IllustrationDASHBOARD CRACKED BY PASSENGER SIDE AIRBAG AND DRIVER SIDE INSTRUMENT PANEL
2014 Chevrolet Tahoe
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2014 Chevrolet Tahoe do not stand out strongly from the model-year median of 246.
About this comparison →How this year compares
Owner complaints by model year
Compare all Tahoe years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
70–25K
1025–50K
1550–75K
775–100K
7100–150K
1150K+
47 reports with mileage · 43 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Electrical System. Review the 15 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Air Bags. Review the 13 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Structure. Review the 10 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
3 crash reports0 fire reports1 injury reports
What owners actually said
90 reportsTL* THE CONTACT OWNS A 2014 CHEVROLET TAHOE. WHILE DRIVING 55 MPH, THE SUN ROOF ABRUPTLY SHATTERED INTO PIECES. THE VEHICLE WAS DRIVEN TO THE CONTACT'S RESIDENCE. THERE WERE NO INJURIES. THE DEALER AND MANUFACTURER WERE NOT CONTACTED. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE VIN WAS UNKNOWN. THE FAILURE MILEAGE WAS 43,000.…
Read full complaint
TL* THE CONTACT OWNS A 2014 CHEVROLET TAHOE. WHILE DRIVING 55 MPH, THE SUN ROOF ABRUPTLY SHATTERED INTO PIECES. THE VEHICLE WAS DRIVEN TO THE CONTACT'S RESIDENCE. THERE WERE NO INJURIES. THE DEALER AND MANUFACTURER WERE NOT CONTACTED. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE VIN WAS UNKNOWN. THE FAILURE MILEAGE WAS 43,000.
CRACKING DASH BOARD. MY CAR WAS BOUGHT BRAND NEW AND MY FIRST CRACK OCCURED AT 2 YEARS OLD TO THE LEFT CORNER OF MY AIRBAG. SECOND CRACK JUST RECENTLY OCCURED NEAR DRIVERS SIDE. CHEVROLET AND MY DEALERSHIP ARE NOT HELPING ME TO REPLACE MY DASH.
DASHBOARD IS CRACKED AND OUT OF WARRANTY. THIS VEHICLE IS ONLY 3 YEARS OLD.
TAKATA RECALL CRACKING DASH BY THE PASSENGER AIR BAG VEHICLE ONLY HAS 39,000 MILES
DASHBOARD CRACKED BY AIR BAG AND NOW CRACKED BY STEERING WHEEL
TL* TAKATA RECALL. THE CONTACT OWNS A 2014 CHEVROLET TAHOE. THE CONTACT RECEIVED NOTIFICATION OF AN INTERIM RECALL NOTICE FROM THE MANUFACTURER CONCERNING THE AIR BAGS IN MID JULY OF 2016. THE MANUFACTURER AND DEALER (COVERT BUICK GMC 11750 RESEARCH BLVD, AUSTIN, TX 78759 (512) 583-3411) INDICATED THAT FURTHER TESTING WAS BEING …
Read full complaint
TL* TAKATA RECALL. THE CONTACT OWNS A 2014 CHEVROLET TAHOE. THE CONTACT RECEIVED NOTIFICATION OF AN INTERIM RECALL NOTICE FROM THE MANUFACTURER CONCERNING THE AIR BAGS IN MID JULY OF 2016. THE MANUFACTURER AND DEALER (COVERT BUICK GMC 11750 RESEARCH BLVD, AUSTIN, TX 78759 (512) 583-3411) INDICATED THAT FURTHER TESTING WAS BEING DONE FOR MONTHS BY GM AND THEY HAD NOT YET PROVIDED A REMEDY AND PARTS TO SERVICE THE AIR BAG ISSUE. THE MANUFACTURER WAS CONTACTED AGAIN TO DETERMINE WHEN THE VEHICLE WOULD RECEIVE THE RECALL REPAIR PARTS. THE CONTACT WAS NOT EXPERIENCING A FAILURE.
SEVERAL LARGE CRACKS APPEARING IN THE DASHBOARD ABOVE THE STEERING WHEEL AND ALONG THE SPEAKERS IN THE DASHBOARD.
ON MULTIPLE OCCASIONS WHEN ACCELERATING, HIGHWAY AND SUBDIVISION STREETS, THE VEHICLES TRAILER BRAKE WOULD ENGAGE AND THE CAR WOULD BECOME UNSAFE TO CONTINUE DRIVING. THE VEHICLE'S RADIO WOULD ALSO RANDOMLY RESTART, THE INSTRUMENT PANEL WOULD FLICKER ON AND OFF AND THE POWER DOOR LOCKS WOULD CYCLE UP AND DOWN CONTINUOUSLY. THE…
Read full complaint
ON MULTIPLE OCCASIONS WHEN ACCELERATING, HIGHWAY AND SUBDIVISION STREETS, THE VEHICLES TRAILER BRAKE WOULD ENGAGE AND THE CAR WOULD BECOME UNSAFE TO CONTINUE DRIVING. THE VEHICLE'S RADIO WOULD ALSO RANDOMLY RESTART, THE INSTRUMENT PANEL WOULD FLICKER ON AND OFF AND THE POWER DOOR LOCKS WOULD CYCLE UP AND DOWN CONTINUOUSLY. THE ONLY WANT TO RESET THE VEHICLE WAS TO TURN IT OFF FOR A LITTLE BIT AND THEN BACK ON AND THE PROBLEM WOULD GO AWAY FOR A LITTLE WHILE. THERE ARE MULTIPLE ACCOUNTS ONLINE OF OTHER CHEVY VEHICLES HAVING VERY SIMILAR ISSUES, ALL WHICH SEEM TO BE RELATED TO THE NEGATIVE BATTERY CABLE NOT PROPERLY HANDLING THE LOAD AND NEEDING TO BE REPLACED.
DRIVING DOWN THE ROAD, MY DASHBOARD CRACKED ON THE CORNER OF THE PASSENGER SIDE AIR BAG. THE DASHBOARD WAS NOT STRUCK IN ANYWAY OR THE CAR DID NOT HIT A BUMP. I'M AFRAID OF THE CRACK BEING THERE BECAUSE IT IS SO CLOSE TO THE AIRBAG HOUSING.
Official recalls
321V054000 · Air Bags:frontal:passenger Side:inflator Module
Feb 5, 2021
General Motors, LLC (GM) is recalling certain 2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of AL, CA, FL, GA, HI, LA, MS, SC, TX, PR, AS, GU, the MP, and VI or "Zone A." Additionally GM is recalling certain 2011-2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, Yukon XL and 2011-2013 Cadillac Escalade EXT, Chevrolet Avalanche, Silverado 1500, and GMC Sierra 1500 vehicles originally sold, or ever registered, in the states of AZ, AR, DE, DC, IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV or "Zone B." Additionally, GM is recalling certain 2010-2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, and Yukon XL and 2010-2013 Cadillac Escalade EXT, Chevrolet Avalanche, Silverado 1500, and GMC Sierra 1500 vehicles originally sold, or ever registered, in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY or "Zone C." These vehicles are equipped with non-desiccated passenger frontal inflators containing phase-stabilized ammonium nitrate (PSAN) propellant. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 25, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed to 40 VIN owners on May 11, 2021. A second owner notification letter was mailed to all other owners on January 24, 2022. Owners may contact Chevrolet customer service at 1-800-222-1020; Cadillac customer service at 1-800-458-8006; and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328800.
14V614000 · Electrical System
Oct 1, 2014
General Motors LLC (GM) is recalling certain model year 2013-2014 Cadillac CTS, Escalade, Escalade ESV, Chevrolet Suburban, Tahoe, GMC Yukon, and Yukon XL, and 2014 Buick Enclave, Chevrolet Express, Impala, Silverado HD, Traverse, GMC Acadia, Savana, and Sierra HD vehicles. In the affected vehicles, the chassis electronic module may be internally contaminated, resulting in an electrical short.
Consequence & remedy
Consequence: If the module experiences an electrical short, the vehicle could stall, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will replace the chassis electronic module, free of charge. The recall began on December 26, 2014. Owners may contact GM customer service at 1-800-521-7300 (Buick), 1-800-458-006 (Cadillac), 1-800-222-1020 (Chevrolet), and 1-800-462-8782 (GMC). GMs number for this recall is 14515.
13V342000 · Service Brakes, Hydraulic
Aug 6, 2013
General Motors is recalling certain model year 2014 Chevrolet Suburban vehicles manufactured July 9, 2013, through July 22, 2013; and 2014 Chevrolet Tahoe vehicles manufactured July 16, 2013, through July 23, 2013; and model year 2014 GMC Yukon vehicles manufactured July 13, 2013, through July 18, 2013; and model year 2014 GMC Yukon XL vehicles manufactured on July 22, 2013. The rear brake caliper bolts may not be fully tightened. Thus, these vehicles fail to conform to the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 135, "Light Vehicle Brake Systems."
Consequence & remedy
Consequence: Loose caliper bolts may cause reduced braking performance and result in lengthened stopping distances, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will inspect the bolts on both rear brake caliper brackets. Any bolts found loose will be replaced and tightened. This service will be performed, at no charge. Owners may contact Chevrolet at 1-800-222-1020 and GMC at 1-800-462-8782. GM's recall number is 13247.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.