THE STORE WHILE UNDLOADING RIDING MOWER TO RETURN. WHEN WE CAME BACK OUT VEHICLE HAD SHUT OFF AND SMOKE COMING FROM UNDER THE HOOD. LIFTED THE HOOD AND NOTED FUSE BOX SMOKING. JUMPED BACK IN TRUCK AND MADE SURE ENGINE TURNED OFF AND KEY OUT OF INGNITION. WHILE WAITING FOR FRIENDS TO TOWE THE TRUCK, WIPERS STARTED HORN AND ALARM STARTED THEN CAR STARTED UP AND TOOK OFF ACROSS THE PARKING LOT. LUCKILY THERE WERE NO VEHICLE OR PERSONS IN FRONT OF THE VEHICLE WHEN THIS HAPPENED AND WAS GOOD THING WE WAITED OUTSIDE FOR FRIENDS INSTEAD OF RETURNING INSIDE THE STORE. MY HUSBAND WAS ABLE TO JUMP IN THE TRUCK, BUT WITHOUT THE KEY IN THE IGNITION HE WAS UNABLE TO BRAKE THE TRUCK OR STEER THE TRUCK, SO BECAUSE IT WAS A MANUAL HE WAS ABLE TO GET IT OUT OF GEAR AND APPLY EMERGENCY BRAKE. SADLY AFTER THIS OCCURRED I HAVE DISCOVERED EVEN MORE HORRIFIC INCIDENCES WHERE THIS HAS HAPPENED TO PEOPLE WHILE DRIVING LEAVING THEM WITHOUT STEERING OR BRAKES. DODGE IS AWARE OF THE PROBLEM AND STILL NO RECALL. I'VE EVEN SEEN THIS DESCRIBED AS A "COMMON OCCURANCE".......REALLY ! NO CRASH OR FATALITIES THIS TIME, BUT BY THE SOUND TOO MANY NEAR MISSES AND WHO KNOWS HOW MANY HAVE BEEN CAUSED BY THIS PROBLEM.

NHTSA ODI #10777948

150,000 miles · Sep 16, 2015
Power TrainSuspension

TL* THE CONTACT OWNS A 2008 DODGE RAM 3500. WHILE DRIVING 20 MPH, AN ABNORMAL NOISE WAS HEARD FROM THE REAR OF THE VEHICLE. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBERS: 13V528000 (POWER TRAIN) AND 15V313000 (AIR BAGS); HOWEVER, THE PART TO DO THE REPAIR WAS UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EX…

Read full complaint

TL* THE CONTACT OWNS A 2008 DODGE RAM 3500. WHILE DRIVING 20 MPH, AN ABNORMAL NOISE WAS HEARD FROM THE REAR OF THE VEHICLE. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBERS: 13V528000 (POWER TRAIN) AND 15V313000 (AIR BAGS); HOWEVER, THE PART TO DO THE REPAIR WAS UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS NOT MADE AWARE OF THE ISSUE. THE FAILURE MILEAGE WAS 150,000.

NHTSA ODI #10764074

621,000 miles · Sep 2, 2015
Electrical System

TL* THE CONTACT OWNS A 2008 DODGE RAM 3500. WHILE DRIVING APPROXIMATELY 70 MPH, THE ODOMETER SEIZED. THE VEHICLE WAS TAKEN TO A DEALER WHO STATED THAT "IT WAS NOT PUBLIC KNOWLEDGE THAT WHEN A TRUCK GOT TO 621,000, THIS PROBLEM OCCURRED"; THE INSTRUMENT CLUSTER AND/OR THE ELECTRONIC CONTROL MODULE WOULD NEED TO BE REPLACED. THE V…

Read full complaint

TL* THE CONTACT OWNS A 2008 DODGE RAM 3500. WHILE DRIVING APPROXIMATELY 70 MPH, THE ODOMETER SEIZED. THE VEHICLE WAS TAKEN TO A DEALER WHO STATED THAT "IT WAS NOT PUBLIC KNOWLEDGE THAT WHEN A TRUCK GOT TO 621,000, THIS PROBLEM OCCURRED"; THE INSTRUMENT CLUSTER AND/OR THE ELECTRONIC CONTROL MODULE WOULD NEED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE APPROXIMATE FAILURE MILEAGE WAS 621,000.

NHTSA ODI #10761015

140,000 miles · Aug 19, 2015
Electrical SystemPower Train

TL* THE CONTACT OWNS A 2008 DODGE RAM 3500. WHEN THE IGNITION KEY WAS TURNED TO THE ON POSITION, THE VEHICLE FAILED TO START INTERMITTENTLY. THE CONTACT MENTIONED THAT THE FAILURE ONLY OCCURRED IN COLD TEMPERATURES. THE VEHICLE WAS TAKEN TO THE DEALER WHERE IT WAS DIAGNOSED THAT THE BATTERY NEEDED TO BE REPLACED. THE VEHICLE WAS…

Read full complaint

TL* THE CONTACT OWNS A 2008 DODGE RAM 3500. WHEN THE IGNITION KEY WAS TURNED TO THE ON POSITION, THE VEHICLE FAILED TO START INTERMITTENTLY. THE CONTACT MENTIONED THAT THE FAILURE ONLY OCCURRED IN COLD TEMPERATURES. THE VEHICLE WAS TAKEN TO THE DEALER WHERE IT WAS DIAGNOSED THAT THE BATTERY NEEDED TO BE REPLACED. THE VEHICLE WAS REPAIRED BUT THE FAILURE RECURRED. THE VEHICLE WAS THEN TAKEN TO AN INDEPENDENT MECHANIC WHERE IT WAS DIAGNOSED THAT THE CLUTCH SAFETY IGNITION INTERLOCK SWITCH NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE AND STATED THAT THE VIN WAS NOT INCLUDED NHTSA CAMPAIGN NUMBER: 14V795000 (ELECTRICAL SYSTEM). THE FAILURE MILEAGE WAS 140,000.

NHTSA ODI #10749729

40,000 miles · Aug 15, 2015
Steering

BETWEEN THE SPEEDS OF 50/75 HITTING BUMPS SEPARATION OF ROAD & BRIDGES WILL TRIGGER THE DEATH WOBBLE I BEEN DEALING WITH THIS ISSUE FOR ALMOST 6 YRS I'VE INSTALLED NEW TRACK BAR,INNER & OUTER TIE RODS LAST MONT KEEPING THE TIRES ROTATED & BALANCE ALMOST GOT REAREND BY 18 WHEELER HAD TO SLM ON BRAKES LOCK EM DOWN TO STOP THIS BRU…

Read full complaint

BETWEEN THE SPEEDS OF 50/75 HITTING BUMPS SEPARATION OF ROAD & BRIDGES WILL TRIGGER THE DEATH WOBBLE I BEEN DEALING WITH THIS ISSUE FOR ALMOST 6 YRS I'VE INSTALLED NEW TRACK BAR,INNER & OUTER TIE RODS LAST MONT KEEPING THE TIRES ROTATED & BALANCE ALMOST GOT REAREND BY 18 WHEELER HAD TO SLM ON BRAKES LOCK EM DOWN TO STOP THIS BRUTAL SHAKE VERY IRRITATING DEALING WITH THIS AT SEVERAL TIMES IT WILL SHAKE INTO THE OTHER LANE ALMOST CAUSING WREAKS PLEASE HELP THANKS [XXX]. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6). *TR

NHTSA ODI #10748920

89,648 miles · Aug 6, 2015
Tires

TL* THE CONTACT OWNS A 2008 DODGE RAM 3500 EQUIPPED WITH CAPITOL H/T (NA) TIRES, SIZE: LT235/80R17 (NA). THE CONTACT STATED THAT WHILE DRIVING APPROXIMATELY 60 MPH, THE CONTACT COULD FEEL A VIBRATION IN THE FRONT DRIVER SIDE TIRE. THE CONTACT INSPECTED THE VEHICLE AND STATED THAT THE FRONT DRIVER SIDE TIRE BLEW OUT. THE VEHICLE…

Read full complaint

TL* THE CONTACT OWNS A 2008 DODGE RAM 3500 EQUIPPED WITH CAPITOL H/T (NA) TIRES, SIZE: LT235/80R17 (NA). THE CONTACT STATED THAT WHILE DRIVING APPROXIMATELY 60 MPH, THE CONTACT COULD FEEL A VIBRATION IN THE FRONT DRIVER SIDE TIRE. THE CONTACT INSPECTED THE VEHICLE AND STATED THAT THE FRONT DRIVER SIDE TIRE BLEW OUT. THE VEHICLE WAS TAKEN TO A DEALER, WHERE IT WAS CONFIRMED THAT THE TREAD SEPARATED FROM THE FRONT DRIVER SIDE TIRE AND NEEDED TO BE REPLACED. THE TIRE WAS REPLACED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE APPROXIMATE VEHICLE FAILURE MILEAGE WAS 89,648 AND THE TIRE FAILURE MILEAGE WAS 15,000.

NHTSA ODI #10746744

95,000 miles · Aug 5, 2015
Electrical SystemExterior Lighting

AFTER MY SON PURCHASED HIS 08 MEGA CAB 4X4 , HIS SIGNAL LIGHTS STARTED CROSSING, IN OTHER WORDS WHEN YOU TURN ON LEFT IT SIGNALED RIGHT AND WIPERS DON,T FUNCTION EXACTLY RIGHT WHEN CHANGING LANES TRAFFIC THOUGHT WE WERE GOING RIGHT AND THEY WENT LEFT ON THE INTERSTATE AND WE ALMOST COLLIDED BOTH GOING TO THE LEFT

NHTSA ODI #10746611

121,145 miles · Aug 1, 2015
EnginePower TrainVehicle Speed Control

ETC (ELECTRONIC THROTTLE CONTROL) WHEN THIS LIGHT COMES ON FLASHING IT GOES INTO LIMP MODE (IDLE) THIS IS A REAL SAFETY CONCERN ESPECIALLY IN TRAFFIC WHEN TOWING A TRAILER. I BOUGHT THE TRUCK NEW FROM CITY AUTO PLAZA, CANON CITY, CO. I BROUGHT THE TRUCK INTO CITY AUTO PLAZA JUNE 4TH 2014 WHEN THE ETC LIGHT WAS FLASHING. THEY RE…

Read full complaint

ETC (ELECTRONIC THROTTLE CONTROL) WHEN THIS LIGHT COMES ON FLASHING IT GOES INTO LIMP MODE (IDLE) THIS IS A REAL SAFETY CONCERN ESPECIALLY IN TRAFFIC WHEN TOWING A TRAILER. I BOUGHT THE TRUCK NEW FROM CITY AUTO PLAZA, CANON CITY, CO. I BROUGHT THE TRUCK INTO CITY AUTO PLAZA JUNE 4TH 2014 WHEN THE ETC LIGHT WAS FLASHING. THEY REPLACED THE GAS PEDAL THE FOLLOWING DAY THE ETC LIGHT CAME ON. JUNE 11TH 2014 THEY RE-CRIMPED THE PLUG ON THE PEDAL SENSOR AND THE C130 CONNECTOR UNDER THE HOOD. THAT LASTED ABOUT A MONTH AND A HALF. ON JULY 29TH 2014 THEY HARDWIRED AROUND THE C130 CONNECTOR. THAT LASTED ABOUT 8 MONTHS BROUGHT TRUCK IN ON MARCH 9TH 2015, THE ETC LIGHT HAD GONE OFF BY THE TIME I GOT TO CITY AUTO PLAZA BUT IT WAS THE SAME CODE IN STORAGE P2121. THE ETC LIGHT CAME ON AGAIN IN MAY 12TH 2015 BROUGHT IT BACK AND THEY RE-CRIMPED THE PEDAL SENSOR PUT SOME LUBE AND PULLED THE PLUGS OFF THE PCM AND BLEW THEY OUT AND PUT SOME LUBE IN THE PLUGS. JULY 8TH 2015 THE ETC LIGHT CAME BACK ON FLASHING SO I BROUGHT IT DOWN TO CITY AUTO PLAZA AGAIN AND THEY HARDWIRED FROM THE GAS PEDAL ALL THE WAY TO THE PCM. THAT LASTED 2 DAYS AND THE ETC LIGHT CAME BACK ON GOING INTO LIMP MODE. BROUGHT IT IN AGAIN ON JULY 16TH THE LIGHT WAS OFF. THEY TEST DROVE IT NUMEROUS TIME COULDN'T GET THE ETC LIGHT TO COME ON BUT IT STILL HAD THE SAME CODE IN STORAGE P2121. SO THE SWAPPED OUT ACCELERATOR PEDALS GOT THE TRUCK BACK ON THE JULY 21ST. ON JULY 29TH I BROUGHT THE TRUCK IN TO TROUBLESHOOT THE AC (AIR CONDITIONER) STARTED THE TRUCK IN THE PARKING LOT AND THE ETC LIGHT WAS FLASHING. TRAVIS THE TECH THAT WORKS ON MY TRUCK HAS BROUGHT IN TECH SUPPORT FROM CHRYSLER. TRAVIS ALSO GOOGLE'D IT AND THIS IS NOT JUST MY TRUCK. HE SAW TRUCKS FROM 2004 TO 2009 WITH THESE SAME PROBLEMS. WHY CAN'T CHRYSLER FIGURE THIS OUT? DOES SOMEONE HAVE TO GET IN AND ACCIDENT OR DIE BEFORE THEY FIGURE IT OUT?

NHTSA ODI #10745500

Official recalls

9

16V352000 · Air Bags:frontal:passenger Side:inflator Module

May 24, 2016

Chrysler (FCA US LLC) expanded the affected population to include 73,712 2005-2009 RAM 2500 trucks produced at the St. Louis North Assembly Plant. With this change, Chrysler is recalling certain model year 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2010 RAM 3500 Cab Chassis, 2008-2010 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2012 Jeep Wrangler, 2008-2012 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2012 Chrysler 300, 2006-2012 Dodge Charger, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AL, CA, FL, GA, HI, LA, MS, SC, TX, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Chrysler is also recalling 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2009 RAM 3500 Cab Chassis, 2008-2009 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2009 Jeep Wrangler, 2008-2009 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2009 Chrysler 300, 2006-2009 Dodge Charger, 2005-2009 Dodge Dakota and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AZ, AR, DE, Washington D.C., IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV, or "Zone B." Lastly, unless included in "Zone A" or "Zone B" above, Chrysler is recalling certain 2005-2008 RAM 2500, 2006-2008 RAM 3500, 2007-2008 RAM 3500 Cab Chassis, 2008 RAM 4500 and 5500 Cab Chassis, 2004-2008 Dodge Durango, 2007-2008 Chrysler Aspen, 2007-2008 Jeep Wrangler, 2008 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2008 Chrysler 300, 2006-2008 Dodge Charger, 2005-2008 Dodge Dakota, and 2006-2008 Mitsubishi Raider vehicles originally sold, or registered, in AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY.

Consequence & remedy

Consequence: These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. These inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling. An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the Chrysler, Dodge, Jeep and RAM owners. Mitsubishi owners will be notified by their company. Dealers will replace the passenger frontal air bag inflator, free of charge. The recall began on March 27, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S43. Note: This recall supersedes recall 14V-7700.

15V313000 · Air Bags:frontal:driver Side:inflator Module

May 26, 2015

Chrysler (FCA US LLC) is recalling certain model year 2005-2009 Dodge Ram 2500, 2004-2008 Dodge Ram 1500 and Durango, 2006-2009 Dodge Ram 3500, 2008-2010 Dodge Ram 4500 and 5500, 2007-2008 Chrysler Aspen, 2005-2010 Chrysler 300, 300C, 300S, and SRT8, 2006-2010 Dodge Charger, 2005-2008 Magnum, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles. The affected vehicles are equipped with a dual-stage driver frontal air bag that may be susceptible to moisture intrusion which, over time, could cause the inflator to rupture.

Consequence & remedy

Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the affected Chrysler and Dodge owners and Mitsubishi will notify the affected Raider owners. Dealers will replace the driver's frontal air bag inflator, free of charge. The recall began for Chrylser on June 8, 2015. The recall for Mitsubishi started on June 24, 2015. Chrysler and Dodge owners may contact Chrysler customer service at 1-800-853-1403. Mitsubishi owners may call 1-888-648-7820. Chrysler's number for this recall is R25. Note: This recall supersedes recall 14V817 in its entirety. Vehicles that have had their driver side frontal air bag replaced previously need to have their air bag replaced under this recall as well.

13V528000 · Steering:linkages:tie Rod Assembly

Nov 6, 2013

Chrysler Group LLC (Chrysler) is recalling certain model year 2003-2008 Dodge RAM 2500 4x4 and 3500 4x4, model year 2007-2008 Dodge RAM 3500 4x2 Cab Chassis and model year 2006-2008 Dodge RAM 1500 Mega Cab 4x4 trucks manufactured February 12, 2002, through February 13, 2008. The left tie rod assembly may break.

Consequence & remedy

Consequence: A failure of the tie rod assembly may result in a loss of steering control, increasing the risk of a crash.

Remedy: Chrysler notified owners and launched its recall campaign in January 2014. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N62.

13V529000 · Steering:linkages:tie Rod Assembly

Nov 6, 2013

Chrysler Group LLC (Chrysler) is recalling certain model year 2008-2012 RAM 2500 4X4 and 3500 4X4 trucks, 2008-2012 Dodge RAM 3500 4x2 Cab Chassis, and model year 2008 Dodge RAM 1500 Mega Cab 4x4. The left tie rod assembly may break.

Consequence & remedy

Consequence: A failure of the tie rod assembly may result in a loss of steering control, increasing the risk of a crash.

Remedy: Chrysler notified owners on January 16, 2014 that dealers would inspect vehicles and replace the steering linkage assembly, if necessary. On or about February 27, 2014, Chrysler ceased its recall remedy program due to parts quality concerns, and then re-initiated it on or about April 14, 2014. In July 2015, and under a consent order with NHTSA, the company agreed to offer owners three options for remedying their vehicles: perform the original remedy, offer to repurchase the vehicle at the fair market value plus 10%, or offer an additional incentive offer towards the purchase of a new Dodge, Jeep, Chrysler, or Fiat vehicle. Chrysler will notify owners of the new recall options in a letter expected to be mailed on August 31, 2015. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N49.

11V350000 · Steering:linkages:tie Rod Assembly

Jul 6, 2011

CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2008-2011 DODGE RAM 2500/3500 4X4, MANUFACTURED FROM FEBRUARY 14, 2008, THROUGH MARCH 28, 2011; MODEL YEAR 2008-2011 DODGE RAM 3500 CAB CHASSIS 4X2, MANUFACTURED FROM FEBRUARY 14, 2008, THROUGH MARCH 28, 2011; AND MODEL YEAR 2008 DODGE RAM 1500 MEGA CAB 4X4, MANUFACTURED FROM FEBRUARY 14, 2008, THROUGH AUGUST 15, 2008, BECAUSE THE LEFT TIE ROD BALL STUD MAY FRACTURE. THIS CONDITION TENDS TO OCCUR DURING LOW SPEED PARKING LOT TYPE MANEUVERS WHEN THE CUSTOMER IS MAKING A TIGHT TURN. ADDITIONALLY, MODEL YEAR 2003-2008 DODGE RAM 2500/3500 VEHICLES MAY HAVE RECEIVED THE AFFECTED TIE ROD ASSEMBLY AS A REPLACEMENT PART DURING NORMAL SERVICE.

Consequence & remedy

Consequence: THIS CONDITION COULD RESULT IN THE POTENTIAL LOSS OF DIRECTIONAL STABILITY IN THE LEFT HAND FRONT WHEEL, INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL INSPECT THE TIE ROD ENDS FOR RELATIVE ORIENTATION AND REPLACE THE LEFT OUTER TIE ROD AS REQUIRED AND PERFORM A FRONT END TOE ALIGNMENT AS NEEDED. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON OCTOBER 3, 2011. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.

09V434000 · Equipment:appliance:air Conditioner

Nov 13, 2009

E-N-G MOBILE SYSTEM IS RECALLING CERTAIN MODEL YEAR 2008 CHEVROLET W5500, MODEL YEAR 2007-2009 DODGE 3500, MODEL YEAR 2009 MIGHTY MOVER, MODEL YEAR 2006-2009 FORD E-250, E-350 AND E-450, MODEL YEAR 2008-2009 GMC W4500, MODEL YEAR 2007 INTERNATIONAL 4300, MODEL YEAR 2009 TOYOTA LAND CRUISER VEHICLES EQUIPPED WITH CARRIER AIRV CEILING UNITS, MODEL NOS. 68RV0010BA, 68RV0012CA, AND 68RV0010EA. THE HEATER ELEMENT IN THESE ASSEMBLIES MAY BE DEFECTIVE WHICH COULD CAUSE THE UNIT TO CREATE SMOKE OR SPARKS.

Consequence & remedy

Consequence: THIS DEFECT COULD RESULT IN A FIRE.

Remedy: E-N-G MOBILE SYSTEM WILL NOTIFY OWNERS AND THE VEHICLES WILL BE REPAIRED BY CARRIER FREE OF CHARGE. PLEASE SEE CARRIER'S DEFECT REPORT 09E-053. THE SAFETY RECALL IS EXPECTED TO BEGIN DURING DECEMBER 2009. OWNERS MAY CONTACT CARRIER AT 1-877-584-7059 OR E-N-G MOBILE SYSTEM AT 1-925-798-4060.

09V005000 · Steering:linkages:tie Rod Assembly

Jan 9, 2009

CHRYSLER IS RECALLING 32,782 MY 2008-2009 DODGE RAM 2500, 3500 AND 3500 CAB CHASSIS PICKUP TRUCKS EQUIPPED WITH POWERS AND SONS STEERING LINKAGE. THE STEERING LINKAGE DRAG LINK INNER TIE ROD TO PITMAN ARM BALL STUD MAY FRACTURE. ALSO THE STEERING LINKAGE DAMPER ATTACHING THE BRACKET MAY YIELD AND SHIFT ON THE LINKAGE.

Consequence & remedy

Consequence: THIS COULD RESULT IN A LOSS OF STEERING CONTROL AND THE RESTRICTED ABILITY TO TURN THE VEHICLE IN ONE DIRECTION INCREASING THE RISK OF A CRASH WITHOUT WARNING.

Remedy: DEALERS WILL REPLACE THE STEERING LINKAGE DRAG LINK INNER TIE ROD END ASSEMBLY, AND INSPECT THE STEERING LINKAGE DAMPER BRACKET FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN ON OR BEFORE FEBRUARY 16, 2009. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.

08V641000 · Engine And Engine Cooling:engine:diesel

Dec 5, 2008

CHRYSLER IS RECALLING 108,429 MY 2007-2008 DODGE RAM 2500 AND 3500 PICKUP TRUCKS EQUIPPED WITH 6.7L DIESEL ENGINES. A SILENCER PAD CAN SAG AND CONTACT THE EXHAUST GAS RECIRCULATION (EGR) COOLER.

Consequence & remedy

Consequence: THIS COULD RESULT IN AN ENGINE COMPARTMENT FIRE.

Remedy: DEALERS WILL ADD A BRACKET TO SUPPORT THE ENGINE COMPARTMENT SILENCER PAD ADJACENT TO THE EGR COOLER. THE RECALL IS EXPECTED TO BEGIN DURING DECEMBER 2008. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.

08V344000 · Trailer Hitches

Jul 28, 2008

KNAPHEIDE IS RECALLING 108 MY 2006-2008 PRO SERIES TRUCK BEDS EQUIPPED WITH AN ICC BUMPER WHICH INCLUDED A PROVISION FOR A BALL HITCH. THERE MAY BE AN INSUFFICIENT WELD ATTACHING THE HITCH CHANNEL TO THE SUPPORTING STRUCTURE.

Consequence & remedy

Consequence: THIS COULD RESULT IN BENDING OF THE HITCH CHANNEL OR THE HITCH COULD BE PULLED OFF THE VEHICLE, INCREASING THE RISK OF A CRASH.

Remedy: KNAPHEIDE WILL OFFER TWO REMEDIES TO ITS CUSTOMERS: (1) FOR THOSE CUSTOMERS WHO DO NOT USE THE HITCH, THE HITCH WILL BE REMOVED FROM THE TRUCK BED AND REPLACED WITH AN ICC BUMPER; OR (2) FOR THOSE CUSTOMERS WHO NEED A HITCH, A RECEIVER HITCH ASSEMBLY WILL BE ADDED TO THE EXISTING HITCH ASSEMBLY AND ALL SUSPECT WELD JOINTS WILL BE RE WELDED. THE RECALL BEGAN ON AUGUST 15, 2008. OWNERS MAY CONTACT KNAPHEIDE AT 1-877-473-5763.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

3

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

AQ14003 · Chrysler's Execution Of 13V-528 & 529

Opened Oct 20, 2014 · Closed May 16, 2016

Status: closed (inferred from source dates) · Steering:linkages:tie Rod Assembly

RMD opened this audit query (AQ) investigation in order to better understand and evaluate Chrysler's process(es) for timely and efficient execution of its safety recall campaigns, including its oversight and management of its parts division Mopar.Prior to opening this investigation, RMD had raised concerns with the company related to its execution of two safety recalls, 13V-528 and 13V-529, both of which involved safety defects that could cause the involved vehicles, FCA?s heavier Dodge Ram trucks, to lose steering control suddenly and without warning.Specifically, RMD inquired about the availability of parts for recall repairs, by email and phone on January 15, 2014 and February 19, 2014, due to the volume of complaints it was receiving from owners alleging parts scarcity and parts restrictions. FCA steadfastly denied it had placed parts restrictions on its dealers to manage issues of parts scarcity.FCA shared material showing it had uncommitted stock of parts available for its dealers. Nevertheless, consumer complaints of lack of parts continued.RMD made independent inquiries tosome dealers tobetter understand the conflicting claims between owners alleging lack of ability to repair their defective vehicles due to lack of parts, and FCA?s information showing availability of parts.Dealers informed and provided documentation to RMD on February 21, 2014 and February 25, 2014 showing FCA had, in fact, put into place parts restrictions and, further, had in some instances canceled dealerships? back orders for parts.In addition, during the course of its dialogue with dealers, RMD discovered that FCA had notified their dealerships on February 27, 2014 to return the recall remedy parts over quality concerns, and had therefore effectively canceled its safety recall program without notification to NHTSA. RMD issued a request for information (IR) on October 21, 2014.The company failed to respond to a number of the questions RMD asked that required it to produce specifics surrounding the repairs and parts ordering process with the recalls, including a question about whether a dealer order for recall parts could be canceled and under what circumstances.

PE11009 · Outer Tie Rod Failure

Opened Apr 4, 2011 · Closed Feb 6, 2012

Status: closed (inferred from source dates) · Steering:linkages:tie Rod Assembly

ODI received complaints regarding failing tie rod ball studs on Model Year 2008-2011 Dodge Ram 2500 and 3500 vehicles resulting in loss of steering control.Chrysler concluded that misalignment of the left (driver side) ball stud on vehicles built with the Cross Car steering linkage system could allow contact between the bull stud and the ball housing which could weaken the stud and result in fracture.Chrysler submitted a recall notice on August 15, 2011 involving certain MY 2003-2011 Ram 2500 and Ram 3500 pickup trucks built or repaired with the Cross Car steering linkage.Chrysler will inspect, repair or realign the front end of the subject vehicles as needed.Chrysler's announcement of a safety recall on this matter addresses ODI's concerns.The ODI reports cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10332525, 10357937, 10366591, 10303744, 10377166, 10373240, 10343969, 10375403, 10324831, 10373546, 10370771.