NHTSA owner reports · September 18, 2026 snapshot.
Structure complaints
90 reportsClear category filterMileage unknown · May 17, 2026
StructureUnknown Or Other
Frame failed on truck completely rusted through. The safety of my family was put at risk because the chevy dealer it was always serviced at never told me about the rust problem even though they did multi point inspections everytime it was serviced at the dealer. Only time I was ever notified about this was when it was to late to…
Read full complaint
Frame failed on truck completely rusted through. The safety of my family was put at risk because the chevy dealer it was always serviced at never told me about the rust problem even though they did multi point inspections everytime it was serviced at the dealer. Only time I was ever notified about this was when it was to late to fix. Vehicle has been looked at by a frame an Collison center and said a whole new frame is needed that it is not repairable. The Collison center also told me this is a common problem with these trucks due to the layered steel the manufacturer used to make the frame.
NHTSA ODI #11738427
Mileage unknown · Feb 22, 2026
Power TrainStructure
Unknown..... the transmission in my truck began the shutter and shake like I was running over the rumble strip. The truck was at one point locked into 4x4 and even stuck in reverse and almost got me ran over by a diesel when I couldn't get out of his way until the very last second. Im not the only one with this issue. Gm has be…
Read full complaint
Unknown..... the transmission in my truck began the shutter and shake like I was running over the rumble strip. The truck was at one point locked into 4x4 and even stuck in reverse and almost got me ran over by a diesel when I couldn't get out of his way until the very last second. Im not the only one with this issue. Gm has been knowingly mass producing these defective transmissions and selling them to the public with no notication to the consumers. This is obviously defrauding the consumers out of not only there money but also many of there livelihoods. As many families depend on there trucks in order to financially support there families. As mine does. Gm sold defective equipment. Completely aware that they where defective this is fraud and they should be held liable for there actions.
NHTSA ODI #11719674
68,500 miles · Jul 16, 2025
Structure
The contact owns a 2014 Chevrolet Silverado 1500. The contact stated that while the vehicle was parked, the contact became aware of metal fragment chippings coming from the rear subframe of the vehicle. The dealer was contacted. The vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure and referre…
Read full complaint
The contact owns a 2014 Chevrolet Silverado 1500. The contact stated that while the vehicle was parked, the contact became aware of metal fragment chippings coming from the rear subframe of the vehicle. The dealer was contacted. The vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure and referred the contact to the NHTSA hotline for assistance. The approximate failure mileage was 68,500.
NHTSA ODI #11673934
Mileage unknown · Apr 30, 2025
Power TrainStructureUnknown Or Other
Over the course of ownership the chassis of this vehicle has gotten horrendously corroded, which has caused structural components of the frame to begin to develop rust holes needing repair. These holes in the chassis are caused by the incorrect application of the factory chassis wax coating and has caused the entire frame to bec…
Read full complaint
Over the course of ownership the chassis of this vehicle has gotten horrendously corroded, which has caused structural components of the frame to begin to develop rust holes needing repair. These holes in the chassis are caused by the incorrect application of the factory chassis wax coating and has caused the entire frame to become deeply rusted through in many areas. Additionally I have been through two transmissions, the first occurring at around 55,000 miles of use, and the second around 105,000 miles. Seems there is a point of failure after around 50,000 miles on these transmissions.
NHTSA ODI #11657842
Mileage unknown · Mar 23, 2025
Structure
A well-documented and increasingly widespread problem related to excessive rust on the frames of many vehicles in this particular model year range. The cause of the problem appears to stem from a poorly applied or degrading wax coating, which, over time, peels off, leaving the frame exposed to corrosion, particularly in harsh we…
Read full complaint
A well-documented and increasingly widespread problem related to excessive rust on the frames of many vehicles in this particular model year range. The cause of the problem appears to stem from a poorly applied or degrading wax coating, which, over time, peels off, leaving the frame exposed to corrosion, particularly in harsh weather conditions such as heavy snow and road salt exposure. The result is catastrophic—my Silverado’s frame and crossmembers are now severely compromised, and the integrity of the vehicle is in question.
NHTSA ODI #11649964
72,000 miles · Mar 10, 2025
Structure
The contact owns a 2014 Chevrolet Silverado 1500. The contact stated that the headliner above the rear window had water stains. The contact stated that as a mechanic, he had inspected the vehicle and diagnosed that the water was leaking from the third brake light. The contact stated that the gasket surrounding the third brake li…
Read full complaint
The contact owns a 2014 Chevrolet Silverado 1500. The contact stated that the headliner above the rear window had water stains. The contact stated that as a mechanic, he had inspected the vehicle and diagnosed that the water was leaking from the third brake light. The contact stated that the gasket surrounding the third brake light was no longer properly sealing the third brake light. The dealer was notified of the failure and informed the contact that the VIN was not included in an unknown recall. The vehicle was not repaired. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 72,000.
NHTSA ODI #11647324
Mileage unknown · Jan 6, 2025
Structure
Frame rotted through
NHTSA ODI #11634393
Mileage unknown · Nov 2, 2024
Electrical SystemFuel/propulsion SystemStructure
I have a couple issues, check trailer wiring light, heat from air conditioner,rusty frame undercarriage - really bad , plus rocker panels on both sides rusting out, is there a recall on issues with rusting of frame ? Please help my truck only a 2014 plus had dealer work on air conditioner issues before, dealer never mentioned …
Read full complaint
I have a couple issues, check trailer wiring light, heat from air conditioner,rusty frame undercarriage - really bad , plus rocker panels on both sides rusting out, is there a recall on issues with rusting of frame ? Please help my truck only a 2014 plus had dealer work on air conditioner issues before, dealer never mentioned anything about rust on the frame, when I had multiple oil changes, and many other services done at dealer , I bought my truck from dealer in stow Ohio ! Is there any you can do to help me fix these issues?…
NHTSA ODI #11623267
Mileage unknown · Nov 1, 2024
Structure
GM has known issues with their frames rotting prematurely. We bought a 2014 Chevy Silverado 1500 in 2016 and had it undercoated at a dealership that claims it will prolong the inevitable rusting/frame rot. The truck has just under 99k miles and should be worth $15-17,000 and won't pass inspection due to severe frame rot we are t…
Read full complaint
GM has known issues with their frames rotting prematurely. We bought a 2014 Chevy Silverado 1500 in 2016 and had it undercoated at a dealership that claims it will prolong the inevitable rusting/frame rot. The truck has just under 99k miles and should be worth $15-17,000 and won't pass inspection due to severe frame rot we are told it is very unsafe and not drivable. We will be lucky to get $4,000-5,000 to trade for a part out. Our only other option is to spend $10,000 to get a new frame. GM has known about this issue and fails to do anything about it. Toyota had similar issues and stood by their name and products and replaced frames or gave consumers $10,000+ to make it right. It is not fair to the consumer we cannot win a class action against GM and demand a payout for such massive losses. Had we known our frame was so bad, we wouldn't have dropped over $5,000 in it over the last 11 months for rocker panels, cab corners, shocks, bearings, etc. We are out $15,000 on this truck and GM should be held accountable. There are thousands of people nations wide that are in the same boat hoping GM will be held liable at some-point for the distress they have cause their loyal customers.
NHTSA ODI #11623110
Mileage unknown · Oct 19, 2024
Electrical SystemStructure
My rocker panels rusting out, trailer hitch wiring issue again , air conditioning/ heater issues again , fuel sending unit and lines issues , plus was told by dealer under frame work rusting issues??? What is going on with my 2014 1500 Silverado , is there anything you can help me with regarding any , any of these issues?. Thank…
Read full complaint
My rocker panels rusting out, trailer hitch wiring issue again , air conditioning/ heater issues again , fuel sending unit and lines issues , plus was told by dealer under frame work rusting issues??? What is going on with my 2014 1500 Silverado , is there anything you can help me with regarding any , any of these issues?. Thanks [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
NHTSA ODI #11620759
Official recalls
6Apr 8, 2021
General Motors, LLC (GM) is recalling certain 2014-2016 Chevrolet Silverado 1500, 2015-2016 Chevrolet Tahoe, and 2014-2015 GMC Sierra 1500 vehicles that may have received an incorrect replacement tensioner cable assembly as part of a previous recall remedy or a subsequent repair. The flexible steel cable connecting the driver's seat belt to the outboard side of the seat may be repeatedly bent over the seat side shield as the driver enters and exits the vehicle causing the cable to fatigue and separate.
Consequence & remedy
Consequence: A broken pretensioner cable reduces the effectiveness of the driver's seat belt, increasing the risk of injury.
Remedy: GM will notify owners, and dealers will replace the driver seat belt lap pretensioner, free of charge. The recall began on May 5, 2021. Owners may contact Chevrolet customer service at 1-800-222-1020, and GMC customer service at 1-800-462-8782. GM's number for this recall is N212330040.
Oct 24, 2019
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence & remedy
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Additional source detail variants (3)
Service Brakes
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:wheel Speed Sensor/tone Ring
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Electronic Stability Control (esc)
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Sep 6, 2019
General Motors LLC (GM) is recalling certain 2015-2017 Cadillac Escalade, 2014-2018 Chevrolet Silverado, GMC Sierra, 2015-2018 Chevrolet Suburban, Tahoe, GMC Yukon vehicles. The amount of vacuum created by the vacuum pump may decrease over time.
Consequence & remedy
Consequence: As the vacuum level drops, the brake assist decreases, increasing braking effort, extending the distance required to stop the vehicle, thereby increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the Electronic Brake Control Module, free of charge. The recall began October 8, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438, Cadillac customer service at 1-800-458-8006 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192268490.
Jul 10, 2017
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence & remedy
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Additional source detail variants (3)
Seat Belts:pretensioner
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Air Bags:frontal:sensor/control MODULE-INACTIVE
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Air Bags:frontal
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Jun 29, 2017
General Motors LLC (GM) is recalling certain 2014 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles. The vehicles may have a temporary loss of electric power steering (EPS) assist, especially during low-speed turning maneuvers.
Consequence & remedy
Consequence: If EPS assist is lost and then returns, the driver might lose temporary control of the steering wheel, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will update the EPS module software, free of charge. The recall began on August 10, 2017. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-800-432-8782. GM's number for this recall is 17276.
Sep 8, 2016
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence & remedy
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Additional source detail variants (3)
Seat Belts:pretensioner
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Air Bags:frontal:sensor/control MODULE-INACTIVE
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Air Bags:frontal
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
PE18012 · Brake Vacuum Pump Failure
Opened Nov 20, 2018 · Closed Apr 10, 2022
Status: closed (inferred from source dates) · Service Brakes; Service Brakes, Hydraulic; Service Brakes, Hydraulic:power Assist:vacuum
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Additional source detail variants (3)
Service Brakes
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Service Brakes, Hydraulic
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Service Brakes, Hydraulic:power Assist:vacuum
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Illustration