IllustrationCRACKED DASH ABOVE THE DRIVER SIDE AND AROUND THE PASSENGER SIDE AIRBAG. DUE TO EITHER CHEAP MATERIAL OR DEFECT IN MATERIAL. VEHICLE IS GARAGE KEPT AND WAS STATIONARY WHEN CRACKS APPEARED ON BOTH SIDES. GARAGE TEMPERATURE WAS 76 DEGREES THE DAY CRACKS HAPPENED.
2013 Chevrolet Silverado 1500
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2013 Chevrolet Silverado 1500 do not stand out strongly from the model-year median of 525.
About this comparison →How this year compares
Owner complaints by model year
Compare all Silverado 1500 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
240–25K
4225–50K
4350–75K
2775–100K
27100–150K
7150K+
170 reports with mileage · 131 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Air Bags. Review the 83 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Structure. Review the 75 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 33 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
8 crash reports0 fire reports4 injury reports
What owners actually said
301 reportsTHE WARNING LIGHTS FOR STABILITY AND TRACTION HAVE COME ON. THE DASHBOARD IS CRACKING BADLY AND PIECES ARE FALLING OFF. *TR
CRACKED DASH. *TR
TL* THE CONTACT OWNS A 2013 CHEVROLET SILVERADO 1500. THE CONTACT STATED THAT THERE WAS AN ABNORMAL SOUND COMING FROM THE BRAKES. THE STABILI TRAK SYSTEM ON WARNING LIGHT WAS ILLUMINATED AS WELL AS ANOTHER UNKNOWN WARNING LIGHT. THE VEHICLE WAS TAKEN TO THE AMIGO CHEVROLET LOCATED AT 1900 S 2ND ST, GALLUP, NM 87301, (505) 726-43…
Read full complaint
TL* THE CONTACT OWNS A 2013 CHEVROLET SILVERADO 1500. THE CONTACT STATED THAT THERE WAS AN ABNORMAL SOUND COMING FROM THE BRAKES. THE STABILI TRAK SYSTEM ON WARNING LIGHT WAS ILLUMINATED AS WELL AS ANOTHER UNKNOWN WARNING LIGHT. THE VEHICLE WAS TAKEN TO THE AMIGO CHEVROLET LOCATED AT 1900 S 2ND ST, GALLUP, NM 87301, (505) 726-4329, WHERE THE BRAKE WAS REPAIRED. THE CONTACT WAS UNAWARE OF EXACTLY WHAT REPAIR WAS PERFORMED. THE FAILURE RECURRED. THE MANUFACTURER WAS NOT MADE AWARE OF THE FAILURE. THE VEHICLE WAS NOT REPAIRED A SECOND TIME. THE FAILURE MILEAGE WAS APPROXIMATELY 88,000. *BF CONSUMER STATES THAT SOUND IS HEARD WHEN BRAKES ARE PRESSED. CONSUMER SAYS WHEN ENGINE IS STARTED SERVICE TRACTION CONTROL AND STAGILITRACK LIGHTS COME ON DASHBOARD. CONSUMER SAYS THAT THE PROBLEM IS WITH THE ROTATION OR ALIGNMENT AND AXLE BOOTS OR JOINTS FROM TIRE ROTATION. CONSUMER REPORTED ISSUE TO DEALER ON 06/02/20 AND WAS TOLD THAT THEY WOULD HAVE TO PAY FOR REPAIRS. *DL
THE DASH AREA AROUND THE PASSENGER AIRBAG COVER IS CRACKED AND WOULD BE A FLYING DEBRIS HAZARD IN AN ACCIDENT, ESPECIALLY IF THE AIRBAG WERE TO DEPLOY. IN ADDITION CRACKS EXIST DIRECTLY IN FRONT OF THE STEERING COLUMN THAT, WHEN THE SUN HITS IT, CREATES A GLARE THAT AFFECTS VISIBILITY. BOTH OF THESE ARE SAFETY CONCERNS AND GM SA…
Read full complaint
THE DASH AREA AROUND THE PASSENGER AIRBAG COVER IS CRACKED AND WOULD BE A FLYING DEBRIS HAZARD IN AN ACCIDENT, ESPECIALLY IF THE AIRBAG WERE TO DEPLOY. IN ADDITION CRACKS EXIST DIRECTLY IN FRONT OF THE STEERING COLUMN THAT, WHEN THE SUN HITS IT, CREATES A GLARE THAT AFFECTS VISIBILITY. BOTH OF THESE ARE SAFETY CONCERNS AND GM SAID THAT ITS NORMAL. HOW IS ANYTHING THAT CAN BECOME FLYING SHRAPNEL OR BLINDING THE DRIVER NOT A CONCERN OR NORMAL. THIS NEEDS TO BE RESOLVED BEFORE SOMEONE GETS SERIOUSLY HURT. THESE CRACKS APPEARED OVER A YEAR AGO BUT THEY'VE NOW GOTTEN WORSE AND THE GLARE HAS BECOME MORE OF AN ISSUE. *TR
THE DASHBOARD IN MY PICKUP HAS CRACKED FROM ONE SIDE TO THE OTHER AND I AM AFRAID THAT IF I AM IN AN ACCIDENT THAT THERE WILL BE AIRBORNE PIECES OF PLASTIC THAT WILL BECOME A HAZARD. *TR
THE DASH SURROUNDING THE PASSENGER AIRBAG IS CRACKING IN THE UPPER CORNERS. ALSO IT'S CRACKING IN FRONT OF THE DRIVER SIDE. AN ACCIDENT COULD LEAD TO PIECES OF THE DASH BREAKING AND CAUSING INJURY OR DEATH TO PASSENGERS. *TR
DASH HAS CRACKED IN 2 DIFFERENT SPOTS. *TR
AFM SYSTEM CAUSES CYLINDERS 1 AND 7 TO FOUL THE SPARK PLUGS ACTUALLY CAUSING THE PORCELAIN TO BREAK OFF IN THE COMBUSTION CHAMBER. THE AFM IS OBVIOUSLY AN ENGINEERING FAILURE AND SHOULD HAVE BEEN RECALLED AND REPAIRED UNDER WARRANTY. PREVIOUS FIXES DO NOT WORK. MODIFYING THE VALVE COVER TO CORRECT A DESIGN FLAW IS NOT A CURE FOR…
Read full complaint
AFM SYSTEM CAUSES CYLINDERS 1 AND 7 TO FOUL THE SPARK PLUGS ACTUALLY CAUSING THE PORCELAIN TO BREAK OFF IN THE COMBUSTION CHAMBER. THE AFM IS OBVIOUSLY AN ENGINEERING FAILURE AND SHOULD HAVE BEEN RECALLED AND REPAIRED UNDER WARRANTY. PREVIOUS FIXES DO NOT WORK. MODIFYING THE VALVE COVER TO CORRECT A DESIGN FLAW IS NOT A CURE FOR THE REAL PROBLEM, WHICH IS A DESIGN FLAW. #1 AND #7 FOUL OUT DUE TO THE COLLECTION OF CARBON DEPOSIT CAUSED FROM EXCESS OIL IN THESE CHAMBERS WHICH CAUSES THE MALFUNCTION ENGINE LIGHT TO COME ON AND THE EVENTUAL CATALYTIC CONVERTOR FAILURE, POOR GAS MILEAGE AND POOR OVERALL PERFORMANCE, WITH EVENTUAL ENGINE FAILURE. LACK OF ACCELERATION, SLOW PERFORMANCE. FIRST NOTICED AT AROUND 30 TO 50,000 MILES AND PROGRESSIVELY BECAME WORSE. IDLE IS POOR DUE TO FOULED AND BROKEN PLUGS IN THESE TWO CYLINDERS AND THE ECU ATTEMPTING TO CORRECT THE ERROR THE BALANCE OF ENGINE IS THROWN INTO A UNBALANCED CONDITION CAUSING THE BUILDUP OF CARBON DEPOSITS IN THE ENGINE AND CAUSING THE SENSORS TO ATTEMPT TO CORRECT THE PROBLEM. PROBLEM IS UNIVERSAL AND NOT SPECIFIC TO A FEW SELECT VEHICLES BUT TO THOSE WITH THE AFM SYSTEM AND WAS OBVIOUSLY A PROBLEM SEVERE ENOUGH FOR GM TO CHANGE TO THE NEWLY DEVELOPED DFM SYSTEM WITHOUT ATTEMPTING TO ACTUALLY ADDRESS THE FLAWED AFM PROBLEM.
CRACKED DASH. LIFTER FROM 8 TO 4 CYLINDER BREAK DOWN. 4000 FIX
Official recalls
221V053000 · Air Bags:frontal:passenger Side:inflator Module
Feb 5, 2021
General Motors, LLC (GM) is recalling certain 2013 Cadillac Escalade, Escalade ESV, and Escalade EXT, Chevrolet Avalanche, Silverado 1500, Silverado 2500/3500, Suburban, Tahoe, GMC Sierra 1500, Sierra 2500/3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, GM is recalling certain 2010 Cadillac Escalade, Escalade ESV, and Escalade EXT, Chevrolet Avalanche, Silverado 1500, Silverado 2500/3500, Suburban, Tahoe, GMC Sierra 1500, Sierra 2500/3500, Yukon, and Yukon XL vehicles originally sold, or ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Additionally, GM is recalling certain 2009 Cadillac Escalade, Escalade ESV, and Escalade EXT, Chevrolet Avalanche, Silverado 1500, Silverado 2500/3500, Suburban, Tahoe, GMC Sierra 1500, Sierra 2500/3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C."
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 24, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed on May 11, 2021. Owners may contact Cadillac customer service at 1-800-458-8006; Chevrolet customer service at 1-800-222-1020; and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328790.
21V054000 · Air Bags:frontal:passenger Side:inflator Module
Feb 5, 2021
General Motors, LLC (GM) is recalling certain 2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of AL, CA, FL, GA, HI, LA, MS, SC, TX, PR, AS, GU, the MP, and VI or "Zone A." Additionally GM is recalling certain 2011-2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, Yukon XL and 2011-2013 Cadillac Escalade EXT, Chevrolet Avalanche, Silverado 1500, and GMC Sierra 1500 vehicles originally sold, or ever registered, in the states of AZ, AR, DE, DC, IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV or "Zone B." Additionally, GM is recalling certain 2010-2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, and Yukon XL and 2010-2013 Cadillac Escalade EXT, Chevrolet Avalanche, Silverado 1500, and GMC Sierra 1500 vehicles originally sold, or ever registered, in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY or "Zone C." These vehicles are equipped with non-desiccated passenger frontal inflators containing phase-stabilized ammonium nitrate (PSAN) propellant. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 25, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed to 40 VIN owners on May 11, 2021. A second owner notification letter was mailed to all other owners on January 24, 2022. Owners may contact Chevrolet customer service at 1-800-222-1020; Cadillac customer service at 1-800-458-8006; and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328800.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2DP22005 · Pedestrian Alert Sounds
Opened Jan 27, 2023 · Closed Aug 7, 2023
Status: closed (inferred from source dates) · Electrical System:propulsion System
NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.
EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.