2016 Chevrolet Malibu

The vehicle went into shift to park and will not turn off. This is a known problem with ALL GM vehicles that hasn’t been fixed or offered a warranty for. It’s dangerous and causes the car not to move shut off in traffic and drains the battery. My car currently isn’t working due to this issue and the repair to fix is too much with no assistance from GM for a known defect. My car was almost hit because of the car had to be towed because it’s unable to be moved.

The contact owns a 2016 Chevrolet Malibu. The contact stated that while driving at an undisclosed speed, the accelerator pedal was depressed; however, the vehicle failed to accelerate. In addition, the vehicle occasionally accelerated independently. The contact stated that several unknown warning lights were illuminated, and the engine seized. The contact stated that the vehicle was jump-started daily, and the unknown warning lights turned off when the vehicle started. The vehicle was taken to the dealer; however, the failure was not duplicated. The vehicle was taken to several independent mechanics; however, the failure was not duplicated. In addition, the vehicle was taken back to the dealer where the vehicle was purchased; however, the failure was not duplicated. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The manufacturer was not made aware of the failure. The failure mileage was approximately 90,000.

My 2016 Malibu has a severe EBCM-related safety defect causing all four brakes to drag and overheat (reaching 240°F), leading to unstable handling. This condition mirrors the 2016 Malibu EBCM recall (GM Recall 39440). I sought help from GM. A GM-certified dealer-Monken in Centralia, IL performed a “diagnostic scan” which documented the core hydraulic failure: a constant, uncommanded 6.839 psi residual brake line pressure when the pedal was released. (A healthy system should be near 0 psi) This 6.839 psi is actively forcing the brakes to drag. The dealer ignored their own scientific data and submitted a fraudulent diagnosis of ("rust buildup") to GM, which GM used to deny the claim based on mileage. “Rust buildup” doesn’t create hydraulic pressure. GM is aware of this specific, documented, quantifiable safety defect (the 6.839 psi pressure) and is refusing to investigate it further. I stressed to GM that the vehicle wasn’t safe to drive and that I have a small child who has to ride in the car with me. GM dismissed my concerns by stating the dealership won’t release my car unless its safe to drive. I then had to drive the car 22 miles back home with all 4 brakes dragging. I requested the full diagnostic scan report (that the mechanic confirmed he could provide me with when I dropped my car off there) numerous times and never did I get one. I informed them that I would be filing a complaint hadn’t I received it by a certain time. The new kid in service then did send me screenshots of a generic OBDII scanner where I saw the 6.839 psi. I knew what the issue was prior to taking my car to Monken. I had an independent scan done prior. I only took the car there to comply with GM’s protocol to be eligible for assistance. I am requesting NHTSA investigate GM for failure to address a documented hydraulic control safety defect that causes brake dragging and overheating, which is non-compliant with safety standards. I can give further info Please call me for further details.

The contact owns a 2016 Chevrolet Malibu. The contact stated that after driving and parking the vehicle, the contact entered the residence; however, upon returning to the vehicle, the vehicle failed to start. There were no warning lights illuminated. The vehicle was towed to the local dealer, and the contact was informed that the battery needed to be replaced. The battery was replaced. The vehicle was diagnosed, and determined that the camshaft, fuel vacuum pump, and camshaft sensor needed to be replaced. The Oxygen sensors were replaced. The vehicle was not repaired. The manufacturer was not contacted. The failure mileage was approximately 146,000.

The engine power reduced came light came on along with service stability trac. The car would stall after going into auto stop and just shut off. In certain instances it would shutoff when slowed down enough. It was brought in for service where the turbo charge solenoid starter and catalytic converter annd alternator all were replaced due to the turbo braking into pieces and being lodged into the converter and engine. Less than a week later the car returned to stalling at the auto stop feature. When brought in for service it was linked to the alternator and engine control module and mass air flow sensor. The car was then serviced again six months later for the alternator again. Now the car is once again stuck in engine power reduced with no direct codes linked to the problem and the starter was replaced and now the engine is remaining in limp mode. The car has stalled multiple times on not only at stop lights but on the highway and while turning at busy intersections causing traffic jams and even a side collision. The engine light as remained on since the day I got the car.