NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
884 reports160,000 miles · Apr 9, 2016
Power TrainUnknown Or Other
MY SERVICE ENGINE LIGHT CAME ON, TOOK IT TO ADVANCE AUTO AND IT POPPED CODES P2006, P1607, P0722, P0717. I CHANGED ALL CODES EXCEPT P1607 BECAUSE THEY WERE CHEAPER. THE PCM RUNS 299.00 OR MORE AND I CANNOT AFFORD THAT. MY VEHICLE BARELY MADE IT HOME, IT HAD VERY LITTLE POWER. AFTER CHANGING THE SENSORS, IT RUNS SMOOTH UNTIL YOU…
Read full complaint
MY SERVICE ENGINE LIGHT CAME ON, TOOK IT TO ADVANCE AUTO AND IT POPPED CODES P2006, P1607, P0722, P0717. I CHANGED ALL CODES EXCEPT P1607 BECAUSE THEY WERE CHEAPER. THE PCM RUNS 299.00 OR MORE AND I CANNOT AFFORD THAT. MY VEHICLE BARELY MADE IT HOME, IT HAD VERY LITTLE POWER. AFTER CHANGING THE SENSORS, IT RUNS SMOOTH UNTIL YOU PUT IT IN GEAR, (SERVICE LIGHT STILL ON AND BLINKING) THEN IT SHAKES SO BAD AND HAS LIMP POWER. I CANNOT GET BACK TO ADVANCE TO RUN CODES AGAIN AND WOULD LIKE TO KNOW IF I NEED TO RE PROGRAM THE PCM? WHERE CAN I GET THIS DONE? THE NEAREST DODGE DEALER IS IN CROSSVILLE, TN, A 45 MINUTE DRIVE AND I AM SCARED TO DRIVE THIS THING. I SWEAR, I WISH I NEVER WOULD HAVE BOUGHT IT, WORST CAR EVER. PLEASE HELP ME GET THIS RUNNING RIGHT AGAIN, I AM STILL PAYING FOR IT. IT HAS BEEN PARKED SINCE MARCH 2016.
NHTSA ODI #10854577
130,000 miles · Apr 5, 2016
Electrical SystemVehicle Speed ControlVisibility/wiper
TL* THE CONTACT OWNS A 2007 DODGE CALIBER. WHILE DRIVING 25 MPH, THE ACCELERATOR PEDAL BECAME STUCK WITHOUT WARNING. THE CONTACT ALSO MENTIONED THAT THE WINDSHIELD WIPERS, DEFROSTER, AND RADIO BECAME INOPERABLE. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC WHERE THE FAILURE COULD NOT BE DETERMINED. THE VEHICLE WAS NOT REPAIR…
Read full complaint
TL* THE CONTACT OWNS A 2007 DODGE CALIBER. WHILE DRIVING 25 MPH, THE ACCELERATOR PEDAL BECAME STUCK WITHOUT WARNING. THE CONTACT ALSO MENTIONED THAT THE WINDSHIELD WIPERS, DEFROSTER, AND RADIO BECAME INOPERABLE. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC WHERE THE FAILURE COULD NOT BE DETERMINED. THE VEHICLE WAS NOT REPAIRED. THE VIN WAS NOT INCLUDED IN NHTSA CAMPAIGN NUMBER: 10V234000 (VEHICLE SPEED CONTROL). THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS APPROXIMATELY 130,000. UPDATED 05/17/16*LJ THE CONSUMER STATED THE CROSSBAR WAS REPAIRED. *JS
NHTSA ODI #10853634
86,601 miles · Apr 5, 2016
Structure
TL* THE CONTACT OWNS A 2007 DODGE CALIBER. WHILE THE VEHICLE WAS UNDERGOING AN INSPECTION, THE TECHNICIAN NOTICED THAT THE FRONT CROSSMEMBER UNDERNEATH THE VEHICLE WAS CORRODED AND NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 86,601. U…
Read full complaint
TL* THE CONTACT OWNS A 2007 DODGE CALIBER. WHILE THE VEHICLE WAS UNDERGOING AN INSPECTION, THE TECHNICIAN NOTICED THAT THE FRONT CROSSMEMBER UNDERNEATH THE VEHICLE WAS CORRODED AND NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 86,601. UPDATED 05/10/16*LJ THE CONSUMER STATED THE VEHICLE WAS REPAIRED UNDER WARRANTY. UPDATED 12/11/2017*JS
NHTSA ODI #10853622
30,068 miles · Apr 2, 2016
SteeringSuspension
2007 CALIBER. 30,068 MILES ON CAR AND LOWER CONTROL ARMS ARE BAD AND NEED TO BE REPLACED. NOISE IN FRONT END.MECHANIC SAID BORDERLINE FAILURE
NHTSA ODI #10853099
97,000 miles · Apr 2, 2016
SuspensionUnknown Or Other
ENGINE CRADLE COMPLETELY RUSTED. CAR IS NOT DRIVEABLE. TOOK THE CAR IN FOR SERVICE DUE TO EXTREMELY BAD NOISE. WAS SHOWN CONDITION OF ENGINE CRADLE AND BAD STRUTS DUE TO ENGINE CRADLE COMPLETELY RUSTED.
NHTSA ODI #10853062
126,000 miles · Mar 29, 2016
Unknown Or Other
RCVD A LETTER IN 2013 REGARDING FRONT AND REAR CROSS MEMBERS NEEDING AN INSPECTION & POSSIBLE REPAIRS. I DID NOT GET THIS INSPECTED AS RECOMMENDED. I WENT TODAY TO HAVE CAR PRE-INSPECTED FOR PA INSPECTION & WAS TOLD WHAT MECHANIC CALLED FRONT SUB-FRAME WAS RUSTED THROUGH & EXTREMELY WEAK AND THE REAR WASN'T FAR FROM BEING RUST…
Read full complaint
RCVD A LETTER IN 2013 REGARDING FRONT AND REAR CROSS MEMBERS NEEDING AN INSPECTION & POSSIBLE REPAIRS. I DID NOT GET THIS INSPECTED AS RECOMMENDED. I WENT TODAY TO HAVE CAR PRE-INSPECTED FOR PA INSPECTION & WAS TOLD WHAT MECHANIC CALLED FRONT SUB-FRAME WAS RUSTED THROUGH & EXTREMELY WEAK AND THE REAR WASN'T FAR FROM BEING RUSTED THROUGH. ALSO WARNED IF I WAS IN AN ACCIDENT IT WOULD FOLD BECAUSE OF BEING WEAK & MAKES IT DANGEROUS TO DRIVE. CALLED LOCAL DODGE DEALER & DODGE'S CORPORATE CUSTOMER SERVICE & I COULDN'T GET IN TO HAVE DODGE INSPECT FOR 10 DAYS. HOPEFULLY THE "CROSS MEMBERS" & WHAT MY MECHANIC CALLS "SUB-FRAME" IS ALL THE SAME AND IS COVERED UNDER 10 YR EXTENDED WARRANTY. HTTPS://CUSTOMERCONNECT.CUSTHELP.COM/APP/MOBILE/FIAT/B2C_DETAIL/A_ID/24689
NHTSA ODI #10852239
68,000 miles · Mar 21, 2016
Structure
TL* THE CONTACT OWNS A 2007 DODGE CALIBER. WHILE THE VEHICLE WAS UNDERGOING SCHEDULED MAINTENANCE, THE MECHANIC INFORMED THE CONTACT THAT THE FRAME WAS SEVERELY RUSTED AND THE STRUTS COULD NOT BE CHANGED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 68,000.
NHTSA ODI #10850685
62,000 miles · Mar 16, 2016
Exterior Lighting
TL* THE CONTACT OWNS A 2007 DODGE CALIBER. THE CONTACT STATED THAT WHILE DRIVING AT 20 MPH, THE CONTACT NOTICED THAT THE HIGH AND LOW BEAM HEADLIGHTS ON THE PASSENGER'S SIDE OF THE VEHICLE FAILED TO ILLUMINATE. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC, WHO DIAGNOSED THAT THE BULB NEEDED TO BE REPLACED. THE BULB WAS REPLA…
Read full complaint
TL* THE CONTACT OWNS A 2007 DODGE CALIBER. THE CONTACT STATED THAT WHILE DRIVING AT 20 MPH, THE CONTACT NOTICED THAT THE HIGH AND LOW BEAM HEADLIGHTS ON THE PASSENGER'S SIDE OF THE VEHICLE FAILED TO ILLUMINATE. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC, WHO DIAGNOSED THAT THE BULB NEEDED TO BE REPLACED. THE BULB WAS REPLACED. HOWEVER, THE FAILURE RECURRED. THE VEHICLE WAS THEN TAKEN TO A DEALER, WHO DIAGNOSED THAT THE TOTALLY INTEGRATED POWER MODULE (TIPM) NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS 62,000.
NHTSA ODI #10850031
145,000 miles · Mar 14, 2016
Suspension
BOUGHT VEHICLE USED AT 95000 MILES. 2 YEARS LATER AT ABOUT 120000MILES BOTH CONTROL ARMS WERE REPLACED. NEW TIRES INSTALLED AND ALIGNMENT PERFORMED. LESS THAN TWO YEARS AFTER REPLACEMENT, AT ABOUT 145000MILES, CONTROL ARMS AND BALL JOINTS ARE BAD ONCE AGAIN AND NEED TO BE REPLACED. TIRES AS WELL DO NOT LAST MORE THAN A YEAR AND …
Read full complaint
BOUGHT VEHICLE USED AT 95000 MILES. 2 YEARS LATER AT ABOUT 120000MILES BOTH CONTROL ARMS WERE REPLACED. NEW TIRES INSTALLED AND ALIGNMENT PERFORMED. LESS THAN TWO YEARS AFTER REPLACEMENT, AT ABOUT 145000MILES, CONTROL ARMS AND BALL JOINTS ARE BAD ONCE AGAIN AND NEED TO BE REPLACED. TIRES AS WELL DO NOT LAST MORE THAN A YEAR AND A HALF ON THIS VEHICLE.
NHTSA ODI #10846400
Mileage unknown · Feb 29, 2016
Electrical SystemSuspensionVisibility/wiper
TL* THE CONTACT OWNS A 2007 DODGE CALIBER. WHILE DRIVING AT VARIOUS SPEEDS, THE VEHICLE MADE AN ABNORMAL NOISE IN THE FRONT END. THE VEHICLE WAS TAKEN TO THE DEALER WHERE IT WAS DIAGNOSED THAT THE DRIVER AND PASSENGER SIDE BALL JOINTS AND CONTROL ARMS FAILED AND NEEDED TO BE REPAIRED. THE VEHICLE WAS REPAIRED; HOWEVER, THE FAILU…
Read full complaint
TL* THE CONTACT OWNS A 2007 DODGE CALIBER. WHILE DRIVING AT VARIOUS SPEEDS, THE VEHICLE MADE AN ABNORMAL NOISE IN THE FRONT END. THE VEHICLE WAS TAKEN TO THE DEALER WHERE IT WAS DIAGNOSED THAT THE DRIVER AND PASSENGER SIDE BALL JOINTS AND CONTROL ARMS FAILED AND NEEDED TO BE REPAIRED. THE VEHICLE WAS REPAIRED; HOWEVER, THE FAILURE RECURRED. WHILE DRIVING AT VARIOUS SPEEDS, THE WINDSHIELD WIPERS WOULD INDEPENDENTLY ACTIVATE. WHILE DRIVING AT VARIOUS SPEEDS, THE VEHICLE STALLED WITHOUT WARNING. THE VEHICLE WAS TAKEN TO THE DEALER WHERE IT WAS DIAGNOSED THAT THE ALTERNATOR FAILED AND NEEDED TO BE REPLACED. THE VEHICLE WAS REPAIRED. WHILE ATTEMPTING TO START THE VEHICLE, IT FAILED TO START. THE CONTACT STATED THAT THE ELECTRONIC THROTTLE CONTROL WARNING INDICATOR WOULD ILLUMINATE ON THE INSTRUMENT PANEL. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS UNKNOWN.
NHTSA ODI #10838910
Official recalls
4Dec 21, 2017
Chrysler (FCA US LLC) is recalling various Dodge, Chrysler, and RAM vehicles equipped with Kidde Plastic-Handle or Push Button 'Pindicator' Fire Extinguishers. A list of the affected trailer models is available at: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17V824-0103.pdf. These extinguishers may become clogged, preventing the extinguisher from discharging as expected or requiring excessive force to activate the extinguisher. Additionally, in certain models, the nozzle may detach from the valve assembly with enough force that it could cause injury and also render the product inoperable. For a full list of the affected fire extinguisher models visit: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17E062-5427.pdf
Consequence & remedy
Consequence: If the fire extinguisher does not function properly, it can increase the risk of injury in the event of a fire.
Remedy: Chrysler will notify owners instructing them to contact Kidde for a replacement fire extinguisher, free of charge. The recall began February 14, 2018. Owners may contact Chrysler customer service at 1-800-853-1403 or Kidde customer service service toll-free at 1-855-262-3540, or online at www.kidde.com and click on "Product Safety Recall" for more information. Chrysler's number for this recall is T82.
Jun 3, 2010
CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2007 DODGE CALIBER AND JEEP COMPASS PASSENGER VEHICLES MANUFACTURED FROM MARCH 7 THROUGH MAY 19, 2006. THE PIVOT BUSHINGS IN VEHICLES WITH OVERSIZED ACCELERATOR PEDAL BEARING POCKETS MAY BECOME DISLODGED AND POTENTIALLY CAUSE THE ACCELERATOR PEDAL TO BIND OR STICK.
Consequence & remedy
Consequence: SHOULD THE PEDAL BIND OR BECOME STUCK, IT CAN BE OVERCOME BY SMART BRAKES WHICH OVERRIDE THE ACCELERATOR PEDAL IN CERTAIN CONDITIONS.
Remedy: CHRYSLER WILL NOTIFY OWNERS AND DEALERS WILL INSPECT AND REPLACE ALL AFFECTED ACCELERATOR PEDAL ASSEMBLIES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JUNE 29, 2010. OWNERS MAY CONTACT CHRYSLER TOLL-FREE AT 1-800-853-1403.
May 7, 2007
CERTAIN PASSENGER VEHICLES EQUIPPED WITH REAR DISC BRAKES FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD (FMVSS) NO. 135, "LIGHT VEHICLE BRAKE SYSTEMS." THE LENGTH OF THE REAR WHEEL HUB MOUNTING BOLTS MAY PREVENT ACTUATION OF THE PARK BRAKE.
Consequence & remedy
Consequence: THIS COULD ALLOW UNINTENDED MOVEMENT OF THE VEHICLE UNDER CERTAIN CONDITIONS AND CAUSE A CRASH WITHOUT WARNING.
Remedy: DEALERS WILL REPLACE THE REAR WHEEL HUB MOUNTING BOLTS AND REPAIR THE PARK BRAKE FREE OF CHARGE. THE RECALL BEGAN ON MAY 8, 2007. OWNERS MAY CONTACT DAIMLERCHRYSLER AT 1-800-853-1403.
Dec 29, 2006
ON CERTAIN VEHICLES, THE ANTILOCK BRAKE SYSTEM (ABS) CONTROL MODULE SOFTWARE MAY CAUSE THE REAR BRAKES TO LOCK UP DURING CERTAIN BRAKING CONDITIONS.
Consequence & remedy
Consequence: THIS COULD RESULT IN A LOSS OF VEHICLE CONTROL AND CAUSE A CRASH WITHOUT WARNING.
Remedy: DEALERS WILL REPROGRAM THE ABS ELECTRONIC CONTROL UNIT. THE RECALL BEGAN ON FEBRUARY 19, 2007. OWNERS MAY CONTACT DAIMLERCHRYSLER AT 1-800-853-1403.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE10012 · Sticking Accelerator Pedal
Opened Apr 29, 2010 · Closed Aug 26, 2010
Status: closed (inferred from source dates) · Vehicle Speed Control:accelerator Pedal
In their Defect Information Report (DIR) of June 3, 2010, Chrysler Group, LLC (Chrysler) notified NHTSA that it will conduct a safety recall of approximately 25,265 model year 2007 Dodge Caliber vehicles and 71 model year 2007 Jeep Compass vehicles manufactured from March 7, 2006 through May 19, 2006.The recall will remedy a defect in the accelerator pedal assembly (accelerator pedal) of the Electronic Throttle Control (ETC) system that can cause the accelerator pedal to stick in an open position and not return to the idle position when released.As stated in the opening resume, the subject vehicles (Caliber) are equipped with an ETC accelerator pedal manufactured by the CTS Corporation, the same supplier of the ETC accelerator pedal used in the recently recalled Toyota vehicles.The ETC accelerator pedal used in Caliber and Compass vehicles is not the same as those used in the recalled Toyota vehicles.They are of a different design, were manufactured using different tooling, and fail in a different manner.According to Chrysler and CTS, oversized bearing pockets in the ETC accelerator pedal housing of the Caliber and Compass vehicles allows the accelerator pedal pivot shaft bearings to dislodge from the housing.If this occurs, the accelerator pedal can stick in an open position (i.e., fails to return to the closed position) or be slow to return.Chrysler's DIR notes that the subject vehicles are equipped with Smart Brake Technology and contends that the impact of a binding or sticking accelerator pedal can be negated by its Smart Brake system.In Chrysler's view, the system enables the brake pedal input to override the throttle control system and safely depower the vehicle and minimizes the potential for safety consequences resulting from the defect in the accelerator pedal.Further, Chrysler states, as a result of the presence of this technology, Chrysler Group LLC has concluded that the condition described in this report does not present an unreasonable risk to motor vehicle safety.ODI does not concur with Chrysler's position that the Smart Brake technology employed in the subject vehicles eliminates unreasonable risks to safety stemming from the ETC accelerator pedal defect.Aside from the fact that the technology is applicable only to situations where the brake pedal is activated, the Smart Brake system implemented in the subject vehicles will override a stuck throttle under a discrete set of conditions.Because driver behaviors (e.g., kicking at the accelerator pedal to dislodge it, or pumping the brake pedal instead of steady application) may delay or prevent activation of the Smart Brake system in the subject vehicles, ODI believes that this Smart Brake system does not totally eliminate unreasonable risks to safety posed by this defect or the necessity of a safety recall in this case.See Safety Recall file 10V-234 for recall details.
Illustration