2016 Chevrolet Malibu

“Steering assist is reduced, drive with care” is showing up for a couple second and disappearing. When that happens my car seems to shut off and the steering wheel stiffens and pull to either the left of right side. All this happens while driving. After the 3rd time of it happening within 10min, my gas fuel level dropped but when back up to the “original” level

My car will rev up to 4000 rpm’s and my car will not go about 20 mph. My cruise stopped working after my car went into reduce engine power. The dealership said they fixed all issues but was back to doing the high rev within a week. It started this week telling me to shift to park even though my car was in park. The shift to park cable has been replaced twice now. I have been dealing with this since July of 2025. My car has been in the shop more times than I can count.

I am reporting a recurring safety defect related to GM’s known “Shift to Park” issue. My vehicle displays a “Shift to Park” warning even when the vehicle is already in park, preventing the car from shutting off properly and creating a safety risk. This issue has been widely reported and associated with GM recalls and service bulletins. GM previously repaired this issue once while my vehicle was under warranty, acknowledging it as a known defect. The same defect has now reoccurred after the warranty period expired. GM is refusing to repair it again, despite the issue being recall-related and tied to a known defective design rather than wear and tear. This defect affects safe vehicle operation, risks battery drain, rollaway hazards, and driver distraction. I believe this is an unresolved safety defect that should be covered regardless of warranty status.

On December 16, 2025 the check engine light and service stabiltrek warning light appeared on my 2016 Chevy Malibu Hybrid. On December 17, 2015 I took the car the Capital Cheverolet service dept who has been servicing my car regularly for the past five years. They performed a complete diagnostics on my car that determined I need to "replace the EBCM with brake pressure modulator valve" and said it would cost over $2800.00. Upon further research I discovered that the same make model and year was recalled under recall #39440. I also learned the my VIN number was not included in this recall. This is a safety defect that has rendered my car not drivable until I get it fixed. As a senior citizen on a fixed income I am unable to fixed. I would like to know why was my car not included in the recall and if its possible to get it on the recall list so it can be fixed.

The vehicle went into shift to park and will not turn off. This is a known problem with ALL GM vehicles that hasn’t been fixed or offered a warranty for. It’s dangerous and causes the car not to move shut off in traffic and drains the battery. My car currently isn’t working due to this issue and the repair to fix is too much with no assistance from GM for a known defect. My car was almost hit because of the car had to be towed because it’s unable to be moved.

My 2016 Malibu has a severe EBCM-related safety defect causing all four brakes to drag and overheat (reaching 240°F), leading to unstable handling. This condition mirrors the 2016 Malibu EBCM recall (GM Recall 39440). I sought help from GM. A GM-certified dealer-Monken in Centralia, IL performed a “diagnostic scan” which documented the core hydraulic failure: a constant, uncommanded 6.839 psi residual brake line pressure when the pedal was released. (A healthy system should be near 0 psi) This 6.839 psi is actively forcing the brakes to drag. The dealer ignored their own scientific data and submitted a fraudulent diagnosis of ("rust buildup") to GM, which GM used to deny the claim based on mileage. “Rust buildup” doesn’t create hydraulic pressure. GM is aware of this specific, documented, quantifiable safety defect (the 6.839 psi pressure) and is refusing to investigate it further. I stressed to GM that the vehicle wasn’t safe to drive and that I have a small child who has to ride in the car with me. GM dismissed my concerns by stating the dealership won’t release my car unless its safe to drive. I then had to drive the car 22 miles back home with all 4 brakes dragging. I requested the full diagnostic scan report (that the mechanic confirmed he could provide me with when I dropped my car off there) numerous times and never did I get one. I informed them that I would be filing a complaint hadn’t I received it by a certain time. The new kid in service then did send me screenshots of a generic OBDII scanner where I saw the 6.839 psi. I knew what the issue was prior to taking my car to Monken. I had an independent scan done prior. I only took the car there to comply with GM’s protocol to be eligible for assistance. I am requesting NHTSA investigate GM for failure to address a documented hydraulic control safety defect that causes brake dragging and overheating, which is non-compliant with safety standards. I can give further info Please call me for further details.

The contact owns a 2016 Chevrolet Malibu. The contact stated that after driving and parking the vehicle, the contact entered the residence; however, upon returning to the vehicle, the vehicle failed to start. There were no warning lights illuminated. The vehicle was towed to the local dealer, and the contact was informed that the battery needed to be replaced. The battery was replaced. The vehicle was diagnosed, and determined that the camshaft, fuel vacuum pump, and camshaft sensor needed to be replaced. The Oxygen sensors were replaced. The vehicle was not repaired. The manufacturer was not contacted. The failure mileage was approximately 146,000.