Air Bags. Review the 165 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Steering. Review the 103 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Power Train. Review the 73 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

40 crash reports6 fire reports29 injury reports

What owners actually said

554 reports

Mileage unknown · Dec 3, 2021

Visibility/wiper

Read full complaint

HVAC mode door inoperative causing defroster to not operate and only allowing air out of dash vents causing safety issue when windshield is fogged up due to dew or humidity from rain causing loss of visibility. Mode door broken which involves pulling dashboard and evacuating A/C system at a very significant cost. Have read and heard of many complaint due to broken doors in HVAC system on these vehicles. During early morning hours with dew and during operating vehicle in inclement weather this causes a very serious safety issue. FCA should cover this as it is an unsafe and poor design causing risk to operator and other drivers on the roadways.

NHTSA ODI #11442509

Mileage unknown · Oct 10, 2021

Electrical System

COMPUTER SYSTEM FAILED. APPARENTLY AN ELECTRICAL SPIKE OCCURRED AND FRIED THE MOTHERBOARD. AS A RESULT THE VEHICLE BECAME TOTALY INOPERABLE

NHTSA ODI #11436226

105,000 miles · Oct 26, 2020

Vehicle Speed Control

THE CRUISE CONTROL WILL AUTOMATICALLY DISENGAGE WITHOUT PRESSING BUTTON CREATING DANGEROUS SITUATIONS ON HIGHWAYS.

NHTSA ODI #11366409

102,010 miles · Oct 9, 2020

Suspension

Read full complaint

TL* THE CONTACT OWNS A 2008 DODGE RAM 1500. THE CONTACT STATED WHILE DRIVING AT 35-45 MPH, THERE WAS AN ABNORMAL WINDING NOISE DETECTED. THERE WERE NO WARNING LIGHTS ILLUMINATED. THE CONTACT CHECKED UNDER THE VEHICLE FOR PLAY IN THE DRIVE TRAIN. ADDITIONALLY WHILE DRIVING 25 MPH, THE WINDING NOISE INCREASED AND THERE WAS AN ABNORMAL BANGING NOISE AND THE DRIVE SHAFT SEPARATED FROM THE REAR END AND WAS ON THE GROUND. THERE WAS OIL LEAKING AND THE PINION WAS JAMMED. THE VEHICLE WAS TOWED TO KEY CHRYSLER JEEP DODGE RAM - TOBEY AUTO GROUP 2020 N DETROIT ST, XENIA, OH 45385 (937) 347-5155 WHERE IT WAS DIAGNOSED THAT THE REAR END AND DRIVE SHAFT NEEDED TO REPLACED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOT CONTACTED. THE FAILURE MILEAGE WAS 102,010.

NHTSA ODI #11363603

147,000 miles · Sep 29, 2020

Engine

ROCKER ARM CAME OFF LIFTER, BROKEN LIFTER SPRING. TOLD IT WAS A COMMON VALVE SEAT FAILURE ISSUE FOR THIS VEHICLE. 147,000 REGULAR MAINTENANCE WAS PERFORMED. SHOP SAID THEY HAVE SEEN THIS MANY TIMES. POOR DESIGN/MATERIAL.

NHTSA ODI #11361677

147,000 miles · Sep 4, 2020

Air BagsSeat BeltsService BrakesCrash

I WAS GETTING OFF WORK AND GOING ABOUT 25 MPH ON THE STREET WHEN I WAS INVOLVED IN A HEAD ON COLLISION, I HAD SEEN THE LIGHT CHANGE WHEN I PUSHED ON THE BRAKE PEDAL, I HEARD A CRUNCHING NOISE AND NO BRAKES. ALL I COULD DO WAS HOLD ON TO THE STEERING WHEEL. THE SEAT BELT DID NOT LOCK UP AND THE AIR BAGS DID NOT DEPLOY, WITH ME EN…

Read full complaint

NHTSA ODI #11353229

180,000 miles · Aug 27, 2020

Fuel/propulsion System

Read full complaint

ON MORE THAN 1 OCCASION, AFTER FILLING THE GASOLINE TANK, THE VEHICLE HAS STALLED SHORTLY AFTER BEING FILLED. YESTERDAY, I FILLED THE TANK. AWARE OF THIS ISSUE FROM PAST EXPERIENCE, I AVOIDED "OVERFILLING" IT. APPROXIMATELY 3 OR 4 MILES LATER, I MADE A RIGH TURN AT LOW SPEED TO ENTER A PARKING LOT AND THE VEHICLE STALLED. I LOST POWER STEERING AND STRUGGLED TO GET IT TURNED SAFELY. AT FIRST IT WOULDN'T CRANK, BUT EVENTUALLY I DID GET THE TRUCK RESTARTED. I CONDUCTED SOME BUSINESS, THEN WENT BACK TO THE TRUCK AND STARTED IT TO HEAD HOME. AGAIN AS I WAS TURNING RIGHT TO EXIT THE PARKING LOT, THE VEHICLE STALLED AND I HAD TO STRUGGLE TO GET IT TO RESTART. THIS IS EXTREMELY DANGEROUS AND FROM INTERNET RESEARCH, I KNOW OTHERS ARE EXPERIENCING THE SAME THING.

NHTSA ODI #11351674

160,000 miles · Jul 30, 2020

Power TrainCrash

Read full complaint

TL* THE CONTACT OWNS A 2008 DODGE RAM 1500. THE CONTACT STATED THAT WHILE DRIVING APPROXIMATELY 45 MPH AND DESCENDING DOWN A HILL A LOUD BANGING NOISE WAS HEARD AND THE REAR WHEELS SUDDENLY LOCKED UP CAUSING THE DRIVER TO LOSE CONTROL OF THE VEHICLE CRASHING INTO A DITCH. DURING THE CRASH NO INJURIES WERE REPORTED. A POLICE REPORT WAS TAKEN AT THE SCENE AND THE VEHICLE WAS TOWED AWAY. THE VEHICLE WAS EXAMINED BY AN INDEPENDENT MECHANIC WHO DIAGNOSED THAT THE PINION NUT HAD FAILED. THE LOCAL DEALER AND MANUFACTURER WERE NOT NOTIFIED. THE FAILURE MILEAGE WAS 160,000.

NHTSA ODI #11342394

125,000 miles · Jul 21, 2020

Unknown Or Other

THE WARRANTY HAS BEEN CANCELED DUE TO SOME INSPECTIONS THAT WERE NOT PERFORMED MY THE DEALERSHIPS THIS WAS A LIFETIME WARRANTY AND THEY ARE NOT STANDING BEHIND THEIR CONTRACT

NHTSA ODI #11340733

179,601 miles · Jun 5, 2020

Service Brakes

Read full complaint

TL* THE CONTACT OWNS A 2008 DODGE RAM 1500. THE CONTACT STATED THAT WHILE DRIVING AT AN UNKNOWN SPEED, THE VEHICLE MADE A LOUD NOISE AND JERKED WITHOUT WARNING. THE VEHICLE WAS TAKEN TO THE IG BURTON DODGE DEALER LOCATED AT 19 S. DUPONT BLVD, SMYRNA, DE 19977, WHERE THE BRAKE PADS AND ROTORS WERE REPLACED. THE FAILURE RECURRED. THE VEHICLE WAS TAKEN BACK TO THE SAME DEALER WHERE THE TECHNICIAN REPLACED THE ROTORS, BRAKE CALPERS AND HOSE. THE MANUFACTURER WAS NOT MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS APPROXIMATELY 179,601.

NHTSA ODI #11327411

Official recalls

16V352000 · Air Bags:frontal:passenger Side:inflator Module

May 24, 2016

Chrysler (FCA US LLC) expanded the affected population to include 73,712 2005-2009 RAM 2500 trucks produced at the St. Louis North Assembly Plant. With this change, Chrysler is recalling certain model year 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2010 RAM 3500 Cab Chassis, 2008-2010 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2012 Jeep Wrangler, 2008-2012 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2012 Chrysler 300, 2006-2012 Dodge Charger, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AL, CA, FL, GA, HI, LA, MS, SC, TX, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Chrysler is also recalling 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2009 RAM 3500 Cab Chassis, 2008-2009 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2009 Jeep Wrangler, 2008-2009 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2009 Chrysler 300, 2006-2009 Dodge Charger, 2005-2009 Dodge Dakota and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AZ, AR, DE, Washington D.C., IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV, or "Zone B." Lastly, unless included in "Zone A" or "Zone B" above, Chrysler is recalling certain 2005-2008 RAM 2500, 2006-2008 RAM 3500, 2007-2008 RAM 3500 Cab Chassis, 2008 RAM 4500 and 5500 Cab Chassis, 2004-2008 Dodge Durango, 2007-2008 Chrysler Aspen, 2007-2008 Jeep Wrangler, 2008 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2008 Chrysler 300, 2006-2008 Dodge Charger, 2005-2008 Dodge Dakota, and 2006-2008 Mitsubishi Raider vehicles originally sold, or registered, in AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY.

Consequence & remedy

Consequence: These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. These inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling. An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the Chrysler, Dodge, Jeep and RAM owners. Mitsubishi owners will be notified by their company. Dealers will replace the passenger frontal air bag inflator, free of charge. The recall began on March 27, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S43. Note: This recall supersedes recall 14V-7700.

15V313000 · Air Bags:frontal:driver Side:inflator Module

May 26, 2015

Chrysler (FCA US LLC) is recalling certain model year 2005-2009 Dodge Ram 2500, 2004-2008 Dodge Ram 1500 and Durango, 2006-2009 Dodge Ram 3500, 2008-2010 Dodge Ram 4500 and 5500, 2007-2008 Chrysler Aspen, 2005-2010 Chrysler 300, 300C, 300S, and SRT8, 2006-2010 Dodge Charger, 2005-2008 Magnum, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles. The affected vehicles are equipped with a dual-stage driver frontal air bag that may be susceptible to moisture intrusion which, over time, could cause the inflator to rupture.

Consequence & remedy

Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the affected Chrysler and Dodge owners and Mitsubishi will notify the affected Raider owners. Dealers will replace the driver's frontal air bag inflator, free of charge. The recall began for Chrylser on June 8, 2015. The recall for Mitsubishi started on June 24, 2015. Chrysler and Dodge owners may contact Chrysler customer service at 1-800-853-1403. Mitsubishi owners may call 1-888-648-7820. Chrysler's number for this recall is R25. Note: This recall supersedes recall 14V817 in its entirety. Vehicles that have had their driver side frontal air bag replaced previously need to have their air bag replaced under this recall as well.

13V528000 · Steering:linkages:tie Rod Assembly

Nov 6, 2013

Chrysler Group LLC (Chrysler) is recalling certain model year 2003-2008 Dodge RAM 2500 4x4 and 3500 4x4, model year 2007-2008 Dodge RAM 3500 4x2 Cab Chassis and model year 2006-2008 Dodge RAM 1500 Mega Cab 4x4 trucks manufactured February 12, 2002, through February 13, 2008. The left tie rod assembly may break.

Consequence & remedy

Consequence: A failure of the tie rod assembly may result in a loss of steering control, increasing the risk of a crash.

Remedy: Chrysler notified owners and launched its recall campaign in January 2014. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N62.

13V529000 · Steering:linkages:tie Rod Assembly

Nov 6, 2013

Chrysler Group LLC (Chrysler) is recalling certain model year 2008-2012 RAM 2500 4X4 and 3500 4X4 trucks, 2008-2012 Dodge RAM 3500 4x2 Cab Chassis, and model year 2008 Dodge RAM 1500 Mega Cab 4x4. The left tie rod assembly may break.

Consequence & remedy

Consequence: A failure of the tie rod assembly may result in a loss of steering control, increasing the risk of a crash.

Remedy: Chrysler notified owners on January 16, 2014 that dealers would inspect vehicles and replace the steering linkage assembly, if necessary. On or about February 27, 2014, Chrysler ceased its recall remedy program due to parts quality concerns, and then re-initiated it on or about April 14, 2014. In July 2015, and under a consent order with NHTSA, the company agreed to offer owners three options for remedying their vehicles: perform the original remedy, offer to repurchase the vehicle at the fair market value plus 10%, or offer an additional incentive offer towards the purchase of a new Dodge, Jeep, Chrysler, or Fiat vehicle. Chrysler will notify owners of the new recall options in a letter expected to be mailed on August 31, 2015. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N49.

11V350000 · Steering:linkages:tie Rod Assembly

Jul 6, 2011

CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2008-2011 DODGE RAM 2500/3500 4X4, MANUFACTURED FROM FEBRUARY 14, 2008, THROUGH MARCH 28, 2011; MODEL YEAR 2008-2011 DODGE RAM 3500 CAB CHASSIS 4X2, MANUFACTURED FROM FEBRUARY 14, 2008, THROUGH MARCH 28, 2011; AND MODEL YEAR 2008 DODGE RAM 1500 MEGA CAB 4X4, MANUFACTURED FROM FEBRUARY 14, 2008, THROUGH AUGUST 15, 2008, BECAUSE THE LEFT TIE ROD BALL STUD MAY FRACTURE. THIS CONDITION TENDS TO OCCUR DURING LOW SPEED PARKING LOT TYPE MANEUVERS WHEN THE CUSTOMER IS MAKING A TIGHT TURN. ADDITIONALLY, MODEL YEAR 2003-2008 DODGE RAM 2500/3500 VEHICLES MAY HAVE RECEIVED THE AFFECTED TIE ROD ASSEMBLY AS A REPLACEMENT PART DURING NORMAL SERVICE.

Consequence & remedy

Consequence: THIS CONDITION COULD RESULT IN THE POTENTIAL LOSS OF DIRECTIONAL STABILITY IN THE LEFT HAND FRONT WHEEL, INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL INSPECT THE TIE ROD ENDS FOR RELATIVE ORIENTATION AND REPLACE THE LEFT OUTER TIE ROD AS REQUIRED AND PERFORM A FRONT END TOE ALIGNMENT AS NEEDED. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON OCTOBER 3, 2011. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

Air Bags:frontal:passenger Side:inflator Module

AQ14003 · Chrysler's Execution Of 13V-528 & 529

Opened Oct 20, 2014 · Closed May 16, 2016

Status: closed (inferred from source dates) · Steering:linkages:tie Rod Assembly

RMD opened this audit query (AQ) investigation in order to better understand and evaluate Chrysler's process(es) for timely and efficient execution of its safety recall campaigns, including its oversight and management of its parts division Mopar.Prior to opening this investigation, RMD had raised concerns with the company related to its execution of two safety recalls, 13V-528 and 13V-529, both of which involved safety defects that could cause the involved vehicles, FCA?s heavier Dodge Ram trucks, to lose steering control suddenly and without warning.Specifically, RMD inquired about the availability of parts for recall repairs, by email and phone on January 15, 2014 and February 19, 2014, due to the volume of complaints it was receiving from owners alleging parts scarcity and parts restrictions. FCA steadfastly denied it had placed parts restrictions on its dealers to manage issues of parts scarcity.FCA shared material showing it had uncommitted stock of parts available for its dealers. Nevertheless, consumer complaints of lack of parts continued.RMD made independent inquiries tosome dealers tobetter understand the conflicting claims between owners alleging lack of ability to repair their defective vehicles due to lack of parts, and FCA?s information showing availability of parts.Dealers informed and provided documentation to RMD on February 21, 2014 and February 25, 2014 showing FCA had, in fact, put into place parts restrictions and, further, had in some instances canceled dealerships? back orders for parts.In addition, during the course of its dialogue with dealers, RMD discovered that FCA had notified their dealerships on February 27, 2014 to return the recall remedy parts over quality concerns, and had therefore effectively canceled its safety recall program without notification to NHTSA. RMD issued a request for information (IR) on October 21, 2014.The company failed to respond to a number of the questions RMD asked that required it to produce specifics surrounding the repairs and parts ordering process with the recalls, including a question about whether a dealer order for recall parts could be canceled and under what circumstances.