NHTSA owner reports · September 18, 2026 snapshot.
Exterior Lighting complaints
158 reportsClear category filter50,000 miles · Nov 25, 2013
Electrical SystemExterior Lighting
RIGHT LOW BEAM HAS GONE OUT THREE TIMES OVER THE PAST THREE MONTHS. AFTER FURTHER REVIEW OF THE WIRING CONNECTOR THAT HOLDS THE BULB, THE CONNECTOR IS MELTED AND WILL NO LONGER ILLUMINATE A BULB. AFTER CALLING CHRYSLER'S RECALL TO INQUIRE AS TO IF THEY WILL FIX THE ISSUE, BECAUSE THERE IS A SIMILAR RECALL FOR THE POLICE ONLY M…
Read full complaint
RIGHT LOW BEAM HAS GONE OUT THREE TIMES OVER THE PAST THREE MONTHS. AFTER FURTHER REVIEW OF THE WIRING CONNECTOR THAT HOLDS THE BULB, THE CONNECTOR IS MELTED AND WILL NO LONGER ILLUMINATE A BULB. AFTER CALLING CHRYSLER'S RECALL TO INQUIRE AS TO IF THEY WILL FIX THE ISSUE, BECAUSE THERE IS A SIMILAR RECALL FOR THE POLICE ONLY MODELS, I WAS TOLD NO. I WILL HAVE TO PAY OUT OF POCKET TO HAVE THE ENTIRE HARNESS AND WIRING REPLACED. THIS IS A DESIGN DEFECT THAT CHRYSLER/DODGE WILL NOT TAKE RESPONSIBILITY FOR. DUE TO THE HEADLIGHT BEING OUT, I CAN BARELY DRIVE MY CAR. I AM UNABLE TO DRIVE MY CAR AT NIGHT FOR FEAR OF HAVING NO VISIBILITY OR A COLLISION. THE RECALL THAT WAS SENT WAS M01, HOWEVER CHRYSLER STATES THAT THIS RECALL IS ONLY APPLICABLE TO 2011-2012 POLICE VEHICLES. *TR
NHTSA ODI #10553678
37,345 miles · Nov 20, 2013
Exterior Lighting
MY DRIVER SIDE HEADLIGHT WENT OUT SO I REPLACED BOTH BULBS WITH HID LIGHTS AND THE NEXT DAY THE SAME LIGHT WENT OUT THEN THE OTHER ONE FLICKERED THEN TURNED OFF. I ENDED UP DRIVING HOME USING MY HIGH BEAMS. *TR
NHTSA ODI #10553141
57,617 miles · Nov 14, 2013
Exterior Lighting
TL* THE CONTACT OWNS A 2011 DODGE CHARGER. THE CONTACT STATED THAT WHILE DRIVING APPROXIMATELY 55 MPH, THE PASSENGER'S SIDE HEADLIGHT FAILED. THE CONTACT STATED THAT WHILE CHANGING THE LIGHT BULB, SHE NOTICED THAT THE PASSENGER'S SIDE HEAD LIGHT HARNESS WAS MELTED. THE CONTACTED REPLACED THE LIGHT BULB BUT THE REPAIR DID NOT RE…
Read full complaint
TL* THE CONTACT OWNS A 2011 DODGE CHARGER. THE CONTACT STATED THAT WHILE DRIVING APPROXIMATELY 55 MPH, THE PASSENGER'S SIDE HEADLIGHT FAILED. THE CONTACT STATED THAT WHILE CHANGING THE LIGHT BULB, SHE NOTICED THAT THE PASSENGER'S SIDE HEAD LIGHT HARNESS WAS MELTED. THE CONTACTED REPLACED THE LIGHT BULB BUT THE REPAIR DID NOT REMEDY THE DEFECT. THE CONTACT CALLED THE LOCAL DEALER AND WAS INFORMED THAT THERE WERE NO RECALLS FOR THE VEHICLE. THE CONTACT DID NOT CONTACT THE MANUFACTURER. THE VEHICLE WAS NOT REPAIRED. THE FAILURE MILEAGE WAS 57,617.
NHTSA ODI #10552294
57,000 miles · Nov 12, 2013
Exterior Lighting
STARTED LOW BEAM HEADLIGHT BURNT OUT. REPLACED IT AND IT WENT OUT AGAIN, ONLY TO NOTICE THAT THE HARNESS IS STARTING TO MELT. PRETTY FRUSTRATING. *TR
NHTSA ODI #10551993
40,500 miles · Nov 11, 2013
Electrical SystemExterior Lighting
WIRE HARNESS TO DRIVERS SIDE LOW BEAM HEADLIGHT HAS MELTED. SEEMS LIKE A COMMON PROBLEM W/ THIS MAKE, MODEL, AND YEAR OF THIS VEHICLE. *TR
NHTSA ODI #10551798
Mileage unknown · Nov 6, 2013
Electrical SystemExterior Lighting
MULTIPLE INCIDENTS OF HEADLAMP BURNING OUT IN RAPID SUCCESSION. REPLACED EACH TIME WITH NEW ONLY TO HAPPEN AGAIN. WIRES ON HARNESS FOR HEADLAMP ARE MELTING, CAUSING BURNOUT. DEALER WANTS TO CHARGE TO REPLACE "HEADLAMP ASSEMBLY" (PN 57010411AE/AC/AD), BUT THERE IS A RECALL ON POLICE MODELS FOR THIS EXACT ISSUE UNDER CHRYSLER M…
Read full complaint
MULTIPLE INCIDENTS OF HEADLAMP BURNING OUT IN RAPID SUCCESSION. REPLACED EACH TIME WITH NEW ONLY TO HAPPEN AGAIN. WIRES ON HARNESS FOR HEADLAMP ARE MELTING, CAUSING BURNOUT. DEALER WANTS TO CHARGE TO REPLACE "HEADLAMP ASSEMBLY" (PN 57010411AE/AC/AD), BUT THERE IS A RECALL ON POLICE MODELS FOR THIS EXACT ISSUE UNDER CHRYSLER M01 RECALL/NHTSA RECALL 12V042000. CHRYSLER SAYS RECALL COMPLETE AND REFUSES TO FIX FOR FREE, BUT OBVIOUSLY THOSE PREVIOUSLY RECALLED VEHICLES WEREN'T THE ONLY ONES AFFECTED AS EVIDENCED BY OTHER COMPLAINTS HERE. I SHOULD NOT HAVE TO SPEND NEARLY $500 TO REPAIR A KNOWN ISSUE ON A TWO YEAR OLD VEHICLE. *TR
NHTSA ODI #10551126
Mileage unknown · Oct 27, 2013
Electrical SystemExterior Lighting
LOW BEAM HEADLIGHT WENT OUT. CHANGED IT AND THE VERY NEXT DAY WENT OUT AGAIN. LOOKED TO SEE THE HARNESS WAS BURNT. HIGH BEAMS WORK FINE. CHECKED TO SEE IF IT HAD A RECALL, CHRYSLER SAID NO. WILL BE CONTACTING MY LAWYER SINCE I'VE NOTICED EVERYONE HAS BEEN HAVING THE SAME ISSUE. I THINK EVERY DODGE CHARGER WILL HAVE THIS PROBLEM …
Read full complaint
LOW BEAM HEADLIGHT WENT OUT. CHANGED IT AND THE VERY NEXT DAY WENT OUT AGAIN. LOOKED TO SEE THE HARNESS WAS BURNT. HIGH BEAMS WORK FINE. CHECKED TO SEE IF IT HAD A RECALL, CHRYSLER SAID NO. WILL BE CONTACTING MY LAWYER SINCE I'VE NOTICED EVERYONE HAS BEEN HAVING THE SAME ISSUE. I THINK EVERY DODGE CHARGER WILL HAVE THIS PROBLEM AND THERE ARE TOO MANY FOR THEM TO RECALL, SO THEY ARE GOING TO GET A GANG OF $ OFF OF REPAIRS. *TR
NHTSA ODI #10549717
44,956 miles · Oct 21, 2013
Electrical SystemExterior Lighting
DRIVING HOME FROM SCHOOL WHEN I SMELLED HOT WHAT SEEMED TO BE WIRE COATING MELTING. THE PASSENGER LIGHT WENT OUT, SO I FOUND A PARTS STORE AND PURCHASED A NEW LIGHT PUT IT IN SAW THAT THE WIRING CONNECTOR TO THE LIGHT WAS BLACK AND CRISPY, TOOK NOTE, ONE DAY LATER THE BULB WENT OUT AGAIN, THIS TIME I OPENED THE HOOD LOOKED AT TH…
Read full complaint
DRIVING HOME FROM SCHOOL WHEN I SMELLED HOT WHAT SEEMED TO BE WIRE COATING MELTING. THE PASSENGER LIGHT WENT OUT, SO I FOUND A PARTS STORE AND PURCHASED A NEW LIGHT PUT IT IN SAW THAT THE WIRING CONNECTOR TO THE LIGHT WAS BLACK AND CRISPY, TOOK NOTE, ONE DAY LATER THE BULB WENT OUT AGAIN, THIS TIME I OPENED THE HOOD LOOKED AT THE LIGHT AND IT WAS BURNED TO A CRISP, TOOK THE BULB OUT AND THE WIRE CONNECTION WAS MELTED BEYOND REPAIR AND THE LIGHT CASING WAS COMPLETELY BURNED OUT. THE WIRE CONNECTION HAD BARE WIRE MELTED OUTER INSULATION WAS MELTED RIGHT OFF OF THE WIRE. I TOOK THE BULB OUT AND STARTED LOOKING AT WHY. I AM NOT HAPPY TO SEE THE ISSUE, I HAVE HAD MY NEW TO ME CAR FOR ONLY A MONTH, WILL THIS BE AN EXPENSIVE FIX OR WILL DODGE HELP FIX IT ? *TR
NHTSA ODI #10548827
46,000 miles · Oct 21, 2013
Electrical SystemExterior LightingFire
TL* THE CONTACT OWNS A 2011 DODGE CHARGER. THE CONTACT STATED THAT THE PASSENGER'S SIDE HEADLIGHT STOPPED ILLUMINATING. THE CONTACT REPLACED THE BULB BUT THE FAILURE RECURRED. THE DRIVER'S SIDE HEADLIGHT ALSO STOPPED ILLUMINATING. THE FAILURE RECURRED THREE TIMES. THE VEHICLE WAS TAKEN TO A LOCAL MECHANIC FOR DIAGNOSIS. THE MECH…
Read full complaint
TL* THE CONTACT OWNS A 2011 DODGE CHARGER. THE CONTACT STATED THAT THE PASSENGER'S SIDE HEADLIGHT STOPPED ILLUMINATING. THE CONTACT REPLACED THE BULB BUT THE FAILURE RECURRED. THE DRIVER'S SIDE HEADLIGHT ALSO STOPPED ILLUMINATING. THE FAILURE RECURRED THREE TIMES. THE VEHICLE WAS TAKEN TO A LOCAL MECHANIC FOR DIAGNOSIS. THE MECHANIC STATED THAT THE BULB HARNESS CONNECTOR WAS MELTED. THERE WAS A RECALL UNDER NHTSA CAMPAIGN NUMBER: 12V042000 (ELECTRICAL SYSTEM , EXTERIOR LIGHTING , SERVICE BRAKES, HYDRAULIC) HOWEVER, THE MANUFACTURER ADVISED THAT THE VIN WAS NOT INCLUDED IN THE RECALL. THE VEHICLE WAS NOT REPAIRED. THE APPROXIMATE FAILURE MILEAGE WAS 46,000.
NHTSA ODI #10548793
55,000 miles · Oct 9, 2013
Electrical SystemExterior Lighting
BACKING OUT OF THE DRIVEWAY AND NOTICED DRIVER SIDE LOW BEAM WAS OUT. TOOK IT TO THE DEALERSHIP AND THEY TOLD ME TO REPLACE THE BULB. BOUGHT THE BULB AND APPROX. 4 DAYS LATER LOW BEAM WAS OUT AGAIN ALONG WITH THE A/C GOING IN AND OUT. TOOK IT BACK AND WAS TOLD THIS TIME THAT IT WAS FAULTY WIRING IN THE HARNESS AND NEEDED TO BE R…
Read full complaint
BACKING OUT OF THE DRIVEWAY AND NOTICED DRIVER SIDE LOW BEAM WAS OUT. TOOK IT TO THE DEALERSHIP AND THEY TOLD ME TO REPLACE THE BULB. BOUGHT THE BULB AND APPROX. 4 DAYS LATER LOW BEAM WAS OUT AGAIN ALONG WITH THE A/C GOING IN AND OUT. TOOK IT BACK AND WAS TOLD THIS TIME THAT IT WAS FAULTY WIRING IN THE HARNESS AND NEEDED TO BE REPLACED BECAUSE IT HAD MELTED, WHICH IS THE SAME ISSUE THAT WAS REPAIRED IN JUNE 2012 DUE TO THE RECALL. REPLACED THE HARNESS AND ON THE SAME DAY OF PAYMENT AND RETRIEVING THE CAR, THE PASSENGER SIDE FOG LIGHT WAS OUT. OBVIOUSLY BY THIS POINT I WAS EXTREMELY DISAPPOINTED WITH THIS PROBLEM AS THIS WAS THE 4TH VISIT. TOOK IT BACK A 5TH TIME FOR THE FOG LIGHT. THEY REPLACED THE BULB AND AFTER 2 DAYS THE OTHER FOG LIGHT SHORTED OUT. ABSOLUTELY FED UP WITH THE PROBLEM I DECIDED TO TAKE THE CAR TO A DIFFERENT DODGE DEALERSHIP. UPON DIAGNOSTIC I'M TOLD THAT MY POWER DISTRIBUTION CENTER IS MELTED AND FUSES ARE CRACKED HENCE THE PROBLEM WITH THE A/C AND FOG LIGHTS SHORTING OUT. I'VE RESEARCHED THE PROBLEMS I'M HAVING WITH THE CAR ONLY TO FIND OUT THAT IT IS A COMMON THEME AMONGST THE SAME YEAR MODEL OF MY CAR AND WAS EVEN TOLD BY THE DEALERSHIP THAT THE PROBLEMS WERE ONLY RECALLED IN POLICE VEHICLES UNDER CODE M01. I WAS ALSO TOLD THAT IF THE PROBLEM ISN'T FIXED IT COULD LEAD TO THE VEHICLE BEING COMPLETELY UNABLE TO START. AFTER DEALING WITH HEADQUARTERS AND 2 DEALERSHIPS I'M BEING TOLD THAT I'M OUT OF WARRANTY AT 55,000 MILES AND THE REPAIR IS $984. THE DEALER CAME BACK WITH A GOODWILL OFFER OF $500 THAT IS ONLY VALID FOR 30 DAYS. TO ME THIS IS AN ADMISSION OF GUILT YET THEY STILL DO NOT WANT TO REPAIR AND I'M LEFT DRIVING IN AN UNSAFE VEHICLE. CORPORATE CHRYSLER TOLD ME THAT THE PROBLEMS I'M HAVING DO FIT THE PARAMETERS OF RECALL M01 BUT SINCE MY VEHICLE IS NOT ON THE LIST, I CANNOT BE HELPED. WHAT DOES THAT TELL YOU? *TR
NHTSA ODI #10547465
Official recalls
11Jan 15, 2019
Chrysler (FCA US LLC) is recalling certain 2010 Dodge Ram 3500, Ram 4500/5500, 2010-2011 Dodge Dakota, 2010-2014 Dodge Challenger, 2010-2015 Dodge Challenger, Chrysler 300, and 2010-2016 Jeep Wrangler vehicles. Upon deployment of the driver's frontal air bag, excessive internal pressure may cause the inflator to explode.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the passenger's frontal air bag, the inflator could explode with metal fragments striking the vehicle occupants potentially resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began February 4, 2019. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is V01.
Jan 9, 2018
Chrysler (FCA US LLC) is recalling certain 2009-2013 Jeep Wrangler, Chrysler 300, Dodge Challenger and Dodge Charger vehicles, and 2009-2011 Dodge Dakota vehicles sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, Chrysler is recalling certain 2009-2010 RAM 4500 Cab Chassis, RAM 5500 Cab Chassis, RAM 3500 Cab Chassis, Jeep Wrangler, Chrysler 300, Dodge Dakota, Dodge Challenger, and Dodge Charger vehicles ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Chrysler is also recalling certain 2009 RAM 3500, RAM 2500, RAM 4500 Cab Chassis, RAM 5500 Cab Chassis, Dodge Durango, Chrysler Aspen, RAM 3500 Cab Chassis, Jeep Wrangler, Chrysler 300, Dodge Dakota, Dodge Challenger, and Dodge Charger vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming. In the event of a crash necessitating deployment of the passenger frontal air bag, these passenger air bag inflator may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began February 28, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U03.
Jul 10, 2017
Chrysler (FCA US LLC) is recalling certain model year 2011-2014 Dodge Challenger, Dodge Charger, Chrysler 300, Dodge Durango, and 2012-2014 Jeep Grand Cherokee vehicles. The affected vehicles have electro-hydraulic power steering (EHPS) and are equipped with a 5.7L or a 3.6L engine and a 160, 180 or 220 amp alternator. In the affected vehicles, the alternator may suddenly fail.
Consequence & remedy
Consequence: If the alternator fails, the vehicle may stall without warning, increasing the risk of a crash. There is also the possibility that the alternator may short circuit, increasing the risk of a fire.
Remedy: Chrysler will notify owners, and dealers will inspect the alternator and depending on the part number, will replace the alternator, if necessary, free of charge. The recall began February 12, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T36.
May 24, 2016
Chrysler (FCA US LLC) expanded the affected population to include 73,712 2005-2009 RAM 2500 trucks produced at the St. Louis North Assembly Plant. With this change, Chrysler is recalling certain model year 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2010 RAM 3500 Cab Chassis, 2008-2010 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2012 Jeep Wrangler, 2008-2012 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2012 Chrysler 300, 2006-2012 Dodge Charger, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AL, CA, FL, GA, HI, LA, MS, SC, TX, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Chrysler is also recalling 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2009 RAM 3500 Cab Chassis, 2008-2009 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2009 Jeep Wrangler, 2008-2009 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2009 Chrysler 300, 2006-2009 Dodge Charger, 2005-2009 Dodge Dakota and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AZ, AR, DE, Washington D.C., IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV, or "Zone B." Lastly, unless included in "Zone A" or "Zone B" above, Chrysler is recalling certain 2005-2008 RAM 2500, 2006-2008 RAM 3500, 2007-2008 RAM 3500 Cab Chassis, 2008 RAM 4500 and 5500 Cab Chassis, 2004-2008 Dodge Durango, 2007-2008 Chrysler Aspen, 2007-2008 Jeep Wrangler, 2008 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2008 Chrysler 300, 2006-2008 Dodge Charger, 2005-2008 Dodge Dakota, and 2006-2008 Mitsubishi Raider vehicles originally sold, or registered, in AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY.
Consequence & remedy
Consequence: These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. These inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling. An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the Chrysler, Dodge, Jeep and RAM owners. Mitsubishi owners will be notified by their company. Dealers will replace the passenger frontal air bag inflator, free of charge. The recall began on March 27, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S43. Note: This recall supersedes recall 14V-7700.
Jan 28, 2016
FCA US LLC (Chrysler) is recalling certain model year 2011-2016 Dodge Charger vehicles manufactured August 23, 2010, to January 7, 2016. When an affected vehicle is lifted using the supplied tire jack without chocking the wheels, the vehicle's body-side sill may give causing the tire jack to fail and the car to fall.
Consequence & remedy
Consequence: A car that falls unexpectedly increases the risk of injury.
Remedy: Chrysler will notify owners, and dealers will provide owners with wheel chocks and instructions for their use, free of charge. The recall began on March 21, 2016. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S03.
Jul 27, 2015
Chrysler (FCA US LLC) is recalling certain model year 2011-2014 Dodge Charger vehicles manufactured May 6, 2010, to June 5, 2014. In the affected vehicles, the side impact sensor calibrations may be overly sensitive, and as a result, the side air bag inflatable curtains and seat air bags may unexpectedly deploy and the seat belt pre-tensioners may activate.
Consequence & remedy
Consequence: Air bags that unexpectedly deploy increase the risk of a crash or injury.
Remedy: Chrysler will notify owners, and dealers will update the Occupant Restraint Control module calibration, free of charge. The recall began on August 25, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is R35.
Additional source detail variants (2)
Seat Belts
Chrysler (FCA US LLC) is recalling certain model year 2011-2014 Dodge Charger vehicles manufactured May 6, 2010, to June 5, 2014. In the affected vehicles, the side impact sensor calibrations may be overly sensitive, and as a result, the side air bag inflatable curtains and seat air bags may unexpectedly deploy and the seat belt pre-tensioners may activate.
Consequence: Air bags that unexpectedly deploy increase the risk of a crash or injury.
Remedy: Chrysler will notify owners, and dealers will update the Occupant Restraint Control module calibration, free of charge. The recall began on August 25, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is R35.
Air Bags:side/window
Chrysler (FCA US LLC) is recalling certain model year 2011-2014 Dodge Charger vehicles manufactured May 6, 2010, to June 5, 2014. In the affected vehicles, the side impact sensor calibrations may be overly sensitive, and as a result, the side air bag inflatable curtains and seat air bags may unexpectedly deploy and the seat belt pre-tensioners may activate.
Consequence: Air bags that unexpectedly deploy increase the risk of a crash or injury.
Remedy: Chrysler will notify owners, and dealers will update the Occupant Restraint Control module calibration, free of charge. The recall began on August 25, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is R35.
Oct 8, 2014
Chrysler Group LLC (Chrysler) is recalling certain model year 2011-2014 Chrysler 300, Dodge Charger, Challenger, and Durango; and 2012-2014 Jeep Grand Cherokee vehicles manufactured April 22, 2010, to January 2, 2014, and equipped with a 3.6L engine and a 160 amp alternator. In the affected vehicles, the alternator may suddenly fail.
Consequence & remedy
Consequence: If the alternator fails, the vehicle may stall without warning, increasing the risk of a crash.
Remedy: Chrysler has notified owners, and dealers will replace the alternator, free of charge. The recall began on February 27, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P60.
Mar 4, 2014
Chrysler Group LLC (Chrysler) is recalling certain model year 2011-2012 Dodge Charger vehicles manufactured May 20, 2010, through November 8, 2011, and equipped with halogen headlamps. In the affected vehicles, a sub-harness for the headlights may overheat and cause the low beam headlights to go out.
Consequence & remedy
Consequence: Loss of headlights reduces the driver's visibility, increasing the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will replace the headlamp jumper harnesses and bulbs, or the headlamp assemblies, as necessary, free of charge. The recall began on May 2, 2014. Owners may contract Chrysler at 1-800-853-1403. Chrysler's number associated with this recall is P08. This recall concerns non-police vehicles. A separate campaign was launched in 2012 to address police vehicles. See NHTSA recall 12V-042.
Apr 3, 2013
Chrysler Group LLC (Chrysler) is recalling certain model year 2011-2012 Chrysler 300, Dodge Challenger, and Dodge Charger vehicles manufactured April 11, 2011, through December 14, 2011. The affected vehicles may have improperly sized terminal crimps on the seat side-airbag wiring harness which may cause the seat side-airbags to malfunction and illuminate the airbag warning light.
Consequence & remedy
Consequence: In the event of a crash necessitating airbag deployment the airbags may not operate as designed, increasing the risk of injury.
Remedy: Chrysler will notify owners, and dealers will replace both driver and passenger seat airbag wiring harnesses, free of charge. The recall began on April 22, 2013. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N07.
May 2, 2012
CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2011 AND 2012 300 AND DODGE CHARGER VEHICLES. THESE VEHICLES MAY LOSE ABS/ESC SYSTEM FUNCTION DUE TO AN OVERHEATED POWER DISTRIBUTION CENTER.
Consequence & remedy
Consequence: THIS COULD LEAD TO LOSS OF VEHICLE CONTROL, INCREASING THE RISK OF A CRASH.
Remedy: CHRYSLER WILL NOTIFY OWNERS, AND DEALERS WILL RELOCATE THE ABS/ESC SYSTEM FUSE, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 18, 2012. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.
Additional source detail variants (2)
Electrical System:wiring:fuses And Circuit Breakers
CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2011 AND 2012 300 AND DODGE CHARGER VEHICLES. THESE VEHICLES MAY LOSE ABS/ESC SYSTEM FUNCTION DUE TO AN OVERHEATED POWER DISTRIBUTION CENTER.
Consequence: THIS COULD LEAD TO LOSS OF VEHICLE CONTROL, INCREASING THE RISK OF A CRASH.
Remedy: CHRYSLER WILL NOTIFY OWNERS, AND DEALERS WILL RELOCATE THE ABS/ESC SYSTEM FUSE, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 18, 2012. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.
Service Brakes, Air:antilock:control Unit/module
CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2011 AND 2012 300 AND DODGE CHARGER VEHICLES. THESE VEHICLES MAY LOSE ABS/ESC SYSTEM FUNCTION DUE TO AN OVERHEATED POWER DISTRIBUTION CENTER.
Consequence: THIS COULD LEAD TO LOSS OF VEHICLE CONTROL, INCREASING THE RISK OF A CRASH.
Remedy: CHRYSLER WILL NOTIFY OWNERS, AND DEALERS WILL RELOCATE THE ABS/ESC SYSTEM FUSE, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 18, 2012. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.
Feb 7, 2012
CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2011 and 2012 DODGE CHARGER POLICE VEHICLES. THE LOW BEAM HEADLAMPS OF SOME VEHICLES COULD FAIL DUE TO AN OVERHEATED BULB HARNESS CONNECTOR. OTHER VEHICLES MAY LOSE ABS/ESC SYSTEM FUNCTION DUE TO AN OVERHEATED POWER DISTRIBUTION CENTER.
Consequence & remedy
Consequence: THIS COULD LEAD TO LOSS OF VISIBILITY AND/OR BRAKING ABILITY, INCREASING THE RISK OF A CRASH.
Remedy: CHRYSLER WILL NOTIFY OWNERS AND DEALERS WILL REPLACE THE HEADLAMP JUMPER HARNESSES AND RELOCATE THE ABS/ESC SYSTEM FUSE WITHIN THE POWER DISTRIBUTION CENTER, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON APRIL 2, 2012. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.
Additional source detail variants (4)
Electrical System:wiring:fuses And Circuit Breakers
CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2011 and 2012 DODGE CHARGER POLICE VEHICLES. THE LOW BEAM HEADLAMPS OF SOME VEHICLES COULD FAIL DUE TO AN OVERHEATED BULB HARNESS CONNECTOR. OTHER VEHICLES MAY LOSE ABS/ESC SYSTEM FUNCTION DUE TO AN OVERHEATED POWER DISTRIBUTION CENTER.
Consequence: THIS COULD LEAD TO LOSS OF VISIBILITY AND/OR BRAKING ABILITY, INCREASING THE RISK OF A CRASH.
Remedy: CHRYSLER WILL NOTIFY OWNERS AND DEALERS WILL REPLACE THE HEADLAMP JUMPER HARNESSES AND RELOCATE THE ABS/ESC SYSTEM FUSE WITHIN THE POWER DISTRIBUTION CENTER, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON APRIL 2, 2012. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.
Exterior Lighting:headlights
CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2011 and 2012 DODGE CHARGER POLICE VEHICLES. THE LOW BEAM HEADLAMPS OF SOME VEHICLES COULD FAIL DUE TO AN OVERHEATED BULB HARNESS CONNECTOR. OTHER VEHICLES MAY LOSE ABS/ESC SYSTEM FUNCTION DUE TO AN OVERHEATED POWER DISTRIBUTION CENTER.
Consequence: THIS COULD LEAD TO LOSS OF VISIBILITY AND/OR BRAKING ABILITY, INCREASING THE RISK OF A CRASH.
Remedy: CHRYSLER WILL NOTIFY OWNERS AND DEALERS WILL REPLACE THE HEADLAMP JUMPER HARNESSES AND RELOCATE THE ABS/ESC SYSTEM FUSE WITHIN THE POWER DISTRIBUTION CENTER, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON APRIL 2, 2012. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.
Electrical System:wiring
CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2011 and 2012 DODGE CHARGER POLICE VEHICLES. THE LOW BEAM HEADLAMPS OF SOME VEHICLES COULD FAIL DUE TO AN OVERHEATED BULB HARNESS CONNECTOR. OTHER VEHICLES MAY LOSE ABS/ESC SYSTEM FUNCTION DUE TO AN OVERHEATED POWER DISTRIBUTION CENTER.
Consequence: THIS COULD LEAD TO LOSS OF VISIBILITY AND/OR BRAKING ABILITY, INCREASING THE RISK OF A CRASH.
Remedy: CHRYSLER WILL NOTIFY OWNERS AND DEALERS WILL REPLACE THE HEADLAMP JUMPER HARNESSES AND RELOCATE THE ABS/ESC SYSTEM FUSE WITHIN THE POWER DISTRIBUTION CENTER, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON APRIL 2, 2012. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.
Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:control Unit/module
CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2011 and 2012 DODGE CHARGER POLICE VEHICLES. THE LOW BEAM HEADLAMPS OF SOME VEHICLES COULD FAIL DUE TO AN OVERHEATED BULB HARNESS CONNECTOR. OTHER VEHICLES MAY LOSE ABS/ESC SYSTEM FUNCTION DUE TO AN OVERHEATED POWER DISTRIBUTION CENTER.
Consequence: THIS COULD LEAD TO LOSS OF VISIBILITY AND/OR BRAKING ABILITY, INCREASING THE RISK OF A CRASH.
Remedy: CHRYSLER WILL NOTIFY OWNERS AND DEALERS WILL REPLACE THE HEADLAMP JUMPER HARNESSES AND RELOCATE THE ABS/ESC SYSTEM FUSE WITHIN THE POWER DISTRIBUTION CENTER, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON APRIL 2, 2012. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
PE14022 · Alternator Failure
Opened Jul 22, 2014 · Closed Nov 6, 2014
Status: closed (inferred from source dates) · Electrical System:alternator/generator/regulator
On July 22, 2014, the Office of Defects Investigation (ODI) opened PE14-022 to investigate 14 complaints (VOQs) alleging incidents of alternator failure resulting in engine stall while driving in model year (MY) 2011 through 2012 Dodge Charger vehicles.The MY 2011 through 2012 Dodge Charger vehicles were sold with three different engine options:1) 3.6L V6 (VIN8 = G), 88,766 vehicles; 2) 5.7L V8 (VIN8 = T), 38,615 vehicles; and 3) 6.4L V8 (VIN8 = J), 2,406 MY 2012 vehicles.The 14 VOQs identified in the PE14-022 opening resume involve 13 vehicles with 3.6L V6 engines and 1 vehicle with unknown engine (no VIN provided).In an October 7, 2014 letter to NHTSA, Chrysler described a safety defect condition that could result in rapid alternator failure having limited or no detection in approximately 434,581 MY 2011 through 2014 Chrysler 300, Dodge Charger, Dodge Challenger, Dodge Durango and Jeep Grand Cherokee vehicles equipped with 3.6L engines and 160 amp alternators (NHTSA Recall No. 14V-634, Chrysler P60).The subject alternators are used in vehicles equipped with 3.6L V6 engines and without towing packages.According to Chrysler, the silicone diodes in the alternator rectifier bridge may experience thermal fatigue due to cyclic loading from the Electric Hydraulic Power Steering (EHPS) system, eventually resulting in no output, reduced output, or a fully shorted to ground condition.These failure modes vary in their time to failure and warning to the driver.Depending on the failure mode and timing, system voltage may drop to critically low levels, disabling systems such as the Anti-lock Brake System/Electronic Stability Control, Engine Control Module/Central Body Controller, or a total vehicle electrical system shut down (in the event of a short to ground failure mode).Analysis of complaints to ODI and Chrysler identified a total of 146 incidents of alternator failure resulting in engine stall while driving in MY 2011 through 2012 Dodge Charger vehicles, including 142 involving vehicles equipped with the 3.6L V6 engines (1.6 IPTV) that were included in 14V-634 and 4 involving vehicles with 5.7L V8 engines (0.1 IPTV), which are equipped with different alternators.Analysis of all alternator failure complaints found that approximately 48 percent of VOQs and 21 percent of Chrysler complaints involved allegations of engine stall.Many (98) complaints reported fire and/or smoke, but analysis of these determined that they involved thermal damage to the alternator diode and did not identify any incidents involving damage beyond the alternator assembly.One VOQ identified in the opening resume for PE14-022 alleged a crash, but further evaluation determined that this involved a minor rear-end impact with slight bumper damage.This investigation is closed based on Chrysler's decision to conduct a safety recall.The VOQs associated with this investigation are:10641479,10641366,10641349,10642017,10640770,10640687,10640553,10639692,10638810,10638356,10638175,10638143,10637460,10633806,10633304,10632943,10632006,10631704,10631613,10631420,10631088,10630991,10630854,10630844,10630108,10629623,10629603,10628228,10628150,10627941,10627342,10626452,10626254,10625962,10622385,10622340,10621603,10620961,10619481,10618950,10618948,10618539,10618476,10618334,10618081,10618107,10616834,10616461,10616456,10615754,10615719,10606580,10605090,10604958,10597295,10592085,10588675,10587141,10562463,10559730,10511407
Illustration