NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
314 reportsMileage unknown · Jul 25, 2016
Air Bags
TL* TAKATA RECALL. THE CONTACT OWNS A 2010 CHEVROLET TAHOE. THE CONTACT STATED THAT THE DASHBOARD EXHIBITED A CRACK NEAR THE FRONT PASSENGER'S SIDE AIR BAG HOUSING. THE VIN WAS INCLUDED IN NHTSA CAMPAIGN NUMBER: 16V381000 (AIR BAGS) HOWEVER, THE PART NEEDED TO PERFORM THE REPAIR WAS UNAVAILABLE. THE CONTACT STATED THAT THE MANUF…
Read full complaint
TL* TAKATA RECALL. THE CONTACT OWNS A 2010 CHEVROLET TAHOE. THE CONTACT STATED THAT THE DASHBOARD EXHIBITED A CRACK NEAR THE FRONT PASSENGER'S SIDE AIR BAG HOUSING. THE VIN WAS INCLUDED IN NHTSA CAMPAIGN NUMBER: 16V381000 (AIR BAGS) HOWEVER, THE PART NEEDED TO PERFORM THE REPAIR WAS UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE DEALER DECLINED A LOANER VEHICLE. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. THE VIN TOOL CONFIRMS PARTS NOT AVAILABLE.
NHTSA ODI #10888144
104,000 miles · Jul 24, 2016
Unknown Or Other
2010 TAHOE LT - GARAGE KEPT SINCE BOUGHT IN 2011 - DASH HAS CRACKED AT THE TOP LEFT OF THE PASSENGER SIDE AIR BAG. THIS POSES A SIGNIFICANT RISK IF THE PASSENGER SIDE AIRBAG WERE TO DEPLOY. LOOKING FOR SOLUTIONS TO GET THIS FIXED. VEHICLE WAS PARKED IN THE GARAGE AND WAS FINE, THE NEXT MORNING THE DASH WAS CRACKED.
NHTSA ODI #10888064
80,000 miles · Jul 22, 2016
Unknown Or Other
CRACKED DASHBOARD NEAR THE PASSENGER AIR BAG AND ABOVE THE SPEEDOMETER
NHTSA ODI #10887839
53,000 miles · Jul 22, 2016
Structure
THE DASH BOARD CRACKED AFTER BEU6NG PARKED OUTSIDE FOR NO MORE THAN 4 HOURS.
NHTSA ODI #10887653
25,780 miles · Jul 21, 2016
Unknown Or Other
CHEVROLET TAHOE 2010 25780 MILES ON VEHICLE.OWNED SINCE NEW. CRACKING DASHBOARD. DASH CRACKED AT CORNER OF PASSENGER AIRBAG AND ABOVE INSTRUMENT PANEL. PLASTIC AT CRACKS IS SHAPE AND A SAFETY HAZARD. IF AIR DEPLOYS, UNSURE IF REMAINDER OF DASH WITH COME APART EXPOSING OCCUPANTS TO FLYING OR IMPACTING SHARP SHARDS OF PLASTIC.
NHTSA ODI #10886300
Mileage unknown · Jul 14, 2016
Unknown Or Other
THE DASH BOARD HAS CRACKED SEVERELY ON MY 2010 CHEVY TAHOE. I PURCHASED THE VEHICLE IN 2011 WITH NO CRACKS. TWO YEARS LATER THE CRACKING BEGAN.
NHTSA ODI #10884803
50,000 miles · Jul 7, 2016
Structure
GARAGE KEPT TAHOE HAS CRACKED DASHBOARD ABOVE INSTRUMENT PANEL AND PASSENGER SIDE AIRBAG. IF CAR WAS IN AN ACCIDENT, SHARDS OF SHARP PLASTIC COULD INJURE PASSENGERS. THIS IS A COMMON ISSUE IN GM VEHICLES. GM SHOULD HAVE A RECALL TO REPLACE THE DASHBOARD.
NHTSA ODI #10883473
50,000 miles · Jul 1, 2016
Structure
THE DASHBOARD OF MY 2010 TAHOE CRACKED AROUND 55K MILES IN 2015 WHILE DRIVING. IT SEEMS LIKE THIS DEFECT IS DUE TO THE AMOUNT OF VIBRATION/USAGE OF VEHICLE, SINCE MOST NOTICE DAMAGE AFTER 50K MILES REGARDLESS OF HOW LONG THEY'VE OWNED IT OR ITS EXPOSURE TO THE SUN.
NHTSA ODI #10882195
72,000 miles · Jun 26, 2016
Unknown Or Other
I PURCHASED BRAND NEW CHEVROLET TAHOE IN 2010, THE VEHICLE HAS LESS THAN 75,000 MILES AND HAS DEVELOPED A CRACK IN THE DASHBOARD. THIS VEHICLE HAS BEEN TAKEN CARE OF SINCE PURCHASE, SO VERY UPSET THAT THE DASHBOARD HAS CRACKED. IT STARTED CRACKING A YEAR AFTER HAVING WARRANTY WORK DONE ( DASH HAD TO BE REMOVED TO REPLACE ONSTAR …
Read full complaint
I PURCHASED BRAND NEW CHEVROLET TAHOE IN 2010, THE VEHICLE HAS LESS THAN 75,000 MILES AND HAS DEVELOPED A CRACK IN THE DASHBOARD. THIS VEHICLE HAS BEEN TAKEN CARE OF SINCE PURCHASE, SO VERY UPSET THAT THE DASHBOARD HAS CRACKED. IT STARTED CRACKING A YEAR AFTER HAVING WARRANTY WORK DONE ( DASH HAD TO BE REMOVED TO REPLACE ONSTAR SYSTEM).
NHTSA ODI #10876671
85,000 miles · Jun 16, 2016
Unknown Or Other
TAKATA RECALL, THE DASHBOARD IS CRACKING AND SHATTERING INTO SMALL PIECES AND WHEN YOU USE THE DEFROST THE LITTLE PIECES OF DEBRIS START FLYING EVERYWHERE INCLUDING THE DRIVERS FACE. AND IT'S VERY ANNOYING AND DISTRACTING. THANKS FOR ANY HELP.
NHTSA ODI #10874727
Official recalls
3Feb 5, 2021
General Motors, LLC (GM) is recalling certain 2007-2011 Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado 1500, Suburban, Tahoe, GMC Sierra 1500, Yukon, Yukon XL, and 2009-2011 Chevrolet Silverado 2500, Silverado 3500, GMC Sierra 2500 and Sierra 3500 vehicles originally sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, GM is recalling certain 2007-2008 Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado 1500, Suburban, Tahoe, GMC Sierra 1500, Yukon, Yukon XL vehicles originally sold, or ever registered, in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." These vehicles are equipped with non-desiccated passenger frontal inflators containing phase-stabilized ammonium nitrate (PSAN) propellant. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 22, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed on March 1, 2021. Owners may contact Chevrolet customer service at 1-800-222-1020; Cadillac customer service at 1-800-458-8006; and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328760.
Feb 5, 2021
General Motors, LLC (GM) is recalling certain 2013 Cadillac Escalade, Escalade ESV, and Escalade EXT, Chevrolet Avalanche, Silverado 1500, Silverado 2500/3500, Suburban, Tahoe, GMC Sierra 1500, Sierra 2500/3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, GM is recalling certain 2010 Cadillac Escalade, Escalade ESV, and Escalade EXT, Chevrolet Avalanche, Silverado 1500, Silverado 2500/3500, Suburban, Tahoe, GMC Sierra 1500, Sierra 2500/3500, Yukon, and Yukon XL vehicles originally sold, or ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Additionally, GM is recalling certain 2009 Cadillac Escalade, Escalade ESV, and Escalade EXT, Chevrolet Avalanche, Silverado 1500, Silverado 2500/3500, Suburban, Tahoe, GMC Sierra 1500, Sierra 2500/3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C."
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 24, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed on May 11, 2021. Owners may contact Cadillac customer service at 1-800-458-8006; Chevrolet customer service at 1-800-222-1020; and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328790.
Feb 5, 2021
General Motors, LLC (GM) is recalling certain 2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of AL, CA, FL, GA, HI, LA, MS, SC, TX, PR, AS, GU, the MP, and VI or "Zone A." Additionally GM is recalling certain 2011-2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, Yukon XL and 2011-2013 Cadillac Escalade EXT, Chevrolet Avalanche, Silverado 1500, and GMC Sierra 1500 vehicles originally sold, or ever registered, in the states of AZ, AR, DE, DC, IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV or "Zone B." Additionally, GM is recalling certain 2010-2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, and Yukon XL and 2010-2013 Cadillac Escalade EXT, Chevrolet Avalanche, Silverado 1500, and GMC Sierra 1500 vehicles originally sold, or ever registered, in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY or "Zone C." These vehicles are equipped with non-desiccated passenger frontal inflators containing phase-stabilized ammonium nitrate (PSAN) propellant. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 25, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed to 40 VIN owners on May 11, 2021. A second owner notification letter was mailed to all other owners on January 24, 2022. Owners may contact Chevrolet customer service at 1-800-222-1020; Cadillac customer service at 1-800-458-8006; and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328800.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
DP15004 · Rollover Side Curtain Air Bags
Opened Jun 11, 2015 · Closed Mar 7, 2017
Status: closed (inferred from source dates) · Air Bags; Air Bags:side/window; Air Bags:side/window:curtain
In June 2015, the Office of Defects Investigation (ODI) opened this Defect Petition in response to a petition (see ODI 10568388) requesting a defect investigation of several alleged defects that can cause occupant ejections during rollover crashes in certain General Motors vehicles.The petition focused on a 2011 Texas crash involving a model year 2010 Chevrolet Tahoe, which allegedly resulted in multiple occupants to be ejected.One of the ejected occupants was fatally injured.In assessing the petitioner's request, ODI reviewed information from the petitioner, technical information related to rollover side curtain air bags from General Motors (note: ODI did not request GM's field incident data), NHTSA's prior testing and evaluation work related to FMVSS No. 226 Ejection Mitigation, and potentially relevant reports in the NHTSA complaint and crash databases.Based on the information available at the present time, NHTSA does not believe that a safety-related defect currently exists in the design of the rollover side curtain air bags in the model year 2010 Chevrolet Tahoe and other similarly designed Tahoe and Yukon vehicles.Therefore, the petition is denied.However, the agency will take further action if warranted by changing future circumstances.The official petition denial, as published in the Federal Register, is available in the document file for this petition.
Additional source detail variants (3)
Air Bags
In June 2015, the Office of Defects Investigation (ODI) opened this Defect Petition in response to a petition (see ODI 10568388) requesting a defect investigation of several alleged defects that can cause occupant ejections during rollover crashes in certain General Motors vehicles.The petition focused on a 2011 Texas crash involving a model year 2010 Chevrolet Tahoe, which allegedly resulted in multiple occupants to be ejected.One of the ejected occupants was fatally injured.In assessing the petitioner's request, ODI reviewed information from the petitioner, technical information related to rollover side curtain air bags from General Motors (note: ODI did not request GM's field incident data), NHTSA's prior testing and evaluation work related to FMVSS No. 226 Ejection Mitigation, and potentially relevant reports in the NHTSA complaint and crash databases.Based on the information available at the present time, NHTSA does not believe that a safety-related defect currently exists in the design of the rollover side curtain air bags in the model year 2010 Chevrolet Tahoe and other similarly designed Tahoe and Yukon vehicles.Therefore, the petition is denied.However, the agency will take further action if warranted by changing future circumstances.The official petition denial, as published in the Federal Register, is available in the document file for this petition.
Air Bags:side/window:curtain
In June 2015, the Office of Defects Investigation (ODI) opened this Defect Petition in response to a petition (see ODI 10568388) requesting a defect investigation of several alleged defects that can cause occupant ejections during rollover crashes in certain General Motors vehicles.The petition focused on a 2011 Texas crash involving a model year 2010 Chevrolet Tahoe, which allegedly resulted in multiple occupants to be ejected.One of the ejected occupants was fatally injured.In assessing the petitioner's request, ODI reviewed information from the petitioner, technical information related to rollover side curtain air bags from General Motors (note: ODI did not request GM's field incident data), NHTSA's prior testing and evaluation work related to FMVSS No. 226 Ejection Mitigation, and potentially relevant reports in the NHTSA complaint and crash databases.Based on the information available at the present time, NHTSA does not believe that a safety-related defect currently exists in the design of the rollover side curtain air bags in the model year 2010 Chevrolet Tahoe and other similarly designed Tahoe and Yukon vehicles.Therefore, the petition is denied.However, the agency will take further action if warranted by changing future circumstances.The official petition denial, as published in the Federal Register, is available in the document file for this petition.
Air Bags:side/window
In June 2015, the Office of Defects Investigation (ODI) opened this Defect Petition in response to a petition (see ODI 10568388) requesting a defect investigation of several alleged defects that can cause occupant ejections during rollover crashes in certain General Motors vehicles.The petition focused on a 2011 Texas crash involving a model year 2010 Chevrolet Tahoe, which allegedly resulted in multiple occupants to be ejected.One of the ejected occupants was fatally injured.In assessing the petitioner's request, ODI reviewed information from the petitioner, technical information related to rollover side curtain air bags from General Motors (note: ODI did not request GM's field incident data), NHTSA's prior testing and evaluation work related to FMVSS No. 226 Ejection Mitigation, and potentially relevant reports in the NHTSA complaint and crash databases.Based on the information available at the present time, NHTSA does not believe that a safety-related defect currently exists in the design of the rollover side curtain air bags in the model year 2010 Chevrolet Tahoe and other similarly designed Tahoe and Yukon vehicles.Therefore, the petition is denied.However, the agency will take further action if warranted by changing future circumstances.The official petition denial, as published in the Federal Register, is available in the document file for this petition.
Illustration