IllustrationEngine suddenly stopped running while driving and could not be restarted. It was towed to a local diesel repair shop. Diagnostics showed a catastrophic failure of the high pressure fuel pump which polluted the complete fuel system with metal.
2011 Chevrolet Silverado 2500
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2011 Chevrolet Silverado 2500 do not stand out strongly from the model-year median of 81.
About this comparison →How this year compares
Owner complaints by model year
Compare all Silverado 2500 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
150–25K
725–50K
750–75K
1475–100K
9100–150K
5150K+
57 reports with mileage · 47 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Air Bags. Review the 40 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Power Train. Review the 10 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 9 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
2 crash reports2 fire reports2 injury reports
Fuel/propulsion System complaints
8 reportsFuel pump fuse socket has melted in addition to fuse being blown. Fuel pump had been replaced twice with OEM fuel pump. Entire fuse box must be replaced. Occasionally, a no start condition can be traced to fuse contacts losing conductivity which can be resolved by removing them reinstalling fuse. Has potential of causing electri…
Read full complaint
Fuel pump fuse socket has melted in addition to fuse being blown. Fuel pump had been replaced twice with OEM fuel pump. Entire fuse box must be replaced. Occasionally, a no start condition can be traced to fuse contacts losing conductivity which can be resolved by removing them reinstalling fuse. Has potential of causing electrical fire
WHILE DRIVING IN EXCESS OF 55 MPH ON I 95, MY 2011 CHEVROLET SILVERADO 2500 STALLED WITHOUT WARNING WHILE I WAS IN THE FAR LEFT PASSING LANE. NO POWER STEERING OR POWER BRAKES MADE IT EXTREMELY DIFFICULT TO CONTROL WHILE MOVING THROUGH 4 LANES OF TRAFFIC TO GET TO THE SHOULDER. I WAS UNABLE TO RESTART THE VEHICLE AND HAD TO HA…
Read full complaint
WHILE DRIVING IN EXCESS OF 55 MPH ON I 95, MY 2011 CHEVROLET SILVERADO 2500 STALLED WITHOUT WARNING WHILE I WAS IN THE FAR LEFT PASSING LANE. NO POWER STEERING OR POWER BRAKES MADE IT EXTREMELY DIFFICULT TO CONTROL WHILE MOVING THROUGH 4 LANES OF TRAFFIC TO GET TO THE SHOULDER. I WAS UNABLE TO RESTART THE VEHICLE AND HAD TO HAVE IT TOWED TO A GARAGE. I WAS INFORMED THE CP4 FUEL INJECTION PUMP HAD FAILED AND REPAIRS WILL BE IN EXCESS OF $8,000 BECAUSE THE ENTIRE FUEL DELIVERY SYSTEM WAS CONTAMINATED AND NEEDS TO BE REPLACED.
I HAVE A 2011 CHEVY 2500. 6.6 TURBO DIESEL AT 136K MILES. MY DEF HEATER JUST WENT OUT AND MY DEALERSHIP SAID IT'S ONLY UNDER WARRANTY UNTIL 120K MILES. I'VE BEEN LOOKING ONLINE AND THERE'S A LOT OF 2011S THAT ARE HAVING THE SAME PROBLEM. SOMEONE NEEDS TO STEP UP AND BE RESPONSIBLE FOR THIS. IT'S COSTING ME $1200 TO FIX PLUS A DA…
Read full complaint
I HAVE A 2011 CHEVY 2500. 6.6 TURBO DIESEL AT 136K MILES. MY DEF HEATER JUST WENT OUT AND MY DEALERSHIP SAID IT'S ONLY UNDER WARRANTY UNTIL 120K MILES. I'VE BEEN LOOKING ONLINE AND THERE'S A LOT OF 2011S THAT ARE HAVING THE SAME PROBLEM. SOMEONE NEEDS TO STEP UP AND BE RESPONSIBLE FOR THIS. IT'S COSTING ME $1200 TO FIX PLUS A DAY OFF WORK. I'M SELF EMPLOYED AND IF I SELL A FAULTY PRODUCT I'M REQUIRED TO REPLACE FOR FREE. G.M SHOULD BE DOING THE SAME.
TL* THE CONTACT OWNS A 2011 CHEVROLET SILVERADO 2500. WHILE DRIVING APPROXIMATELY 35 MPH, THE VEHICLE STALLED. THE CONTACT COASTED THE VEHICLE TO THE SIDE OF THE ROAD. THERE WERE NO WARNING INDICATORS ILLUMINATED. THE VEHICLE WAS TOWED TO THE CONTACT'S RESIDENCE AND THEN TOWED TO BOMNIN CHEVROLET (8455 S DIXIE HWY, MIAMI, FL 331…
Read full complaint
TL* THE CONTACT OWNS A 2011 CHEVROLET SILVERADO 2500. WHILE DRIVING APPROXIMATELY 35 MPH, THE VEHICLE STALLED. THE CONTACT COASTED THE VEHICLE TO THE SIDE OF THE ROAD. THERE WERE NO WARNING INDICATORS ILLUMINATED. THE VEHICLE WAS TOWED TO THE CONTACT'S RESIDENCE AND THEN TOWED TO BOMNIN CHEVROLET (8455 S DIXIE HWY, MIAMI, FL 33143). THE DEALER DIAGNOSED THAT THE CP4 FUEL PUMP FAILED AND NEEDED REPLACEMENT. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE VEHICLE WAS NOT REPAIRED. THE APPROXIMATE FAILURE MILEAGE WAS 123,000.
AN ARTICLE IN TRAILER LIFE (MAY, 2019) IDENTIFIED THAT THE BOSCH CP4.2 HIGH-PRESSURE FUEL-INJECTION PUMP IS SUBJECT TO CATASTROPHIC FAILURE. IT POINTS OUT THIS IS A COMMON FAILURE, A DESIGN ISSUE AND WILL COST MANY $1000'S TO REPAIR. IT HAS BEEN CALLED A "FATAL FLAW". IT SHOULD BE REPLACED WITH A UNIT THAT IS RELIABLE BY THE MAN…
Read full complaint
AN ARTICLE IN TRAILER LIFE (MAY, 2019) IDENTIFIED THAT THE BOSCH CP4.2 HIGH-PRESSURE FUEL-INJECTION PUMP IS SUBJECT TO CATASTROPHIC FAILURE. IT POINTS OUT THIS IS A COMMON FAILURE, A DESIGN ISSUE AND WILL COST MANY $1000'S TO REPAIR. IT HAS BEEN CALLED A "FATAL FLAW". IT SHOULD BE REPLACED WITH A UNIT THAT IS RELIABLE BY THE MANUFACTURER IF THIS IS A COMMON PROBLEM. MICHIGAN S&S MOTORSPORT STATES THIS IS A KNOWN PROBLEM AND IS COMMON TO 2011 TO 2016 DURAMAX DIESEL SILVERADOS USING THE BOSCH CP4.2 FUEL-INJECTION PUMP.
EXHAUST MANIFOLD BOLTS ARE BREAKING DESPITE REGULAR NON COMMERCIAL USE AND PROPER MAINTENANCE. THIS CAUSES AN EXHAUST LEAK AND I AM NOT COMFORTABLE DRIVING MY INFANT IN THE TRUCK NOW. DEALER SAYS 4 HOW ODD LABOR PLUS PARTS SO APPROX $1000 FIX? THAT'S UNREASONABLE FOR ANY MOTOR BUT ESPECIALLY UNDER 120000KM.
THE TRUCK HAD THE CHECK ENGINE LIGHT COME ON WHEN WE TOOK IT TO THE DEALERSHIP THEY REPLACE THE FUEL PRESSURE REGULATOR. THE LIGHT SOON CAME BACK ON DUE TO A FAULTY FUEL PUMP WHICH SENT THE CAR INTO SAFE MODE, WHICH MADE THE CAR DO A NOSE DIVE FROM 55 TO 15 IN A MATTER OF SECONDS ON A MAJOR INTERSTATE IN ATLANTA. *JS
Official recalls
421V050000 · Air Bags:frontal:passenger Side:inflator Module
Feb 5, 2021
General Motors, LLC (GM) is recalling certain 2007-2011 Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado 1500, Suburban, Tahoe, GMC Sierra 1500, Yukon, Yukon XL, and 2009-2011 Chevrolet Silverado 2500, Silverado 3500, GMC Sierra 2500 and Sierra 3500 vehicles originally sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, GM is recalling certain 2007-2008 Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado 1500, Suburban, Tahoe, GMC Sierra 1500, Yukon, Yukon XL vehicles originally sold, or ever registered, in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." These vehicles are equipped with non-desiccated passenger frontal inflators containing phase-stabilized ammonium nitrate (PSAN) propellant. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 22, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed on March 1, 2021. Owners may contact Chevrolet customer service at 1-800-222-1020; Cadillac customer service at 1-800-458-8006; and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328760.
21V054000 · Air Bags:frontal:passenger Side:inflator Module
Feb 5, 2021
General Motors, LLC (GM) is recalling certain 2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of AL, CA, FL, GA, HI, LA, MS, SC, TX, PR, AS, GU, the MP, and VI or "Zone A." Additionally GM is recalling certain 2011-2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, Yukon XL and 2011-2013 Cadillac Escalade EXT, Chevrolet Avalanche, Silverado 1500, and GMC Sierra 1500 vehicles originally sold, or ever registered, in the states of AZ, AR, DE, DC, IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV or "Zone B." Additionally, GM is recalling certain 2010-2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, and Yukon XL and 2010-2013 Cadillac Escalade EXT, Chevrolet Avalanche, Silverado 1500, and GMC Sierra 1500 vehicles originally sold, or ever registered, in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY or "Zone C." These vehicles are equipped with non-desiccated passenger frontal inflators containing phase-stabilized ammonium nitrate (PSAN) propellant. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 25, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed to 40 VIN owners on May 11, 2021. A second owner notification letter was mailed to all other owners on January 24, 2022. Owners may contact Chevrolet customer service at 1-800-222-1020; Cadillac customer service at 1-800-458-8006; and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328800.
18V267000 · Equipment
Apr 26, 2018
General Motors LLC (GM) is recalling certain 2009-2014 Chevrolet Silverado HD and GMC Sierra HD, 2009 GMC Topkick 5000, 6000, 7000 and 8000 Series and Isuzu F Series, and 2009-2018 Chevrolet Express, and GMC Savana vehicles, equipped with certain Plastic-Handle Fire Extinguishers or Push Button 'Pindicator' Fire Extinguishers. These extinguishers may become clogged, preventing the extinguisher from discharging as expected or requiring excessive force to activate the extinguisher. Additionally, in certain models, the nozzle may detach from the valve assembly with enough force that it could cause injury and also render the product inoperable. For a full list of the affected fire extinguisher models visit: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17E062-5427.pdf
Consequence & remedy
Consequence: In the event of a fire, if the fire extinguisher does not function properly, it can increase the risk of injury.
Remedy: GM will notify owners, instructing them to contact Kidde to get a replacement fire extinguisher, free of charge. The recall began June 11, 2018. Owners may contact Chevrolet customer service at 1-800-222-1020, GMC customer service at 1-800-462-8782, and Isuzu customer service at 1-866-441-9638. GM's number for this recall is 18146.
14V407000 · Electrical System
Jul 2, 2014
General Motors LLC (GM) is recalling certain model year 2007-2011 Chevrolet Silverado HD 2500/3500 trucks manufactured January 18, 2007, to June 22, 2011, and GMC Sierra HD 2500/3500 trucks manufactured January 22, 2007, to June 21, 2011, and equipped with an auxiliary battery. Owners may unknowingly draw too much current through the vehicle's trailer harness resulting in the melting of fusible link for the auxiliary battery.
Consequence & remedy
Consequence: If the fusible link melts it may come into contact with adjacent components, damage the electrical center cover, the nearby wiring harness conduit and other vehicle components, increasing the risk of a fire.
Remedy: GM will notify owners and dealers will replace the jumper harness with one that includes a 40 amp inline fuse, and provide the owner with supplemental Owner Manual information, free of charge. The recall began on August 29, 2014. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-800-462-8782. GM's number for this recall is 14260.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.