NHTSA owner reports · September 18, 2026 snapshot.
Structure complaints
158 reportsClear category filter110,000 miles · Jun 30, 2014
StructureSuspension
THE CAR WOULD NOT STEER WITH ANY CONTROLLABILITY. UPON 2 DIFFERENT INDEPENDENT MECHANIC INSPECTIONS WE DISCOVERED THE LOWER BALL JOINT WAS SO WORN/LOOSE IF I HAD CONTINUED TO DRIVE I COULD EASILY HAVE LOST A TIRE. THE ENTIRE UNDERFRAME IS CORRODED AND I WAS TOLD IT WOULD HAVE TO BE REPLACED SOON OR IT WOULD ALSO BECOME A SAFETY …
Read full complaint
THE CAR WOULD NOT STEER WITH ANY CONTROLLABILITY. UPON 2 DIFFERENT INDEPENDENT MECHANIC INSPECTIONS WE DISCOVERED THE LOWER BALL JOINT WAS SO WORN/LOOSE IF I HAD CONTINUED TO DRIVE I COULD EASILY HAVE LOST A TIRE. THE ENTIRE UNDERFRAME IS CORRODED AND I WAS TOLD IT WOULD HAVE TO BE REPLACED SOON OR IT WOULD ALSO BECOME A SAFETY HAZARD IN THE NEAR FUTURE. DODGE HAS TO BE AWARE OF THIS PROBLEM BECAUSE AFTER CONDUCTING SOME RESEARCH ON MY OWN I HAVE FOUND HUNDREDS OF 2007 CALIBER OWNERS WITH ALMOST IDENTICAL ISSUES TO MINE. HOPING NO ONE GETS HURT BEFORE THEY REALIZE WHAT A SERIOUS RISK THIS TYPE OF LOW QUALITY MANUFACTURING IS... *TR
NHTSA ODI #10607175
109,000 miles · Jun 10, 2014
StructureSuspension
JUST FILING A COMPLAINT ABOUT SUBSTANDARD MANUFACTURING OF MY VEHICLE CROSS MEMBER PARTS. SUBSTANDARD MATERIAL WAS USED AND SEVERE CORROSION IS A RESULT. CHRYSLER HAS A RECALL FOR REPAIR. COULD POSE SAFETY ISSUES IF PARTS RUST COMPLETELY THROUGH. *TR
NHTSA ODI #10597427
94,000 miles · May 30, 2014
Structure
TL* THE CONTACT OWNS A 2007 DODGE CALIBER. THE CONTACT STATED THAT WHILE THE VEHICLE BEING SERVICED, THE TECHNICIAN DISCOVERED THAT THE FRONT SECTION OF THE SUB FRAME WAS CORRODED AND RUSTED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS 94,000.
NHTSA ODI #10595229
107,000 miles · May 12, 2014
StructureSuspension
WHEN I WAS DRIVING IN TOWN AT SPEEDS AROUND 25-40 MPH I KEPT HEARING A CLICKING NOISE BENEATH THE DRIVERS SEAT, ESPECIALLY WHEN I MADE TURNS. I TOOK IT TO A SHOP AND THEY LIFTED IT UP. TURNS OUT THE ENTIRE SUSPENSION CARRIAGE WAS RUSTING AND ROTTING. THE CLICKING NOISE I WAS HEARING WAS RUSTY PIECES OF METAL RUBBING AGAINST O…
Read full complaint
WHEN I WAS DRIVING IN TOWN AT SPEEDS AROUND 25-40 MPH I KEPT HEARING A CLICKING NOISE BENEATH THE DRIVERS SEAT, ESPECIALLY WHEN I MADE TURNS. I TOOK IT TO A SHOP AND THEY LIFTED IT UP. TURNS OUT THE ENTIRE SUSPENSION CARRIAGE WAS RUSTING AND ROTTING. THE CLICKING NOISE I WAS HEARING WAS RUSTY PIECES OF METAL RUBBING AGAINST ONE ANOTHER. WE TOOK IT TO A DEALERSHIP AND THEY SAID THAT THE AC CONDENSATE LINE WAS DIRECTED TO THE SUBFRAME/UNDERCARRIAGE OF THE CALIBER. THE WATER WAS POOLING AND CAUSING IT TO RUST. I'M GRATEFUL WE FOUND OUT ABOUT IT WHEN WE DID INSTEAD OF HAVING THE WHOLE BOTTOM OF THE CAR FALL OUT FROM UNDER US WHEN WE WERE GOING AT A HIGH SPEED. THIS SEEMS TO BE HAPPENING TO MANY OF THE DODGE CALIBERS RIGHT AROUND 7 YEARS. WE HAVE PHOTOS OF THE DAMAGE. UNBELIEVABLE. *TR
NHTSA ODI #10587901
64,000 miles · May 9, 2014
StructureSuspension
I NOTICED A PERIODIC CLUNKING SOUND COMING FROM UNDERNEATH. UPON INSPECTION BY THE DEALER, THE K-BAR OR K-FRAME, WHICH IS THE PART THAT HOLDS THE FRONT SUSPENSION TOGETHER, WAS FOUND TO HAVE COMPLETELY RUSTED THROUGH. IT IS COMPLETELY ROTTEN. CHRYSLER WAS CONTACTED AND WILL NOT HELP WITH THUS $1400 REPAIR. THE VEHICLE HAS ONLY 6…
Read full complaint
I NOTICED A PERIODIC CLUNKING SOUND COMING FROM UNDERNEATH. UPON INSPECTION BY THE DEALER, THE K-BAR OR K-FRAME, WHICH IS THE PART THAT HOLDS THE FRONT SUSPENSION TOGETHER, WAS FOUND TO HAVE COMPLETELY RUSTED THROUGH. IT IS COMPLETELY ROTTEN. CHRYSLER WAS CONTACTED AND WILL NOT HELP WITH THUS $1400 REPAIR. THE VEHICLE HAS ONLY 64000 MILES ON IT. I HAVE NEVER HAD TO REPLACE THIS PART IN ANY VEHICLE I HAVE EVER OWNED. THIS IS A SERIOUS SAFETY ISSUE. *TR
NHTSA ODI #10587483
38,595 miles · May 7, 2014
Structure
TL* THE CONTACT OWNS A 2007 DODGE CALIBER. THE CONTACT STATED THAT THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC FOR AN UNRELATED REPAIR WHEN HE NOTICED THAT THE ENTIRE SUB FRAME WAS COMPLETELY CORRODED. THE VEHICLE HAD NOT BEEN REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED OF THE PROBLEM. THE APPROXIMATE FAILURE MILEAGE WAS 88…
Read full complaint
TL* THE CONTACT OWNS A 2007 DODGE CALIBER. THE CONTACT STATED THAT THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC FOR AN UNRELATED REPAIR WHEN HE NOTICED THAT THE ENTIRE SUB FRAME WAS COMPLETELY CORRODED. THE VEHICLE HAD NOT BEEN REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED OF THE PROBLEM. THE APPROXIMATE FAILURE MILEAGE WAS 88,595.
NHTSA ODI #10586975
153,000 miles · Apr 28, 2014
Structure
TL* THE CONTACT OWNS A 2007 DODGE CALIBER. THE CONTACT STATED THAT WHILE HAVING MAINTENANCE PERFORMED, HE WAS NOTIFIED THAT THE ENGINE CRADLE WAS COMPLETELY CORRODED. THE VEHICLE WAS NOT TAKEN TO THE DEALER. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE. THE VEHICLE WAS NOT REPAIRED. THE FAILURE AND CURRENT MILEAGE WAS 153,000.
NHTSA ODI #10585238
100,000 miles · Apr 11, 2014
Structure
TL* THE CONTACT OWNS A 2007 DODGE CALIBER. THE CONTACT STATED THAT THE FRONT AND REAR OF THE SUB FRAME WAS RUSTED. THE VEHICLE WAS TAKEN TO A PRIVATE MECHANIC WHO CONFIRMED THE FAILURE. THE MANUFACTURER WAS NOTIFIED OF THE ISSUE. THE APPROXIMATE FAILURE MILEAGE WAS 100,000.
NHTSA ODI #10579167
85,000 miles · Mar 28, 2014
Structure
TL* THE CONTACT OWNS A 2007 DODGE CALIBER. THE CONTACT STATED THAT WHILE HAVING MAINTENANCE PERFORMED, HE WAS NOTIFIED THAT THE ENGINE CRADLE WAS COMPLETELY CORRODED. THE VEHICLE WAS NOT TAKEN TO THE DEALER. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE. THE VEHICLE WAS NOT REPAIRED. THE FAILURE AND CURRENT MILEAGE WAS 85,000.…
Read full complaint
TL* THE CONTACT OWNS A 2007 DODGE CALIBER. THE CONTACT STATED THAT WHILE HAVING MAINTENANCE PERFORMED, HE WAS NOTIFIED THAT THE ENGINE CRADLE WAS COMPLETELY CORRODED. THE VEHICLE WAS NOT TAKEN TO THE DEALER. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE. THE VEHICLE WAS NOT REPAIRED. THE FAILURE AND CURRENT MILEAGE WAS 85,000.
NHTSA ODI #10575403
120,000 miles · Mar 27, 2014
EngineStructure
I WAS TOLD BY MEINEKE THAT MY ENGINE'S SUBFRAME WAS SO CORRODED THAT THE CAR WAS UNSAFE TO DRIVE. THE MECHANIC TOLD ME THAT IT WAS VERY UNUSUAL FOR A CAR THIS YOUNG TO HAVE A CORRODED SUBFRAME. I LEARNED FROM ONLINE RESEARCH THAT CORRODED SUBFRAMES ARE A FREQUENT COMPLAINT WITH DODGE CALIBERS, POSSIBLY BECAUSE OF THE PLACEMENT…
Read full complaint
I WAS TOLD BY MEINEKE THAT MY ENGINE'S SUBFRAME WAS SO CORRODED THAT THE CAR WAS UNSAFE TO DRIVE. THE MECHANIC TOLD ME THAT IT WAS VERY UNUSUAL FOR A CAR THIS YOUNG TO HAVE A CORRODED SUBFRAME. I LEARNED FROM ONLINE RESEARCH THAT CORRODED SUBFRAMES ARE A FREQUENT COMPLAINT WITH DODGE CALIBERS, POSSIBLY BECAUSE OF THE PLACEMENT OF THE AIR CONDITIONING UNIT. THERE WAS NO RECALL. I IMMEDIATELY REPLACED THE SUBFRAME AT A COST OF APPROXIMATELY $1,000. *TR
NHTSA ODI #10575194
Official recalls
4Dec 21, 2017
Chrysler (FCA US LLC) is recalling various Dodge, Chrysler, and RAM vehicles equipped with Kidde Plastic-Handle or Push Button 'Pindicator' Fire Extinguishers. A list of the affected trailer models is available at: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17V824-0103.pdf. These extinguishers may become clogged, preventing the extinguisher from discharging as expected or requiring excessive force to activate the extinguisher. Additionally, in certain models, the nozzle may detach from the valve assembly with enough force that it could cause injury and also render the product inoperable. For a full list of the affected fire extinguisher models visit: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17E062-5427.pdf
Consequence & remedy
Consequence: If the fire extinguisher does not function properly, it can increase the risk of injury in the event of a fire.
Remedy: Chrysler will notify owners instructing them to contact Kidde for a replacement fire extinguisher, free of charge. The recall began February 14, 2018. Owners may contact Chrysler customer service at 1-800-853-1403 or Kidde customer service service toll-free at 1-855-262-3540, or online at www.kidde.com and click on "Product Safety Recall" for more information. Chrysler's number for this recall is T82.
Jun 3, 2010
CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2007 DODGE CALIBER AND JEEP COMPASS PASSENGER VEHICLES MANUFACTURED FROM MARCH 7 THROUGH MAY 19, 2006. THE PIVOT BUSHINGS IN VEHICLES WITH OVERSIZED ACCELERATOR PEDAL BEARING POCKETS MAY BECOME DISLODGED AND POTENTIALLY CAUSE THE ACCELERATOR PEDAL TO BIND OR STICK.
Consequence & remedy
Consequence: SHOULD THE PEDAL BIND OR BECOME STUCK, IT CAN BE OVERCOME BY SMART BRAKES WHICH OVERRIDE THE ACCELERATOR PEDAL IN CERTAIN CONDITIONS.
Remedy: CHRYSLER WILL NOTIFY OWNERS AND DEALERS WILL INSPECT AND REPLACE ALL AFFECTED ACCELERATOR PEDAL ASSEMBLIES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JUNE 29, 2010. OWNERS MAY CONTACT CHRYSLER TOLL-FREE AT 1-800-853-1403.
May 7, 2007
CERTAIN PASSENGER VEHICLES EQUIPPED WITH REAR DISC BRAKES FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD (FMVSS) NO. 135, "LIGHT VEHICLE BRAKE SYSTEMS." THE LENGTH OF THE REAR WHEEL HUB MOUNTING BOLTS MAY PREVENT ACTUATION OF THE PARK BRAKE.
Consequence & remedy
Consequence: THIS COULD ALLOW UNINTENDED MOVEMENT OF THE VEHICLE UNDER CERTAIN CONDITIONS AND CAUSE A CRASH WITHOUT WARNING.
Remedy: DEALERS WILL REPLACE THE REAR WHEEL HUB MOUNTING BOLTS AND REPAIR THE PARK BRAKE FREE OF CHARGE. THE RECALL BEGAN ON MAY 8, 2007. OWNERS MAY CONTACT DAIMLERCHRYSLER AT 1-800-853-1403.
Dec 29, 2006
ON CERTAIN VEHICLES, THE ANTILOCK BRAKE SYSTEM (ABS) CONTROL MODULE SOFTWARE MAY CAUSE THE REAR BRAKES TO LOCK UP DURING CERTAIN BRAKING CONDITIONS.
Consequence & remedy
Consequence: THIS COULD RESULT IN A LOSS OF VEHICLE CONTROL AND CAUSE A CRASH WITHOUT WARNING.
Remedy: DEALERS WILL REPROGRAM THE ABS ELECTRONIC CONTROL UNIT. THE RECALL BEGAN ON FEBRUARY 19, 2007. OWNERS MAY CONTACT DAIMLERCHRYSLER AT 1-800-853-1403.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE10012 · Sticking Accelerator Pedal
Opened Apr 29, 2010 · Closed Aug 26, 2010
Status: closed (inferred from source dates) · Vehicle Speed Control:accelerator Pedal
In their Defect Information Report (DIR) of June 3, 2010, Chrysler Group, LLC (Chrysler) notified NHTSA that it will conduct a safety recall of approximately 25,265 model year 2007 Dodge Caliber vehicles and 71 model year 2007 Jeep Compass vehicles manufactured from March 7, 2006 through May 19, 2006.The recall will remedy a defect in the accelerator pedal assembly (accelerator pedal) of the Electronic Throttle Control (ETC) system that can cause the accelerator pedal to stick in an open position and not return to the idle position when released.As stated in the opening resume, the subject vehicles (Caliber) are equipped with an ETC accelerator pedal manufactured by the CTS Corporation, the same supplier of the ETC accelerator pedal used in the recently recalled Toyota vehicles.The ETC accelerator pedal used in Caliber and Compass vehicles is not the same as those used in the recalled Toyota vehicles.They are of a different design, were manufactured using different tooling, and fail in a different manner.According to Chrysler and CTS, oversized bearing pockets in the ETC accelerator pedal housing of the Caliber and Compass vehicles allows the accelerator pedal pivot shaft bearings to dislodge from the housing.If this occurs, the accelerator pedal can stick in an open position (i.e., fails to return to the closed position) or be slow to return.Chrysler's DIR notes that the subject vehicles are equipped with Smart Brake Technology and contends that the impact of a binding or sticking accelerator pedal can be negated by its Smart Brake system.In Chrysler's view, the system enables the brake pedal input to override the throttle control system and safely depower the vehicle and minimizes the potential for safety consequences resulting from the defect in the accelerator pedal.Further, Chrysler states, as a result of the presence of this technology, Chrysler Group LLC has concluded that the condition described in this report does not present an unreasonable risk to motor vehicle safety.ODI does not concur with Chrysler's position that the Smart Brake technology employed in the subject vehicles eliminates unreasonable risks to safety stemming from the ETC accelerator pedal defect.Aside from the fact that the technology is applicable only to situations where the brake pedal is activated, the Smart Brake system implemented in the subject vehicles will override a stuck throttle under a discrete set of conditions.Because driver behaviors (e.g., kicking at the accelerator pedal to dislodge it, or pumping the brake pedal instead of steady application) may delay or prevent activation of the Smart Brake system in the subject vehicles, ODI believes that this Smart Brake system does not totally eliminate unreasonable risks to safety posed by this defect or the necessity of a safety recall in this case.See Safety Recall file 10V-234 for recall details.
Illustration