IllustrationLifter failure of the right bank in 2021 at 19,000 miles. At the time of failure engine was 2.5 quarts low on oil. Ever since, this truck has been using oil excessively. I am currently involved with an oil consumption test. Of which over the last 5k miles I have had to have more oil added by the dealership.
2021 Chevrolet Silverado 1500
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2021 Chevrolet Silverado 1500 do not stand out strongly from the model-year median of 525.
About this comparison →How this year compares
Owner complaints by model year
Compare all Silverado 1500 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
Limited mileage data: 173 of 817 reports include usable mileage. There isn’t enough coverage to show a useful chart.
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Engine. Review the 372 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Power Train. Review the 233 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 111 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
20 crash reports11 fire reports12 injury reports
Power Train complaints
233 reportsMy lifters gave out on a brand new engine with 4000 miles on it. Truck was currently at 60,000 miles on odometer. I was traveling 75mph when everything locked up and all my lights on my dash board lit up. Causing multiple cars to swerve around as I guided the limping truck off the highway.
Fuel regulator- high/low pressure failed. Yes the vehicle is available for inspection (currently at Rotolo Chevrolet). My safety and others were compromised because was on freeway approximately 75 mph and my power and speed was unexpectedly reduced. Almost caused pile up, I had to take evasive measures to guide truck to slow la…
Read full complaint
Fuel regulator- high/low pressure failed. Yes the vehicle is available for inspection (currently at Rotolo Chevrolet). My safety and others were compromised because was on freeway approximately 75 mph and my power and speed was unexpectedly reduced. Almost caused pile up, I had to take evasive measures to guide truck to slow lane, and off the road. Yes, the problem has been confirmed [XXX] by certified Chevrolet technicians at Rotolo Chevrolet-Fontana California. Yes the part/vehicle has been inspected by Certified Chevrolet technician. A few odd hard engine starts(June/July figured a "cold" start). 2 weeks prior([XXX]) to the on road incident, the check engine light came on while driving, stopped vehicle to refuel- when the truck was restarted the check light was no longer illuminated. Scheduled ASAP service appointment 8/16/24 with Chevrolet, they couldn't take it sooner than 8/19/24 being that my truck is still under power train warranty. Unfortunately they say a faulty Fuel regulator is not covered. Document is initial service request order, I was called by Technician stating the specific (fuel regulator) issue and that my repair cost would be over $1,030.00. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
While driving and slowing at an intersection, my vehicle would not accelerate. Only rev the engine causing my to come to a stop in the middle of an intersection. After getting to the side of the road and trou Le shooting for 5 minutes. The vehicle started driving again like nothing was wrong. I took it in to get checked out and …
Read full complaint
While driving and slowing at an intersection, my vehicle would not accelerate. Only rev the engine causing my to come to a stop in the middle of an intersection. After getting to the side of the road and trou Le shooting for 5 minutes. The vehicle started driving again like nothing was wrong. I took it in to get checked out and tje dealership said my transmission was completely broken. At no time did a warning light come on or it feel like it was shifting hard. I researched and found many similar problems with this transmission.
8 speed trans mission jumps, lurges, hard shifts with and without towing. Transmission overheats. Does not engage when cold
When you drive the truck for at least an hour then you turn it off the entire front like vibrates or shakes . It almost feels like something is still turning in the transmission but everything is turned off. This particular truck has already had the engine replaced at 14,000 miles bc it was faulty. It also has issues with tir…
Read full complaint
When you drive the truck for at least an hour then you turn it off the entire front like vibrates or shakes . It almost feels like something is still turning in the transmission but everything is turned off. This particular truck has already had the engine replaced at 14,000 miles bc it was faulty. It also has issues with tires. The radio and lights also all go off for brief time and then it comes back on. At times the drives side seat belt will lock and it pins you to the seat where you cannot move and you have to remove the seat belt. It is becoming more of an issue. I believe the transmission to be going out. Today, I wasn’t sure if the vibration in the truck was going to stop. So I stopped driving the truck and went and got another vehicle to drive
Heard and felt a loud clunk from underneath truck while driving 70 mph on interstate. Pulled off and next available exit with a hotel and parked truck. Cranked truck to move and it would not move forward or backward except for about a foot. Loud grinding noise. Had to call tow truck to tow us to nearest Chevrolet dealer. Dealer …
Read full complaint
Heard and felt a loud clunk from underneath truck while driving 70 mph on interstate. Pulled off and next available exit with a hotel and parked truck. Cranked truck to move and it would not move forward or backward except for about a foot. Loud grinding noise. Had to call tow truck to tow us to nearest Chevrolet dealer. Dealer service department says transfer case has seized up and must be replaced. Transfer case is currently on backorder and not available from GM. Was given rental car to drive home, which is 10 hours away. Truck has been in shop for 7 days as for this writing and I still do not have an answer about when a transfer case will be available and they can repair my truck. I located transfer case at my local dealer but repair dealer says they have to wait on GM.
While accelerating moderately, the transmission downshifted and momentarily locked up the read axle. This caused the rear of the truck to start sliding out. There was a loud bang, and when I checked my outside mirrors, I saw smoke from the tires. I almost lost control in heavy highway traffic. The entire event lasted about a se…
Read full complaint
While accelerating moderately, the transmission downshifted and momentarily locked up the read axle. This caused the rear of the truck to start sliding out. There was a loud bang, and when I checked my outside mirrors, I saw smoke from the tires. I almost lost control in heavy highway traffic. The entire event lasted about a second or two. I am glad I was not pulling a trailer at this time. I reported this incident to my Chevy dealer and informed them of the existing service bulletin on this exact issue. 21-NA-275. The dealer has not followed up with me on their conclusion or what they will do about this dangerous defect. No warning lamps, messages, or other symptoms before this incident.
Bulletin No.: 21-NA-275 Please refer to the posted bulletin. This known issue is absolutely dangerous and needs to be recalled. My truck will lock up going 50 to 60 mph to a complete stop and there's no warning. Gm needs to get all these vehicles fixed it's going to hurt someone or even worse. There's no warming lamps. I'm ge…
Read full complaint
Bulletin No.: 21-NA-275 Please refer to the posted bulletin. This known issue is absolutely dangerous and needs to be recalled. My truck will lock up going 50 to 60 mph to a complete stop and there's no warning. Gm needs to get all these vehicles fixed it's going to hurt someone or even worse. There's no warming lamps. I'm getting my vehicle into the shop as soon as possible. This issue again is very very dangerous.
The contact owns a 2021 Chevrolet Silverado 1500. The contact stated while driving 20 MPH and depressing the accelerator pedal, the vehicle shuddered, jerked, and hesitated to respond. There was no warning light illuminated. The contact stated that the failure had been recurring increasingly while driving. The vehicle was taken …
Read full complaint
The contact owns a 2021 Chevrolet Silverado 1500. The contact stated while driving 20 MPH and depressing the accelerator pedal, the vehicle shuddered, jerked, and hesitated to respond. There was no warning light illuminated. The contact stated that the failure had been recurring increasingly while driving. The vehicle was taken to an independent mechanic, where the vehicle was test-driven, but was not diagnosed. The mechanic determined that the failure was related to the torque converter. The dealer was not notified of the failure. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure and informed the contact that it was a known failure. The manufacturer referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 120,000.
Official recalls
826V083000 · Power Train:automatic Transmission:control Module:software; Power Train:automatic Transmission:fluid/lubricant:valves/valve Body
Feb 12, 2026
General Motors, LLC is recalling certain 2020 Chevrolet Silverado 2500, 3500, GMC Sierra 2500, 3500, and 2020-2022 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles that may have been repaired incorrectly under recall 24V797. The transmission control valve may fail and cause the rear wheels to lock up.
Consequence & remedy
Consequence: Rear wheel lock up increases the risk of a crash.
Remedy: Dealers will inspect the vehicles and update the transmission control software, free of charge. Owner notification letters were mailed March 6, 2026. Owners may contact GMC customer service at 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N252516560. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on February 12, 2026.
Additional source detail variants (2)
Power Train:automatic Transmission:fluid/lubricant:valves/valve Body
General Motors, LLC is recalling certain 2020 Chevrolet Silverado 2500, 3500, GMC Sierra 2500, 3500, and 2020-2022 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles that may have been repaired incorrectly under recall 24V797. The transmission control valve may fail and cause the rear wheels to lock up.
Consequence: Rear wheel lock up increases the risk of a crash.
Remedy: Dealers will inspect the vehicles and update the transmission control software, free of charge. Owner notification letters were mailed March 6, 2026. Owners may contact GMC customer service at 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N252516560. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on February 12, 2026.
Power Train:automatic Transmission:control Module:software
General Motors, LLC is recalling certain 2020 Chevrolet Silverado 2500, 3500, GMC Sierra 2500, 3500, and 2020-2022 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles that may have been repaired incorrectly under recall 24V797. The transmission control valve may fail and cause the rear wheels to lock up.
Consequence: Rear wheel lock up increases the risk of a crash.
Remedy: Dealers will inspect the vehicles and update the transmission control software, free of charge. Owner notification letters were mailed March 6, 2026. Owners may contact GMC customer service at 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N252516560. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on February 12, 2026.
25V274000 · Engine And Engine Cooling:engine:hard Parts Internal/mechanical
Apr 24, 2025
General Motors LLC (GM) is recalling certain 2021-2024 Cadillac Escalade and Escalade ESV, Chevrolet Silverado 1500, Suburban, and Tahoe, GMC Sierra 1500, Yukon, and Yukon XL vehicles equipped with a 6.2L V8 gas engine. The connecting rod and/or crankshaft engine components may have manufacturing defects that can lead to engine damage and engine failure.
Consequence & remedy
Consequence: Engine failure increases the risk of a crash.
Remedy: Dealers will inspect the engine, and as necessary, repair or replace the engine. For vehicles that pass inspection, dealers will add higher viscosity oil, install 6 oil fill cap, replace the oil filter, and update the owner's manual. Repairs will be performed free of charge. Owner notification letters were mailed June 18, 2025. Owners may contact Cadillac customer service at 1-800-333-4223, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is N252494000.
24V797000 · Power Train:automatic Transmission:control Module:software; Power Train:automatic Transmission:fluid/lubricant:valves/valve Body
Oct 24, 2024
General Motors, LLC (GM) is recalling certain 2020-2022 Chevrolet Silverado 1500, 2500, 3500, GMC Sierra 1500, 2500, 3500, 2021 Cadillac Escalade, Escalade ESV, Chevrolet Tahoe, Suburban, GMC Yukon, and Yukon XL vehicles equipped with diesel engines. The transmission control valve may fail and cause the rear wheels to lock-up.
Consequence & remedy
Consequence: Rear wheel lock-up can increase the risk of a crash.
Remedy: Dealers will install new transmission control module software, free of charge. GM will provide a special coverage program to cover the repair of transmissions that are identified by the remedy software as containing a defective control valve. Owner notification letters were mailed December 12, 2024. Owners may contact GM customer service at 1-888-988-7267, Cadillac customer service at 1-800-458-8006, GMC customer service at GMC 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N242454440.
Additional source detail variants (2)
Power Train:automatic Transmission:fluid/lubricant:valves/valve Body
General Motors, LLC (GM) is recalling certain 2020-2022 Chevrolet Silverado 1500, 2500, 3500, GMC Sierra 1500, 2500, 3500, 2021 Cadillac Escalade, Escalade ESV, Chevrolet Tahoe, Suburban, GMC Yukon, and Yukon XL vehicles equipped with diesel engines. The transmission control valve may fail and cause the rear wheels to lock-up.
Consequence: Rear wheel lock-up can increase the risk of a crash.
Remedy: Dealers will install new transmission control module software, free of charge. GM will provide a special coverage program to cover the repair of transmissions that are identified by the remedy software as containing a defective control valve. Owner notification letters were mailed December 12, 2024. Owners may contact GM customer service at 1-888-988-7267, Cadillac customer service at 1-800-458-8006, GMC customer service at GMC 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N242454440.
Power Train:automatic Transmission:control Module:software
General Motors, LLC (GM) is recalling certain 2020-2022 Chevrolet Silverado 1500, 2500, 3500, GMC Sierra 1500, 2500, 3500, 2021 Cadillac Escalade, Escalade ESV, Chevrolet Tahoe, Suburban, GMC Yukon, and Yukon XL vehicles equipped with diesel engines. The transmission control valve may fail and cause the rear wheels to lock-up.
Consequence: Rear wheel lock-up can increase the risk of a crash.
Remedy: Dealers will install new transmission control module software, free of charge. GM will provide a special coverage program to cover the repair of transmissions that are identified by the remedy software as containing a defective control valve. Owner notification letters were mailed December 12, 2024. Owners may contact GM customer service at 1-888-988-7267, Cadillac customer service at 1-800-458-8006, GMC customer service at GMC 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N242454440.
21V985000 · Tires:temporary/emergency Spare Tire
Dec 16, 2021
General Motors (GM) is recalling certain 2019-2021 GMC Sierra 1500 and Silverado 1500 vehicles equipped with certain accessory road tires and a 17" spare tire. The 17" spare tire provided with the vehicle is not compatible for use with the accessory wheels, which can cause the anti-lock brake system (ABS) to not function properly under certain conditions.
Consequence & remedy
Consequence: An ABS system that does not function properly can increase the risk of a crash.
Remedy: Dealers will provide a new 17" spare tire and wheel assembly that is compatible with the accessory wheels, free of charge. Dealers will also apply a new spare tire information label, and provide owners with an owner's manual insert clarifying which spare tire to use with the accessory road tires and with the 17" original tires. Owner notification letters were mailed February 7, 2022. Owners may contact GM customer service at 1-800-462-8782 or GMC customer service at 1-800-462-8782. GM's number for this recall is N212346510.
21V495000 · Air Bags:frontal
Jul 1, 2021
General Motors, LLC. (GM) is recalling certain 2021 Chevrolet Silverado 1500 vehicles. The front driver's side air bag module may be missing one or more metal tabs that secure the plastic air bag cover to the housing.
Consequence & remedy
Consequence: The missing tabs may prevent the air bag from deploying properly, increasing the risk of injury in a crash.
Remedy: Dealers will inspect the driver frontal air bag, and replace it if necessary, free of charge. Owner notification letters are expected to be mailed August 16, 2021. Owners may contact Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N212336560.
20V811000 · Seat Belts; Seat Belts:critical Fasteners
Dec 23, 2020
General Motors, LLC (GM) is recalling certain 2020 Chevrolet Bolt EV and 2021 GMC Canyon and Sierra 1500, 2500 and 3500, Yukon, Yukon XL, Cadillac Escalade and Escalade ESV and Chevrolet Blazer, Camaro, Colorado, Equinox, Silverado 1500, 2500 and 3500, Suburban and Tahoe vehicles. Incorrect bolts may have been used at one or more fastening locations to secure the seat belts to the vehicle. If an incorrect bolt was used, the seat belt may not be properly attached to the vehicle.
Consequence & remedy
Consequence: If a seat belt assembly is not properly attached to the vehicle, the seat belt may not properly restrain an occupant in the event of a crash, increasing the risk of injury.
Remedy: GM will notify owners, and dealers will replace the suspect bolts, free of charge. The recall began January 29, 2021. Owners may contact GMC customer service at 1-800-462-8785, Cadillac customer service at 1-800-458-8006, or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202322230.
Additional source detail variants (2)
Seat Belts:critical Fasteners
General Motors, LLC (GM) is recalling certain 2020 Chevrolet Bolt EV and 2021 GMC Canyon and Sierra 1500, 2500 and 3500, Yukon, Yukon XL, Cadillac Escalade and Escalade ESV and Chevrolet Blazer, Camaro, Colorado, Equinox, Silverado 1500, 2500 and 3500, Suburban and Tahoe vehicles. Incorrect bolts may have been used at one or more fastening locations to secure the seat belts to the vehicle. If an incorrect bolt was used, the seat belt may not be properly attached to the vehicle.
Consequence: If a seat belt assembly is not properly attached to the vehicle, the seat belt may not properly restrain an occupant in the event of a crash, increasing the risk of injury.
Remedy: GM will notify owners, and dealers will replace the suspect bolts, free of charge. The recall began January 29, 2021. Owners may contact GMC customer service at 1-800-462-8785, Cadillac customer service at 1-800-458-8006, or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202322230.
Seat Belts
General Motors, LLC (GM) is recalling certain 2020 Chevrolet Bolt EV and 2021 GMC Canyon and Sierra 1500, 2500 and 3500, Yukon, Yukon XL, Cadillac Escalade and Escalade ESV and Chevrolet Blazer, Camaro, Colorado, Equinox, Silverado 1500, 2500 and 3500, Suburban and Tahoe vehicles. Incorrect bolts may have been used at one or more fastening locations to secure the seat belts to the vehicle. If an incorrect bolt was used, the seat belt may not be properly attached to the vehicle.
Consequence: If a seat belt assembly is not properly attached to the vehicle, the seat belt may not properly restrain an occupant in the event of a crash, increasing the risk of injury.
Remedy: GM will notify owners, and dealers will replace the suspect bolts, free of charge. The recall began January 29, 2021. Owners may contact GMC customer service at 1-800-462-8785, Cadillac customer service at 1-800-458-8006, or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202322230.
20V792000 · Seat Belts; Seat Belts:critical Fasteners
Dec 17, 2020
General Motors, LLC (GM) is recalling certain 2019-2021 Chevrolet Silverado 1500 and GMC Sierra 1500, 2021 Chevrolet Suburban and Tahoe and GMC Yukon XL and 2020-2021 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles. The seat belt brackets may not be secured to the seat frame in the front-row center seating position.
Consequence & remedy
Consequence: If a seat-belt bracket is not secured, the seat belt may not properly restrain an occupant in the front-row center seat position, increasing the risk of injury in a crash.
Remedy: GM will notify owners, and dealers will inspect left-side and right-side front-row center seat-belt bracket attachments and reassemble it correctly as necessary, free of charge. The recall began January 26, 2021. Owners may contact GMC customer service at 1-800-462-8782, Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202314670.
Additional source detail variants (2)
Seat Belts:critical Fasteners
General Motors, LLC (GM) is recalling certain 2019-2021 Chevrolet Silverado 1500 and GMC Sierra 1500, 2021 Chevrolet Suburban and Tahoe and GMC Yukon XL and 2020-2021 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles. The seat belt brackets may not be secured to the seat frame in the front-row center seating position.
Consequence: If a seat-belt bracket is not secured, the seat belt may not properly restrain an occupant in the front-row center seat position, increasing the risk of injury in a crash.
Remedy: GM will notify owners, and dealers will inspect left-side and right-side front-row center seat-belt bracket attachments and reassemble it correctly as necessary, free of charge. The recall began January 26, 2021. Owners may contact GMC customer service at 1-800-462-8782, Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202314670.
Seat Belts
General Motors, LLC (GM) is recalling certain 2019-2021 Chevrolet Silverado 1500 and GMC Sierra 1500, 2021 Chevrolet Suburban and Tahoe and GMC Yukon XL and 2020-2021 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles. The seat belt brackets may not be secured to the seat frame in the front-row center seating position.
Consequence: If a seat-belt bracket is not secured, the seat belt may not properly restrain an occupant in the front-row center seat position, increasing the risk of injury in a crash.
Remedy: GM will notify owners, and dealers will inspect left-side and right-side front-row center seat-belt bracket attachments and reassemble it correctly as necessary, free of charge. The recall began January 26, 2021. Owners may contact GMC customer service at 1-800-462-8782, Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202314670.
20V684000 · Tires
Nov 5, 2020
General Motors LLC (GM) is recalling certain 2020 Buick Enclave, Cadillac XT5, GMC Acadia and Chevrolet Traverse vehicles and 2020-2021 Chevrolet Silverado 1500, GMC Sierra 1500 vehicles. The vehicles may have been manufactured with Continental tires that were overcured.
Consequence & remedy
Consequence: Overcured tires may experience a carcass break in the sidewall resulting in a sudden air loss or could develop a belt edge separation which could lead to partial or full tread/belt loss. Either condition increases the risk of a crash.
Remedy: GM will notify owners, and dealers will inspect vehicles and replace tires that have DOT number and production mold number combinations identified by Continental, free of charge. The recall began December 17, 2020. Owners may contact GMC customer service at 1-888-988-7267, Buick customer service at 1-866-608-8080, Chevrolet customer service at 1-800-222-1020 or Cadillac customer service at 1-800-458-8006. GM's number for this recall is N202319030.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
5EA26005 · Loss Of Motive Power Due To Engine Failure Post Recall Remedy
Opened Aug 20, 2026 · No close date supplied
Status: open (inferred from source dates) · Engine
On January 16, 2026, the Office of Defects Investigation (ODI) opened Recall Query RQ26001. This investigation was opened to assess the remedy effectiveness of Recall 25V-274. ODI has received complaints alleging engine failure in vehicles after the recall remedy had been completed, whether that remedy involved an oil viscosity change or a complete engine replacement. General Motors (GM) issued Recall 25V-274 to address concerns of engine failure in the L87 engines produced between March 1, 2021 and May 31, 2024. GM cited the root cause as a supplier manufacturing and quality issue. GM’s recall remedy for Recall 25V-274 consisted of two different repairs, either an oil viscosity change or an engine replacement, based on the results of the remedy inspection procedure. ODI continues to receive reports of engine failures after the completion of the recall remedy. To date, ODI has received 499 complaints alleging post-remedy engine failure in vehicles subject to Recall 25V-274, 473 of which involved an oil viscosity change and 26 a complete engine replacement. Additionally, ODI has received 191 reports of L87 engine failures in engines produced after the production period cited in Recall 25V-274. GM reported receiving 6,953 complaints of post-remedy engine failure. ODI is opening this Engineering Analysisto continue investigating complaints of post-remedy engine failure. ODI is expanding the scope of this Investigation to include engines produced after the production period cited in the recall. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
RQ26001 · Loss Of Motive Power Due To Engine Failure Post Recall Remedy
Opened Jan 16, 2026 · Closed Aug 20, 2026
Status: closed (inferred from source dates) · Engine
On January 16, 2026, the Office of Defects Investigation (ODI) opened Recall Query RQ26001. This investigation was opened to assess the remedy effectiveness of Recall 25V-274. ODI has received complaints alleging engine failure in vehicles after the recall remedy had been completed, whether that remedy involved an oil viscosity change or a complete engine replacement. General Motors (GM) issued Recall 25V-274 to address concerns of engine failure in the L87 engines produced between March 1, 2021 and May 31, 2024. GM cited the root cause as a supplier manufacturing and quality issue. GM’s recall remedy for Recall 25V-274 consisted of two different repairs, either an oil viscosity change or an engine replacement, based on the results of the remedy inspection procedure. ODI continues to receive reports of engine failures after the completion of the recall remedy. To date, ODI has received 499 complaints alleging post-remedy engine failure in vehicles subject to Recall 25V-274, 473 of which involved an oil viscosity change and 26 a complete engine replacement. GM reported receiving 6,953 complaints of post-remedy engine failure. ODI will close this RQ and continue to investigate complaints of post-remedy engine failure for Recall 25V-274 as part of an Engineering Analysis (EA26005). To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
EA25007 · Loss Of Motive Power Due To Engine Failure
Opened Oct 23, 2025 · No close date supplied
Status: open (inferred from source dates) · Engine; Engine And Engine Cooling:engine:hard Parts Internal/mechanical
The Office of Defects Investigation (ODI) has received 1,157 reports of engine bearing failure failures in the L87 6.2L engine produced by General Motors (GM). Of the 1,157 reports received, 173 are outside of the scope of recall 25V-274. These engines are installed in Model Years (MY) 2019–2024 Chevrolet Silverado 1500 and GMC Sierra 1500, and 2021-2024MY Chevrolet Suburban and Tahoe, GMC Yukon/Yukon XL, and Cadillac Escalade/Escalade ESV vehicles. The subject engine failures were investigated as part of a Preliminary Evaluation (PE25001). GM determined that these engine failures were due to multiple supplier manufacturing and quality issues. GM issued recall 25V-274 to address the supplier manufacturing and quality issues produced between March 1, 2021, and May 31, 2024. Based on the issuance of recall 25V-274, NHTSA has closed PE25001. ODI continues to receive a significant number of reports of engine failure in vehicles outside the scope of 25V-274. This presents a potential safety risk that warrants further investigation. ODI is opening this Engineering Analysis (EA) to further evaluate the scope and severity of the potential problem and to fully assess the potential safety-related issues of vehicles built outside the recall scope. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Engine And Engine Cooling:engine:hard Parts Internal/mechanical
The Office of Defects Investigation (ODI) has received 1,157 reports of engine bearing failure failures in the L87 6.2L engine produced by General Motors (GM). Of the 1,157 reports received, 173 are outside of the scope of recall 25V-274. These engines are installed in Model Years (MY) 2019–2024 Chevrolet Silverado 1500 and GMC Sierra 1500, and 2021-2024MY Chevrolet Suburban and Tahoe, GMC Yukon/Yukon XL, and Cadillac Escalade/Escalade ESV vehicles. The subject engine failures were investigated as part of a Preliminary Evaluation (PE25001). GM determined that these engine failures were due to multiple supplier manufacturing and quality issues. GM issued recall 25V-274 to address the supplier manufacturing and quality issues produced between March 1, 2021, and May 31, 2024. Based on the issuance of recall 25V-274, NHTSA has closed PE25001. ODI continues to receive a significant number of reports of engine failure in vehicles outside the scope of 25V-274. This presents a potential safety risk that warrants further investigation. ODI is opening this Engineering Analysis (EA) to further evaluate the scope and severity of the potential problem and to fully assess the potential safety-related issues of vehicles built outside the recall scope. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
Engine
The Office of Defects Investigation (ODI) has received 1,157 reports of engine bearing failure failures in the L87 6.2L engine produced by General Motors (GM). Of the 1,157 reports received, 173 are outside of the scope of recall 25V-274. These engines are installed in Model Years (MY) 2019–2024 Chevrolet Silverado 1500 and GMC Sierra 1500, and 2021-2024MY Chevrolet Suburban and Tahoe, GMC Yukon/Yukon XL, and Cadillac Escalade/Escalade ESV vehicles. The subject engine failures were investigated as part of a Preliminary Evaluation (PE25001). GM determined that these engine failures were due to multiple supplier manufacturing and quality issues. GM issued recall 25V-274 to address the supplier manufacturing and quality issues produced between March 1, 2021, and May 31, 2024. Based on the issuance of recall 25V-274, NHTSA has closed PE25001. ODI continues to receive a significant number of reports of engine failure in vehicles outside the scope of 25V-274. This presents a potential safety risk that warrants further investigation. ODI is opening this Engineering Analysis (EA) to further evaluate the scope and severity of the potential problem and to fully assess the potential safety-related issues of vehicles built outside the recall scope. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
PE25001 · Loss Of Motive Power Due To Engine Failure
Opened Jan 16, 2025 · Closed Oct 23, 2025
Status: closed (inferred from source dates) · Engine; Engine And Engine Cooling:engine:hard Parts Internal/mechanical
On January 16, 2025, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE25001 after receiving complaints and field reports concerning engine failures in MY2019-2024 GM’s full-size truck and SUV T1XX platform equipped with the L87 6.2L V8 engine. These complainants alleged engine bearing failures resulting in knocking and growling noises from the engine’s bottom end and in some cases more severe consequences such as broken connecting rods leading to engine damage, or engine failure. If the engine fails during vehicle operation, the vehicle will lose propulsion, increasing the risk of a crash. On April 24, 2025, GM issued recall 25V-274 to address the concern with L87 engines produced between March 1, 2021, and May 31, 2024. GM cited the root cause as a supplier manufacturing and quality issues. GM’s recall remedy will be either an oil change to an oil with a different viscosity or engine replacement depending on the results of the remedy inspection procedure. To date, ODI has received 1,157 allegations of engine bearing failure. GM submitted 55,464 reports in total, with 29,752 unique VINs. ODI continues to receive allegations of L87 engine failures which fall outside of the scope of recall 25V-274. Based on GM’s recall, ODI will close this PE. NHTSA will continue to investigate complaints of engine failure outside the scope of recall 25V-274 as part ofEngineering Analysis (EA25007). To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Engine And Engine Cooling:engine:hard Parts Internal/mechanical
On January 16, 2025, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE25001 after receiving complaints and field reports concerning engine failures in MY2019-2024 GM’s full-size truck and SUV T1XX platform equipped with the L87 6.2L V8 engine. These complainants alleged engine bearing failures resulting in knocking and growling noises from the engine’s bottom end and in some cases more severe consequences such as broken connecting rods leading to engine damage, or engine failure. If the engine fails during vehicle operation, the vehicle will lose propulsion, increasing the risk of a crash. On April 24, 2025, GM issued recall 25V-274 to address the concern with L87 engines produced between March 1, 2021, and May 31, 2024. GM cited the root cause as a supplier manufacturing and quality issues. GM’s recall remedy will be either an oil change to an oil with a different viscosity or engine replacement depending on the results of the remedy inspection procedure. To date, ODI has received 1,157 allegations of engine bearing failure. GM submitted 55,464 reports in total, with 29,752 unique VINs. ODI continues to receive allegations of L87 engine failures which fall outside of the scope of recall 25V-274. Based on GM’s recall, ODI will close this PE. NHTSA will continue to investigate complaints of engine failure outside the scope of recall 25V-274 as part ofEngineering Analysis (EA25007). To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Engine
On January 16, 2025, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE25001 after receiving complaints and field reports concerning engine failures in MY2019-2024 GM’s full-size truck and SUV T1XX platform equipped with the L87 6.2L V8 engine. These complainants alleged engine bearing failures resulting in knocking and growling noises from the engine’s bottom end and in some cases more severe consequences such as broken connecting rods leading to engine damage, or engine failure. If the engine fails during vehicle operation, the vehicle will lose propulsion, increasing the risk of a crash. On April 24, 2025, GM issued recall 25V-274 to address the concern with L87 engines produced between March 1, 2021, and May 31, 2024. GM cited the root cause as a supplier manufacturing and quality issues. GM’s recall remedy will be either an oil change to an oil with a different viscosity or engine replacement depending on the results of the remedy inspection procedure. To date, ODI has received 1,157 allegations of engine bearing failure. GM submitted 55,464 reports in total, with 29,752 unique VINs. ODI continues to receive allegations of L87 engine failures which fall outside of the scope of recall 25V-274. Based on GM’s recall, ODI will close this PE. NHTSA will continue to investigate complaints of engine failure outside the scope of recall 25V-274 as part ofEngineering Analysis (EA25007). To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE21010 · Air Bag Malfunction
Opened Apr 9, 2021 · Closed Aug 24, 2023
Status: closed (inferred from source dates) · Air Bags; Air Bags:frontal; Air Bags:frontal:driver Side:inflator Module; Air Bags:srs Malfunction Warning Lamp/light
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.
Additional source detail variants (4)
Air Bags:frontal:driver Side:inflator Module
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.
Air Bags:frontal
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.
Air Bags
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.
Air Bags:srs Malfunction Warning Lamp/light
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.