← New search

2015 Chevrolet Silverado 1500

Owner reports · Recalls · Investigations

More warning signs than most Silverado 1500 years

Owner complaints for the 2015 Chevrolet Silverado 1500 are substantially higher than the model-year median of 525.

About this comparison →

When problems were reported

Mileage at the reported incident

678 reports with mileage · 426 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Service Brakes. Review the 350 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Electrical System. Review the 163 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Steering. Review the 160 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

58 crash reports14 fire reports24 injury reports

Steering complaints

160 reports
Clear category filter
51,000 miles · Apr 3, 2019
Electrical SystemEngineSteering

WHILE DRIVING SLOW AND MAKING A HARD LEFT TURN EVERYTHING FLASHES OFF 0N DASH ,THEN ON, ON DASH,BUT ENGINE SHUTS OFF CAUSING STEERING AND BRAKING SAFETY CONCERNS,THIS HAS HAPPENED THREE TIMES IN LAST TWO WEEK TOOK IT TO DEALERSHIP THEY COULDN'T

NHTSA ODI #11193734

Mileage unknown · Mar 2, 2019
Steering

THE RACK AND PINION HAS GONE OUT ON MY 2015 CHEVY 1500. LOUD CREAKING NOISES CAN BE HEARD FROM TURNING THE WHEEL SIDE TO SIDE. FOR A TRUCK TO BE 4 YEARS AND WITH 40K MILES AND THIS TO GO BAD IS A REAL QUALITY ISSUE. ONLINE I HAVE FOUND NUMEROUS REPORTS OF THIS ISSUE

NHTSA ODI #11183596

26,710 miles · Feb 19, 2019
Steering

I WAS DRIVING SLOWED DOWN TO TURN RIGHT ONTO MY STREET IOSS TOTAL CONTROL OF MY TRUCK ENDED UP ON THE SIDE WALK ON THE OPPOSITE SIDE OF ROAD AS I WAS NOT ABLE TO CONTROL MY TRUCK, MY TRUCK SHUT DOWN COMPLETELY WHILE IN DRIVE, MYDASHBOARD STARTED TO DISPLAY STABILITRACK DISABLED, STEERING ASSISTANT REDUCED, TWO KEY PROGRAMMED, OP…

Read full complaint

I WAS DRIVING SLOWED DOWN TO TURN RIGHT ONTO MY STREET IOSS TOTAL CONTROL OF MY TRUCK ENDED UP ON THE SIDE WALK ON THE OPPOSITE SIDE OF ROAD AS I WAS NOT ABLE TO CONTROL MY TRUCK, MY TRUCK SHUT DOWN COMPLETELY WHILE IN DRIVE, MYDASHBOARD STARTED TO DISPLAY STABILITRACK DISABLED, STEERING ASSISTANT REDUCED, TWO KEY PROGRAMMED, OPEN AND CLOSE DRIVER DOOR. THIS IS NOT THE FIRST TIME THIS HAS HAPPENED BUT THE FIRST TIME TO THIS EXTREME THAT IS WHY WE HAD TOOK OUR TRUCK TO VANDERGRIFF CHEVROLET IN ARLINGTON TX ON 2/16/19 WERE THEY TOOK CARE OF THE OPEN RECALL AND DID A SOFTWARE RESET FOR LOSS OF STEERING ASSIST C18289 AND POWER STEERING CONTROL MODULE BUT EVEN AFTER SOFTWARE RESET I'M STILL HAVING THE SAME ISSUE I'M TAKING MY VEHICLE IN AGAIN TO BE SERVICED AS I FIND THIS LOSS OF STEERING VERY DANGEROUS THANKFULLY NO ONE WAS ON THAT SIDE WALK THAT COULD'VE BEEN SERIOUSLY HURT. THE OTHER TWO TIMES THIS HAPPENED PRIOR TO YESTERDAY WAS WHEN WE WERE IN A DRIVE THRU AND WE WERE TURNING TO ORDER FOOD AND ONCE TURNING INTO MY SONS SCHOOL AGAIN VEHICLE SHUT DOWN COMPLETELY WHILE IN DRIVE ALL THE WARNINGS LIGHTS DISPLAYING.

NHTSA ODI #11181017

51,321 miles · Feb 12, 2019
Service BrakesSteering

WHEN SLOWING DOWN TO PARK, I LOST BRAKING AND COULD NOT STOP THE TRUCK. I HAD TO PUT THE TRUCK IN PARK TO STOP THE MOMENTUM. THIS HAPPENED GOING IN REVERSE. WHEN TAKEN TO DEALER I WAS CHARGED $470.96 FOR PARTS AND LABOR AT N THE VACUUM PUMP WHICH PROVIDES POWER FOR BRAKING AND STEERING.

NHTSA ODI #11176457

49,000 miles · Jan 29, 2019
Service BrakesSteeringUnknown Or Other

AS MY WIFE CAME TO A COMPLETE STOP AT A STOPLIGHT AND AS THE LIGHT TURNED GREEN, SHE PRESSED THE GAS PEDAL AND THE TRUCK WOULD NOT ACCERLATE. SHE PRESSED THE GAS PEDAL DOWN TO THE FLOOR BOARD AND STILL WOULD NOT ACCERLATE. SO DUE TO THIS THE TRUCK SLOWLY ROLLED FOWARD. SHE SLAMMED ON THE BRAKES AND THE BRAKES WOULD NOT MOVE. LIK…

Read full complaint

AS MY WIFE CAME TO A COMPLETE STOP AT A STOPLIGHT AND AS THE LIGHT TURNED GREEN, SHE PRESSED THE GAS PEDAL AND THE TRUCK WOULD NOT ACCERLATE. SHE PRESSED THE GAS PEDAL DOWN TO THE FLOOR BOARD AND STILL WOULD NOT ACCERLATE. SO DUE TO THIS THE TRUCK SLOWLY ROLLED FOWARD. SHE SLAMMED ON THE BRAKES AND THE BRAKES WOULD NOT MOVE. LIKE IF THEY BECAME LOCKED AND WOULDN'T MOVE AN INCH. AT THIS POINT SHE IS TRYING TO GET OFF THE ROAD TO THE SHOULDER, TO AVOID ONCOMING TRAFFIC. THEN SHE FINDS THAT THE STEERING WHEEL IS ALSO LOCKED AND CAN NOT BE TURNED. IT'S TAKING HER MAXIMUM EFFORT TO STOP THE TRUCK FROM ROLLING FORWARD AND TO VEER OFF THE ROAD TO AVOID OTHER VEHICLES. SHE IS FINALLY ABLE TO STOP THE VEHICLE AFTER ABOUT 100 YARDS OF EFFORT AND WAITS ABOUT 10 MINUTES, BEFORE THE BRAKES AND STEERING WHEEL WOULD FREE UP. NO ERROR MESSAGE WAS PRESENT THE ENTIRE TIME THESE FUNCTIONS WERE DISABLED AND AFTER THEY FREED UP, IT WAS LIKE IF NOTHING EVER HAPPENED. NO CHECK ENGINE LIGHT HAS EVER BEEN ON THIS VEHICLE. STRONG BELIEF THIS IS A MANUFACTURING DEFECT AND SHOULD HAVE A RECALL.

NHTSA ODI #11172985

Mileage unknown · Jan 28, 2019
Steering

TL* THE CONTACT OWNS A 2015 CHEVROLET SILVERADO 1500. AFTER THE VEHICLE WAS REPAIRED PER NHTSA CAMPAIGN NUMBER: 18V586000 (STEERING), THE VEHICLE STALLED AND THE INSTRUMENT PANEL LIGHTING FLICKERED. THE VEHICLE WAS ABLE TO RESTART; HOWEVER, IT STALLED AGAIN. THE VEHICLE WAS ABLE TO OPERATE NORMALLY AFTER BEING RESTARTED. THE VEH…

Read full complaint

TL* THE CONTACT OWNS A 2015 CHEVROLET SILVERADO 1500. AFTER THE VEHICLE WAS REPAIRED PER NHTSA CAMPAIGN NUMBER: 18V586000 (STEERING), THE VEHICLE STALLED AND THE INSTRUMENT PANEL LIGHTING FLICKERED. THE VEHICLE WAS ABLE TO RESTART; HOWEVER, IT STALLED AGAIN. THE VEHICLE WAS ABLE TO OPERATE NORMALLY AFTER BEING RESTARTED. THE VEHICLE WAS TAKEN TO THE ORIGINAL RON CARTER CHEVROLET (3206 FM 528 ROAD, CHEVROLET BUILDING, ALVIN, TX 77511,(281) 819-6007), BUT WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED. THE VIN AND FAILURE MILEAGE WERE UNKNOWN.

NHTSA ODI #11172486

76,877 miles · Jan 4, 2019
Steering

ELECTRIC ASSIST NOT WORKING

NHTSA ODI #11165235

Mileage unknown · Dec 11, 2018
Electronic Stability Control (esc)Service BrakesSteering

2015 CHEVROLET SILVERADO 1500. CONSUMER WRITES IN REGARDS TO POWER STEERING. *LD THE CONSUMER STATED ABS SYSTEM AND STABILITRAK LIGHT ILLUMINATED. THE CONSUMER WAS MADE AWARE OF A RECALL CONCERNING THE STEERING FAILURE AFTER HAVING THE VEHICLE REPAIRED. THE CONSUMER REQUESTED TO BE REIMBURSED FOR THE REPAIRS.*JS

NHTSA ODI #11156289

46,000 miles · Dec 10, 2018
Electrical SystemSteering

I BROUGHT MY VEHICLE TO THE DEALERSHIP THAT I BOUGHT MY VEHICLE FROM AFTER IT SHOWED WHAT I BELIEVED TO BE SIGNS OF THE ELECTRONIC POWER STEERING (EPS) RECALL AFFECTING IT. THE DEALERSHIP APPLIED THE FIX THAT GM HAD AND SENT ME ON MY WAY. THE VERY NEXT DAY I EXPERIENCED WHAT I BELIEVED TO BE THE ELECTRONIC POWER STEERING SYSTEM…

Read full complaint

I BROUGHT MY VEHICLE TO THE DEALERSHIP THAT I BOUGHT MY VEHICLE FROM AFTER IT SHOWED WHAT I BELIEVED TO BE SIGNS OF THE ELECTRONIC POWER STEERING (EPS) RECALL AFFECTING IT. THE DEALERSHIP APPLIED THE FIX THAT GM HAD AND SENT ME ON MY WAY. THE VERY NEXT DAY I EXPERIENCED WHAT I BELIEVED TO BE THE ELECTRONIC POWER STEERING SYSTEM ACTING UP AGAIN. THIS TIME I WAS TRAVELING AT 55 M.P.H. ON THE HIGHWAY BEGINNING THE INTERCHANGE TO ANOTHER HIGHWAY AND COULD NOT TURN THE STEERING WHEEL FOR APPROXIMATELY 2 SECONDS. THE LOSS OF STEERING WAS ALMOST AS SOON AS I STARTED THE TURN AND ALMOST CAUSED ME TO GO OFF OF THE HIGHWAY. THEN FOR THE NEXT 5-7 SECONDS I WAS ABLE TO MANUALLY TURN THE STEERING WHEEL WITHOUT POWER STEERING. ALL OF A SUDDEN THE POWER STEERING TURNED BACK ON AND, BECAUSE OF HOW HARD I WAS TRYING TO TURN THE WHEEL, I ALMOST ENDED UP IN THE LANE TO MY RIGHT WHERE ANOTHER VEHICLE WAS. I HAD NO PRIOR ISSUES LIKE THIS UNTIL THE RECALL WAS WORKED AT THE DEALERSHIP. ALMOST IMMEDIATELY AFTER LEAVING THE DEALERSHIP THE TRUCK WAS ACTING WEIRD, AND AT A STOP THE TRUCK FELT AS IF IT WAS STRUGGLING TO STAY RUNNING. THE DEALERSHIP WAS CONTACTED AND AGREED TO HAVE IT TOWED BACK TO THEM TWO DAYS LATER. NOW THEY ARE TELLING ME IT IS DUE TO BAD BATTERY CABLES AND THAT CAUSED POWER LOSS DURING THE TURN. THEY SPENT HOURS SCANNING THE SYSTEM TO FIND THAT THIS ACTUALLY HAPPENED, WHICH THEY CLAIM THEY COULD NOT FIND, BUT THERE WAS A WARNING LIGHT THAT SHOWED ON THE DASH NOTIFYING ME THAT THE POWER STEERING WAS OUT AND TO DRIVE WITH CARE, SO I DO NOT UNDERSTAND HOW THEY DID NOT FIND IT DURING THEIR SCAN. THEY THEN TELL ME THERE IS A SERVICE BULLETIN, THAT CAME OUT A MONTH AFTER THE EPS RECALL DID, AND IT WILL BE AN OUT OF POCKET EXPENSE. I CANNOT STOP THINKING THAT THIS ISSUE IS A DIRECT RESULT OF THE EPS SOFTWARE FIX AND SHOULD BE INCLUDED TO THE RECALL TO REPLACE THE BATTERY CABLES.

NHTSA ODI #11157255

55,100 miles · Nov 19, 2018
Steering

TL* THE CONTACT OWNS A 2015 CHEVROLET SILVERADO 1500. WHILE DRIVING APPROXIMATELY 15 MPH, THE SERVICE POWER STEERING WARNING MESSAGE ILLUMINATED AND THE VEHICLE LOST POWER STEERING ABILITY. THE VEHICLE WAS DRIVEN TO CIOCCA CHEVROLET OF QUAKERTOWN (855 S WEST END BLVD, QUAKERTOWN, PA 18951) WHERE IT WAS DIAGNOSED THAT THE STEERIN…

Read full complaint

TL* THE CONTACT OWNS A 2015 CHEVROLET SILVERADO 1500. WHILE DRIVING APPROXIMATELY 15 MPH, THE SERVICE POWER STEERING WARNING MESSAGE ILLUMINATED AND THE VEHICLE LOST POWER STEERING ABILITY. THE VEHICLE WAS DRIVEN TO CIOCCA CHEVROLET OF QUAKERTOWN (855 S WEST END BLVD, QUAKERTOWN, PA 18951) WHERE IT WAS DIAGNOSED THAT THE STEERING GEAR ASSEMBLY, TORQUE SENSOR, AND HARNESS NEEDED TO BE REPLACED. THE VEHICLE WAS REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 55,100.

NHTSA ODI #11152479

Official recalls

11

21V504000 · Air Bags:side/window:curtain:inflator

Jul 1, 2021

General Motors LLC (GM) is recalling certain 2015-2016 GMC Sierra 1500, 2500, 3500, and Chevrolet Silverado 1500, 2500, and 3500 trucks. The roof-rail air bag (RRAB) inflator end cap may detach from the inflator, or the inflator sidewall may rupture.

Consequence & remedy

Consequence: A separated inflator end cap or inflator rupture can allow compressed gas to escape, resulting in the end cap or other components being propelled into the vehicle, increasing the risk of injury or crash.

Remedy: Dealers will replace the left and right side RRAB modules, free of charge. Interim owner notification letters informing owners of the safety risk were mailed on August 18, 2021. Owners will receive a second notice when the remedy is available. Phase I owner notification letters were mailed on May 5, 2022. Phase II owner notification letters are expected to be mailed on May 31, 2022. Owners may contact GMC customer service at 1-888-988-7267 or Chevrolet customer service at 1-800-222-1020. This recall supersedes NHTSA recall number 20V-736. GM's number for this recall is N202324251.

21V245000 · Seat Belts:front

Apr 8, 2021

General Motors, LLC (GM) is recalling certain 2014-2016 Chevrolet Silverado 1500, 2015-2016 Chevrolet Tahoe, and 2014-2015 GMC Sierra 1500 vehicles that may have received an incorrect replacement tensioner cable assembly as part of a previous recall remedy or a subsequent repair. The flexible steel cable connecting the driver's seat belt to the outboard side of the seat may be repeatedly bent over the seat side shield as the driver enters and exits the vehicle causing the cable to fatigue and separate.

Consequence & remedy

Consequence: A broken pretensioner cable reduces the effectiveness of the driver's seat belt, increasing the risk of injury.

Remedy: GM will notify owners, and dealers will replace the driver seat belt lap pretensioner, free of charge. The recall began on May 5, 2021. Owners may contact Chevrolet customer service at 1-800-222-1020, and GMC customer service at 1-800-462-8782. GM's number for this recall is N212330040.

20V736000 · Air Bags:side/window:curtain:inflator

Nov 25, 2020

General Motors LLC (GM) is recalling certain 2015-2016 GMC Sierra 1500 and Chevrolet Silverado 1500 and 2015 GMC Sierra 2500 and 3500, and Chevrolet Silverado 2500 and 3500 trucks. The roof-rail air bag (RRAB) inflator end cap may detach from the inflator.

Consequence & remedy

Consequence: If the end cap separates from the inflator, the compressed gas will escape and the end cap can be propelled into the vehicle, increasing the risk of injury or a crash.

Remedy: GM will notify owners, and dealers will replace the RRAB modules on the left and/or right side, free of charge. Interim owner notification letters were mailed on December 22, 2020. Owners may contact GMC customer service at 1-888-988-7267 or Chevrolet customer service at 1-800-222-1020. Note: GM filed a new recall, number 21V-504 that supersedes this recall. All vehicles previously recalled under 20V-736 will now be repaired under the new recall number 21V-504. GM's numbers for this recall are N202309680, N202309681, and N202309682.

19V761000 · Electronic Stability Control (esc); Service Brakes; Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:wheel Speed Sensor/tone Ring

Oct 24, 2019

General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.

Consequence & remedy

Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.

Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.

Additional source detail variants (3)

Service Brakes

General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.

Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.

Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.

Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:wheel Speed Sensor/tone Ring

General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.

Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.

Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.

Electronic Stability Control (esc)

General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.

Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.

Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.

19V645000 · Service Brakes, Hydraulic:power Assist:vacuum

Sep 6, 2019

General Motors LLC (GM) is recalling certain 2015-2017 Cadillac Escalade, 2014-2018 Chevrolet Silverado, GMC Sierra, 2015-2018 Chevrolet Suburban, Tahoe, GMC Yukon vehicles. The amount of vacuum created by the vacuum pump may decrease over time.

Consequence & remedy

Consequence: As the vacuum level drops, the brake assist decreases, increasing braking effort, extending the distance required to stop the vehicle, thereby increasing the risk of a crash.

Remedy: GM will notify owners, and dealers will reprogram the Electronic Brake Control Module, free of charge. The recall began October 8, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438, Cadillac customer service at 1-800-458-8006 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192268490.

18V586000 · Steering:electric Power Assist System

Sep 7, 2018

General Motors LLC (GM) is recalling certain 2015 Chevrolet Silverado 1500, Tahoe and Suburban, GMC Sierra 1500 and Yukon, and Cadillac Escalade vehicles. Electric power steering (EPS) assist may be lost momentarily, followed by a sudden return of EPS assist.

Consequence & remedy

Consequence: If EPS assist is lost and then suddenly returns, the driver may have difficulty steering the vehicle, especially at low speeds, increasing the risk of a crash.

Remedy: GM will notify owners, and dealers will update the EPS module software, free of charge. The recall began October 12, 2018. Owners may contact Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020 and GMC customer service at 1-800-462-8782. GM's number for this recall is 18289.

18V578000 · Service Brakes, Hydraulic:pedals And Linkages

Aug 30, 2018

General Motors LLC (GM) is recalling certain 2015-2016 Chevrolet Silverado 2500, 3500, 1500 Crew Cab Special Service, Tahoe Police Pursuit/Special Service, GMC Sierra 2500, and 3500 vehicles. The brake pedal pivot nut may loosen, causing the brake pedal to be loose or inoperative.

Consequence & remedy

Consequence: If the brake pedal becomes loose or inoperative, the driver may be unable to stop the vehicle by using the brake pedal. Additionally, a loose pedal may also interfere with the accelerator pedal. Either condition may increase the risk of a crash.

Remedy: GM will notify owners, and dealers will add adhesive to the nut and reinstall the nut with increased tightness, free of charge. The recall began October 3, 2018. Owners may contact Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 18278. Note: The vehicles in this recall need this additional remedy despite being covered by recall 16V069 for brake pedal loosening.

18V291000 · Seat Belts:front

May 3, 2018

General Motors LLC (GM) is recalling certain 2015-2016 Chevrolet Silverado 1500 and Tahoe Police Pursuit and Special-Service vehicles. The flexible steel cable connecting the driver's seat belt to the outboard side of the seat may be repeatedly bent over the seat side shield as the driver enters and exits the vehicle causing the cable to fatigue and separate.

Consequence & remedy

Consequence: If the pretensioner cable becomes fatigued or breaks, the driver may not be properly restrained in the event of a crash, increasing their risk of injury.

Remedy: GM will notify owners, and dealers will replace the pretensioner cable and seat side-shield, free of charge. The recall began June 19, 2018. Owners may contact Chevrolet customer service at 1-800-222-1020. GM's number for this recall is 18156.

17V437000 · Air Bags:frontal; Air Bags:frontal:sensor/control MODULE-INACTIVE ; Seat Belts:pretensioner

Jul 10, 2017

General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.

Consequence & remedy

Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.

Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.

Additional source detail variants (3)

Seat Belts:pretensioner

General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.

Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.

Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.

Air Bags:frontal:sensor/control MODULE-INACTIVE

General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.

Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.

Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.

Air Bags:frontal

General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.

Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.

Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.

16V651000 · Air Bags:frontal; Air Bags:frontal:sensor/control MODULE-INACTIVE ; Seat Belts:pretensioner

Sep 8, 2016

General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.

Consequence & remedy

Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.

Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.

Additional source detail variants (3)

Seat Belts:pretensioner

General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.

Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.

Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.

Air Bags:frontal:sensor/control MODULE-INACTIVE

General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.

Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.

Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.

Air Bags:frontal

General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.

Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.

Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.

16V069000 · Service Brakes, Hydraulic:pedals And Linkages

Feb 5, 2016

General Motors LLC (GM) is recalling certain model year 2015-2016 Chevrolet Silverado 1500, 2500, and 3500 heavy duty trucks manufactured October 1, 2013, to February 1, 2016, 2015-2016 Chevrolet Tahoe Police Pursuit Vehicles (PPV) manufactured March 1, 2014, to February 1, 2016, and 2015-2016 GMC Sierra 2500 and 3500 heavy duty trucks manufactured October 29, 2013, to February 1, 2016. On the affected vehicles, the brake pedal pivot nut may loosen, causing the brake pedal to be loose or inoperative.

Consequence & remedy

Consequence: If the brake pedal becomes loose or inoperative, the driver may be unable to stop the vehicle by using the brake pedal. Additionally, a loose pedal may also interfere with the accelerator pedal. Either condition may increase the risk of a crash.

Remedy: GM will notify owners, and dealers will add adhesive to the brake pedal pivot nut and reinstall with an increased torque, free of charge. The recall began on March 14, 2016. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-800-462-8782. GM's number for this recall is 20760.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

2

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

PE18012 · Brake Vacuum Pump Failure

Opened Nov 20, 2018 · Closed Apr 10, 2022

Status: closed (inferred from source dates) · Service Brakes; Service Brakes, Hydraulic; Service Brakes, Hydraulic:power Assist:vacuum

On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.

Additional source detail variants (3)

Service Brakes

On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.

Service Brakes, Hydraulic

On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.

Service Brakes, Hydraulic:power Assist:vacuum

On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.