IllustrationTHE REAR AXLE PINION NUT WAS RECALLED LAST YEAR AROUND JUNE 2013 IT IS NOW JAN 2014 ALL THE DEALERSHIP CAN DO IS CALL AND HARASS ME ABOUT TRADING THE TRUCK IN AND NOT A WORD ON THE REPLACEMENT REAR AXLE PINION NUT--PLEASE HELP. *TR
2009 Dodge RAM 1500
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2009 Dodge RAM 1500 do not stand out strongly from the model-year median of 520.
About this comparison →How this year compares
Owner complaints by model year
Compare all RAM 1500 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
740–25K
10725–50K
13150–75K
10475–100K
94100–150K
32150K+
542 reports with mileage · 128 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Power Train. Review the 231 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 97 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 50 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
29 crash reports2 fire reports18 injury reports
Suspension complaints
34 reportsI RECEIVED THE RECALL NOTIFICATION AND TRIED TO HAVE MY VEHICLE CHECKED BY THE DEALER. 3 WEEKS LATER AFTER 3 ADDITIONAL ATTEMPTS I WAS FINALLY ABLE TO BE SEEN WITH AN APPOINTMENT. THE INSPECTION TOOK 30 MIN OR LESS BUT DID FIND THAT A PART NEEDS TO BE REPLACED. THEY DO NOT HAVE THE PART AND IS EXPECTED TO TAKE 3-6 WEEKS GET IN. …
Read full complaint
I RECEIVED THE RECALL NOTIFICATION AND TRIED TO HAVE MY VEHICLE CHECKED BY THE DEALER. 3 WEEKS LATER AFTER 3 ADDITIONAL ATTEMPTS I WAS FINALLY ABLE TO BE SEEN WITH AN APPOINTMENT. THE INSPECTION TOOK 30 MIN OR LESS BUT DID FIND THAT A PART NEEDS TO BE REPLACED. THEY DO NOT HAVE THE PART AND IS EXPECTED TO TAKE 3-6 WEEKS GET IN. IN THE MEAN TIME I'VE BEEN ADVISED TO WAIT AND THE VEHICLE IS SAFE TO DRIVE. *TR
I RECEIVED A RECALL NOTICE ALMOST 4 MONTHS AGO FOR THE REAR AXLE PINION NUT WHICH COULD RESULT IN A SERIOUS ACCIDENT, AS NOTED ON THE RECALL. I PLACED MY 2ND CALL TODAY TO THE CHRYSLER GROUP RECALL ASSISTANCE CENTER AND WAS AGAIN TOLD THAT THE PARTS TO REPAIR THIS PROBLEM ARE NOT READY. AS A CONSUMER WITH A POTENTIAL SAFETY PROB…
Read full complaint
I RECEIVED A RECALL NOTICE ALMOST 4 MONTHS AGO FOR THE REAR AXLE PINION NUT WHICH COULD RESULT IN A SERIOUS ACCIDENT, AS NOTED ON THE RECALL. I PLACED MY 2ND CALL TODAY TO THE CHRYSLER GROUP RECALL ASSISTANCE CENTER AND WAS AGAIN TOLD THAT THE PARTS TO REPAIR THIS PROBLEM ARE NOT READY. AS A CONSUMER WITH A POTENTIAL SAFETY PROBLEM WITH HIS FAMILY'S MAIN MODE OF TRANSPORTATION, I FIND THIS ANSWER UNACCEPTABLE. IT SEEMS TO ME THAT THIS PROBLEM NEEDS TO REPAIRED IMMEDIATELY AND THAT THE COMPANY HAS HAD PLENTY OF TIME TO MANUFACTURE THE REQUIRED ADHESIVE PATCH. *TR
WHILE DRIVING AT 45 MPH OR FASTER, A RATTLE SOUND CAN BE HEARD FROM THE LEFT REAR SIDE. I CHECKED TO SEE IF ANYTHING WAS WRONG; I DID FIND THAT THE SHOCK WAS NOT FULLY TIGHTEN ON THE TOP BOLT. I WAS ABLE TO MOVE THE TOP PART OF THE SHOCK BY HAND. I TOOK MY VEHICLE TO LARRY H MILLER DODGE IN TUCSON, AZ. THEY SAID THAT NOTHING WAS…
Read full complaint
WHILE DRIVING AT 45 MPH OR FASTER, A RATTLE SOUND CAN BE HEARD FROM THE LEFT REAR SIDE. I CHECKED TO SEE IF ANYTHING WAS WRONG; I DID FIND THAT THE SHOCK WAS NOT FULLY TIGHTEN ON THE TOP BOLT. I WAS ABLE TO MOVE THE TOP PART OF THE SHOCK BY HAND. I TOOK MY VEHICLE TO LARRY H MILLER DODGE IN TUCSON, AZ. THEY SAID THAT NOTHING WAS WRONG WITH THE LEFT REAR, AND NO UNUSUAL SOUNDS WERE HEARD DURING A TEST DRIVE. THEY INFORMED ME THAT A PAYMENT WOULD BE NEEDED TO FURTHER INVESTIGATE THE PROBLEM. PAYMENT WAS NOT MADE, AND SOUND IS STILL PRESENT. MORE SO NOW THEN BEFORE DEALERSHIP INSPECTION. *TR
TL* THE CONTACT OWNS A 2009 DODGE RAM 1500. THE CONTACT RECEIVED A RECALL NOTICE A FEW MONTHS AGO AND STATED THAT THE DEALER INFORMED HIM THE PARTS WERE NOT AVAILABLE. THE MANUFACTURER WAS NOTIFIED BUT THEY WERE UNABLE TO PROVIDE A DATE THAT THE PARTS WOULD BE AVAILABLE. THERE ARE NO FAILURES AT THIS TIME. *TR
TL* THE CONTACT OWNS A 2009 DODGE RAM 1500. THE CONTACT STATED THAT HE RECEIVED A RECALL NOTICE; HOWEVER, THE PARTS WERE UNAVAILABLE. THE MANUFACTURER WAS NOTIFIED BUT THEY WERE UNABLE TO PROVIDE A DATE THAT THE PARTS WOULD BE AVAILABLE. THERE ARE NO FAILURES AT THIS TIME. *TR
TL* THE CONTACT OWNS A 2009 DODGE RAM 1500. THE CONTACT STATED THAT WHILE DRIVING 70 MPH, THE FRONT DRIVER'S SIDE WHEEL SEPARATED FROM THE VEHICLE AS THE WHEEL CAUGHT ON FIRE. THE VEHICLE WAS TOWED TO THE DEALER FOR DIAGNOSIS WHERE IT WAS STATED THAT THE WHEEL HUB BEARINGS WERE FAULTY. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTU…
Read full complaint
TL* THE CONTACT OWNS A 2009 DODGE RAM 1500. THE CONTACT STATED THAT WHILE DRIVING 70 MPH, THE FRONT DRIVER'S SIDE WHEEL SEPARATED FROM THE VEHICLE AS THE WHEEL CAUGHT ON FIRE. THE VEHICLE WAS TOWED TO THE DEALER FOR DIAGNOSIS WHERE IT WAS STATED THAT THE WHEEL HUB BEARINGS WERE FAULTY. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED. THE APPROXIMATE FAILURE MILEAGE WAS 68,000. *TR
WHILE NEGOTIATING SOFT RIGHT TURN, I HEARD A VERY LOUD POPPING, BANGING NOISE, THAT SOUNDED AS IF THE FRONT SUSPENSION HAD LET GO. GOT HOME 2 MINUTES LATER. UNABLE TO DETERMINE CAUSE. COUPLE OF DAYS LATER WHILE BACKING OUT OF DRIVEWAY, I HEARD A LOUD METAL-ON-METAL GRINDING NOISE THAT STOPPED WHEN I SHIFTED INTO DRIVE. FROM T…
Read full complaint
WHILE NEGOTIATING SOFT RIGHT TURN, I HEARD A VERY LOUD POPPING, BANGING NOISE, THAT SOUNDED AS IF THE FRONT SUSPENSION HAD LET GO. GOT HOME 2 MINUTES LATER. UNABLE TO DETERMINE CAUSE. COUPLE OF DAYS LATER WHILE BACKING OUT OF DRIVEWAY, I HEARD A LOUD METAL-ON-METAL GRINDING NOISE THAT STOPPED WHEN I SHIFTED INTO DRIVE. FROM THEN ON, I NOTICED A ROARING/HUMMING THAT I THOUGHT MIGHT BE A TRANSMISSION PROBLEM. HEARD THE LOUD POPPING/BANGING/SCREECHING A COUPLE OF MORE TIMES OVER THE NEXT FEW DAYS. MINIMIZED DRIVING. I TOOK THE TRUCK TO LOCAL DODGE DEALER WHERE THEY DIAGNOSED HUB FAILURE. DROVE A COUPLE OF MILES TO TRUSTED INDEPENDENT GARAGE. HAD LEFT FRONT HUB ASSEMBLY REPLACED. GARAGE OWNER SURPRISED I MADE IT TO HIS SHOP WITHOUT THE WHEEL LOCKING AND COMING OFF. LOOKING AT INTERNET, THE HUB PROBLEM SEEMS VERY COMMON ON DODGE PICKUPS (RECALL ON 2006 MODELS). MANY COMPLAINTS REPORTED ON VARIOUS WEBSITES AFFECTING MODELS FROM 2002-2009, WITH MOST OCCURRING AROUND 53000 MILES. SEVERAL CRASHES REPORTED DUE TO WHEEL SEPARATIONS FROM HUB/BEARING ASSEMBLY FAILURE AND LOCKUP. *TR
DRIVING ON 390N IN ROCHESTER N.Y. AT APPROX. 5PM HEAVY TRAFFIC .LOUD BANG AND REAR TIRES LOCKED UP,, BOTH GRANDDAUGHTERS BEGAN TO SCREAM" WHATS HAPPENING". I HAD NO CLUE. LOOKED TO RIGHT TO TRY TO GET OUT OF TRAFFIC AND SAW WHAT I THOUGHT WAS MY DRIVESHAFT SPIT OUT FROM UNDER R R TIRE.. WE WERE LIFTED UP IN AIR AT BACK OF TRUCK …
Read full complaint
DRIVING ON 390N IN ROCHESTER N.Y. AT APPROX. 5PM HEAVY TRAFFIC .LOUD BANG AND REAR TIRES LOCKED UP,, BOTH GRANDDAUGHTERS BEGAN TO SCREAM" WHATS HAPPENING". I HAD NO CLUE. LOOKED TO RIGHT TO TRY TO GET OUT OF TRAFFIC AND SAW WHAT I THOUGHT WAS MY DRIVESHAFT SPIT OUT FROM UNDER R R TIRE.. WE WERE LIFTED UP IN AIR AT BACK OF TRUCK AND I LOST ALL PROPULSION, MIND YOU MY 5 AND 6 YEAR OLD ARE SCREAMING AS THE OTHER HALF OF THE DRIVE SHAFT POUNDS ON THE PAVEMENT AND BOTTOM OF TRUCK .I STILL HAVE NO IDEA WHAT IS HAPPENING. SOMEHOW AND THAT'S WHAT I TOLD THE SHERIFF I GOT THE TRUCK WHICH WAS NOW FREEWHEELING OFF TO THE SIDE OF THE ROAD APPROX. 75-100 FT FROM MY DRIVESHAFT THAT HIT THE BRIDGE GUARDRAIL AND STOPPED FROM HITTING ANYONE IN TRAFFIC. I COLLECTED MYSELF ,CALMED THE GIRLS WHOS BIG CONCERN WAS NOW,, SOMEONE IS GOING TO SMASH US AND CALLED 911 AND MY DAUGHTER. THEN I LOOKED. MY DRIVESHAFT WAS TORN IN TWO ,OIL AND PARTS WERE EVERYWHERE WE SHOULD BE DEAD BUT WE ARE NOT HONESTLY I HAVE NO CLUE HOW I GOT THAT TRUCK OVER AND STOPPED. ME AND THE GIRLS PRAY EVERY NIGHT FOR GOD TO PROTECT OUR FAMILY AND ANGELS ROAD IN THAT TRUCK THAT DAY.THE TOW TRUCK DRIVER HAD TO SKID THE TRUCK UP ONTO THE FLATBED IT WAS SEIZED SO BADLY,, AND MY DAUGHTER CAME AND SAFELY GOT THE GIRLS OFF THE BUSY HIGHWAY AND HOME. THE HELP TRUCK SAID HE HAD NEVER SEEN ANYTHING LIKE IT..THE DODGE DEALERSHIP HAS BEEN HELPFUL BUT CHRYSLER HAS BEEN UNHELPFUL TO ITS DEALER AND MYSELF WITH AN INDIFFERENCE THAT DISCUSSED ME. I HOPE YOU DO SOMETHING BEFORE SOMEONE DIES!!!! *TR
AIRBAGS FAILED TO GO OFF AFTER COLLISION WITH A FARM IMPLEMENT BEING PULLED BY A FARM TRACTOR. DODGE VEHICLE HAS DAMAGE TO FRAME, PASSENGER SIDE AND FRONT OF VEHICLE. *TR
Official recalls
213V038000 · Power Train:driveline:differential Unit
Feb 6, 2013
Chrysler is recalling certain model year 2009-2012 Ram 1500 trucks manufactured from February 27, 2008, through June 30, 2009, and from December 1, 2009, through October 20, 2011; model year 2009-2011 Dodge Dakota trucks manufactured from February 27, 2007, through June 30, 2009, and from December 1, 2009, through September 30, 2011; model year 2009 Chrysler Aspen trucks manufactured from January 3, 2008, through December 18, 2008; and model year 2009 Dodge Durango trucks manufactured from January 3, 2008, through December 18, 2008. The rear axle pinion nut may loosen due to an undersized pinion spline that can allow relative motion between the nut and companion flange.
Consequence & remedy
Consequence: If the rear axle pinion nut loosens, the axle can lock up and cause a loss of vehicle control and/or a vehicle crash with little warning.
Remedy: On November 7, 2013 Chrysler notified owners that dealers would install a pinion nut retainer, free of charge. In July 2015, and under a consent order with NHTSA, the company agreed to offer owners three options for remedying their vehicles: perform the original remedy, offer to repurchase the vehicle at the fair market value plus 10%, or offer an additional incentive offer towards the purchase of a new Dodge, Jeep, Chrysler, or Fiat vehicle. Chrysler will notify owners of the new recall options in a letter expected to be mailed on August 31, 2015. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N08.
12V474000 · Power Train:driveline:differential Unit
Oct 2, 2012
Chrysler is recalling certain model year 2009-2010, Ram 1500 and Dodge Dakota trucks, manufactured from July 1, 2009, through November 30, 2009, because the rear axle pinion nut may loosen due to a lack of adhesive.
Consequence & remedy
Consequence: If the rear axle pinion nut loosens, the axle can lock up and cause a loss of vehicle control and/or a vehicle crash with little warning.
Remedy: Chrysler will notify owners, and dealers will install a pinion nut retainer, free of charge. The recall began on June 17, 2013. Owners may contact Chrysler at 1-800-247-9753.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2DP14004 · Totally Integrated Power Module Failure
Opened Sep 25, 2014 · Closed Jul 24, 2015
Status: closed (inferred from source dates) · Electrical System
In a letter dated August 21, 2014, the Center for Auto Safety (CAS) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged failures associated with the Totally Integrated Power Module (TIPM) installed in Chrysler SUV?s, trucks, and vans beginning in the 2007 model year. The petitioner alleges that TIPM defects may result in engine stall, airbag non-deployment, failure of fuel pump shutoff resulting in unintended acceleration, fire, and other symptoms. On September 25, 2014, the Office of Defects Investigation (ODI) opened DP14-004 to evaluate the petition for a grant or deny decision. ODI analyzed complaint data provided by CAS as well as complaints submitted to ODI from consumers. In total, there were 296 complaints submitted by the petitioner in the original petition and five supplements, including 271 complaints related to the subject vehicles equipped with TIPM-7. Approximately 3 percent of CAS complaints are related to vehicles equipped with TIPM-6 and ODI?s review of these complaints did not identify any safety defect trends. ODI conducted a detailed review of complaints narratives submitted by CAS and consumers including careful analysis of vehicle repair histories, warranty claims obtained from the manufacturer and any available Customer Assistance Inquiry reports (CAIR). Analysis of the field data indicated that MY2011-2013 Jeep Grand Cherokee and Dodge Durango vehicles exhibited significantly higher complaint rates related to fuel pump relay (FPR) failures than other subject vehicles. In a September 3, 2014 letter to NHTSA, Chrysler submitted a Defect Information Report (DIR) identifying a defect in the FPR within the TIPM-7 which can result in a no start or stall condition in approximately 188,723 model year (MY) 2011 Jeep Grand Cherokee (WK) and Dodge Durango (WD) vehicles manufactured from January 5, 2010 through July 20, 2011 (14V-530).In a February 24, 2015 letter, Chrysler submitted a second DIR expanding the scope of the FPR defect condition to include an additional 338,216 MY 2012 through 2013 Jeep Grand Cherokee vehicles manufactured from September 17, 2010 through August 19, 2013 and MY 2012 through 2013 Dodge Durango vehicles manufactured from January 18, 2011 through August 19, 2013 (15V-115).ODI analysis of the CAS allegations of TIPM defects resulting in stall while driving, airbag non-deployment, unintended acceleration, fire and other faults identified a single defect condition related to 1 of over 60 different circuits in the TIPM assembly. The most common effect of this defect condition, related to the fuel pump relay, was a no-start concern, but it could also result in stall while driving (76 complaints). No valid evidence was presented in support of claims related to airbag non-deployment, unintended acceleration or fire resulting from TIPM faults and these claims were found to be wholly without merit based on review of the field data and design of the relevant systems and components.Except insofar as the petitioner's contentions relate to the defect condition addressed by the Chrysler recalls, the factual bases of the petitioner's contentions that any further investigation is necessary are unsupported. In our view, additional investigation is unlikely to result in a finding that a defect related to motor vehicle safety exists or a NHTSA order for the notification and remedy of a safety-related defect as alleged by the petitioner at the conclusion of the requested investigation. Therefore, in view of the need to allocate and prioritize NHTSA's limited resources to best accomplish the agency's safety mission, the petition is den
PE12021 · Rear Differential Failure
Opened Jul 19, 2012 · Closed Mar 5, 2013
Status: closed (inferred from source dates) · Power Train; Power Train:automatic Transmission; Power Train:axle Assembly; Power Train:driveline; Power Train:driveline:differential Unit; Power Train:driveline:driveshaft; Power Train:transfer Case (4-WHEEL Drive)
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Additional source detail variants (14)
Power Train:automatic Transmission
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:automatic Transmission
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:axle Assembly
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:axle Assembly
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:driveline
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:driveline
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:driveline:differential Unit
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:driveline:differential Unit
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:driveline:driveshaft
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:driveline:driveshaft
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:transfer Case (4-WHEEL Drive)
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:transfer Case (4-WHEEL Drive)
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440