2021 Chevrolet Silverado 1500

Power Train:automatic Transmission:fluid/lubricant:valves/valve Body

General Motors, LLC is recalling certain 2020 Chevrolet Silverado 2500, 3500, GMC Sierra 2500, 3500, and 2020-2022 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles that may have been repaired incorrectly under recall 24V797. The transmission control valve may fail and cause the rear wheels to lock up.

Consequence: Rear wheel lock up increases the risk of a crash.

Remedy: Dealers will inspect the vehicles and update the transmission control software, free of charge. Owner notification letters were mailed March 6, 2026. Owners may contact GMC customer service at 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N252516560. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on February 12, 2026.

Power Train:automatic Transmission:control Module:software

General Motors, LLC is recalling certain 2020 Chevrolet Silverado 2500, 3500, GMC Sierra 2500, 3500, and 2020-2022 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles that may have been repaired incorrectly under recall 24V797. The transmission control valve may fail and cause the rear wheels to lock up.

Consequence: Rear wheel lock up increases the risk of a crash.

Remedy: Dealers will inspect the vehicles and update the transmission control software, free of charge. Owner notification letters were mailed March 6, 2026. Owners may contact GMC customer service at 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N252516560. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on February 12, 2026.

Power Train:automatic Transmission:fluid/lubricant:valves/valve Body

General Motors, LLC (GM) is recalling certain 2020-2022 Chevrolet Silverado 1500, 2500, 3500, GMC Sierra 1500, 2500, 3500, 2021 Cadillac Escalade, Escalade ESV, Chevrolet Tahoe, Suburban, GMC Yukon, and Yukon XL vehicles equipped with diesel engines. The transmission control valve may fail and cause the rear wheels to lock-up.

Consequence: Rear wheel lock-up can increase the risk of a crash.

Remedy: Dealers will install new transmission control module software, free of charge. GM will provide a special coverage program to cover the repair of transmissions that are identified by the remedy software as containing a defective control valve. Owner notification letters were mailed December 12, 2024. Owners may contact GM customer service at 1-888-988-7267, Cadillac customer service at 1-800-458-8006, GMC customer service at GMC 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N242454440.

Power Train:automatic Transmission:control Module:software

General Motors, LLC (GM) is recalling certain 2020-2022 Chevrolet Silverado 1500, 2500, 3500, GMC Sierra 1500, 2500, 3500, 2021 Cadillac Escalade, Escalade ESV, Chevrolet Tahoe, Suburban, GMC Yukon, and Yukon XL vehicles equipped with diesel engines. The transmission control valve may fail and cause the rear wheels to lock-up.

Consequence: Rear wheel lock-up can increase the risk of a crash.

Remedy: Dealers will install new transmission control module software, free of charge. GM will provide a special coverage program to cover the repair of transmissions that are identified by the remedy software as containing a defective control valve. Owner notification letters were mailed December 12, 2024. Owners may contact GM customer service at 1-888-988-7267, Cadillac customer service at 1-800-458-8006, GMC customer service at GMC 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N242454440.

Seat Belts:critical Fasteners

General Motors, LLC (GM) is recalling certain 2020 Chevrolet Bolt EV and 2021 GMC Canyon and Sierra 1500, 2500 and 3500, Yukon, Yukon XL, Cadillac Escalade and Escalade ESV and Chevrolet Blazer, Camaro, Colorado, Equinox, Silverado 1500, 2500 and 3500, Suburban and Tahoe vehicles. Incorrect bolts may have been used at one or more fastening locations to secure the seat belts to the vehicle. If an incorrect bolt was used, the seat belt may not be properly attached to the vehicle.

Consequence: If a seat belt assembly is not properly attached to the vehicle, the seat belt may not properly restrain an occupant in the event of a crash, increasing the risk of injury.

Remedy: GM will notify owners, and dealers will replace the suspect bolts, free of charge. The recall began January 29, 2021. Owners may contact GMC customer service at 1-800-462-8785, Cadillac customer service at 1-800-458-8006, or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202322230.

Seat Belts

General Motors, LLC (GM) is recalling certain 2020 Chevrolet Bolt EV and 2021 GMC Canyon and Sierra 1500, 2500 and 3500, Yukon, Yukon XL, Cadillac Escalade and Escalade ESV and Chevrolet Blazer, Camaro, Colorado, Equinox, Silverado 1500, 2500 and 3500, Suburban and Tahoe vehicles. Incorrect bolts may have been used at one or more fastening locations to secure the seat belts to the vehicle. If an incorrect bolt was used, the seat belt may not be properly attached to the vehicle.

Consequence: If a seat belt assembly is not properly attached to the vehicle, the seat belt may not properly restrain an occupant in the event of a crash, increasing the risk of injury.

Remedy: GM will notify owners, and dealers will replace the suspect bolts, free of charge. The recall began January 29, 2021. Owners may contact GMC customer service at 1-800-462-8785, Cadillac customer service at 1-800-458-8006, or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202322230.

Seat Belts:critical Fasteners

General Motors, LLC (GM) is recalling certain 2019-2021 Chevrolet Silverado 1500 and GMC Sierra 1500, 2021 Chevrolet Suburban and Tahoe and GMC Yukon XL and 2020-2021 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles. The seat belt brackets may not be secured to the seat frame in the front-row center seating position.

Consequence: If a seat-belt bracket is not secured, the seat belt may not properly restrain an occupant in the front-row center seat position, increasing the risk of injury in a crash.

Remedy: GM will notify owners, and dealers will inspect left-side and right-side front-row center seat-belt bracket attachments and reassemble it correctly as necessary, free of charge. The recall began January 26, 2021. Owners may contact GMC customer service at 1-800-462-8782, Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202314670.

Seat Belts

General Motors, LLC (GM) is recalling certain 2019-2021 Chevrolet Silverado 1500 and GMC Sierra 1500, 2021 Chevrolet Suburban and Tahoe and GMC Yukon XL and 2020-2021 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles. The seat belt brackets may not be secured to the seat frame in the front-row center seating position.

Consequence: If a seat-belt bracket is not secured, the seat belt may not properly restrain an occupant in the front-row center seat position, increasing the risk of injury in a crash.

Remedy: GM will notify owners, and dealers will inspect left-side and right-side front-row center seat-belt bracket attachments and reassemble it correctly as necessary, free of charge. The recall began January 26, 2021. Owners may contact GMC customer service at 1-800-462-8782, Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202314670.

Engine And Engine Cooling:engine:hard Parts Internal/mechanical

The Office of Defects Investigation (ODI) has received 1,157 reports of engine bearing failure failures in the L87 6.2L engine produced by General Motors (GM). Of the 1,157 reports received, 173 are outside of the scope of recall 25V-274. These engines are installed in Model Years (MY) 2019–2024 Chevrolet Silverado 1500 and GMC Sierra 1500, and 2021-2024MY Chevrolet Suburban and Tahoe, GMC Yukon/Yukon XL, and Cadillac Escalade/Escalade ESV vehicles. The subject engine failures were investigated as part of a Preliminary Evaluation (PE25001).  GM determined that these engine failures were due to multiple supplier manufacturing and quality issues. GM issued recall 25V-274 to address the supplier manufacturing and quality issues produced between March 1, 2021, and May 31, 2024. Based on the issuance of recall 25V-274, NHTSA has closed PE25001. ODI continues to receive a significant number of reports of engine failure in vehicles outside the scope of 25V-274.  This presents a potential safety risk that warrants further investigation.  ODI is opening this Engineering Analysis (EA) to further evaluate the scope and severity of the potential problem and to fully assess the potential safety-related issues of vehicles built outside the recall scope. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.

Engine

The Office of Defects Investigation (ODI) has received 1,157 reports of engine bearing failure failures in the L87 6.2L engine produced by General Motors (GM). Of the 1,157 reports received, 173 are outside of the scope of recall 25V-274. These engines are installed in Model Years (MY) 2019–2024 Chevrolet Silverado 1500 and GMC Sierra 1500, and 2021-2024MY Chevrolet Suburban and Tahoe, GMC Yukon/Yukon XL, and Cadillac Escalade/Escalade ESV vehicles. The subject engine failures were investigated as part of a Preliminary Evaluation (PE25001).  GM determined that these engine failures were due to multiple supplier manufacturing and quality issues. GM issued recall 25V-274 to address the supplier manufacturing and quality issues produced between March 1, 2021, and May 31, 2024. Based on the issuance of recall 25V-274, NHTSA has closed PE25001. ODI continues to receive a significant number of reports of engine failure in vehicles outside the scope of 25V-274.  This presents a potential safety risk that warrants further investigation.  ODI is opening this Engineering Analysis (EA) to further evaluate the scope and severity of the potential problem and to fully assess the potential safety-related issues of vehicles built outside the recall scope. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.

Engine And Engine Cooling:engine:hard Parts Internal/mechanical

On January 16, 2025, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE25001 after receiving complaints and field reports concerning engine failures in MY2019-2024 GM’s full-size truck and SUV T1XX platform equipped with the L87 6.2L V8 engine. These complainants alleged engine bearing failures resulting in knocking and growling noises from the engine’s bottom end and in some cases more severe consequences such as broken connecting rods leading to engine damage, or engine failure. If the engine fails during vehicle operation, the vehicle will lose propulsion, increasing the risk of a crash. On April 24, 2025, GM issued recall 25V-274 to address the concern with L87 engines produced between March 1, 2021, and May 31, 2024.  GM cited the root cause as a supplier manufacturing and quality issues. GM’s  recall remedy will be either an oil change to an oil with a different viscosity or engine replacement depending on the results of the remedy inspection procedure. To date, ODI has received 1,157 allegations of engine bearing failure. GM submitted 55,464 reports in total, with 29,752 unique VINs. ODI continues to receive allegations of L87 engine failures which fall outside of the scope of recall 25V-274. Based on GM’s recall, ODI will close this PE. NHTSA will continue to investigate complaints of engine failure outside the scope of recall 25V-274 as part ofEngineering Analysis (EA25007). To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.

Engine

On January 16, 2025, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE25001 after receiving complaints and field reports concerning engine failures in MY2019-2024 GM’s full-size truck and SUV T1XX platform equipped with the L87 6.2L V8 engine. These complainants alleged engine bearing failures resulting in knocking and growling noises from the engine’s bottom end and in some cases more severe consequences such as broken connecting rods leading to engine damage, or engine failure. If the engine fails during vehicle operation, the vehicle will lose propulsion, increasing the risk of a crash. On April 24, 2025, GM issued recall 25V-274 to address the concern with L87 engines produced between March 1, 2021, and May 31, 2024.  GM cited the root cause as a supplier manufacturing and quality issues. GM’s  recall remedy will be either an oil change to an oil with a different viscosity or engine replacement depending on the results of the remedy inspection procedure. To date, ODI has received 1,157 allegations of engine bearing failure. GM submitted 55,464 reports in total, with 29,752 unique VINs. ODI continues to receive allegations of L87 engine failures which fall outside of the scope of recall 25V-274. Based on GM’s recall, ODI will close this PE. NHTSA will continue to investigate complaints of engine failure outside the scope of recall 25V-274 as part ofEngineering Analysis (EA25007). To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.

Air Bags:frontal:driver Side:inflator Module

On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.

Air Bags:frontal

On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.

Air Bags

On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.

Air Bags:srs Malfunction Warning Lamp/light

On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.