NHTSA owner reports · September 18, 2026 snapshot.
Suspension complaints
255 reportsClear category filter50,000 miles · Mar 2, 2011
Suspension
TL* THE CONTACT OWNS A 2007 DODGE CALIBER. THE CONTACT STATED THAT THE VEHICLE WOULD EXHIBIT AN ABNORMAL BANGING WHEN DRIVING AT VARIOUS SPEEDS. THE VEHICLE WAS TAKEN TO A REPAIR FACILITY WHERE THE CONTACT WAS INFORMED THAT THE DRIVER SIDE BALL JOINT WAS DEFECTIVE AND WOULD AT SOME POINT, FAIL. THE BALL JOINT WAS REPLACED. THE C…
Read full complaint
TL* THE CONTACT OWNS A 2007 DODGE CALIBER. THE CONTACT STATED THAT THE VEHICLE WOULD EXHIBIT AN ABNORMAL BANGING WHEN DRIVING AT VARIOUS SPEEDS. THE VEHICLE WAS TAKEN TO A REPAIR FACILITY WHERE THE CONTACT WAS INFORMED THAT THE DRIVER SIDE BALL JOINT WAS DEFECTIVE AND WOULD AT SOME POINT, FAIL. THE BALL JOINT WAS REPLACED. THE CONTACT STATED THAT THE PASSENGER SIDE BALL JOINT THEN FAILED JANUARY 11, 2011. THE CONTACT WAS ABLE TO SECURE AN APPOINTMENT TO HAVE THE PASSENGER SIDE BALL JOINT REPAIRED. THE MANUFACTURER WAS CONTACTED BUT NO ASSISTANCE WAS OFFERED. THE CURRENT MILEAGE WAS 70,000 AND THE FAILURE MILEAGE WAS 50,000.
NHTSA ODI #10386213
Mileage unknown · Feb 28, 2011
SuspensionWheels
TL*THE CONTACTS OWNS A 2007 DODGE CALIBER. THE CONTACT STATED THAT WHILE DRIVING OVER 28 MPH THERE WAS A NOISE IN THE REAR OF THE VEHICLE. THE CONTACT TOOK THE VEHICLE TO THE DEALER AND WAS TOLD THAT THE NOISE CAME FROM THE REAR HUB BEARING, BECAUSE IT WAS WORN OUT. THE DEALER ALSO STATED THAT BOTH THE REAR LOWER CONTROL ARMS WE…
Read full complaint
TL*THE CONTACTS OWNS A 2007 DODGE CALIBER. THE CONTACT STATED THAT WHILE DRIVING OVER 28 MPH THERE WAS A NOISE IN THE REAR OF THE VEHICLE. THE CONTACT TOOK THE VEHICLE TO THE DEALER AND WAS TOLD THAT THE NOISE CAME FROM THE REAR HUB BEARING, BECAUSE IT WAS WORN OUT. THE DEALER ALSO STATED THAT BOTH THE REAR LOWER CONTROL ARMS WERE WORN OUT AS WELL WHICH ALSO CAUSED THE TIRES TO WEAR BECAUSE OF THE REAR HUB FAILURE. THE CONTACT WAS TOLD THAT THE NHTSA CAMPAIGN NUMBER 07V196000 (WHEELS: CAPS/COVER/HUB) WAS RELATED AND COULD CAUSE UNINTENDED MOVEMENT UNDER CERTAIN CONDITIONS; HOWEVER, THE VIN WAS NOT INCLUDED. THE FAILURE MILEAGE WAS UNKNOWN, BUT THE CURRENT MILEAGE WAS 51,250.
NHTSA ODI #10384732
51,236 miles · Feb 26, 2011
EquipmentSuspensionTires
I STARTED TO NOTICE A NOISE COMING FROM THE BACK END OF THE CAR. WE TOOK THE CAR TO CHRSYLER/DODGE DEALER & WAS TOLD THAT WE HAVE TO REPLACE THE FOLLOWING:REAR HUBS, THE RIGHT & LEFT LOWER CONTROL ARMS & REPLACE THE TIRES. WE HAD JUST BROUGHT NEW TIRES IN NOVEMBER 2010 FOR THE WINTER & NOW THEY HAVE TO BE REPLACE AGAIN.CHRYSLER …
Read full complaint
I STARTED TO NOTICE A NOISE COMING FROM THE BACK END OF THE CAR. WE TOOK THE CAR TO CHRSYLER/DODGE DEALER & WAS TOLD THAT WE HAVE TO REPLACE THE FOLLOWING:REAR HUBS, THE RIGHT & LEFT LOWER CONTROL ARMS & REPLACE THE TIRES. WE HAD JUST BROUGHT NEW TIRES IN NOVEMBER 2010 FOR THE WINTER & NOW THEY HAVE TO BE REPLACE AGAIN.CHRYSLER IS PUTTING MY LIFE, MY HUSBAND & MOTHER'S LIFE LINE ON THE LINE. WHY IS IT THAT WHEN THEY HAD THE MAY 2007 RECALL,THIS PROBLEM WAS NOT INCLUDED AND WHY ARE THEY GETTING AWAY WITH MURDER BY PUTTING OUR LIVES IN JEOPARDY. I THOUGHT I PURCHASED A CAR THAT WOULD KEPT ME SAFE. THE ESTIMATED COST THEY QUOTED US $1800.00. CHRYSLER/DODGE SHOULD BE ASHAME OF THEMSELVES. IS PROFIT MORE IMPORTANT TO THEM THAN OUR LIVES. THE CAR IS WORTHLESS & CAN'T AFFORD TO TRADE IT IN EITHER. *TR
NHTSA ODI #10384618
23,000 miles · Feb 14, 2011
SteeringSuspension
TL*THE CONTACT OWNS A 2007 DODGE CALIBER SXT (NA). THE CONTACT STATED THAT AFTER HAVING ROUTINE SERVICE DONE, THE DEALER NOTICED THAT THE TIRES WERE WORN AND THE FRONT OUTER TIE RODS NEEDED TO BE REPLACED. THE VEHICLE WAS REPAIRED. NOW 20,000 MILES LATER AFTER HAVING THE TIRES REPLACED AGAIN, THE DEALER NOTICED THE FRONT INNER T…
Read full complaint
TL*THE CONTACT OWNS A 2007 DODGE CALIBER SXT (NA). THE CONTACT STATED THAT AFTER HAVING ROUTINE SERVICE DONE, THE DEALER NOTICED THAT THE TIRES WERE WORN AND THE FRONT OUTER TIE RODS NEEDED TO BE REPLACED. THE VEHICLE WAS REPAIRED. NOW 20,000 MILES LATER AFTER HAVING THE TIRES REPLACED AGAIN, THE DEALER NOTICED THE FRONT INNER TIE RODS AND BALL JOINTS NEEDED TO BE REPLACED AGAIN, WHICH WERE CAUSING THE TIRES TO WEAR FASTER. THE VEHICLE HAD NOT BEEN REPAIRED. THE FAILURE MILEAGE WAS APPROXIMATELY 23,000. THE VIN WAS UNAVAILABLE.
NHTSA ODI #10382642
Mileage unknown · Feb 2, 2011
Suspension
2007 DODGE CALIBER. CONSUMER WRITES TO EXPRESS THAT HE BELIEVES THERE IS A SERIOUS DESIGN FLAW IN THE VEHICLE. CONSUMER STATES VEHICLE IS NOT CAPABLE OF ALIGNED DUE TO DEFECTIVE FRONT BALL JOINTS *TGW THE CONSUMER WAS INFORMED THE BALL JOINTS WERE DESIGNED WITH A SEALANT WITH NO CAPABLE MEANS TO LUBRICATE THEM AND REPAIR WAS NO…
Read full complaint
2007 DODGE CALIBER. CONSUMER WRITES TO EXPRESS THAT HE BELIEVES THERE IS A SERIOUS DESIGN FLAW IN THE VEHICLE. CONSUMER STATES VEHICLE IS NOT CAPABLE OF ALIGNED DUE TO DEFECTIVE FRONT BALL JOINTS *TGW THE CONSUMER WAS INFORMED THE BALL JOINTS WERE DESIGNED WITH A SEALANT WITH NO CAPABLE MEANS TO LUBRICATE THEM AND REPAIR WAS NOT POSSIBLE. THE REPLACE THEM WOULD COST $750. *JB
NHTSA ODI #10380480
48,000 miles · Jan 29, 2011
Suspension
I AM VERY SAD TO REPORT THAT MY 2007 DODGE CALIBER THAT I HAVE HAD NO TROUBLE WITH EVER, WITH 48,000 MILES ON IT, THE LEFT LOWER BALL JOINT IS SO BAD THAT IT NEEDS TO BE FIXED IMMEDIATELY. I DIDN'T BELIEVE THE DEALER, SO I BROUGHT IT SOMEWHERE ELSE. STILL GOING TO COST $500 TO FIX ONE STUPID LITTLE PART THAT LOOKS LIKE A MANUFAC…
Read full complaint
I AM VERY SAD TO REPORT THAT MY 2007 DODGE CALIBER THAT I HAVE HAD NO TROUBLE WITH EVER, WITH 48,000 MILES ON IT, THE LEFT LOWER BALL JOINT IS SO BAD THAT IT NEEDS TO BE FIXED IMMEDIATELY. I DIDN'T BELIEVE THE DEALER, SO I BROUGHT IT SOMEWHERE ELSE. STILL GOING TO COST $500 TO FIX ONE STUPID LITTLE PART THAT LOOKS LIKE A MANUFACTURE DEFECT. *LN
NHTSA ODI #10379528
50,000 miles · Jan 27, 2011
SuspensionCrash
BALL JOINTS ARE FAILING ON THESE CARS. THIS OCCURRED AROUND 50,000 AND AGAIN AT 100,000. I DRIVE MOSTLY HIGHWAY MILES THEREFORE THESE SHOULD RARELY GO OUT. DODGE DID NOTHING TO CORRECT THIS AND THE COST OF REPAIR IS OVER $1000. *TR
NHTSA ODI #10379367
65,000 miles · Dec 15, 2010
SteeringSuspension
MY 2007 DODGE CALIBER SXT HAVING BALL JOINT/TIE ROD/CONTROL ARM FAILURE AT 64,000 MILES. REPLACEMENT OF ALL PARTS WOULD BE $1000.00. VEHICLE IS ONLY 3 YRS OLD AND HAVE READ NUMEROUS UPON NUMEROUS COMPLAINTS ABOUT THIS AS A SAFETY ISSUE. *TR
NHTSA ODI #10370772
36,000 miles · Nov 4, 2010
SteeringSuspensionTires
I HAD MY CAR IN WITH ANOTHER COMPLAINT, THE TIRE PRESSURE GAUGE WAS LEAKING. WHILE THEY HAD IT ON THE HOIST, THEY TOLD ME THE TIRES WERE WEARING UNEVENLY DUE TO DAMAGE TO THE TIE RODS. I ONLY HAVE 36,000. MILES ON MY CAR AND IT IS A LITTLE OVER THREE YEARS OLD. I AM TRYING TO GET WITH THEIR PAYING FOR AT LEAST PART OF THE $70…
Read full complaint
I HAD MY CAR IN WITH ANOTHER COMPLAINT, THE TIRE PRESSURE GAUGE WAS LEAKING. WHILE THEY HAD IT ON THE HOIST, THEY TOLD ME THE TIRES WERE WEARING UNEVENLY DUE TO DAMAGE TO THE TIE RODS. I ONLY HAVE 36,000. MILES ON MY CAR AND IT IS A LITTLE OVER THREE YEARS OLD. I AM TRYING TO GET WITH THEIR PAYING FOR AT LEAST PART OF THE $700. REPAIR AND COST OF NEW TIRES. *TR
NHTSA ODI #10364100
59,000 miles · Nov 4, 2010
SteeringSuspension
THE BALL JOINTS AND TIE RODS ON 2006 TO CURRENT DODGE CALIBERS. THEY HAVE PREMATURE WEAR WHICH THE COMPANY KNOWS ABOUT. I HAVE RESEARCHED FOR SEVERAL DAYS AND HAVE FOUND HUNDREDS OF COMPLAINTS ON THE BALL JOINTS AND TIE RODS. THEY BEGIN TO FAIL WITH AS LITTLE AS 30,000 MILES ON THE VEHICLE. I HAVE NOT REPAIRED MY VEHICLE YET DUE…
Read full complaint
THE BALL JOINTS AND TIE RODS ON 2006 TO CURRENT DODGE CALIBERS. THEY HAVE PREMATURE WEAR WHICH THE COMPANY KNOWS ABOUT. I HAVE RESEARCHED FOR SEVERAL DAYS AND HAVE FOUND HUNDREDS OF COMPLAINTS ON THE BALL JOINTS AND TIE RODS. THEY BEGIN TO FAIL WITH AS LITTLE AS 30,000 MILES ON THE VEHICLE. I HAVE NOT REPAIRED MY VEHICLE YET DUE TO THE $1000.00 IT WILL COST ONLY TO FAIL AGAIN IN TWO YEARS. IF ONE OF THE TIE RODS BREAK STEERING WILL BE LOST RESULTING IN LOSS OF CONTROL OF THE VEHICLE. *TR
NHTSA ODI #10364029
Official recalls
4Dec 21, 2017
Chrysler (FCA US LLC) is recalling various Dodge, Chrysler, and RAM vehicles equipped with Kidde Plastic-Handle or Push Button 'Pindicator' Fire Extinguishers. A list of the affected trailer models is available at: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17V824-0103.pdf. These extinguishers may become clogged, preventing the extinguisher from discharging as expected or requiring excessive force to activate the extinguisher. Additionally, in certain models, the nozzle may detach from the valve assembly with enough force that it could cause injury and also render the product inoperable. For a full list of the affected fire extinguisher models visit: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17E062-5427.pdf
Consequence & remedy
Consequence: If the fire extinguisher does not function properly, it can increase the risk of injury in the event of a fire.
Remedy: Chrysler will notify owners instructing them to contact Kidde for a replacement fire extinguisher, free of charge. The recall began February 14, 2018. Owners may contact Chrysler customer service at 1-800-853-1403 or Kidde customer service service toll-free at 1-855-262-3540, or online at www.kidde.com and click on "Product Safety Recall" for more information. Chrysler's number for this recall is T82.
Jun 3, 2010
CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2007 DODGE CALIBER AND JEEP COMPASS PASSENGER VEHICLES MANUFACTURED FROM MARCH 7 THROUGH MAY 19, 2006. THE PIVOT BUSHINGS IN VEHICLES WITH OVERSIZED ACCELERATOR PEDAL BEARING POCKETS MAY BECOME DISLODGED AND POTENTIALLY CAUSE THE ACCELERATOR PEDAL TO BIND OR STICK.
Consequence & remedy
Consequence: SHOULD THE PEDAL BIND OR BECOME STUCK, IT CAN BE OVERCOME BY SMART BRAKES WHICH OVERRIDE THE ACCELERATOR PEDAL IN CERTAIN CONDITIONS.
Remedy: CHRYSLER WILL NOTIFY OWNERS AND DEALERS WILL INSPECT AND REPLACE ALL AFFECTED ACCELERATOR PEDAL ASSEMBLIES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JUNE 29, 2010. OWNERS MAY CONTACT CHRYSLER TOLL-FREE AT 1-800-853-1403.
May 7, 2007
CERTAIN PASSENGER VEHICLES EQUIPPED WITH REAR DISC BRAKES FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD (FMVSS) NO. 135, "LIGHT VEHICLE BRAKE SYSTEMS." THE LENGTH OF THE REAR WHEEL HUB MOUNTING BOLTS MAY PREVENT ACTUATION OF THE PARK BRAKE.
Consequence & remedy
Consequence: THIS COULD ALLOW UNINTENDED MOVEMENT OF THE VEHICLE UNDER CERTAIN CONDITIONS AND CAUSE A CRASH WITHOUT WARNING.
Remedy: DEALERS WILL REPLACE THE REAR WHEEL HUB MOUNTING BOLTS AND REPAIR THE PARK BRAKE FREE OF CHARGE. THE RECALL BEGAN ON MAY 8, 2007. OWNERS MAY CONTACT DAIMLERCHRYSLER AT 1-800-853-1403.
Dec 29, 2006
ON CERTAIN VEHICLES, THE ANTILOCK BRAKE SYSTEM (ABS) CONTROL MODULE SOFTWARE MAY CAUSE THE REAR BRAKES TO LOCK UP DURING CERTAIN BRAKING CONDITIONS.
Consequence & remedy
Consequence: THIS COULD RESULT IN A LOSS OF VEHICLE CONTROL AND CAUSE A CRASH WITHOUT WARNING.
Remedy: DEALERS WILL REPROGRAM THE ABS ELECTRONIC CONTROL UNIT. THE RECALL BEGAN ON FEBRUARY 19, 2007. OWNERS MAY CONTACT DAIMLERCHRYSLER AT 1-800-853-1403.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE10012 · Sticking Accelerator Pedal
Opened Apr 29, 2010 · Closed Aug 26, 2010
Status: closed (inferred from source dates) · Vehicle Speed Control:accelerator Pedal
In their Defect Information Report (DIR) of June 3, 2010, Chrysler Group, LLC (Chrysler) notified NHTSA that it will conduct a safety recall of approximately 25,265 model year 2007 Dodge Caliber vehicles and 71 model year 2007 Jeep Compass vehicles manufactured from March 7, 2006 through May 19, 2006.The recall will remedy a defect in the accelerator pedal assembly (accelerator pedal) of the Electronic Throttle Control (ETC) system that can cause the accelerator pedal to stick in an open position and not return to the idle position when released.As stated in the opening resume, the subject vehicles (Caliber) are equipped with an ETC accelerator pedal manufactured by the CTS Corporation, the same supplier of the ETC accelerator pedal used in the recently recalled Toyota vehicles.The ETC accelerator pedal used in Caliber and Compass vehicles is not the same as those used in the recalled Toyota vehicles.They are of a different design, were manufactured using different tooling, and fail in a different manner.According to Chrysler and CTS, oversized bearing pockets in the ETC accelerator pedal housing of the Caliber and Compass vehicles allows the accelerator pedal pivot shaft bearings to dislodge from the housing.If this occurs, the accelerator pedal can stick in an open position (i.e., fails to return to the closed position) or be slow to return.Chrysler's DIR notes that the subject vehicles are equipped with Smart Brake Technology and contends that the impact of a binding or sticking accelerator pedal can be negated by its Smart Brake system.In Chrysler's view, the system enables the brake pedal input to override the throttle control system and safely depower the vehicle and minimizes the potential for safety consequences resulting from the defect in the accelerator pedal.Further, Chrysler states, as a result of the presence of this technology, Chrysler Group LLC has concluded that the condition described in this report does not present an unreasonable risk to motor vehicle safety.ODI does not concur with Chrysler's position that the Smart Brake technology employed in the subject vehicles eliminates unreasonable risks to safety stemming from the ETC accelerator pedal defect.Aside from the fact that the technology is applicable only to situations where the brake pedal is activated, the Smart Brake system implemented in the subject vehicles will override a stuck throttle under a discrete set of conditions.Because driver behaviors (e.g., kicking at the accelerator pedal to dislodge it, or pumping the brake pedal instead of steady application) may delay or prevent activation of the Smart Brake system in the subject vehicles, ODI believes that this Smart Brake system does not totally eliminate unreasonable risks to safety posed by this defect or the necessity of a safety recall in this case.See Safety Recall file 10V-234 for recall details.
Illustration