NHTSA owner reports · September 18, 2026 snapshot.
Service Brakes complaints
269 reportsClear category filter82,000 miles · Oct 29, 2019
Service BrakesCrashInjury
TL* THE CONTACT OWNS A 2014 CHEVROLET SILVERADO 1500. WHILE DRIVING 30 MPH AND MAKING A RIGHT TURN, THE CONTACT DEPRESSED THE BRAKE PEDAL, BUT THE VEHICLE DID NOT STOP. AS A RESULT, THE CONTACT REAR ENDED ANOTHER VEHICLE. THE AIR BAGS DID NOT DEPLOY. THE CONTACT SUSTAINED A WHIPLASH THAT REQUIRED MEDICAL ATTENTION, BUT THE CONTA…
Read full complaint
TL* THE CONTACT OWNS A 2014 CHEVROLET SILVERADO 1500. WHILE DRIVING 30 MPH AND MAKING A RIGHT TURN, THE CONTACT DEPRESSED THE BRAKE PEDAL, BUT THE VEHICLE DID NOT STOP. AS A RESULT, THE CONTACT REAR ENDED ANOTHER VEHICLE. THE AIR BAGS DID NOT DEPLOY. THE CONTACT SUSTAINED A WHIPLASH THAT REQUIRED MEDICAL ATTENTION, BUT THE CONTACT DENIED ASSISTANCE. A POLICE REPORT WAS FILED. THE POLICE TOWED THE VEHICLE TO A TOW LOT. THE INSURANCE COMPANY WAS NOT CONTACTED. THE VEHICLE WAS LATER TAKEN TO THE CONTACT'S RESIDENCE. THE DEALER AND MANUFACTURER WERE NOT CONTACTED. THE CAUSE OF THE FAILURE WAS NOT DETERMINED. THE FAILURE MILEAGE WAS APPROXIMATELY 82,000.
NHTSA ODI #11276900
18,000 miles · Oct 23, 2019
Electrical SystemService Brakes
TL* THE CONTACT OWNS A 2014 CHEVROLET SILVERADO 1500. THE CONTACT RECEIVED A RECALL NOTICE FOR NHTSA CAMPAIGN NUMBER: 19V645000 (SERVICE BRAKES, HYDRAULIC). WHEN THE VEHICLE WAS STARTED, THE IGNITION SWITCH SEIZED AND FAILED TO RELEASE THE KEY WHILE THE BRAKE PEDAL WAS DEPRESSED. THERE WERE NO WARNING INDICATORS ILLUMINATED. THE…
Read full complaint
TL* THE CONTACT OWNS A 2014 CHEVROLET SILVERADO 1500. THE CONTACT RECEIVED A RECALL NOTICE FOR NHTSA CAMPAIGN NUMBER: 19V645000 (SERVICE BRAKES, HYDRAULIC). WHEN THE VEHICLE WAS STARTED, THE IGNITION SWITCH SEIZED AND FAILED TO RELEASE THE KEY WHILE THE BRAKE PEDAL WAS DEPRESSED. THERE WERE NO WARNING INDICATORS ILLUMINATED. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER AND DEALER WERE NOT CONTACTED. THE FAILURE MILEAGE WAS 18,000.
NHTSA ODI #11270444
72,000 miles · Oct 23, 2019
Service Brakes
TL* THE CONTACT OWNS A 2014 CHEVROLET SILVERADO 1500. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 19V645000 (SERVICE BRAKES, HYDRAULIC). WHILE DRIVING, THE VEHICLE DID NOT RESPOND IMMEDIATELY WHEN THE BRAKE PEDAL WAS DEPRESSED. THERE WERE NO WARNING INDICATORS ILLUMINATED. THE FAILURE RECURRED. THE MANUFACTURER W…
Read full complaint
TL* THE CONTACT OWNS A 2014 CHEVROLET SILVERADO 1500. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 19V645000 (SERVICE BRAKES, HYDRAULIC). WHILE DRIVING, THE VEHICLE DID NOT RESPOND IMMEDIATELY WHEN THE BRAKE PEDAL WAS DEPRESSED. THERE WERE NO WARNING INDICATORS ILLUMINATED. THE FAILURE RECURRED. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE AND STATED THAT THE RECALL WOULD BE REPAIRED BASED ON THE REMEDY EXPLAINED IN THE RECALL NOTICE. THE RECALL DETAILS WERE NOT PROVIDED. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE FAILURE MILEAGE WAS APPROXIMATELY 72,000. PARTS DISTRIBUTION DISCONNECT.
NHTSA ODI #11270417
51,000 miles · Oct 21, 2019
Electrical SystemService BrakesSteering
TL* THE CONTACT OWNS A 2014 CHEVROLET SILVERADO 1500. WHEN THE BRAKE PEDAL WAS DEPRESSED, THE POWER ASSIST WARNING INDICATOR ILLUMINATED, THE POWER ASSIST FAILED, THE DOORS WOULD UNLOCK AND LOCK INTERMITTENTLY, THE AIR BAG WARNING INDICATOR ILLUMINATED, AND THE AIR CONDITIONING WOULD TURN ON AND OFF INTERMITTENTLY. THE CONTACT S…
Read full complaint
TL* THE CONTACT OWNS A 2014 CHEVROLET SILVERADO 1500. WHEN THE BRAKE PEDAL WAS DEPRESSED, THE POWER ASSIST WARNING INDICATOR ILLUMINATED, THE POWER ASSIST FAILED, THE DOORS WOULD UNLOCK AND LOCK INTERMITTENTLY, THE AIR BAG WARNING INDICATOR ILLUMINATED, AND THE AIR CONDITIONING WOULD TURN ON AND OFF INTERMITTENTLY. THE CONTACT STATED THAT THE FAILURES BECAME MORE PERSISTENT AFTER HAVING THE VEHICLE REPAIRED PER AN UNKNOWN RECALL INVOLVING THE BRAKES. TOM BELL CHEVROLET (LOCATED AT 800 ALABAMA ST, REDLANDS, CA 92374, 909-748-1833) WAS CONTACTED AND STATED THAT THERE WAS NO RECALL FOR THE FAILURES. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOT INFORMED OF THE FAILURES. THE APPROXIMATE FAILURE MILEAGE WAS 51,000.
NHTSA ODI #11269895
99,000 miles · Oct 16, 2019
EngineService Brakes
TL* THE CONTACT OWNS A 2014 CHEVROLET SILVERADO 1500. THE CONTACT RECEIVED A RECALL NOTIFICATION FOR NHTSA CAMPAIGN NUMBER: 19V645000 (SERVICE BRAKES, HYDRAULIC). THE CONTACT TOOK THE VEHICLE TO BONIFACE HIERS CHEVROLET (800 S HARBOR CITY BLVD, MELBOURNE, FL 32901, (321) 723-3611) WHERE THE VEHICLE WAS REPAIRED; HOWEVER, THE FAI…
Read full complaint
TL* THE CONTACT OWNS A 2014 CHEVROLET SILVERADO 1500. THE CONTACT RECEIVED A RECALL NOTIFICATION FOR NHTSA CAMPAIGN NUMBER: 19V645000 (SERVICE BRAKES, HYDRAULIC). THE CONTACT TOOK THE VEHICLE TO BONIFACE HIERS CHEVROLET (800 S HARBOR CITY BLVD, MELBOURNE, FL 32901, (321) 723-3611) WHERE THE VEHICLE WAS REPAIRED; HOWEVER, THE FAILURE RECURRED. THE CONTACT STATED THAT EACH TIME WHEN DRIVING, MAKING A TURN, AND DEPRESSING THE BRAKE PEDAL, THE VEHICLE STALLED AND THE STEERING WHEEL FAILED TO TURN. THE CONTACT PLACED THE GEAR INTO NEUTRAL TO RESTART THE ENGINE. THE VEHICLE WAS RESTARTED AND WAS ABLE TO DRIVE NORMALLY. THE KEY HAD TO BE USED MANUALLY TO START THE VEHICLE WHEN THE FAILURE OCCURRED AND AN UNKNOWN WARNING INDICATOR ILLUMINATED. THE VEHICLE WAS NOT TAKEN TO A DEALER OR AN INDEPENDENT MECHANIC FOR DIAGNOSTIC TESTING. THE MANUFACTURER WAS NOT MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS APPROXIMATELY 99,000.
NHTSA ODI #11268904
81,000 miles · Oct 9, 2019
Service Brakes
TL* THE CONTACT OWNS A 2014 CHEVROLET SILVERADO 1500. WHILE DRIVING APPROXIMATELY 20 MPH, THE BRAKE PEDAL WAS DEPRESSED, BUT REQUIRED EXTRA EFFORT TO SLOW DOWN THE VEHICLE. THE VEHICLE WAS TAKEN TO MARMIE CHEVROLET (1724 10TH ST, GREAT BEND, KS 67530, (620) 792-2571) TO BE DIAGNOSED AND THE CONTACT WAS INFORMED THAT THE VEHICLE …
Read full complaint
TL* THE CONTACT OWNS A 2014 CHEVROLET SILVERADO 1500. WHILE DRIVING APPROXIMATELY 20 MPH, THE BRAKE PEDAL WAS DEPRESSED, BUT REQUIRED EXTRA EFFORT TO SLOW DOWN THE VEHICLE. THE VEHICLE WAS TAKEN TO MARMIE CHEVROLET (1724 10TH ST, GREAT BEND, KS 67530, (620) 792-2571) TO BE DIAGNOSED AND THE CONTACT WAS INFORMED THAT THE VEHICLE WAS INCLUDED IN NHTSA CAMPAIGN NUMBER: 19V645000 (SERVICE BRAKES, HYDRAULIC). THE RECALL REPAIR WAS PERFORMED, BUT THE CONTACT WAS INFORMED THAT THE VACUUM PUMP ALSO NEEDED TO BE REPLACED. THE VEHICLE WAS REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 81,000.
NHTSA ODI #11267331
17,860 miles · Sep 23, 2019
Air BagsService BrakesStructureCrashFire
THERE WAS A DEATH IN THIS VEHICLE ON A STATE HIGHWAY GA I-20 WB. POLICE REPORTS WERE FILED. THE VEHICLE WAS UNSALVAGABLE. RECALLS ISSUED ARE DATED AFTER THIS DATE.
NHTSA ODI #11257382
147,310 miles · Sep 18, 2019
Service Brakes
TL* THE CONTACT OWNS A 2014 CHEVROLET SILVERADO 1500. THE CONTACT RECEIVED AN UNKNOWN RECALL NOTICE REGARDING THE SERVICE BRAKES, HYDRAULIC. WHILE DRIVING VARIOUS SPEEDS, THE BRAKE PEDAL WAS DIFFICULT TO DEPRESS. THE CONTACT ALSO HEARD AN ABNORMAL GURGLING NOISE EMERGING FROM THE VEHICLE. THE BRAKE ASSIST WARNING INDICATOR ILLUM…
Read full complaint
TL* THE CONTACT OWNS A 2014 CHEVROLET SILVERADO 1500. THE CONTACT RECEIVED AN UNKNOWN RECALL NOTICE REGARDING THE SERVICE BRAKES, HYDRAULIC. WHILE DRIVING VARIOUS SPEEDS, THE BRAKE PEDAL WAS DIFFICULT TO DEPRESS. THE CONTACT ALSO HEARD AN ABNORMAL GURGLING NOISE EMERGING FROM THE VEHICLE. THE BRAKE ASSIST WARNING INDICATOR ILLUMINATED. THE VEHICLE WAS TAKEN TO ROYAL CHEVROLET (4502 W BROAD ST, RICHMOND, VA 23230, (804) 441-9393) WHERE IT WAS DIAGNOSED THAT THE BRAKE PUMP, BRAKE VACUUM BOOSTER, AND BRAKE LINES WERE FULL OF OIL AND A GASKET WAS EXPANDED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOT CONTACTED. THE FAILURE MILEAGE WAS 147,310. THE VIN WAS INVALID.
NHTSA ODI #11256358
147,310 miles · Sep 18, 2019
Service Brakes
TL* THE CONTACT OWNS A 2014 CHEVROLET SILVERADO 1500. THE CONTACT RECEIVED AN UNKNOWN RECALL NOTICE REGARDING THE SERVICE BRAKES, HYDRAULIC. WHILE DRIVING VARIOUS SPEEDS, THE BRAKE PEDAL WAS DIFFICULT TO DEPRESS. THE CONTACT ALSO HEARD AN ABNORMAL GURGLING NOISE EMERGING FROM THE VEHICLE. THE BRAKE ASSIST WARNING INDICATOR ILLUM…
Read full complaint
TL* THE CONTACT OWNS A 2014 CHEVROLET SILVERADO 1500. THE CONTACT RECEIVED AN UNKNOWN RECALL NOTICE REGARDING THE SERVICE BRAKES, HYDRAULIC. WHILE DRIVING VARIOUS SPEEDS, THE BRAKE PEDAL WAS DIFFICULT TO DEPRESS. THE CONTACT ALSO HEARD AN ABNORMAL GURGLING NOISE EMERGING FROM THE VEHICLE. THE BRAKE ASSIST WARNING INDICATOR ILLUMINATED. THE VEHICLE WAS TAKEN TO ROYAL CHEVROLET (4502 W BROAD ST, RICHMOND, VA 23230, (804) 441-9393) WHERE IT WAS DIAGNOSED THAT THE BRAKE PUMP, BRAKE VACUUM BOOSTER, AND BRAKE LINES WERE FULL OF OIL AND A GASKET WAS EXPANDED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOT CONTACTED. THE FAILURE MILEAGE WAS 147,310.
NHTSA ODI #11256355
114,000 miles · Sep 11, 2019
Service Brakes
TL* THE CONTACT OWNS A 2014 CHEVROLET SILVERADO 1500. WHILE DRIVING APPROXIMATELY 5 MPH, THE BRAKE PEDAL BECAME HARD TO DEPRESS, THE CONTACT HAD TO APPLY EXCESSIVE PRESSURE TO STOP THE VEHICLE. THE CONTACT ALSO MENTIONED RECEIVING AN UNKNOWN TECHNICAL SERVICE BULLETIN (TSB) SIX MONTHS AGO IN REFERENCE TO THE BRAKES, WHICH TURNED…
Read full complaint
TL* THE CONTACT OWNS A 2014 CHEVROLET SILVERADO 1500. WHILE DRIVING APPROXIMATELY 5 MPH, THE BRAKE PEDAL BECAME HARD TO DEPRESS, THE CONTACT HAD TO APPLY EXCESSIVE PRESSURE TO STOP THE VEHICLE. THE CONTACT ALSO MENTIONED RECEIVING AN UNKNOWN TECHNICAL SERVICE BULLETIN (TSB) SIX MONTHS AGO IN REFERENCE TO THE BRAKES, WHICH TURNED INTO NHTSA CAMPAIGN NUMBER: 19V645000 (SERVICE BRAKES, HYDRAULIC). THE VEHICLE WAS NOT TAKEN TO THE DEALER FOR DIAGNOSTIC TESTING. WHEN THE TSB WAS RECEIVED, THE CONTACT CALLED CLIFF ANSCHUETZ CHEVROLET (1074 US 23 N, ALPENA MI, 49707) AND WAS INFORMED THAT THE VEHICLE EXCEEDED THE MILEAGE TO BE REPAIRED PER THE RECALL. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 114,000.
NHTSA ODI #11254670
Official recalls
6Apr 8, 2021
General Motors, LLC (GM) is recalling certain 2014-2016 Chevrolet Silverado 1500, 2015-2016 Chevrolet Tahoe, and 2014-2015 GMC Sierra 1500 vehicles that may have received an incorrect replacement tensioner cable assembly as part of a previous recall remedy or a subsequent repair. The flexible steel cable connecting the driver's seat belt to the outboard side of the seat may be repeatedly bent over the seat side shield as the driver enters and exits the vehicle causing the cable to fatigue and separate.
Consequence & remedy
Consequence: A broken pretensioner cable reduces the effectiveness of the driver's seat belt, increasing the risk of injury.
Remedy: GM will notify owners, and dealers will replace the driver seat belt lap pretensioner, free of charge. The recall began on May 5, 2021. Owners may contact Chevrolet customer service at 1-800-222-1020, and GMC customer service at 1-800-462-8782. GM's number for this recall is N212330040.
Oct 24, 2019
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence & remedy
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Additional source detail variants (3)
Service Brakes
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:wheel Speed Sensor/tone Ring
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Electronic Stability Control (esc)
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Sep 6, 2019
General Motors LLC (GM) is recalling certain 2015-2017 Cadillac Escalade, 2014-2018 Chevrolet Silverado, GMC Sierra, 2015-2018 Chevrolet Suburban, Tahoe, GMC Yukon vehicles. The amount of vacuum created by the vacuum pump may decrease over time.
Consequence & remedy
Consequence: As the vacuum level drops, the brake assist decreases, increasing braking effort, extending the distance required to stop the vehicle, thereby increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the Electronic Brake Control Module, free of charge. The recall began October 8, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438, Cadillac customer service at 1-800-458-8006 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192268490.
Jul 10, 2017
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence & remedy
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Additional source detail variants (3)
Seat Belts:pretensioner
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Air Bags:frontal:sensor/control MODULE-INACTIVE
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Air Bags:frontal
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Jun 29, 2017
General Motors LLC (GM) is recalling certain 2014 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles. The vehicles may have a temporary loss of electric power steering (EPS) assist, especially during low-speed turning maneuvers.
Consequence & remedy
Consequence: If EPS assist is lost and then returns, the driver might lose temporary control of the steering wheel, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will update the EPS module software, free of charge. The recall began on August 10, 2017. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-800-432-8782. GM's number for this recall is 17276.
Sep 8, 2016
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence & remedy
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Additional source detail variants (3)
Seat Belts:pretensioner
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Air Bags:frontal:sensor/control MODULE-INACTIVE
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Air Bags:frontal
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
PE18012 · Brake Vacuum Pump Failure
Opened Nov 20, 2018 · Closed Apr 10, 2022
Status: closed (inferred from source dates) · Service Brakes; Service Brakes, Hydraulic; Service Brakes, Hydraulic:power Assist:vacuum
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Additional source detail variants (3)
Service Brakes
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Service Brakes, Hydraulic
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Service Brakes, Hydraulic:power Assist:vacuum
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Illustration