Air Bags. Review the 165 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Steering. Review the 103 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Power Train. Review the 73 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

40 crash reports6 fire reports29 injury reports

Electrical System complaints

52 reports

Clear category filter

Mileage unknown · Oct 30, 2023

Electrical SystemUnknown Or Other

Read full complaint

2008 RAM 1500 4 door p/up truck. Factory radio/ . Noise coming from CD player when radio was playing . Saturday morning , radio off . Radio screen lights up like the inside of a bread toaster . Orange Lines appear on the screen. and get hot to the touch . looks like melting wires . I Pulled over and disconnected the battery negative . looked for a Radio fuse in the fuse panel . but was unsuccessful . There was a Burning smell coming from the radio or dashboard still hot to the touch after unsuccessfully locating a Radio Fuse Anywhere . I reconnect the battery negative and noticed the same problem is occurring and then disconnected the negative and Call for assistance . Please help.

NHTSA ODI #11552603

Mileage unknown · Jun 15, 2022

Electrical SystemFire

Vehicle caught fire in drive way while raining seems as though the ac blower resistor caught fire

NHTSA ODI #11469474

Mileage unknown · Oct 10, 2021

Electrical System

COMPUTER SYSTEM FAILED. APPARENTLY AN ELECTRICAL SPIKE OCCURRED AND FRIED THE MOTHERBOARD. AS A RESULT THE VEHICLE BECAME TOTALY INOPERABLE

NHTSA ODI #11436226

145,000 miles · Apr 17, 2020

Electrical System

Read full complaint

TL* THE CONTACT OWNS A 2008 DODGE RAM 1500. CONTACT STATED THAT WHILE DRIVING AT VARIOUS SPEEDS, THE REAR WINDOWS AND REAR DOORS CEASED WITHOUT WARNING. RON TONKIN CHRYSLER JEEP DODGE RAM FIAT (16800 SE MCLOUGHLIN BLVD., MILWAUKIE, OR 97267 (503) 258-5800) WAS CONTACTED AND INFORMED OF THE FAILURE. THE CONTACT WAS INFORMED THAT THE VIN WAS NOT SUBJECTED TO A RECALL. THE VEHICLE WAS THEN TAKEN TO AN INDEPENDENT MECHANIC TO BE DIAGNOSED. THE CONTACT WAS INFORMED THAT THE WIRING HARNESS NEEDED TO BE REPLACED. THE MANUFACTURER WAS CONTACTED AND INFORMED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 145,000.

NHTSA ODI #11321379

152 miles · Feb 3, 2019

Electrical SystemCrash

Read full complaint

MY TRUCK HAS RANDOMLY BEEN MALFUCTIONING FOR ALMOST 2 YEARS, WHILE DRIVING THE POSTED SPEEDS 45-75MPH THE TUCK HAS STALLED OUT CAUSING ME TO LOSE ALL POWER WITH MY INFANT DAUGHTER I HAVE RUN INTO A DITCHED, NEARLY ESCAPED OTHER PASSENGER COLLISONS I HAVE HAD THE INTERIOR LIGHTS AND DASH LIGHTS SHUT OFF WHILE DRIVING AT NIGHT TIME ON NON-LIT ROADS FORCING ME OFF THE ROAD THANKFULLY NO IMJURIES HAVE OCCURIED, IT IS ALL DUE TO A FAULTY TIPM THAT DODGE REFUSES TO ACKNOWLEDGE AND WONT FILE A RECALL YOUR COMPANY CLAIMS THAT THERE IS NO SAFETY DEFECT TO WARRANT A RECALL FROM THE TIPM, BUT HOW MANY PEOPLE WILL HAVE TO DIE FAMILIES AND CHILDREN FOR DODGE TO FIX THE ISSUE, IT IS A HUGE SAFETY ISSUE I WONT PUT MY CHILD BACK IN THE TRUCK AND I WONT DRIVE IT BY MYSELF, ITS ALMOST IMPOSSIBLE TO TO STEER MY VEHICLE WHEN I LOSE ALL POWER WITHOUT WARNING DOING 65MPH HOURS ON A FREEWAY, IT IS BY THE GRACE OF GOD I AM STILL ALIVE AND HAVENT BEEN SERIOUSLY INJURED AND IM NOT WILLING TO KEEP TAKING THE RISKS

NHTSA ODI #11173820

120,000 miles · Nov 3, 2018

Electrical SystemElectronic Stability Control (esc)Fuel/propulsion System

TIMP FAILURE

NHTSA ODI #11145135

64,000 miles · May 25, 2018

Electrical System

Read full complaint

ABOUT 40% OF THE TIME WHEN LOCKING/UNLOCKING THE VEHICLE (EITHER FROM THE DOOR CONTROL SWITCH OR THE REMOTE), THE LOCKING MOTOR CYCLES OVER AND OVER AGAIN. I'VE TAKEN IT TO A COUPLE OF DODGE DEALERSHIPS SERVICE DEPARTMENTS AND HAVE BEEN TOLD THEY CAN'T DUPLICATE THE PROBLEM EVEN THOUGH A TECHNICIAN WAS STANDING RIGHT THERE WHEN IT HAPPENED. I WAS TOLD THIS COULD POTENTIALLY OVERHEAT AND CATCH FIRE! THIS STARTED HAPPENING WITHIN THE FIRST YEAR OF PURCHASING THE VEHICLE NEW.

NHTSA ODI #11098039

45,000 miles · May 25, 2018

Electrical SystemFuel/propulsion System

Read full complaint

AFTER I REFUEL, WHETHER IT'S 10 GAL. OR TOP IT OFF, THE TRUCK WILL STALL EVERYTIME AS I DRIVE JUST THE FIRST SEVERAL MILES(MAYBE AS SOON AS 100 YARDS OR UP TO 10-12 MILES OR SO). IT ONLY HAPPENS WHEN I COME TO A STOP, LIKE AT A RED LIGHT OR AT LOW SPEED MAKING A TURN. IT ALWAYS STARTS BACK UP, NOT ALWAYS EASILY THOUGH. OF COURSE WHEN THIS HAPPENS, POWER BRAKES AND POWER STEERING IS LOST. THIS HAS PUT ME IN A COUPLE OF DANGEROUS SITUATIONS WHILE MAKING A TURN AND SUDDENLY LOSE POWER STEERING. AFTER IT'S STALLED SEVERAL (4-5) TIMES, IT SEEMS TO RECOVER UNTIL I REFUEL AGAIN AND WE START ALL OVER. THIS IS DEFINITELY A MAJOR SAFETY ISSUE AND A RECALL NEEDS TO HAPPEN TO FINALLY FIX THIS RECURRING PROBLEM THAT HAS BEEN HAPPENING FOR SOME TIME NOW. I PURCHASED THIS VEHICLE NEW AND DIDN'T HAVE A PROBLEM FOR THE FIRST 40,000 OR SO MILES. IT NOW HAS 65,000 MILES AND THIS PROBLEM RE-OCCURS WITH EVERY SINGLE REFUEL.

NHTSA ODI #11098037

168,000 miles · May 23, 2018

Electrical System

Read full complaint

DISCOVERED MANUFACTURING DEFECT AT ELECTRICAL PLUG THAT SITS ABOVE LEFT BANK WHERE THE EXHAUST MANIFOLD MEETS THE EXHAUST PIPE. FURTHERMORE, THE CONNECTOR SITS RIGHT BETWEEN THE BLOCK AND THE FIREWALL. THE CONNECTOR AND IT'S WIRING HAVE AN EXTREME TURN OFF OF THE PLUG AND CREATED SUCH TENSION THAT THE PLASTIC CONVOLUTED TUBING WAS PULLED BACK FROM THE WIRING. ALL OF THE WIRING TO APPROXIMATELY 6' BACK FROM THE CONNECTOR IS BARE AND THE WIRES ARE TOUCHING ONE ANOTHER. I FEEL THAT IF THE ROUTE OF THE WIRING HAD LESS OF AN EXTREME BEND AND THERE WAS SOMETHING TO SECURE THE WIRING WAS IN PLACE, THERE WOULDN'T BE THIS CONCERNING ISSUE. I HAVE CONTACTED MY LOCAL DEALERSHIP AND THE FCA AND THEY REFUSE TO LOOK AT IT WITHOUT CHARGING ME MONEY. I AM AN ELECTRICIAN BY TRADE AND I FEAR THAT THIS COULD AFFECT A MULTITUDE OF VEHICLES. THE TRUCK WILL RANDOMLY SHUTDOWN WHILE DRIVING REGARDLESS OF SPEED,, AND WHEN SITTING IDLE AT TIMES. ALSO, THERE ARE TIMES WHEN THE TRANSMISSION FAILS TO REACT TO THE COMMANDS GIVEN WITH THE GEAR SELECTOR. I'M UNSURE WHETHER THIS IS RELATED OR NOT.

NHTSA ODI #11097543

Mileage unknown · Dec 4, 2017

Electrical SystemUnknown Or OtherFire

MY TRUCK CAUGHT ON FIRE IN ENGINE AREA , ENGULFED BACK TO THE BOX WHOLE TRUCK DESTROYED! INSPECTOR NOT KNOW WHAT CAUSED FIRE. TRUCK WAS TOTALED. STATIONARY FOR TWO HOURS AT WORK.

NHTSA ODI #11052147

Official recalls

16V352000 · Air Bags:frontal:passenger Side:inflator Module

May 24, 2016

Chrysler (FCA US LLC) expanded the affected population to include 73,712 2005-2009 RAM 2500 trucks produced at the St. Louis North Assembly Plant. With this change, Chrysler is recalling certain model year 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2010 RAM 3500 Cab Chassis, 2008-2010 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2012 Jeep Wrangler, 2008-2012 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2012 Chrysler 300, 2006-2012 Dodge Charger, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AL, CA, FL, GA, HI, LA, MS, SC, TX, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Chrysler is also recalling 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2009 RAM 3500 Cab Chassis, 2008-2009 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2009 Jeep Wrangler, 2008-2009 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2009 Chrysler 300, 2006-2009 Dodge Charger, 2005-2009 Dodge Dakota and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AZ, AR, DE, Washington D.C., IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV, or "Zone B." Lastly, unless included in "Zone A" or "Zone B" above, Chrysler is recalling certain 2005-2008 RAM 2500, 2006-2008 RAM 3500, 2007-2008 RAM 3500 Cab Chassis, 2008 RAM 4500 and 5500 Cab Chassis, 2004-2008 Dodge Durango, 2007-2008 Chrysler Aspen, 2007-2008 Jeep Wrangler, 2008 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2008 Chrysler 300, 2006-2008 Dodge Charger, 2005-2008 Dodge Dakota, and 2006-2008 Mitsubishi Raider vehicles originally sold, or registered, in AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY.

Consequence & remedy

Consequence: These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. These inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling. An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the Chrysler, Dodge, Jeep and RAM owners. Mitsubishi owners will be notified by their company. Dealers will replace the passenger frontal air bag inflator, free of charge. The recall began on March 27, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S43. Note: This recall supersedes recall 14V-7700.

15V313000 · Air Bags:frontal:driver Side:inflator Module

May 26, 2015

Chrysler (FCA US LLC) is recalling certain model year 2005-2009 Dodge Ram 2500, 2004-2008 Dodge Ram 1500 and Durango, 2006-2009 Dodge Ram 3500, 2008-2010 Dodge Ram 4500 and 5500, 2007-2008 Chrysler Aspen, 2005-2010 Chrysler 300, 300C, 300S, and SRT8, 2006-2010 Dodge Charger, 2005-2008 Magnum, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles. The affected vehicles are equipped with a dual-stage driver frontal air bag that may be susceptible to moisture intrusion which, over time, could cause the inflator to rupture.

Consequence & remedy

Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the affected Chrysler and Dodge owners and Mitsubishi will notify the affected Raider owners. Dealers will replace the driver's frontal air bag inflator, free of charge. The recall began for Chrylser on June 8, 2015. The recall for Mitsubishi started on June 24, 2015. Chrysler and Dodge owners may contact Chrysler customer service at 1-800-853-1403. Mitsubishi owners may call 1-888-648-7820. Chrysler's number for this recall is R25. Note: This recall supersedes recall 14V817 in its entirety. Vehicles that have had their driver side frontal air bag replaced previously need to have their air bag replaced under this recall as well.

13V528000 · Steering:linkages:tie Rod Assembly

Nov 6, 2013

Chrysler Group LLC (Chrysler) is recalling certain model year 2003-2008 Dodge RAM 2500 4x4 and 3500 4x4, model year 2007-2008 Dodge RAM 3500 4x2 Cab Chassis and model year 2006-2008 Dodge RAM 1500 Mega Cab 4x4 trucks manufactured February 12, 2002, through February 13, 2008. The left tie rod assembly may break.

Consequence & remedy

Consequence: A failure of the tie rod assembly may result in a loss of steering control, increasing the risk of a crash.

Remedy: Chrysler notified owners and launched its recall campaign in January 2014. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N62.

13V529000 · Steering:linkages:tie Rod Assembly

Nov 6, 2013

Chrysler Group LLC (Chrysler) is recalling certain model year 2008-2012 RAM 2500 4X4 and 3500 4X4 trucks, 2008-2012 Dodge RAM 3500 4x2 Cab Chassis, and model year 2008 Dodge RAM 1500 Mega Cab 4x4. The left tie rod assembly may break.

Consequence & remedy

Consequence: A failure of the tie rod assembly may result in a loss of steering control, increasing the risk of a crash.

Remedy: Chrysler notified owners on January 16, 2014 that dealers would inspect vehicles and replace the steering linkage assembly, if necessary. On or about February 27, 2014, Chrysler ceased its recall remedy program due to parts quality concerns, and then re-initiated it on or about April 14, 2014. In July 2015, and under a consent order with NHTSA, the company agreed to offer owners three options for remedying their vehicles: perform the original remedy, offer to repurchase the vehicle at the fair market value plus 10%, or offer an additional incentive offer towards the purchase of a new Dodge, Jeep, Chrysler, or Fiat vehicle. Chrysler will notify owners of the new recall options in a letter expected to be mailed on August 31, 2015. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N49.

11V350000 · Steering:linkages:tie Rod Assembly

Jul 6, 2011

CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2008-2011 DODGE RAM 2500/3500 4X4, MANUFACTURED FROM FEBRUARY 14, 2008, THROUGH MARCH 28, 2011; MODEL YEAR 2008-2011 DODGE RAM 3500 CAB CHASSIS 4X2, MANUFACTURED FROM FEBRUARY 14, 2008, THROUGH MARCH 28, 2011; AND MODEL YEAR 2008 DODGE RAM 1500 MEGA CAB 4X4, MANUFACTURED FROM FEBRUARY 14, 2008, THROUGH AUGUST 15, 2008, BECAUSE THE LEFT TIE ROD BALL STUD MAY FRACTURE. THIS CONDITION TENDS TO OCCUR DURING LOW SPEED PARKING LOT TYPE MANEUVERS WHEN THE CUSTOMER IS MAKING A TIGHT TURN. ADDITIONALLY, MODEL YEAR 2003-2008 DODGE RAM 2500/3500 VEHICLES MAY HAVE RECEIVED THE AFFECTED TIE ROD ASSEMBLY AS A REPLACEMENT PART DURING NORMAL SERVICE.

Consequence & remedy

Consequence: THIS CONDITION COULD RESULT IN THE POTENTIAL LOSS OF DIRECTIONAL STABILITY IN THE LEFT HAND FRONT WHEEL, INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL INSPECT THE TIE ROD ENDS FOR RELATIVE ORIENTATION AND REPLACE THE LEFT OUTER TIE ROD AS REQUIRED AND PERFORM A FRONT END TOE ALIGNMENT AS NEEDED. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON OCTOBER 3, 2011. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

Air Bags:frontal:passenger Side:inflator Module

AQ14003 · Chrysler's Execution Of 13V-528 & 529

Opened Oct 20, 2014 · Closed May 16, 2016

Status: closed (inferred from source dates) · Steering:linkages:tie Rod Assembly

RMD opened this audit query (AQ) investigation in order to better understand and evaluate Chrysler's process(es) for timely and efficient execution of its safety recall campaigns, including its oversight and management of its parts division Mopar.Prior to opening this investigation, RMD had raised concerns with the company related to its execution of two safety recalls, 13V-528 and 13V-529, both of which involved safety defects that could cause the involved vehicles, FCA?s heavier Dodge Ram trucks, to lose steering control suddenly and without warning.Specifically, RMD inquired about the availability of parts for recall repairs, by email and phone on January 15, 2014 and February 19, 2014, due to the volume of complaints it was receiving from owners alleging parts scarcity and parts restrictions. FCA steadfastly denied it had placed parts restrictions on its dealers to manage issues of parts scarcity.FCA shared material showing it had uncommitted stock of parts available for its dealers. Nevertheless, consumer complaints of lack of parts continued.RMD made independent inquiries tosome dealers tobetter understand the conflicting claims between owners alleging lack of ability to repair their defective vehicles due to lack of parts, and FCA?s information showing availability of parts.Dealers informed and provided documentation to RMD on February 21, 2014 and February 25, 2014 showing FCA had, in fact, put into place parts restrictions and, further, had in some instances canceled dealerships? back orders for parts.In addition, during the course of its dialogue with dealers, RMD discovered that FCA had notified their dealerships on February 27, 2014 to return the recall remedy parts over quality concerns, and had therefore effectively canceled its safety recall program without notification to NHTSA. RMD issued a request for information (IR) on October 21, 2014.The company failed to respond to a number of the questions RMD asked that required it to produce specifics surrounding the repairs and parts ordering process with the recalls, including a question about whether a dealer order for recall parts could be canceled and under what circumstances.