← New search

2009 Dodge Charger

Owner reports · Recalls · Investigations

Limited comparison data

There is not enough comparable history to draw a useful model-year comparison.

About this comparison →

When problems were reported

Mileage at the reported incident

124 reports with mileage · 50 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Air Bags. Review the 45 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Electrical System. Review the 45 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Engine. Review the 32 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

9 crash reports4 fire reports8 injury reports

Steering complaints

18 reports
Clear category filter
119,000 miles · Apr 16, 2021
Power TrainSteeringSuspension

I HAVE REPAIRED THE ENTIRE FRONT SUSPENSION SYSTEM, BRAKE SYSTEM, SWAY BAR BUSHING, WATER PUMP, ETC. NOW THE HEAD GASKETS BLEW... ARE THERE ANY RECALLS OR WAYS YOU CAN REFUND ME?

NHTSA ODI #11408359

142,000 miles · Jan 4, 2021
Service BrakesSteering

I HAVE BEEN CHASING A ABS/EPS LIGHT ISSUE SINCE THE DEALERSHIP DID AN AIRBAG RECALL. REPLACED ALL WHEEL SENSORS, ROTORS, BRAKE PADS, CALIPERS AND FINALLY RETURNED TO THE DEALERSHIP FOR THEM TO REPLACE THE ANGLE SENSOR. 5 MINUTES AFTER LEAVING THE LIGHT CAME BACK ON. RETURNED AND THEY SAID THE STEERING COLUMN MEASURED 37MM INSTEA…

Read full complaint

I HAVE BEEN CHASING A ABS/EPS LIGHT ISSUE SINCE THE DEALERSHIP DID AN AIRBAG RECALL. REPLACED ALL WHEEL SENSORS, ROTORS, BRAKE PADS, CALIPERS AND FINALLY RETURNED TO THE DEALERSHIP FOR THEM TO REPLACE THE ANGLE SENSOR. 5 MINUTES AFTER LEAVING THE LIGHT CAME BACK ON. RETURNED AND THEY SAID THE STEERING COLUMN MEASURED 37MM INSTEAD OF 34MM. THIS ITEM HAS NEVER BEEN REPLACED OR DAMAGED AND WITHOUT REPLACING THIS ITEM THEN I'M BEING TOLD THIS SENSOR WILL CONTINUE TO BE AN ISSUE. THIS VEHICLE IS NOT MY DAILY DRIVER BECAUSE I HAVE BEEN CONCERNED ON SAFETY ISSUES. NOW I KNOW IT WAS A MANUFACTURE ISSUE. CHRYSLER REFUSES TO HELP ME BECAUSE THEY STATED THE DEALER HAS NOT DETERMINED THIS TO BE A MANUFACTURER DEFECT. IN 2010 AND 2012 THIS ISSUES HAS COME UP IN THE MEDIA AND THE MANUFACTURER WAS PLACED ON NOTICE BUT FAILED TO RECALL BECAUSE NOT ENOUGH CASES WERE LOCATED.

NHTSA ODI #11386429

107,000 miles · Jan 9, 2017
Steering

I WAS DRIVING DOWN A RESIDENTIAL STREET COMING BACK FROM THE GROCERY STORE TRAVELING BETWEEN 25-30 MILES PER HOUR AND HAD TO MAKE A LEFT TURN COMING UP, I PUT ON MY LEFT TURN SIGNAL TO TURN AT AN 4 WAY INTERSECTION AND THE SWITCH WAS HARD TO PUSH DOWN, WHICH NEVER HAPPENED BEFORE. I PROCEEDED IN MAKING MY LEFT TURN AND AS I WAS …

Read full complaint

I WAS DRIVING DOWN A RESIDENTIAL STREET COMING BACK FROM THE GROCERY STORE TRAVELING BETWEEN 25-30 MILES PER HOUR AND HAD TO MAKE A LEFT TURN COMING UP, I PUT ON MY LEFT TURN SIGNAL TO TURN AT AN 4 WAY INTERSECTION AND THE SWITCH WAS HARD TO PUSH DOWN, WHICH NEVER HAPPENED BEFORE. I PROCEEDED IN MAKING MY LEFT TURN AND AS I WAS TURNING I COULD HEAR SOMETHING IN THE STEERING WHEEL POPPING CONSTANTLY AND THE TURN SIGNAL STAYED ON AND THE ESP LIGHT SOUNDED AND THE ORANGE ESP ICON LIGHT APPEARED ON THE DASH. AS I WAS TURNING THE WHEEL BACK TO THE RIGHT, HEARING THE POPPING THE STEERING WHEEL LOCKED UP ON ME AND I COULDN'T TURN THE WHEEL AT ALL. I HAD TO COME TO A STOP, PUT MY HAZARD LIGHTS ON SO TRAFFIC COULD GO AROUND ME. I PUT THE CAR IN PARK AND TRIED TO TURN THE STEERING WHEEL BACK TO THE LEFT THEN BACK TO THE RIGHT AND THE STEERING WHEEL CAME FREE BUT THE STEERING WHEEL YOU COULD STILL HEAR THE POPPING. I PRECEDED TO GO HOME AND THE STEERING WAS OKAY. I CHECKED THE STEERING FLUID AND IT WAS FINE ONCE I GOT HOME. WHEN I USE MY TURN SIGNAL, THE TURN SIGNAL GETS STUCK AND WILL NOT TURN OFF. IF I TRY TO TURN THE SIGNAL OFF BY THE SWITCH IT JUST TURNS ON THE LEFT SIGNAL AND VICE VERSA. I DROVE IT LATER ON THAT DAY AND I DIDN'T HAVE ANY MORE PROBLEMS. I THOUGHT MAYBE IT WAS JUST SOME FLUKE OR ICE STUCK UNDERNEATH THE CAR FROM THE WINTER WEATHER. MY WIFE DROVE TO WORK YESTERDAY AND SHE STATED ON HER WAY HOME SHE TRIED TO MAKE A RIGHT TURN AND USE THE SWITCH TO TURN RIGHT AND IT WAS STIFF LIKE IT DIDN'T WANT TO TURN ON AND SHE PROCEEDED TO TURN RIGHT AND AGAIN THE ESP LIGHT CAME ON AND THE STEERING WHEEL STARTING POPPING AGAIN AND IT GOT STUCK IN HER MAKING A RIGHT TURN. SHE STATED SHE HAD TO TURN IT BACK TO THE LEFT REALLY HARD SO SHE WOULD CAUSE AN ACCIDENT. IS THIS SOMETHING THAT MAY BE A RECALL? ....UPDATED 02/06/17 *BF

NHTSA ODI #10943788

60,000 miles · Oct 7, 2016
Air BagsSteeringTraction Control System

TL* THE CONTACT OWNS A 2009 DODGE CHARGER. THE CONTACT STATED THAT WHILE DRIVING APPROXIMATELY 10 MPH AND MAKING A RIGHT TURN, A POPPING NOISE WAS PRESENT COMING FROM THE STEERING COLUMN BEFORE THE AIR BAG AND TRACTION CONTROL WARNING LIGHTS ILLUMINATED. THE STEERING WHEEL SUDDENLY COULD NOT BE TURNED IN EITHER DIRECTION. THE VE…

Read full complaint

TL* THE CONTACT OWNS A 2009 DODGE CHARGER. THE CONTACT STATED THAT WHILE DRIVING APPROXIMATELY 10 MPH AND MAKING A RIGHT TURN, A POPPING NOISE WAS PRESENT COMING FROM THE STEERING COLUMN BEFORE THE AIR BAG AND TRACTION CONTROL WARNING LIGHTS ILLUMINATED. THE STEERING WHEEL SUDDENLY COULD NOT BE TURNED IN EITHER DIRECTION. THE VEHICLE WAS TAKEN TO THE DEALER WHERE IT WAS DIAGNOSED THAT CLOCK WHEEL NEEDED TO BE REPLACED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS 60,000.

NHTSA ODI #10914408

101,000 miles · Jul 12, 2016
EngineSteering

TL* THE CONTACT OWNS A 2009 DODGE CHARGER. WHILE DRIVING APPROXIMATELY 65 MPH, THE VEHICLE STALLED WITHOUT WARNING. IN ADDITION, THE STEERING WHEEL SEIZED AND WAS DIFFICULT TO MANUVER. THE VEHICLE WAS TOWED TO AN INDEPENDENT MECHANIC WHERE IT WAS DIAGNOSED THAT THE MOTOR NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE M…

Read full complaint

TL* THE CONTACT OWNS A 2009 DODGE CHARGER. WHILE DRIVING APPROXIMATELY 65 MPH, THE VEHICLE STALLED WITHOUT WARNING. IN ADDITION, THE STEERING WHEEL SEIZED AND WAS DIFFICULT TO MANUVER. THE VEHICLE WAS TOWED TO AN INDEPENDENT MECHANIC WHERE IT WAS DIAGNOSED THAT THE MOTOR NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOT MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS 101,000.

NHTSA ODI #10884422

140,000 miles · Apr 1, 2016
Air BagsElectrical SystemSteering

I TOWED TO HOLLYWOOD CHRYSLER JEEP FOR CAR REPAIR. THEY SAID THEY WOULD FIX TAKE CARE OF EVERYTHING. 3/5/16 RECEIVED A PHONE CALL FROM THEM AT ABOUT 2:00 AND WAS TOLD THAT THEY HAD FIXED THE CAR AND ONLY HAD TO REPLACE THE WIRE HARNESS. I ARRIVED AT THERE BETWEEN 3:30-4:00 ON 03/05/2016. I PAID THEY THEN GAVE ME A BUSINESS CARD …

Read full complaint

I TOWED TO HOLLYWOOD CHRYSLER JEEP FOR CAR REPAIR. THEY SAID THEY WOULD FIX TAKE CARE OF EVERYTHING. 3/5/16 RECEIVED A PHONE CALL FROM THEM AT ABOUT 2:00 AND WAS TOLD THAT THEY HAD FIXED THE CAR AND ONLY HAD TO REPLACE THE WIRE HARNESS. I ARRIVED AT THERE BETWEEN 3:30-4:00 ON 03/05/2016. I PAID THEY THEN GAVE ME A BUSINESS CARD FOR L.A. TOWING TOLD ME I WOULD PROBABLY NEED A TOW SOON. THE STEERING WHEEL WAS UPSIDE DOWN WHEN I RECEIVED THE CAR BACK. I STARTED THE CAR IT MADE A GRINDING SOUND AND KEPT CUTTING OFF WHILE I WAS DRIVING FROM STARTER LEFT LOOSE.ASKED WHY THEY DIDN'T FIX IT JUST HAVE IT TOWED BACK WHEN IT BREAKS DOWN AGAIN.ON 03/ 07 THE CAR BROKE DOWN AGAIN COMPLETELY. FROM THE TIME I RECEIVED IT FROM HOLLYWOOD CHRYSLER JEEP THE CAR KEPT CUTTING OFF AT ALMOST EVERY TEN MINUTES. ON 3/7/16 IT WOULDN'T CRANK ANYMORE SO I HAD TO LEAVE THE CAR THERE. IT GOT TOWED ABOUT 4-5 DAYS LATER BY EMS TOWING. IT IS STILL THERE. THE CUSTOMER SERVICE SUPERVISOR HE STATED THAT THEY WERE NOT OBLIGATED TO FIX THE CAR ONLY TO GET IT RUNNING AND THAT'S IT. HE SAID THAT THEY WERE NOT OBLIGATED TO PUT THE STEERING WHEEL ON CORRECTLY EVEN THOUGH THEY PERFORMED THE RECALL. I THEN ASKED HIM TO SHOW ME PROOF OF THE WIRE HARNESS REPLACEMENT AND HE STATED THAT THEY REPAIRED NOT REPLACED THE WIRE HARNESS. I THEN ASKED ABOUT THE ESTIMATE TO SHOW EXACTLY WHAT WAS THE ISSUES BECAUSE THEIR DESCRIPTION OF THE PROBLEM ON THE ESTIMATE PAGE WAS ONLY A REITERATION ON MY OBSERVATION. HE STATED THEY DIDN'T HAVE TO TELL ME WHAT WAS WRONG, ONLY GET THE CAR STARTED THAT'S ALL. HE STATED THAT THEY WERE NOT UNDER ANY OBLIGATION TO FIX WHAT WAS WRONG,THOUGH THE ONLY REASON I TOWED TO THEM WAS TO HAVE IT REPAIRED. ASKED WHY DID HIS MECHANICS LEAVE THE STARTER LOOSE BECAUSE THAT WAS THE MAIN ISSUE THAT I BROUGHT THE CAR THERE FOR. HE SAID YOU DON'T EXPECT FOR US TO FIX THE WHOLE CAR DO YOU.

NHTSA ODI #10852881

57,000 miles · Jan 13, 2016
Steering

POWER STEERING LINE BLEW OUT AT THE CRIMP. LOST ALL POWER STEERING. DAMAGED PUMP. MAJOR SAFETY ISSUE WHILE DRIVING. SECOND LINE TO GO BAD IN 2 YEARS.

NHTSA ODI #10820028

135,930 miles · Jul 31, 2015
Steering

THE COLUMN SHIFTER DISENGAGED WHILE I WAS DRIVING. LUCKILY IT HAPPENED WHILE I WAS PARKING BECAUSE I HAD BOTH MY CHILDREN IN THE CAR WITH ME AT THE MOMENT.

NHTSA ODI #10745390

50,000 miles · Mar 16, 2015
Steering

HAVE A LEAK IN THE POWER STEERING LINE AT THE CRIP. *TR

NHTSA ODI #10694459

113,709 miles · Jan 3, 2015
Electrical SystemService BrakesSteering

I HAVE HAD ANOTHER INCIDENT WHERE THE AUTOMOBILE HAS HAD ANOTHER MECHANICAL MALFUNCTION. I WAS SLOWING DOWN TO TURN AT A STOP LIGHT. IT DIED, RIGHT BEFORE I STARTED MY TURN. THIS IS NOW THE FOURTH INCIDENT WITH THE SAME ISSUE. THANKFULLY I WAS NOT HURT THIS TIME. THOUGH I AM STILL SUFFERING FROM THE INCIDENT FROM DECEMBER 8…

Read full complaint

I HAVE HAD ANOTHER INCIDENT WHERE THE AUTOMOBILE HAS HAD ANOTHER MECHANICAL MALFUNCTION. I WAS SLOWING DOWN TO TURN AT A STOP LIGHT. IT DIED, RIGHT BEFORE I STARTED MY TURN. THIS IS NOW THE FOURTH INCIDENT WITH THE SAME ISSUE. THANKFULLY I WAS NOT HURT THIS TIME. THOUGH I AM STILL SUFFERING FROM THE INCIDENT FROM DECEMBER 8TH. MY DAUGHTER WAS WITH ME AGAIN WHEN THIS INCIDENT OCCURRED. SHE SAID, "MOM THE LIGHT IS GREEN". I SAID, "I KNOW, THE CAR IS DEAD". I WOULD LIKE TO KNOW WHAT IS BEING DONE, BEFORE SOMEONE GETS KILLED. *TR

NHTSA ODI #10669873

Official recalls

6

18V021000 · Air Bags:frontal:passenger Side:inflator Module

Jan 9, 2018

Chrysler (FCA US LLC) is recalling certain 2009-2013 Jeep Wrangler, Chrysler 300, Dodge Challenger and Dodge Charger vehicles, and 2009-2011 Dodge Dakota vehicles sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, Chrysler is recalling certain 2009-2010 RAM 4500 Cab Chassis, RAM 5500 Cab Chassis, RAM 3500 Cab Chassis, Jeep Wrangler, Chrysler 300, Dodge Dakota, Dodge Challenger, and Dodge Charger vehicles ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Chrysler is also recalling certain 2009 RAM 3500, RAM 2500, RAM 4500 Cab Chassis, RAM 5500 Cab Chassis, Dodge Durango, Chrysler Aspen, RAM 3500 Cab Chassis, Jeep Wrangler, Chrysler 300, Dodge Dakota, Dodge Challenger, and Dodge Charger vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming. In the event of a crash necessitating deployment of the passenger frontal air bag, these passenger air bag inflator may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began February 28, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U03.

16V352000 · Air Bags:frontal:passenger Side:inflator Module

May 24, 2016

Chrysler (FCA US LLC) expanded the affected population to include 73,712 2005-2009 RAM 2500 trucks produced at the St. Louis North Assembly Plant. With this change, Chrysler is recalling certain model year 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2010 RAM 3500 Cab Chassis, 2008-2010 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2012 Jeep Wrangler, 2008-2012 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2012 Chrysler 300, 2006-2012 Dodge Charger, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AL, CA, FL, GA, HI, LA, MS, SC, TX, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Chrysler is also recalling 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2009 RAM 3500 Cab Chassis, 2008-2009 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2009 Jeep Wrangler, 2008-2009 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2009 Chrysler 300, 2006-2009 Dodge Charger, 2005-2009 Dodge Dakota and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AZ, AR, DE, Washington D.C., IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV, or "Zone B." Lastly, unless included in "Zone A" or "Zone B" above, Chrysler is recalling certain 2005-2008 RAM 2500, 2006-2008 RAM 3500, 2007-2008 RAM 3500 Cab Chassis, 2008 RAM 4500 and 5500 Cab Chassis, 2004-2008 Dodge Durango, 2007-2008 Chrysler Aspen, 2007-2008 Jeep Wrangler, 2008 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2008 Chrysler 300, 2006-2008 Dodge Charger, 2005-2008 Dodge Dakota, and 2006-2008 Mitsubishi Raider vehicles originally sold, or registered, in AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY.

Consequence & remedy

Consequence: These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. These inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling. An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the Chrysler, Dodge, Jeep and RAM owners. Mitsubishi owners will be notified by their company. Dealers will replace the passenger frontal air bag inflator, free of charge. The recall began on March 27, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S43. Note: This recall supersedes recall 14V-7700.

15V313000 · Air Bags:frontal:driver Side:inflator Module

May 26, 2015

Chrysler (FCA US LLC) is recalling certain model year 2005-2009 Dodge Ram 2500, 2004-2008 Dodge Ram 1500 and Durango, 2006-2009 Dodge Ram 3500, 2008-2010 Dodge Ram 4500 and 5500, 2007-2008 Chrysler Aspen, 2005-2010 Chrysler 300, 300C, 300S, and SRT8, 2006-2010 Dodge Charger, 2005-2008 Magnum, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles. The affected vehicles are equipped with a dual-stage driver frontal air bag that may be susceptible to moisture intrusion which, over time, could cause the inflator to rupture.

Consequence & remedy

Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the affected Chrysler and Dodge owners and Mitsubishi will notify the affected Raider owners. Dealers will replace the driver's frontal air bag inflator, free of charge. The recall began for Chrylser on June 8, 2015. The recall for Mitsubishi started on June 24, 2015. Chrysler and Dodge owners may contact Chrysler customer service at 1-800-853-1403. Mitsubishi owners may call 1-888-648-7820. Chrysler's number for this recall is R25. Note: This recall supersedes recall 14V817 in its entirety. Vehicles that have had their driver side frontal air bag replaced previously need to have their air bag replaced under this recall as well.

09V420000 · Wheels:lugs/nuts/bolts/studs

Oct 29, 2009

CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2009 THROUGH 2010 PASSENGER VEHICLES EQUIPPED WITH REAR WHEEL DRIVE. THESE VEHICLES MAY HAVE BEEN BUILT WITHOUT A FRONT WHEEL SPINDLE NUT.

Consequence & remedy

Consequence: WHILE DRIVING, A TIRE AND WHEEL SEPARATION COULD OCCUR INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL INSPECT THE TIRE AND WHEEL ASSEMBLY AND IF FOUND WITHOUT A SPINDLE NUT IT WILL BE REPAIRED FREE OF CHARGE. THE RECALL BEGAN ON NOVEMBER 2, 2009. OWNERS MAY CONTACT CHRYSLER AT 1-800-835-1403.

08V642000 · Tires:pressure Monitoring And Regulating Systems

Dec 5, 2008

CHRYSLER IS RECALLING 175 MY 2009 DODGE CHARGER, CHALLENGER, AND CHRYSLER 300 VEHICLES. THE TIRE PRESSURE MONITOR (TPM) SENSORS MAY NOT TRANSMIT THE ACTUAL TIRE PRESSURE. THIS COULD RESULT IN THE DRIVER NOT BEING AWARE OF LOW TIRE PRESSURE.

Consequence & remedy

Consequence: OPERATION OF THE VEHICLE WITH LOW TIRE PRESSURE COULD RESULT IN TIRE DAMAGE AND CAUSE A CRASH WITHOUT WARNING.

Remedy: DEALERS WILL REPLACE THE TPM SENSORS. THE RECALL IS EXPECTED TO BEGIN ON FEBRUARY 9, 2009. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.

08V583000 · Power Train:automatic Transmission:lever And Linkage:column Shift

Nov 6, 2008

CHRYSLER IS RECALLING 20,283 MY 2006-2009 CHARGER AND MAGNUM VEHICLES BUILT WITH THE POLICE PACKAGE AND EQUIPPED WITH A COLUMN SHIFTER. THE GEARSHIFT CABLE MAY BECOME DISENGAGED FROM THE STEERING COLUMN MOUNTING BRACKET AND CAUSE AN INCORRECT TRANSMISSION GEARSHIFT POSITION DISPLAY.

Consequence & remedy

Consequence: THIS COULD ALLOW THE VEHICLE TO MOVE IN AN UNEXPECTED DIRECTION STARTLING THE DRIVER, AND CAUSE A CRASH WITHOUT WARNING.

Remedy: DEALERS WILL ADD A REDUNDANT LOCKING MECHANISM TO THE GEARSHIFT CABLE AT THE MOUNTING BRACKET TO ENSURE PROPER RETENTION AND SHIFT LINKAGE FUNCTION. THE RECALL BEGAN ON NOVEMBER 10, 2008. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

2

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

PE08052 · Prndl Misalignment

Opened Sep 2, 2008 · Closed Nov 10, 2008

Status: closed (inferred from source dates) · Power Train:automatic Transmission:lever And Linkage:column Shift

IN A NOVEMBER 5, 2008 LETTER, CHRYSLER SUBMITTED A DEFECT INFORMATION REPORT DESCRIBING A DEFECT CONDITION THAT COULD RESULT IN PRNDL MISALIGNMENT (I.E., INCORRECT GEAR INDICATION) IN APPROXIMATELY 20,300 MODEL YEAR (MY) 2006 THROUGH 2009 DODGE CHARGER AND MAGNUM POLICE VEHICLES BUILT FROM MAY 17, 2005 THROUGH OCTOBER 21, 2008 (NHTSA RECALL NO. 08V-583, CHRYSLER RECALL H37).ACCORDING TO CHRYSLER, THE GEARSHIFT CABLE MAY BECOME DISENGAGED FROM THE STEERING COLUMN MOUNTING BRACKET AND CAUSE AN INCORRECT TRANSMISSION GEARSHIFT POSITION DISPLAY.THIS COULD ALLOW THE VEHICLE TO MOVE INADVERTENTLY AND CAUSE A CRASH WITHOUT WARNING.CHRYSLER DEALERS WILL REMEDY THE DEFECT CONDITION BY INSTALLING A REDUNDANT LOCKING MECHANISM TO THE GEARSHIFT CABLE AND THE MOUNTING BRACKET TO ENSURE PROPER RETENTION AND SHIFT LINKAGE FUNCTION. CHRYSLER USES A UNIQUE COLUMN SHIFTER IN THESE POLICE VEHICLES.AFTER PE08-052 WAS OPENED, CHRYSLER INSPECTED A MY 2009 POLICE VEHICLE AND NOTED THAT THOUGH THE GEARSHIFT CABLE APPEARED FULLY SEATED INTO THE STEERING COLUMN MOUNTING BRACKET, THE CABLE RETENTION FEATURE (LOCKING PIN) WAS NOT FULLY SEATED.CHRYSLER SUBSEQUENTLY DETERMINED THAT IF THE RETENTION FEATURE IS NOT FULLY SEATED, THE CABLE MAY DISENGAGE FROM THE MOUNTING BRACKET, RESULTING IN THE SHIFT LINKAGE SYSTEM NOT FUNCTIONING TO DESIGN INTENT WITH THE POTENTIAL FOR INCORRECT GEAR POSITION INDICATION VIA THE PRNDL DISPLAY.CHYSLER'S INSPECTION OF 59 MY 2009 DODGE CHARGER AND MAGNUM POLICE VEHICLES IN SEPTEMBER AND OCTOBER FOUND 30 WHERE THE GEARSHIFT CABLE WAS NOT FULLY ENGAGED TO THE MOUNTING BRACKET.THERE ARE NO REPORTED CRASHES OR INJURIES RELATED TO THE DEFECT CONDITION TO DATE. THIS INVESTIGATION IS CLOSED.