NHTSA owner reports · September 18, 2026 snapshot.
Structure complaints
279 reportsClear category filter113,010 miles · Nov 29, 2010
Latches/locks/linkagesStructure
I HAVE A 2007 CHEVY TAHOE AND AM EXPERIENCING THE INTERIOR DOOR HANDLE PROBLEM THAT SO MANY OTHERS HAVE. THE CHROME-LIKE PLATING IS PEELING AND IS RAZOR SHARP. THE PASSENGER SIDE CUT MY HUSBAND'S FINGER. HE SAID IT WAS VERY PAINFUL AND IT BLED FOR A WHILE - EVEN STARTED AGAIN A DAY LATER. THE DRIVER'S SIDE IS DOING THE SAME …
Read full complaint
I HAVE A 2007 CHEVY TAHOE AND AM EXPERIENCING THE INTERIOR DOOR HANDLE PROBLEM THAT SO MANY OTHERS HAVE. THE CHROME-LIKE PLATING IS PEELING AND IS RAZOR SHARP. THE PASSENGER SIDE CUT MY HUSBAND'S FINGER. HE SAID IT WAS VERY PAINFUL AND IT BLED FOR A WHILE - EVEN STARTED AGAIN A DAY LATER. THE DRIVER'S SIDE IS DOING THE SAME THING, BUT I HAVE NOT CUT MYSELF - YET. *TR
NHTSA ODI #10368167
51,300 miles · Oct 29, 2010
Latches/locks/linkagesStructure
PEELING METAL PLATING ON THE DRIVER'S DOOR HANDLE IS CUTTING MY HAND WHEN I OPEN THE DOOR; I HAVE TAKEN THE VEHICLE TO THE CHEVROLET DEALERSHIP, BUT THEY SAY THAT THE VIN NUMBER OF MY TAHOE IS NOT COVERED BY THE PREVIOUS RECALL. *TR
NHTSA ODI #10362935
56,000 miles · Oct 23, 2010
Latches/locks/linkagesStructureInjury
I HAVE A 2007 CHEVY TAHOE AND BOTH THE DRIVER AND PASSENGER INTERIOR DOOR HANDLES HAVE BEGAN TO PEEL AND ARE VERY SHARP. MY WIFE AND MYSELF ARE VERY CAREFUL WHEN WE OPEN OR CLOSE THE DOORS SO AS TO NOT CUT OURSELVES, BUT MY 2 YEAR OLD SON WAS IN THE FRONT SEAT WHILE I WAS CLEANING THE INSIDE OF THE CAR AND CUT HIS HAND ON THE D…
Read full complaint
I HAVE A 2007 CHEVY TAHOE AND BOTH THE DRIVER AND PASSENGER INTERIOR DOOR HANDLES HAVE BEGAN TO PEEL AND ARE VERY SHARP. MY WIFE AND MYSELF ARE VERY CAREFUL WHEN WE OPEN OR CLOSE THE DOORS SO AS TO NOT CUT OURSELVES, BUT MY 2 YEAR OLD SON WAS IN THE FRONT SEAT WHILE I WAS CLEANING THE INSIDE OF THE CAR AND CUT HIS HAND ON THE DOOR HANDLES. IT WASN'T BAD ENOUGH TO NEED STITCHES BUT BELIEVE THIS IS A DEFECT THAT GM SHOULD REPLACE FOR FREE, TO PREVENT WORSE CUTS FROM HAPPENING. *TR
NHTSA ODI #10362082
58,000 miles · Oct 23, 2010
Latches/locks/linkagesStructure
CHROME IS SEPARATING FROM THE LEFT FRONT INSIDE DOOR HANDLE. AS A RESULT, THE CHROME IS JAGGED AND I HAVE CUT MY HAND NUMEROUS TIME. I HEARD THAT THIS WAS A COMMON PROBLEM WITH THIS MODEL. 2007 CHEVROLET TAHOE LT. *TR
NHTSA ODI #10361906
42,000 miles · Oct 15, 2010
StructureCrash
THERE IS A 10INCH CRACK IN THE HUMP OF THE DASH ABOVE MY ODOMETER. I HAVE AN 07 CHEVY TAHOE WITH ABOUT 40K. I CONTACTED A CHEVY DEALER AND THEY SAID IT WAS NOT A CHEVY PROBLEM. *TR
NHTSA ODI #10360631
95,000 miles · Sep 23, 2010
Structure
I OWE A 2007 CHEVROLET TAHOE. I NOTICED IN JULY OF THIS YEAR THAT THERE IS A 2-3 INCH CRACK ON THE TOP LEFT CORNER OF THE DASH ON THE PASSENGER'S SIDE--RIGHT ON TOP OF WHERE THE AIR BAG IS! I TOOK THE VEHICLE TO THE DEALER AND THEY SAID "SINCE IT'S NOT A SAFETY ISSUE" GENERAL MOTORS SAID THEY WILL NOT REPLACE THE DASH! HOW DO…
Read full complaint
I OWE A 2007 CHEVROLET TAHOE. I NOTICED IN JULY OF THIS YEAR THAT THERE IS A 2-3 INCH CRACK ON THE TOP LEFT CORNER OF THE DASH ON THE PASSENGER'S SIDE--RIGHT ON TOP OF WHERE THE AIR BAG IS! I TOOK THE VEHICLE TO THE DEALER AND THEY SAID "SINCE IT'S NOT A SAFETY ISSUE" GENERAL MOTORS SAID THEY WILL NOT REPLACE THE DASH! HOW DO THEY FREAKING KNOW IT'S NOT A SAFETY ISSUE WHEN IT'S ON TOP OF THE AIR BAG??? AND NOW THERE'S ANOTHER CRACK! THIS ONE IS JUST TO THE LEFT OF THE DRIVER'S SIDE INSTRUMENT PANEL ON TOP OF THE DASH! THIS CRACK IS 6-7 INCHES LONG. I TAKE SUPER GOOD CARE OF MY VEHICLES, SUN SHADES, REGULAR CONDITIONING, ETC. AND SINCE THE VEHICLE IS 4 YEARS OLD, THERE IS NO REASON (OTHER THAN CRAPPY WORKMANSHIP AND CRAPPY MATERIALS AND CRAPPY ENGINEERING) TO HAVE NOT ONE BUT TWO CRACKS ON A $50,000 VEHICLE! SO I'M GUESSING WHEN MY AIR BAG FAILS ON MY PASSENGER SIDE AND WHEN MY DAUGHTER GETS HURT IN A WRECK BECAUSE THE AIRBAG DOESN'T PROPERLY DEPLOY, THEN IT WILL BE A SAFETY ISSUE BECAUSE I WILL BE ALL OVER GENERAL MOTORS. THIS IS NOT AN ISOLATED INCIDENT. CHECK THE INTERNET. HUNDREDS OF COMPLAINTS OF THE SAME CRACKS HAPPENING. GM IS AWARE OF THE PROBLEM AND IS CHOOSING TO DO NOTHING ABOUT IT. PLEASE LOOK INTO THIS ISSUE AND HELP US GET THIS PROBLEM RESOLVED. *TR
NHTSA ODI #10357264
60,000 miles · Sep 6, 2010
Structure
I HAVE A 2007 CHEVY TAHOE LTZ WITH 60K MILES ON IT NOW. MY GIRLFRIEND NORMALLY RIDES WITH ME AND HAS CUT HER HAND ON SEVERAL OCCASIONS NOW ON MY INTERIOR DOOR HANDLE THAT IS PEELING. IT STARTED WITH THE FRONT PASSENGER SIDE DOOR HANDLE, AND NOW ALL 4 DOOR HANDLES ARE PEELING ON THE CAR AND THE METAL THAT IS STILL ON POSES A SERI…
Read full complaint
I HAVE A 2007 CHEVY TAHOE LTZ WITH 60K MILES ON IT NOW. MY GIRLFRIEND NORMALLY RIDES WITH ME AND HAS CUT HER HAND ON SEVERAL OCCASIONS NOW ON MY INTERIOR DOOR HANDLE THAT IS PEELING. IT STARTED WITH THE FRONT PASSENGER SIDE DOOR HANDLE, AND NOW ALL 4 DOOR HANDLES ARE PEELING ON THE CAR AND THE METAL THAT IS STILL ON POSES A SERIOUS CUT RISK. I WENT TO THE DEALER AND SO FAR THEY TOLD ME THEY CAN REPLACE THE PARTS BUT AT A COST AND LABOR TO ME, NOT COVERING ANY PORTION. AFTER RESEARCHING THIS IT SEEMS TO BE A MAJOR PROBLEM WITH MY TYPE OF CAR MODEL AND I FEEL LIKE GM SHOULD DEAL WITH THIS CRAPPY PART AND REPLACE FOR FREE. *TR
NHTSA ODI #10354027
34,850 miles · Aug 29, 2010
StructureInjury
I HAVE A 2007 CHEVROLET TAHOE LT. RECENTLY THE CHROME PLATING ON THE PASSENGER SIDE DOOR HANDLE JUST STARTED PEELING FOR NO REASON. IT IS SHARP AS A RAZOR BLADE AND EXTREMELY DANGEROUS. MY WIFE ALREADY CUT HER FINGER VERY BADLY. THIS IS DEFINITELY A MANUFACTURING ISSUE AND AN EXTREME HAZARD. *TR
NHTSA ODI #10352589
Mileage unknown · Aug 2, 2010
Structure
I JUST PURCHASED A USED 2007 CHEVY TAHOE AND I HAVE CUT MY FINGERS ON BOTH DOOR HANDLES. IT SEEMS THAT THEY USED CHEAP CHROME PLATED HANDLES AND IT IS PEALING. IT IS RAZOR SHARP. I AM JUST GLAD NEITHER MY WIFE OR KIDS GOT CUT. PLEASE RESEARCH THIS AND SEE IF THERE ARE OTHERS. DEALER WILL NOT REPLACE BECAUSE THE VEHICLE HAS …
Read full complaint
I JUST PURCHASED A USED 2007 CHEVY TAHOE AND I HAVE CUT MY FINGERS ON BOTH DOOR HANDLES. IT SEEMS THAT THEY USED CHEAP CHROME PLATED HANDLES AND IT IS PEALING. IT IS RAZOR SHARP. I AM JUST GLAD NEITHER MY WIFE OR KIDS GOT CUT. PLEASE RESEARCH THIS AND SEE IF THERE ARE OTHERS. DEALER WILL NOT REPLACE BECAUSE THE VEHICLE HAS OVER 36,000 MILES. THIS SHOULD BE FIXED! THANKS *TR
NHTSA ODI #10346840
65,000 miles · Jul 16, 2010
Structure
I OWN A 2007 TAHOE LT. THE DASH IS CRACK ABOVE THE SPEEDOMETER AND BY THE PASSENGER AIR BAG. MY INTERIOR DOOR LATCHES ARE ALSO PEELING AND ARE SHARP ENOUGH TO SLICE A FINGER. THESE PROBLEMS SEEM TO BE PRETTY COMMON AND SHOULD BE TAKEN CARE OF BY GM. YOU WONDER WHY CUSTOMERS DECIDE TO BUY IMPORTS. CUSTOMER SERVICE IS A BIG PART O…
Read full complaint
I OWN A 2007 TAHOE LT. THE DASH IS CRACK ABOVE THE SPEEDOMETER AND BY THE PASSENGER AIR BAG. MY INTERIOR DOOR LATCHES ARE ALSO PEELING AND ARE SHARP ENOUGH TO SLICE A FINGER. THESE PROBLEMS SEEM TO BE PRETTY COMMON AND SHOULD BE TAKEN CARE OF BY GM. YOU WONDER WHY CUSTOMERS DECIDE TO BUY IMPORTS. CUSTOMER SERVICE IS A BIG PART OF REPEAT BUSINESS. *TR
NHTSA ODI #10343591
Official recalls
4Feb 5, 2021
General Motors, LLC (GM) is recalling certain 2007-2011 Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado 1500, Suburban, Tahoe, GMC Sierra 1500, Yukon, Yukon XL, and 2009-2011 Chevrolet Silverado 2500, Silverado 3500, GMC Sierra 2500 and Sierra 3500 vehicles originally sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, GM is recalling certain 2007-2008 Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado 1500, Suburban, Tahoe, GMC Sierra 1500, Yukon, Yukon XL vehicles originally sold, or ever registered, in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." These vehicles are equipped with non-desiccated passenger frontal inflators containing phase-stabilized ammonium nitrate (PSAN) propellant. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 22, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed on March 1, 2021. Owners may contact Chevrolet customer service at 1-800-222-1020; Cadillac customer service at 1-800-458-8006; and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328760.
Feb 5, 2021
General Motors, LLC (GM) is recalling certain 2009 Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado 1500, Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 1500, Sierra 2500, Sierra 3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Additionally, GM is recalling certain 2007-2008 Cadillac Escalade, Escalade ESV, and Escalade EXT, Chevrolet Avalanche, Silverado 1500, Suburban, Tahoe, GMC Sierra 1500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C." These vehicles are equipped with non-desiccated passenger frontal inflators containing phase-stabilized ammonium nitrate (PSAN) propellant. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 23, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed on September 20, 2021. Owners may contact Chevrolet customer service at 1-800-222-1020, Cadillac customer service at 1-800-458-8006, and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328780.
Jun 4, 2010
GM IS RECALLING CERTAIN MODEL YEAR 2006-2009 BUICK, LUCERNE; CADILLAC DTS; HUMMER H2; MODEL YEAR 2008-2009 BUICK ENCLAVE; CADILLAC CTS; MODEL YEAR 2007-2009 CADILLAC ESCALADE, ESCALADE ESV, ESCALADE EXT; CHEVROLET AVALANCHE, SILVERADO, SUBURBAN, TAHOE; GMC ACADIA, SIERRA, YUKON, YUKON XL; SATURN OUTLOOK; AND MODEL YEAR 2009 CHEVROLET TRAVERSE VEHICLES EQUIPPED WITH A HEATED WASHER FLUID SYSTEM (HWFS). A RECALL WAS IMPLEMENTED IN 2008 TO ADD A FUSE TO THE CONTROL CIRCUIT HARNESS TO ADDRESS THE POTENTIAL CONSEQUENCES OF A PRINTED CIRCUIT BOARD (PCB) ELECTRICAL SHORT. HOWEVER, THERE HAVE BEEN NEW REPORTS OF THERMAL INCIDENTS ON HWFS MODULES AFTER THIS IMPROVEMENT WAS INSTALLED. THESE INCIDENTS RESULTED FROM A NEW FAILURE MODE ATTRIBUTED TO THE DEVICE'S THERMAL PROTECTION FEATURE. THE SIGNIFICANCE VARIES FROM MINOR DISTORTION TO CONSIDERABLE MELTING OF THE PLASTIC AROUND THE HWFS FLUID CHAMBER.
Consequence & remedy
Consequence: IT IS POSSIBLE FOR THE HEATED WASHER MODULE TO IGNITE AND A FIRE MAY OCCUR.
Remedy: DEALERS WILL PERMANENTLY DISABLE AND REMOVE THE HEATED WASHER FLUID MODULE. AN UPDATED PAGE FOR THE OWNER MANUAL WILL BE PROVIDED AND INSERTED IN THE OWNER MANUAL TO DOCUMENT THAT THE FEATURE HAS BEEN PERMANENTLY DISABLED AND REMOVED FROM THE VEHICLE. THE SAFETY RECALL BEGAN ON JUNE 11, 2010. OWNERS MAY CONTACT BUICK AT 1-866-608-8080, CADILLAC AT 1-866-982-2339, CHEVROLET AT 1-800-630-2438, SATURN AT 1-800-972-8876, GMC AT 1-866-996-9463 AND HUMMER AT 1-800-732-5493 OR AT THE OWNER CENTER AT WWW.GMOWNERCENTER.COM.
Aug 28, 2008
GM IS RECALLING 857,735 MY 2006-2008 BUICK LUCERNE; CADILLAC DTS; HUMMER H2; MY 2007-2008 CADILLAC ESCALADE, ESCALADE ESV, ESCALADE EXT; CHEVROLET AVALANCHE, SILVERADO, SUBURBAN, TAHOE; GMC ACADIA, SIERRA, YUKON, YUKON XL, SATURN OUTLOOK; AND MY 2008 BUICK ENCLAVE VEHICLES EQUIPPED WITH A HEATED WIPER WASHER FLUID SYSTEM. A SHORT CIRCUIT ON THE PRINTED CIRCUIT BOARD FOR THE WASHER FLUID HEATER MAY OVERHEAT THE CONTROL-CIRCUIT GROUND WIRE.
Consequence & remedy
Consequence: THIS MAY CAUSE OTHER ELECTRICAL FEATURES TO MALFUNCTION, CREATE AN ODOR, OR CAUSE SMOKE INCREASING THE RISK OF A FIRE.
Remedy: DEALERS WILL INSTALL A WIRE HARNESS WITH AN IN-LINE FUSE FREE OF CHARGE. THE RECALL BEGAN ON SEPTEMBER 12, 2008. OWNERS MAY CONTACT BUICK AT 1-866-608-8080; CADILLAC AT 1-800-982-2339 OR HTTP://WWW.CADILLAC.COM; CHEVROLET AT 1-800-630-2438; SATURN AT 1-800-972-8876 OR HTTP://WWW.SATURN.COM, GMC AT 1-866-996-9436; OR HUMMER AT 1-800-732-5493; OR THROUGH THEIR WEBSITE AT <A HREF=HTTP://WWW.GMOWNERCENTER.COM>HTTP://WWW.GMOWNERCENTER.COM</A> .
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
5EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
EA10004 · Interior Door Handle Laceration Risk
Opened May 23, 2010 · Closed Jul 18, 2011
Status: closed (inferred from source dates) · Latches/locks/linkages; Latches/locks/linkages:doors:latch; Structure; Structure:body; Structure:body:door ; Structure:body:door:hinge And Attachments
The investigated concern involved chrome plating on interior door handles that could peel or separate from the plastic base material.This de-lamination could result in a sharp edge and pose a risk of laceration.In some cases, consumers reported minor hand/skin lacerations.Of these reported injuries, the vast majority of injuries were to adults.Ninety percent of claims associated with interior door handle de-lamination were related to the front doors.In addition to the above Tahoe/Yukon vehicles, other GMT 900 series C/K vehicles (Avalanche, Escalade, Sierra, Silverado, and Suburban) have a trim level that utilizes the chrome plated interior door handles and were included in the analysis.The resultant population group had a total of 746 complaint reports with 309 injury incidents and 43,619 unique VIN regular warranty claims over a combined 451,745 vehicle population.The door handle supplier was changed in September 2006 with new tooling and process in place by October 2006.The base population prior to the September 2006 vendor change accounted for the bulk (or 89%) of all complaints and comparable injury reports and warranty claims.Due to the nature of the failure (thin chrome plating peeling off the door handle), only minor hand/skin laceration injuries similar to a paper cut were recorded.All but a few did not require professional medical treatment such as surgical or liquid sutures (i.e. stitches).Less than 10% of injury reports had specifically involved a 3-10 year old child.This was due to the fact that 90% of the claims were associated with door handles located in the front seating area (where the window glass panels usually have less solar tinting than rear window glass panels) where children are not normally seated. In July 2010, GM issued a Special Coverage Policy (SCP 09239) on the base vehicles to extend the warranty coverage to 10 years/100k miles.Recent data indicate that the base population complaint and injury reporting have subsided since the implementation of the SCP campaign.In June 2011, GM added the remaining interim population (Sep-Oct 2006) to the SCP.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Additional source detail variants (6)
Latches/locks/linkages:doors:latch
The investigated concern involved chrome plating on interior door handles that could peel or separate from the plastic base material.This de-lamination could result in a sharp edge and pose a risk of laceration.In some cases, consumers reported minor hand/skin lacerations.Of these reported injuries, the vast majority of injuries were to adults.Ninety percent of claims associated with interior door handle de-lamination were related to the front doors.In addition to the above Tahoe/Yukon vehicles, other GMT 900 series C/K vehicles (Avalanche, Escalade, Sierra, Silverado, and Suburban) have a trim level that utilizes the chrome plated interior door handles and were included in the analysis.The resultant population group had a total of 746 complaint reports with 309 injury incidents and 43,619 unique VIN regular warranty claims over a combined 451,745 vehicle population.The door handle supplier was changed in September 2006 with new tooling and process in place by October 2006.The base population prior to the September 2006 vendor change accounted for the bulk (or 89%) of all complaints and comparable injury reports and warranty claims.Due to the nature of the failure (thin chrome plating peeling off the door handle), only minor hand/skin laceration injuries similar to a paper cut were recorded.All but a few did not require professional medical treatment such as surgical or liquid sutures (i.e. stitches).Less than 10% of injury reports had specifically involved a 3-10 year old child.This was due to the fact that 90% of the claims were associated with door handles located in the front seating area (where the window glass panels usually have less solar tinting than rear window glass panels) where children are not normally seated. In July 2010, GM issued a Special Coverage Policy (SCP 09239) on the base vehicles to extend the warranty coverage to 10 years/100k miles.Recent data indicate that the base population complaint and injury reporting have subsided since the implementation of the SCP campaign.In June 2011, GM added the remaining interim population (Sep-Oct 2006) to the SCP.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Latches/locks/linkages
The investigated concern involved chrome plating on interior door handles that could peel or separate from the plastic base material.This de-lamination could result in a sharp edge and pose a risk of laceration.In some cases, consumers reported minor hand/skin lacerations.Of these reported injuries, the vast majority of injuries were to adults.Ninety percent of claims associated with interior door handle de-lamination were related to the front doors.In addition to the above Tahoe/Yukon vehicles, other GMT 900 series C/K vehicles (Avalanche, Escalade, Sierra, Silverado, and Suburban) have a trim level that utilizes the chrome plated interior door handles and were included in the analysis.The resultant population group had a total of 746 complaint reports with 309 injury incidents and 43,619 unique VIN regular warranty claims over a combined 451,745 vehicle population.The door handle supplier was changed in September 2006 with new tooling and process in place by October 2006.The base population prior to the September 2006 vendor change accounted for the bulk (or 89%) of all complaints and comparable injury reports and warranty claims.Due to the nature of the failure (thin chrome plating peeling off the door handle), only minor hand/skin laceration injuries similar to a paper cut were recorded.All but a few did not require professional medical treatment such as surgical or liquid sutures (i.e. stitches).Less than 10% of injury reports had specifically involved a 3-10 year old child.This was due to the fact that 90% of the claims were associated with door handles located in the front seating area (where the window glass panels usually have less solar tinting than rear window glass panels) where children are not normally seated. In July 2010, GM issued a Special Coverage Policy (SCP 09239) on the base vehicles to extend the warranty coverage to 10 years/100k miles.Recent data indicate that the base population complaint and injury reporting have subsided since the implementation of the SCP campaign.In June 2011, GM added the remaining interim population (Sep-Oct 2006) to the SCP.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Structure:body:door
The investigated concern involved chrome plating on interior door handles that could peel or separate from the plastic base material.This de-lamination could result in a sharp edge and pose a risk of laceration.In some cases, consumers reported minor hand/skin lacerations.Of these reported injuries, the vast majority of injuries were to adults.Ninety percent of claims associated with interior door handle de-lamination were related to the front doors.In addition to the above Tahoe/Yukon vehicles, other GMT 900 series C/K vehicles (Avalanche, Escalade, Sierra, Silverado, and Suburban) have a trim level that utilizes the chrome plated interior door handles and were included in the analysis.The resultant population group had a total of 746 complaint reports with 309 injury incidents and 43,619 unique VIN regular warranty claims over a combined 451,745 vehicle population.The door handle supplier was changed in September 2006 with new tooling and process in place by October 2006.The base population prior to the September 2006 vendor change accounted for the bulk (or 89%) of all complaints and comparable injury reports and warranty claims.Due to the nature of the failure (thin chrome plating peeling off the door handle), only minor hand/skin laceration injuries similar to a paper cut were recorded.All but a few did not require professional medical treatment such as surgical or liquid sutures (i.e. stitches).Less than 10% of injury reports had specifically involved a 3-10 year old child.This was due to the fact that 90% of the claims were associated with door handles located in the front seating area (where the window glass panels usually have less solar tinting than rear window glass panels) where children are not normally seated. In July 2010, GM issued a Special Coverage Policy (SCP 09239) on the base vehicles to extend the warranty coverage to 10 years/100k miles.Recent data indicate that the base population complaint and injury reporting have subsided since the implementation of the SCP campaign.In June 2011, GM added the remaining interim population (Sep-Oct 2006) to the SCP.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Structure:body:door:hinge And Attachments
The investigated concern involved chrome plating on interior door handles that could peel or separate from the plastic base material.This de-lamination could result in a sharp edge and pose a risk of laceration.In some cases, consumers reported minor hand/skin lacerations.Of these reported injuries, the vast majority of injuries were to adults.Ninety percent of claims associated with interior door handle de-lamination were related to the front doors.In addition to the above Tahoe/Yukon vehicles, other GMT 900 series C/K vehicles (Avalanche, Escalade, Sierra, Silverado, and Suburban) have a trim level that utilizes the chrome plated interior door handles and were included in the analysis.The resultant population group had a total of 746 complaint reports with 309 injury incidents and 43,619 unique VIN regular warranty claims over a combined 451,745 vehicle population.The door handle supplier was changed in September 2006 with new tooling and process in place by October 2006.The base population prior to the September 2006 vendor change accounted for the bulk (or 89%) of all complaints and comparable injury reports and warranty claims.Due to the nature of the failure (thin chrome plating peeling off the door handle), only minor hand/skin laceration injuries similar to a paper cut were recorded.All but a few did not require professional medical treatment such as surgical or liquid sutures (i.e. stitches).Less than 10% of injury reports had specifically involved a 3-10 year old child.This was due to the fact that 90% of the claims were associated with door handles located in the front seating area (where the window glass panels usually have less solar tinting than rear window glass panels) where children are not normally seated. In July 2010, GM issued a Special Coverage Policy (SCP 09239) on the base vehicles to extend the warranty coverage to 10 years/100k miles.Recent data indicate that the base population complaint and injury reporting have subsided since the implementation of the SCP campaign.In June 2011, GM added the remaining interim population (Sep-Oct 2006) to the SCP.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Structure:body
The investigated concern involved chrome plating on interior door handles that could peel or separate from the plastic base material.This de-lamination could result in a sharp edge and pose a risk of laceration.In some cases, consumers reported minor hand/skin lacerations.Of these reported injuries, the vast majority of injuries were to adults.Ninety percent of claims associated with interior door handle de-lamination were related to the front doors.In addition to the above Tahoe/Yukon vehicles, other GMT 900 series C/K vehicles (Avalanche, Escalade, Sierra, Silverado, and Suburban) have a trim level that utilizes the chrome plated interior door handles and were included in the analysis.The resultant population group had a total of 746 complaint reports with 309 injury incidents and 43,619 unique VIN regular warranty claims over a combined 451,745 vehicle population.The door handle supplier was changed in September 2006 with new tooling and process in place by October 2006.The base population prior to the September 2006 vendor change accounted for the bulk (or 89%) of all complaints and comparable injury reports and warranty claims.Due to the nature of the failure (thin chrome plating peeling off the door handle), only minor hand/skin laceration injuries similar to a paper cut were recorded.All but a few did not require professional medical treatment such as surgical or liquid sutures (i.e. stitches).Less than 10% of injury reports had specifically involved a 3-10 year old child.This was due to the fact that 90% of the claims were associated with door handles located in the front seating area (where the window glass panels usually have less solar tinting than rear window glass panels) where children are not normally seated. In July 2010, GM issued a Special Coverage Policy (SCP 09239) on the base vehicles to extend the warranty coverage to 10 years/100k miles.Recent data indicate that the base population complaint and injury reporting have subsided since the implementation of the SCP campaign.In June 2011, GM added the remaining interim population (Sep-Oct 2006) to the SCP.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Structure
The investigated concern involved chrome plating on interior door handles that could peel or separate from the plastic base material.This de-lamination could result in a sharp edge and pose a risk of laceration.In some cases, consumers reported minor hand/skin lacerations.Of these reported injuries, the vast majority of injuries were to adults.Ninety percent of claims associated with interior door handle de-lamination were related to the front doors.In addition to the above Tahoe/Yukon vehicles, other GMT 900 series C/K vehicles (Avalanche, Escalade, Sierra, Silverado, and Suburban) have a trim level that utilizes the chrome plated interior door handles and were included in the analysis.The resultant population group had a total of 746 complaint reports with 309 injury incidents and 43,619 unique VIN regular warranty claims over a combined 451,745 vehicle population.The door handle supplier was changed in September 2006 with new tooling and process in place by October 2006.The base population prior to the September 2006 vendor change accounted for the bulk (or 89%) of all complaints and comparable injury reports and warranty claims.Due to the nature of the failure (thin chrome plating peeling off the door handle), only minor hand/skin laceration injuries similar to a paper cut were recorded.All but a few did not require professional medical treatment such as surgical or liquid sutures (i.e. stitches).Less than 10% of injury reports had specifically involved a 3-10 year old child.This was due to the fact that 90% of the claims were associated with door handles located in the front seating area (where the window glass panels usually have less solar tinting than rear window glass panels) where children are not normally seated. In July 2010, GM issued a Special Coverage Policy (SCP 09239) on the base vehicles to extend the warranty coverage to 10 years/100k miles.Recent data indicate that the base population complaint and injury reporting have subsided since the implementation of the SCP campaign.In June 2011, GM added the remaining interim population (Sep-Oct 2006) to the SCP.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
PE09044 · Interior Door Handle Laceration Risk
Opened Sep 14, 2009 · Closed May 23, 2010
Status: closed (inferred from source dates) · Latches/locks/linkages:doors:latch; Structure:body:door
The statistical data regarding problem experience in the table above are net counts for unique vehicles.Review of information in this PE discloses that while accounting for approximately two-thirds of the total population, MY 2007 subject vehicles are cited in more than 90 percent of the consumer complaints, injury reports, and warranty claims, respectively.In addition, improvements in the door handle manufacturing process during the MY 2007 production resulted in a decline in the occurrence of peeling/flaking of the thin chrome plating.Other environmental factors were also identified that may have influenced the occurrence of the condition which poses the alleged safety risk.Additional analysis is required to identify the specific vehicles most susceptible to peeling or separation of the chrome plating from the handle, and to assess the significance of its occurrence.This PE has been upgraded to an Engineering Analysis to facilitate further study.
Additional source detail variants (2)
Latches/locks/linkages:doors:latch
The statistical data regarding problem experience in the table above are net counts for unique vehicles.Review of information in this PE discloses that while accounting for approximately two-thirds of the total population, MY 2007 subject vehicles are cited in more than 90 percent of the consumer complaints, injury reports, and warranty claims, respectively.In addition, improvements in the door handle manufacturing process during the MY 2007 production resulted in a decline in the occurrence of peeling/flaking of the thin chrome plating.Other environmental factors were also identified that may have influenced the occurrence of the condition which poses the alleged safety risk.Additional analysis is required to identify the specific vehicles most susceptible to peeling or separation of the chrome plating from the handle, and to assess the significance of its occurrence.This PE has been upgraded to an Engineering Analysis to facilitate further study.
Structure:body:door
The statistical data regarding problem experience in the table above are net counts for unique vehicles.Review of information in this PE discloses that while accounting for approximately two-thirds of the total population, MY 2007 subject vehicles are cited in more than 90 percent of the consumer complaints, injury reports, and warranty claims, respectively.In addition, improvements in the door handle manufacturing process during the MY 2007 production resulted in a decline in the occurrence of peeling/flaking of the thin chrome plating.Other environmental factors were also identified that may have influenced the occurrence of the condition which poses the alleged safety risk.Additional analysis is required to identify the specific vehicles most susceptible to peeling or separation of the chrome plating from the handle, and to assess the significance of its occurrence.This PE has been upgraded to an Engineering Analysis to facilitate further study.
EA08010 · NON-CRASH Engine Compartment Fires
Opened Jun 12, 2008 · Closed Sep 8, 2008
Status: closed (inferred from source dates) · Electrical System; Electrical SYSTEM:12V/24V/48V Battery; Electrical System:wiring; Electrical System:wiring:front Underhood; Electrical System:wiring:fuses And Circuit Breakers; Engine And Engine Cooling; Engine And Engine Cooling:engine; Visibility:windshield Wiper/washer; Visibility:windshield Wiper/washer:switch/wiring
IN A LETTER DATED AUGUST 27, 2008, GENERAL MOTORS CORP. (GM) NOTIFIED NHTSA THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-441) TO ADDRESS A SAFETY RELATEDDEFECT THAT CAN RESULT IN ENGINE COMPARTMENT FIRE IN APPROXIMATELY 850,000 VEHICLES EQUIPPED WITH A HEATED WINDSHIELD WASHER FLUID OPTION.THE SUBJECT VEHICLES OF THIS INVESTIGATION COMPRISE OVER THREE-QUARTERS OF THE RECALL POPULATION. ACCORDING TO GM, A SHORT CIRCUIT ON THE PRINTED CIRCUIT BOARD FOR THE WINDSHIELD WASHER FLUID HEATER MODULE MAY OVERHEAT THE CONTROL-CIRCUIT GROUND WIRE. THIS MAY CAUSE OTHER ELECTRICAL FEATURES TO MALFUNCTION, CREATE AN ODOR OR CAUSE SMOKE AND IN RARE CASES IT MAY CAUSE A FIRE.AS A REMEDY, GM DEALERS WILL INSTALL A WIRE HARNESS WITH AN IN-LINE FUSE. IN ADDITION TO THE SUBJECT VEHICLES, SEVERAL OTHER GM MODELS WITH THE HEATED WINDSHIELD WASHER FLUID OPTION ARE INCLUDED IN RECALL 08V-441: MY 2006-2008 BUICK LUCERNE (MANUFACTURED AUGUST 2005 THROUGH NOVEMBER 2007); MY 2008 BUICK ENCLAVE (MANUFACTURED FEBRUARY 2007 THROUGH APRIL 2007); MY 2006-2008 CADILLAC DTS (MANUFACTURED MAY 2007 THROUGH NOVEMBER 2007); MY 2007-2008 SATURN OUTLOOK (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007); AND MY 2007-2008 GMC ACADIA (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007) VEHICLES.GM IS INSTRUCTING OWNERS TO TAKE THEIR VEHICLE TO A DEALER FOR SERVICE IF THEY EXPERIENCE SYMPTOMS OF WINDSHIELD WASHER HEATER MODULE SHORT CIRCUITS. GM'S RECALL RESOLVES THE SAFETY DEFECT CONCERNS PURSUED BY THIS INVESTIGATION.THIS ENGINEERING ANALYSIS IS CLOSED.
Additional source detail variants (9)
Electrical SYSTEM:12V/24V/48V Battery
IN A LETTER DATED AUGUST 27, 2008, GENERAL MOTORS CORP. (GM) NOTIFIED NHTSA THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-441) TO ADDRESS A SAFETY RELATEDDEFECT THAT CAN RESULT IN ENGINE COMPARTMENT FIRE IN APPROXIMATELY 850,000 VEHICLES EQUIPPED WITH A HEATED WINDSHIELD WASHER FLUID OPTION.THE SUBJECT VEHICLES OF THIS INVESTIGATION COMPRISE OVER THREE-QUARTERS OF THE RECALL POPULATION. ACCORDING TO GM, A SHORT CIRCUIT ON THE PRINTED CIRCUIT BOARD FOR THE WINDSHIELD WASHER FLUID HEATER MODULE MAY OVERHEAT THE CONTROL-CIRCUIT GROUND WIRE. THIS MAY CAUSE OTHER ELECTRICAL FEATURES TO MALFUNCTION, CREATE AN ODOR OR CAUSE SMOKE AND IN RARE CASES IT MAY CAUSE A FIRE.AS A REMEDY, GM DEALERS WILL INSTALL A WIRE HARNESS WITH AN IN-LINE FUSE. IN ADDITION TO THE SUBJECT VEHICLES, SEVERAL OTHER GM MODELS WITH THE HEATED WINDSHIELD WASHER FLUID OPTION ARE INCLUDED IN RECALL 08V-441: MY 2006-2008 BUICK LUCERNE (MANUFACTURED AUGUST 2005 THROUGH NOVEMBER 2007); MY 2008 BUICK ENCLAVE (MANUFACTURED FEBRUARY 2007 THROUGH APRIL 2007); MY 2006-2008 CADILLAC DTS (MANUFACTURED MAY 2007 THROUGH NOVEMBER 2007); MY 2007-2008 SATURN OUTLOOK (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007); AND MY 2007-2008 GMC ACADIA (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007) VEHICLES.GM IS INSTRUCTING OWNERS TO TAKE THEIR VEHICLE TO A DEALER FOR SERVICE IF THEY EXPERIENCE SYMPTOMS OF WINDSHIELD WASHER HEATER MODULE SHORT CIRCUITS. GM'S RECALL RESOLVES THE SAFETY DEFECT CONCERNS PURSUED BY THIS INVESTIGATION.THIS ENGINEERING ANALYSIS IS CLOSED.
Electrical System
IN A LETTER DATED AUGUST 27, 2008, GENERAL MOTORS CORP. (GM) NOTIFIED NHTSA THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-441) TO ADDRESS A SAFETY RELATEDDEFECT THAT CAN RESULT IN ENGINE COMPARTMENT FIRE IN APPROXIMATELY 850,000 VEHICLES EQUIPPED WITH A HEATED WINDSHIELD WASHER FLUID OPTION.THE SUBJECT VEHICLES OF THIS INVESTIGATION COMPRISE OVER THREE-QUARTERS OF THE RECALL POPULATION. ACCORDING TO GM, A SHORT CIRCUIT ON THE PRINTED CIRCUIT BOARD FOR THE WINDSHIELD WASHER FLUID HEATER MODULE MAY OVERHEAT THE CONTROL-CIRCUIT GROUND WIRE. THIS MAY CAUSE OTHER ELECTRICAL FEATURES TO MALFUNCTION, CREATE AN ODOR OR CAUSE SMOKE AND IN RARE CASES IT MAY CAUSE A FIRE.AS A REMEDY, GM DEALERS WILL INSTALL A WIRE HARNESS WITH AN IN-LINE FUSE. IN ADDITION TO THE SUBJECT VEHICLES, SEVERAL OTHER GM MODELS WITH THE HEATED WINDSHIELD WASHER FLUID OPTION ARE INCLUDED IN RECALL 08V-441: MY 2006-2008 BUICK LUCERNE (MANUFACTURED AUGUST 2005 THROUGH NOVEMBER 2007); MY 2008 BUICK ENCLAVE (MANUFACTURED FEBRUARY 2007 THROUGH APRIL 2007); MY 2006-2008 CADILLAC DTS (MANUFACTURED MAY 2007 THROUGH NOVEMBER 2007); MY 2007-2008 SATURN OUTLOOK (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007); AND MY 2007-2008 GMC ACADIA (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007) VEHICLES.GM IS INSTRUCTING OWNERS TO TAKE THEIR VEHICLE TO A DEALER FOR SERVICE IF THEY EXPERIENCE SYMPTOMS OF WINDSHIELD WASHER HEATER MODULE SHORT CIRCUITS. GM'S RECALL RESOLVES THE SAFETY DEFECT CONCERNS PURSUED BY THIS INVESTIGATION.THIS ENGINEERING ANALYSIS IS CLOSED.
Electrical System:wiring:front Underhood
IN A LETTER DATED AUGUST 27, 2008, GENERAL MOTORS CORP. (GM) NOTIFIED NHTSA THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-441) TO ADDRESS A SAFETY RELATEDDEFECT THAT CAN RESULT IN ENGINE COMPARTMENT FIRE IN APPROXIMATELY 850,000 VEHICLES EQUIPPED WITH A HEATED WINDSHIELD WASHER FLUID OPTION.THE SUBJECT VEHICLES OF THIS INVESTIGATION COMPRISE OVER THREE-QUARTERS OF THE RECALL POPULATION. ACCORDING TO GM, A SHORT CIRCUIT ON THE PRINTED CIRCUIT BOARD FOR THE WINDSHIELD WASHER FLUID HEATER MODULE MAY OVERHEAT THE CONTROL-CIRCUIT GROUND WIRE. THIS MAY CAUSE OTHER ELECTRICAL FEATURES TO MALFUNCTION, CREATE AN ODOR OR CAUSE SMOKE AND IN RARE CASES IT MAY CAUSE A FIRE.AS A REMEDY, GM DEALERS WILL INSTALL A WIRE HARNESS WITH AN IN-LINE FUSE. IN ADDITION TO THE SUBJECT VEHICLES, SEVERAL OTHER GM MODELS WITH THE HEATED WINDSHIELD WASHER FLUID OPTION ARE INCLUDED IN RECALL 08V-441: MY 2006-2008 BUICK LUCERNE (MANUFACTURED AUGUST 2005 THROUGH NOVEMBER 2007); MY 2008 BUICK ENCLAVE (MANUFACTURED FEBRUARY 2007 THROUGH APRIL 2007); MY 2006-2008 CADILLAC DTS (MANUFACTURED MAY 2007 THROUGH NOVEMBER 2007); MY 2007-2008 SATURN OUTLOOK (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007); AND MY 2007-2008 GMC ACADIA (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007) VEHICLES.GM IS INSTRUCTING OWNERS TO TAKE THEIR VEHICLE TO A DEALER FOR SERVICE IF THEY EXPERIENCE SYMPTOMS OF WINDSHIELD WASHER HEATER MODULE SHORT CIRCUITS. GM'S RECALL RESOLVES THE SAFETY DEFECT CONCERNS PURSUED BY THIS INVESTIGATION.THIS ENGINEERING ANALYSIS IS CLOSED.
Electrical System:wiring:fuses And Circuit Breakers
IN A LETTER DATED AUGUST 27, 2008, GENERAL MOTORS CORP. (GM) NOTIFIED NHTSA THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-441) TO ADDRESS A SAFETY RELATEDDEFECT THAT CAN RESULT IN ENGINE COMPARTMENT FIRE IN APPROXIMATELY 850,000 VEHICLES EQUIPPED WITH A HEATED WINDSHIELD WASHER FLUID OPTION.THE SUBJECT VEHICLES OF THIS INVESTIGATION COMPRISE OVER THREE-QUARTERS OF THE RECALL POPULATION. ACCORDING TO GM, A SHORT CIRCUIT ON THE PRINTED CIRCUIT BOARD FOR THE WINDSHIELD WASHER FLUID HEATER MODULE MAY OVERHEAT THE CONTROL-CIRCUIT GROUND WIRE. THIS MAY CAUSE OTHER ELECTRICAL FEATURES TO MALFUNCTION, CREATE AN ODOR OR CAUSE SMOKE AND IN RARE CASES IT MAY CAUSE A FIRE.AS A REMEDY, GM DEALERS WILL INSTALL A WIRE HARNESS WITH AN IN-LINE FUSE. IN ADDITION TO THE SUBJECT VEHICLES, SEVERAL OTHER GM MODELS WITH THE HEATED WINDSHIELD WASHER FLUID OPTION ARE INCLUDED IN RECALL 08V-441: MY 2006-2008 BUICK LUCERNE (MANUFACTURED AUGUST 2005 THROUGH NOVEMBER 2007); MY 2008 BUICK ENCLAVE (MANUFACTURED FEBRUARY 2007 THROUGH APRIL 2007); MY 2006-2008 CADILLAC DTS (MANUFACTURED MAY 2007 THROUGH NOVEMBER 2007); MY 2007-2008 SATURN OUTLOOK (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007); AND MY 2007-2008 GMC ACADIA (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007) VEHICLES.GM IS INSTRUCTING OWNERS TO TAKE THEIR VEHICLE TO A DEALER FOR SERVICE IF THEY EXPERIENCE SYMPTOMS OF WINDSHIELD WASHER HEATER MODULE SHORT CIRCUITS. GM'S RECALL RESOLVES THE SAFETY DEFECT CONCERNS PURSUED BY THIS INVESTIGATION.THIS ENGINEERING ANALYSIS IS CLOSED.
Electrical System:wiring
IN A LETTER DATED AUGUST 27, 2008, GENERAL MOTORS CORP. (GM) NOTIFIED NHTSA THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-441) TO ADDRESS A SAFETY RELATEDDEFECT THAT CAN RESULT IN ENGINE COMPARTMENT FIRE IN APPROXIMATELY 850,000 VEHICLES EQUIPPED WITH A HEATED WINDSHIELD WASHER FLUID OPTION.THE SUBJECT VEHICLES OF THIS INVESTIGATION COMPRISE OVER THREE-QUARTERS OF THE RECALL POPULATION. ACCORDING TO GM, A SHORT CIRCUIT ON THE PRINTED CIRCUIT BOARD FOR THE WINDSHIELD WASHER FLUID HEATER MODULE MAY OVERHEAT THE CONTROL-CIRCUIT GROUND WIRE. THIS MAY CAUSE OTHER ELECTRICAL FEATURES TO MALFUNCTION, CREATE AN ODOR OR CAUSE SMOKE AND IN RARE CASES IT MAY CAUSE A FIRE.AS A REMEDY, GM DEALERS WILL INSTALL A WIRE HARNESS WITH AN IN-LINE FUSE. IN ADDITION TO THE SUBJECT VEHICLES, SEVERAL OTHER GM MODELS WITH THE HEATED WINDSHIELD WASHER FLUID OPTION ARE INCLUDED IN RECALL 08V-441: MY 2006-2008 BUICK LUCERNE (MANUFACTURED AUGUST 2005 THROUGH NOVEMBER 2007); MY 2008 BUICK ENCLAVE (MANUFACTURED FEBRUARY 2007 THROUGH APRIL 2007); MY 2006-2008 CADILLAC DTS (MANUFACTURED MAY 2007 THROUGH NOVEMBER 2007); MY 2007-2008 SATURN OUTLOOK (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007); AND MY 2007-2008 GMC ACADIA (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007) VEHICLES.GM IS INSTRUCTING OWNERS TO TAKE THEIR VEHICLE TO A DEALER FOR SERVICE IF THEY EXPERIENCE SYMPTOMS OF WINDSHIELD WASHER HEATER MODULE SHORT CIRCUITS. GM'S RECALL RESOLVES THE SAFETY DEFECT CONCERNS PURSUED BY THIS INVESTIGATION.THIS ENGINEERING ANALYSIS IS CLOSED.
Engine And Engine Cooling:engine
IN A LETTER DATED AUGUST 27, 2008, GENERAL MOTORS CORP. (GM) NOTIFIED NHTSA THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-441) TO ADDRESS A SAFETY RELATEDDEFECT THAT CAN RESULT IN ENGINE COMPARTMENT FIRE IN APPROXIMATELY 850,000 VEHICLES EQUIPPED WITH A HEATED WINDSHIELD WASHER FLUID OPTION.THE SUBJECT VEHICLES OF THIS INVESTIGATION COMPRISE OVER THREE-QUARTERS OF THE RECALL POPULATION. ACCORDING TO GM, A SHORT CIRCUIT ON THE PRINTED CIRCUIT BOARD FOR THE WINDSHIELD WASHER FLUID HEATER MODULE MAY OVERHEAT THE CONTROL-CIRCUIT GROUND WIRE. THIS MAY CAUSE OTHER ELECTRICAL FEATURES TO MALFUNCTION, CREATE AN ODOR OR CAUSE SMOKE AND IN RARE CASES IT MAY CAUSE A FIRE.AS A REMEDY, GM DEALERS WILL INSTALL A WIRE HARNESS WITH AN IN-LINE FUSE. IN ADDITION TO THE SUBJECT VEHICLES, SEVERAL OTHER GM MODELS WITH THE HEATED WINDSHIELD WASHER FLUID OPTION ARE INCLUDED IN RECALL 08V-441: MY 2006-2008 BUICK LUCERNE (MANUFACTURED AUGUST 2005 THROUGH NOVEMBER 2007); MY 2008 BUICK ENCLAVE (MANUFACTURED FEBRUARY 2007 THROUGH APRIL 2007); MY 2006-2008 CADILLAC DTS (MANUFACTURED MAY 2007 THROUGH NOVEMBER 2007); MY 2007-2008 SATURN OUTLOOK (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007); AND MY 2007-2008 GMC ACADIA (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007) VEHICLES.GM IS INSTRUCTING OWNERS TO TAKE THEIR VEHICLE TO A DEALER FOR SERVICE IF THEY EXPERIENCE SYMPTOMS OF WINDSHIELD WASHER HEATER MODULE SHORT CIRCUITS. GM'S RECALL RESOLVES THE SAFETY DEFECT CONCERNS PURSUED BY THIS INVESTIGATION.THIS ENGINEERING ANALYSIS IS CLOSED.
Engine And Engine Cooling
IN A LETTER DATED AUGUST 27, 2008, GENERAL MOTORS CORP. (GM) NOTIFIED NHTSA THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-441) TO ADDRESS A SAFETY RELATEDDEFECT THAT CAN RESULT IN ENGINE COMPARTMENT FIRE IN APPROXIMATELY 850,000 VEHICLES EQUIPPED WITH A HEATED WINDSHIELD WASHER FLUID OPTION.THE SUBJECT VEHICLES OF THIS INVESTIGATION COMPRISE OVER THREE-QUARTERS OF THE RECALL POPULATION. ACCORDING TO GM, A SHORT CIRCUIT ON THE PRINTED CIRCUIT BOARD FOR THE WINDSHIELD WASHER FLUID HEATER MODULE MAY OVERHEAT THE CONTROL-CIRCUIT GROUND WIRE. THIS MAY CAUSE OTHER ELECTRICAL FEATURES TO MALFUNCTION, CREATE AN ODOR OR CAUSE SMOKE AND IN RARE CASES IT MAY CAUSE A FIRE.AS A REMEDY, GM DEALERS WILL INSTALL A WIRE HARNESS WITH AN IN-LINE FUSE. IN ADDITION TO THE SUBJECT VEHICLES, SEVERAL OTHER GM MODELS WITH THE HEATED WINDSHIELD WASHER FLUID OPTION ARE INCLUDED IN RECALL 08V-441: MY 2006-2008 BUICK LUCERNE (MANUFACTURED AUGUST 2005 THROUGH NOVEMBER 2007); MY 2008 BUICK ENCLAVE (MANUFACTURED FEBRUARY 2007 THROUGH APRIL 2007); MY 2006-2008 CADILLAC DTS (MANUFACTURED MAY 2007 THROUGH NOVEMBER 2007); MY 2007-2008 SATURN OUTLOOK (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007); AND MY 2007-2008 GMC ACADIA (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007) VEHICLES.GM IS INSTRUCTING OWNERS TO TAKE THEIR VEHICLE TO A DEALER FOR SERVICE IF THEY EXPERIENCE SYMPTOMS OF WINDSHIELD WASHER HEATER MODULE SHORT CIRCUITS. GM'S RECALL RESOLVES THE SAFETY DEFECT CONCERNS PURSUED BY THIS INVESTIGATION.THIS ENGINEERING ANALYSIS IS CLOSED.
Visibility:windshield Wiper/washer
IN A LETTER DATED AUGUST 27, 2008, GENERAL MOTORS CORP. (GM) NOTIFIED NHTSA THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-441) TO ADDRESS A SAFETY RELATEDDEFECT THAT CAN RESULT IN ENGINE COMPARTMENT FIRE IN APPROXIMATELY 850,000 VEHICLES EQUIPPED WITH A HEATED WINDSHIELD WASHER FLUID OPTION.THE SUBJECT VEHICLES OF THIS INVESTIGATION COMPRISE OVER THREE-QUARTERS OF THE RECALL POPULATION. ACCORDING TO GM, A SHORT CIRCUIT ON THE PRINTED CIRCUIT BOARD FOR THE WINDSHIELD WASHER FLUID HEATER MODULE MAY OVERHEAT THE CONTROL-CIRCUIT GROUND WIRE. THIS MAY CAUSE OTHER ELECTRICAL FEATURES TO MALFUNCTION, CREATE AN ODOR OR CAUSE SMOKE AND IN RARE CASES IT MAY CAUSE A FIRE.AS A REMEDY, GM DEALERS WILL INSTALL A WIRE HARNESS WITH AN IN-LINE FUSE. IN ADDITION TO THE SUBJECT VEHICLES, SEVERAL OTHER GM MODELS WITH THE HEATED WINDSHIELD WASHER FLUID OPTION ARE INCLUDED IN RECALL 08V-441: MY 2006-2008 BUICK LUCERNE (MANUFACTURED AUGUST 2005 THROUGH NOVEMBER 2007); MY 2008 BUICK ENCLAVE (MANUFACTURED FEBRUARY 2007 THROUGH APRIL 2007); MY 2006-2008 CADILLAC DTS (MANUFACTURED MAY 2007 THROUGH NOVEMBER 2007); MY 2007-2008 SATURN OUTLOOK (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007); AND MY 2007-2008 GMC ACADIA (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007) VEHICLES.GM IS INSTRUCTING OWNERS TO TAKE THEIR VEHICLE TO A DEALER FOR SERVICE IF THEY EXPERIENCE SYMPTOMS OF WINDSHIELD WASHER HEATER MODULE SHORT CIRCUITS. GM'S RECALL RESOLVES THE SAFETY DEFECT CONCERNS PURSUED BY THIS INVESTIGATION.THIS ENGINEERING ANALYSIS IS CLOSED.
Visibility:windshield Wiper/washer:switch/wiring
IN A LETTER DATED AUGUST 27, 2008, GENERAL MOTORS CORP. (GM) NOTIFIED NHTSA THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-441) TO ADDRESS A SAFETY RELATEDDEFECT THAT CAN RESULT IN ENGINE COMPARTMENT FIRE IN APPROXIMATELY 850,000 VEHICLES EQUIPPED WITH A HEATED WINDSHIELD WASHER FLUID OPTION.THE SUBJECT VEHICLES OF THIS INVESTIGATION COMPRISE OVER THREE-QUARTERS OF THE RECALL POPULATION. ACCORDING TO GM, A SHORT CIRCUIT ON THE PRINTED CIRCUIT BOARD FOR THE WINDSHIELD WASHER FLUID HEATER MODULE MAY OVERHEAT THE CONTROL-CIRCUIT GROUND WIRE. THIS MAY CAUSE OTHER ELECTRICAL FEATURES TO MALFUNCTION, CREATE AN ODOR OR CAUSE SMOKE AND IN RARE CASES IT MAY CAUSE A FIRE.AS A REMEDY, GM DEALERS WILL INSTALL A WIRE HARNESS WITH AN IN-LINE FUSE. IN ADDITION TO THE SUBJECT VEHICLES, SEVERAL OTHER GM MODELS WITH THE HEATED WINDSHIELD WASHER FLUID OPTION ARE INCLUDED IN RECALL 08V-441: MY 2006-2008 BUICK LUCERNE (MANUFACTURED AUGUST 2005 THROUGH NOVEMBER 2007); MY 2008 BUICK ENCLAVE (MANUFACTURED FEBRUARY 2007 THROUGH APRIL 2007); MY 2006-2008 CADILLAC DTS (MANUFACTURED MAY 2007 THROUGH NOVEMBER 2007); MY 2007-2008 SATURN OUTLOOK (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007); AND MY 2007-2008 GMC ACADIA (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007) VEHICLES.GM IS INSTRUCTING OWNERS TO TAKE THEIR VEHICLE TO A DEALER FOR SERVICE IF THEY EXPERIENCE SYMPTOMS OF WINDSHIELD WASHER HEATER MODULE SHORT CIRCUITS. GM'S RECALL RESOLVES THE SAFETY DEFECT CONCERNS PURSUED BY THIS INVESTIGATION.THIS ENGINEERING ANALYSIS IS CLOSED.
PE08010 · NON-CRASH Engine Compartment Fires
Opened Feb 4, 2008 · Closed Jun 12, 2008
Status: closed (inferred from source dates) · Electrical System; Electrical SYSTEM:12V/24V/48V Battery; Electrical SYSTEM:12V/24V/48V Battery:cables; Electrical System:wiring; Electrical System:wiring:front Underhood; Engine And Engine Cooling; Engine And Engine Cooling:engine
IN RESPONSE TO AN INFORMATION REQUEST LETTER SENT BY THE OFFICE OF DEFECTS INVESTIGATION(ODI) DURING PRELIMINARY EVALUATION PE08-010, GM PROVIDED ODI WITH 41 ALLEGATIONS OF NON-CRASH ENGINE COMPARTMENT FIRES INCLUDING 16 ALLEGATIONS OF FIRES ORIGINATING WITH THE IGNITION IN THE OFF POSITION.ONE OF THE FIRES WAS DETERMINED TO BE CAUSED BY AN ARSON EVENT.ODI HAS ALSO RECEIVED 5 REPORTS, 4 OF WHICH ARE OF DUPLICATIVE OF REPORTS PROVIDED BY GM, ALLEGING NON-CRASH ENGINE COMPARTMENT FIRES IN THE SUBJECT VEHICLES.IN TOTAL, ODI IS AWARE OF 41 NON-CRASHENGINE COMPARTMENT FIRES IN THE SUBJECT VEHICLES THAT ARE UNRELATED TO ARSON.EIGHT OF THE 41 FIRE ALLEGATIONS ALSO ALLEGE PROPERTY DAMAGE AS A RESULT OF THE FIRES.THIS PRELIMINARY EVALUATION HAS BEEN UPGRADED TO AN ENGINEERING ANALYSIS (EA08-010) TO FURTHER ASSESS THE SCOPE, FREQUENCY, ORIGIN AND CAUSE OF THE ALLEGED NON-CRASH RELATED ENGINE COMPARTMENT FIRES IN THE SUBJECT VEHICLES.
Additional source detail variants (7)
Electrical SYSTEM:12V/24V/48V Battery:cables
IN RESPONSE TO AN INFORMATION REQUEST LETTER SENT BY THE OFFICE OF DEFECTS INVESTIGATION(ODI) DURING PRELIMINARY EVALUATION PE08-010, GM PROVIDED ODI WITH 41 ALLEGATIONS OF NON-CRASH ENGINE COMPARTMENT FIRES INCLUDING 16 ALLEGATIONS OF FIRES ORIGINATING WITH THE IGNITION IN THE OFF POSITION.ONE OF THE FIRES WAS DETERMINED TO BE CAUSED BY AN ARSON EVENT.ODI HAS ALSO RECEIVED 5 REPORTS, 4 OF WHICH ARE OF DUPLICATIVE OF REPORTS PROVIDED BY GM, ALLEGING NON-CRASH ENGINE COMPARTMENT FIRES IN THE SUBJECT VEHICLES.IN TOTAL, ODI IS AWARE OF 41 NON-CRASHENGINE COMPARTMENT FIRES IN THE SUBJECT VEHICLES THAT ARE UNRELATED TO ARSON.EIGHT OF THE 41 FIRE ALLEGATIONS ALSO ALLEGE PROPERTY DAMAGE AS A RESULT OF THE FIRES.THIS PRELIMINARY EVALUATION HAS BEEN UPGRADED TO AN ENGINEERING ANALYSIS (EA08-010) TO FURTHER ASSESS THE SCOPE, FREQUENCY, ORIGIN AND CAUSE OF THE ALLEGED NON-CRASH RELATED ENGINE COMPARTMENT FIRES IN THE SUBJECT VEHICLES.
Electrical SYSTEM:12V/24V/48V Battery
IN RESPONSE TO AN INFORMATION REQUEST LETTER SENT BY THE OFFICE OF DEFECTS INVESTIGATION(ODI) DURING PRELIMINARY EVALUATION PE08-010, GM PROVIDED ODI WITH 41 ALLEGATIONS OF NON-CRASH ENGINE COMPARTMENT FIRES INCLUDING 16 ALLEGATIONS OF FIRES ORIGINATING WITH THE IGNITION IN THE OFF POSITION.ONE OF THE FIRES WAS DETERMINED TO BE CAUSED BY AN ARSON EVENT.ODI HAS ALSO RECEIVED 5 REPORTS, 4 OF WHICH ARE OF DUPLICATIVE OF REPORTS PROVIDED BY GM, ALLEGING NON-CRASH ENGINE COMPARTMENT FIRES IN THE SUBJECT VEHICLES.IN TOTAL, ODI IS AWARE OF 41 NON-CRASHENGINE COMPARTMENT FIRES IN THE SUBJECT VEHICLES THAT ARE UNRELATED TO ARSON.EIGHT OF THE 41 FIRE ALLEGATIONS ALSO ALLEGE PROPERTY DAMAGE AS A RESULT OF THE FIRES.THIS PRELIMINARY EVALUATION HAS BEEN UPGRADED TO AN ENGINEERING ANALYSIS (EA08-010) TO FURTHER ASSESS THE SCOPE, FREQUENCY, ORIGIN AND CAUSE OF THE ALLEGED NON-CRASH RELATED ENGINE COMPARTMENT FIRES IN THE SUBJECT VEHICLES.
Electrical System
IN RESPONSE TO AN INFORMATION REQUEST LETTER SENT BY THE OFFICE OF DEFECTS INVESTIGATION(ODI) DURING PRELIMINARY EVALUATION PE08-010, GM PROVIDED ODI WITH 41 ALLEGATIONS OF NON-CRASH ENGINE COMPARTMENT FIRES INCLUDING 16 ALLEGATIONS OF FIRES ORIGINATING WITH THE IGNITION IN THE OFF POSITION.ONE OF THE FIRES WAS DETERMINED TO BE CAUSED BY AN ARSON EVENT.ODI HAS ALSO RECEIVED 5 REPORTS, 4 OF WHICH ARE OF DUPLICATIVE OF REPORTS PROVIDED BY GM, ALLEGING NON-CRASH ENGINE COMPARTMENT FIRES IN THE SUBJECT VEHICLES.IN TOTAL, ODI IS AWARE OF 41 NON-CRASHENGINE COMPARTMENT FIRES IN THE SUBJECT VEHICLES THAT ARE UNRELATED TO ARSON.EIGHT OF THE 41 FIRE ALLEGATIONS ALSO ALLEGE PROPERTY DAMAGE AS A RESULT OF THE FIRES.THIS PRELIMINARY EVALUATION HAS BEEN UPGRADED TO AN ENGINEERING ANALYSIS (EA08-010) TO FURTHER ASSESS THE SCOPE, FREQUENCY, ORIGIN AND CAUSE OF THE ALLEGED NON-CRASH RELATED ENGINE COMPARTMENT FIRES IN THE SUBJECT VEHICLES.
Electrical System:wiring:front Underhood
IN RESPONSE TO AN INFORMATION REQUEST LETTER SENT BY THE OFFICE OF DEFECTS INVESTIGATION(ODI) DURING PRELIMINARY EVALUATION PE08-010, GM PROVIDED ODI WITH 41 ALLEGATIONS OF NON-CRASH ENGINE COMPARTMENT FIRES INCLUDING 16 ALLEGATIONS OF FIRES ORIGINATING WITH THE IGNITION IN THE OFF POSITION.ONE OF THE FIRES WAS DETERMINED TO BE CAUSED BY AN ARSON EVENT.ODI HAS ALSO RECEIVED 5 REPORTS, 4 OF WHICH ARE OF DUPLICATIVE OF REPORTS PROVIDED BY GM, ALLEGING NON-CRASH ENGINE COMPARTMENT FIRES IN THE SUBJECT VEHICLES.IN TOTAL, ODI IS AWARE OF 41 NON-CRASHENGINE COMPARTMENT FIRES IN THE SUBJECT VEHICLES THAT ARE UNRELATED TO ARSON.EIGHT OF THE 41 FIRE ALLEGATIONS ALSO ALLEGE PROPERTY DAMAGE AS A RESULT OF THE FIRES.THIS PRELIMINARY EVALUATION HAS BEEN UPGRADED TO AN ENGINEERING ANALYSIS (EA08-010) TO FURTHER ASSESS THE SCOPE, FREQUENCY, ORIGIN AND CAUSE OF THE ALLEGED NON-CRASH RELATED ENGINE COMPARTMENT FIRES IN THE SUBJECT VEHICLES.
Electrical System:wiring
IN RESPONSE TO AN INFORMATION REQUEST LETTER SENT BY THE OFFICE OF DEFECTS INVESTIGATION(ODI) DURING PRELIMINARY EVALUATION PE08-010, GM PROVIDED ODI WITH 41 ALLEGATIONS OF NON-CRASH ENGINE COMPARTMENT FIRES INCLUDING 16 ALLEGATIONS OF FIRES ORIGINATING WITH THE IGNITION IN THE OFF POSITION.ONE OF THE FIRES WAS DETERMINED TO BE CAUSED BY AN ARSON EVENT.ODI HAS ALSO RECEIVED 5 REPORTS, 4 OF WHICH ARE OF DUPLICATIVE OF REPORTS PROVIDED BY GM, ALLEGING NON-CRASH ENGINE COMPARTMENT FIRES IN THE SUBJECT VEHICLES.IN TOTAL, ODI IS AWARE OF 41 NON-CRASHENGINE COMPARTMENT FIRES IN THE SUBJECT VEHICLES THAT ARE UNRELATED TO ARSON.EIGHT OF THE 41 FIRE ALLEGATIONS ALSO ALLEGE PROPERTY DAMAGE AS A RESULT OF THE FIRES.THIS PRELIMINARY EVALUATION HAS BEEN UPGRADED TO AN ENGINEERING ANALYSIS (EA08-010) TO FURTHER ASSESS THE SCOPE, FREQUENCY, ORIGIN AND CAUSE OF THE ALLEGED NON-CRASH RELATED ENGINE COMPARTMENT FIRES IN THE SUBJECT VEHICLES.
Engine And Engine Cooling:engine
IN RESPONSE TO AN INFORMATION REQUEST LETTER SENT BY THE OFFICE OF DEFECTS INVESTIGATION(ODI) DURING PRELIMINARY EVALUATION PE08-010, GM PROVIDED ODI WITH 41 ALLEGATIONS OF NON-CRASH ENGINE COMPARTMENT FIRES INCLUDING 16 ALLEGATIONS OF FIRES ORIGINATING WITH THE IGNITION IN THE OFF POSITION.ONE OF THE FIRES WAS DETERMINED TO BE CAUSED BY AN ARSON EVENT.ODI HAS ALSO RECEIVED 5 REPORTS, 4 OF WHICH ARE OF DUPLICATIVE OF REPORTS PROVIDED BY GM, ALLEGING NON-CRASH ENGINE COMPARTMENT FIRES IN THE SUBJECT VEHICLES.IN TOTAL, ODI IS AWARE OF 41 NON-CRASHENGINE COMPARTMENT FIRES IN THE SUBJECT VEHICLES THAT ARE UNRELATED TO ARSON.EIGHT OF THE 41 FIRE ALLEGATIONS ALSO ALLEGE PROPERTY DAMAGE AS A RESULT OF THE FIRES.THIS PRELIMINARY EVALUATION HAS BEEN UPGRADED TO AN ENGINEERING ANALYSIS (EA08-010) TO FURTHER ASSESS THE SCOPE, FREQUENCY, ORIGIN AND CAUSE OF THE ALLEGED NON-CRASH RELATED ENGINE COMPARTMENT FIRES IN THE SUBJECT VEHICLES.
Engine And Engine Cooling
IN RESPONSE TO AN INFORMATION REQUEST LETTER SENT BY THE OFFICE OF DEFECTS INVESTIGATION(ODI) DURING PRELIMINARY EVALUATION PE08-010, GM PROVIDED ODI WITH 41 ALLEGATIONS OF NON-CRASH ENGINE COMPARTMENT FIRES INCLUDING 16 ALLEGATIONS OF FIRES ORIGINATING WITH THE IGNITION IN THE OFF POSITION.ONE OF THE FIRES WAS DETERMINED TO BE CAUSED BY AN ARSON EVENT.ODI HAS ALSO RECEIVED 5 REPORTS, 4 OF WHICH ARE OF DUPLICATIVE OF REPORTS PROVIDED BY GM, ALLEGING NON-CRASH ENGINE COMPARTMENT FIRES IN THE SUBJECT VEHICLES.IN TOTAL, ODI IS AWARE OF 41 NON-CRASHENGINE COMPARTMENT FIRES IN THE SUBJECT VEHICLES THAT ARE UNRELATED TO ARSON.EIGHT OF THE 41 FIRE ALLEGATIONS ALSO ALLEGE PROPERTY DAMAGE AS A RESULT OF THE FIRES.THIS PRELIMINARY EVALUATION HAS BEEN UPGRADED TO AN ENGINEERING ANALYSIS (EA08-010) TO FURTHER ASSESS THE SCOPE, FREQUENCY, ORIGIN AND CAUSE OF THE ALLEGED NON-CRASH RELATED ENGINE COMPARTMENT FIRES IN THE SUBJECT VEHICLES.