IllustrationIN A TURN AT HIGHER SPEEDS, THE STEERING WHEEL BECOMES STIFF, HARD TO TURN, AND THE BELL ALARM GOES OFF. *TR
2004 Chevrolet Malibu Maxx
Owner reports · Recalls · Investigations
Limited comparison data
There is not enough comparable history to draw a useful model-year comparison.
About this comparison →How this year compares
Owner complaints by model year
Compare all Malibu Maxx years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
570–25K
5425–50K
8050–75K
6175–100K
95100–150K
32150K+
379 reports with mileage · 55 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 251 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Seats. Review the 93 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 37 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
26 crash reports6 fire reports16 injury reports
What owners actually said
434 reportsTL*THE CONTACT OWNS A 2004 CHEVROLET MALIBU MAXX. THE DRIVERS SEAT FRAME THAT SUPPORTS THE SEAT WAS BROKEN SINCE 2008. THE VEHICLE WAS TAKEN TO THE DEALER WHO INFORMED HIM THAT IT WOULD COST HIM $1000 FOR REPAIRS. THE VEHICLE WAS NEVER REPAIRED. THE MANUFACTURER WAS NEVER NOTIFIED. THE VIN WAS UNKNOWN. THE FAILURE MILEAGE WAS 40…
Read full complaint
TL*THE CONTACT OWNS A 2004 CHEVROLET MALIBU MAXX. THE DRIVERS SEAT FRAME THAT SUPPORTS THE SEAT WAS BROKEN SINCE 2008. THE VEHICLE WAS TAKEN TO THE DEALER WHO INFORMED HIM THAT IT WOULD COST HIM $1000 FOR REPAIRS. THE VEHICLE WAS NEVER REPAIRED. THE MANUFACTURER WAS NEVER NOTIFIED. THE VIN WAS UNKNOWN. THE FAILURE MILEAGE WAS 40,000 AND THE CURRENT MILEAGE WAS 100,000.
I OWN A 2004 CHEVROLET MALIBU MAXX. THE POWER STEERING IN THE VEHICLE GOES OUT WHILE THE CAR IS IN MOTION. WHEN POWER STEERING GOES OUT, I HAVE TO STOP THE VEHICLE WHERE I AM AND TURN THE CAR OFF AND RESTART THE VEHICLE TO GET POWER STEERING TO COME BACK ON. ALSO THE LEFT TURN SIGNAL LIGHT CONTINUES TO GO OUT. I HAVE REPLACED TH…
Read full complaint
I OWN A 2004 CHEVROLET MALIBU MAXX. THE POWER STEERING IN THE VEHICLE GOES OUT WHILE THE CAR IS IN MOTION. WHEN POWER STEERING GOES OUT, I HAVE TO STOP THE VEHICLE WHERE I AM AND TURN THE CAR OFF AND RESTART THE VEHICLE TO GET POWER STEERING TO COME BACK ON. ALSO THE LEFT TURN SIGNAL LIGHT CONTINUES TO GO OUT. I HAVE REPLACED THE LIGHT SEVERAL TIMES AND IT CONTINUES TO BLOW AFTER A DAY. THE TURN SIGNAL BEING OUT MAKES IT HARD FOR ME TO TURN WHEN AT STOP SIGNS. OTHER DRIVERS DON'T KNOW I AM TURNING AND TRY TO DRIVE WHILE I AM MAKING A TURN. *TR
STEERING COLUMN FAILURE, LACK OF CONTROL OVER VEHICLE. *TR
DATE: 11/15/10. 2004 MALIBU MAXX LT. WHILE EXITING A LIMITED ACCESS HIGHWAY AT 25 MPH, THE DRIVER'S SEAT SUDDENLY DROPPED TWO OR THREE INCHES DOWN AND TO THE RIGHT, NEARLY CAUSING THE OPERATOR TO CRASH INTO THE SAFETY BARRIER. ONCE THE VEHICLE WAS STOPPED, AN INSPECTION REVEALED THE SEAT FRAME WELD HAD SEPARATED. RESEARCH SHOWS …
Read full complaint
DATE: 11/15/10. 2004 MALIBU MAXX LT. WHILE EXITING A LIMITED ACCESS HIGHWAY AT 25 MPH, THE DRIVER'S SEAT SUDDENLY DROPPED TWO OR THREE INCHES DOWN AND TO THE RIGHT, NEARLY CAUSING THE OPERATOR TO CRASH INTO THE SAFETY BARRIER. ONCE THE VEHICLE WAS STOPPED, AN INSPECTION REVEALED THE SEAT FRAME WELD HAD SEPARATED. RESEARCH SHOWS THIS IS A PROBLEM THAT HAS BEEN REPORTED TO THE NHTSA ON A NUMBER OF OCCASIONS WITHOUT CORRECTIVE ACTION. THE DEALER HAS INSPECTED THE DAMAGE AND CLAIMS THIS IS A RECURRING ISSUE. REPAIR IS OVER $1,000. THE RESULTING LITIGATION WILL RUN IN THE 10'S OF MILLIONS AS THE DEALERSHIP NOTES THAT IN A COLLISION THE SEAT MAY NOT STAY ANCHORED. THE SAFETY RESTRAINT IS ALSO ATTACHED TO THE SEAT, SO IT WILL BE INEFFECTIVE AS WELL. INVESTIGATE AND ISSUE THE RECALL! *TR
I NOTICED THE DRIVER SEAT WAS "ROCKING" TO THE RIGHT WHEN I SAT DOWN. WHEN I LOOKED UNDER THE SEAT I NOTICED THAT THE CROSSBAR WAS BROKEN AT THE WELD JOINT ON THE RIGHT SIDE OF THE SEAT. *TR
2004 CHEVY MALIBU MAXX WILL NOT START DUE TO PASSLOCK. CAR CRANKS OVER AND OFTEN TAKES A WHILE TO START. EVENTUALLY CAR STARTS. OFTEN LEFT STRANDED WAITING FOR IT TO START. *TR
LOSS OF POWER STEERING. WAS LEAVING A PARKING LOT AND PULLING OUT ONTO STREET WHEN POWER STEERING STOPPED WORKING. STEERING WHEEL THEN ABRUPTLY FELT SEIZED FOR A MOMENT CAUSING ME TO GO STRAIGHT INTO OPPOSITE LANE. THEN WAS ABLE TO REGAIN CONTROL HOWEVER STEERING WITH GREAT DIFFICULTY TO NEAREST DEALER. WHEN AT DEALER ASKED ABOU…
Read full complaint
LOSS OF POWER STEERING. WAS LEAVING A PARKING LOT AND PULLING OUT ONTO STREET WHEN POWER STEERING STOPPED WORKING. STEERING WHEEL THEN ABRUPTLY FELT SEIZED FOR A MOMENT CAUSING ME TO GO STRAIGHT INTO OPPOSITE LANE. THEN WAS ABLE TO REGAIN CONTROL HOWEVER STEERING WITH GREAT DIFFICULTY TO NEAREST DEALER. WHEN AT DEALER ASKED ABOUT RECALL OR BULLETIN. DEALER SAID THERE WAS NONE, HOWEVER THEY OFFERED A FIFTY /FIFTY SPLIT TO REPAIR. STRANGE IF THEY DIDN'T THINK IT WAS A DEFECT. REFUSED SERVICE AND CONTACTED MANUFACTURE, THEY SAID MY VEHICLE DIDN'T QUALIFY FOR "SPECIAL RECALL" . MY CAR WAS AN 04 "SPECIAL RECALL" IS FOR 05, I ASKED FOR AN EXCEPTION STATING THAT IT IS THE SAME PART, THEY REFUSED. ONE MONTH LATER MY CAR IS TOTALED AND IT NO LONGER HAS POWER STEERING. *TR
FRONT WELD OF THE DRIVER SEAT BROKE, CAUSING THE SEAT TO SOMETIMES LEAN TOWARDS THE FRONT RIGHT. WE TOOK IT TO CHEVY, ASKED THEM TO CHECK THE SEAT AND DO A STATE INSPECTION. THEY SAID THAT THEY DIDN'T KNOW WHAT IT WAS AND HAD TO PULL THE SEAT OUT. THEY THEN TOLD ME THAT IT WOULD BE $1,000 TO REPAIR THE SEAT, THEN TOLD ME IT W…
Read full complaint
FRONT WELD OF THE DRIVER SEAT BROKE, CAUSING THE SEAT TO SOMETIMES LEAN TOWARDS THE FRONT RIGHT. WE TOOK IT TO CHEVY, ASKED THEM TO CHECK THE SEAT AND DO A STATE INSPECTION. THEY SAID THAT THEY DIDN'T KNOW WHAT IT WAS AND HAD TO PULL THE SEAT OUT. THEY THEN TOLD ME THAT IT WOULD BE $1,000 TO REPAIR THE SEAT, THEN TOLD ME IT WOULD NOT PASS INSPECTION WITHOUT REPAIRING THE SEAT. WHEN I PICKED UP THE CAR, MORE WELDS HAD BROKEN AND THE SEAT WOBBLED A LOT. THEY TOLD ME THAT IF I PUT THE SEAT IN THE TOTALLY DOWN POSITION THAT IT WOULD NOT WOBBLE. WE COMPLAINED TO THE MANAGER, AND HE HAS AGREED TO CALL GM TO SEE ABOUT GETTING AN ALLOWANCE TO GET IT REPAIRED. NOW I AM LOOKING ONLINE AND SEE THAT THERE ARE A LOT OF COMPLAINTS ABOUT BROKEN WELDS ON THE SEAT. I HOPE THAT THERE WILL BE AN INVESTIGATION INTO THIS ISSUE. *TR
MY 2004 CHEVORLET MALIBU MAXX HAS HAD REPEATED FAILURE OF THE ELECTRONIC POWER STEERING. THE POWER STEERING HAS FAILED AT BOTH LOW AND HIGH RATES OF SPEED. THE POWER STEERING ASSIST GOES OUT AND MAKES THE VEHICLE NEARLY IMPOSSIBLE TO STEER. *TR
Official recalls
314V252000 · Electrical System:wiring; Electronic Stability Control (esc); Exterior Lighting:brake Lights; Exterior Lighting:brake Lights:switch; Vehicle Speed Control:cruise Control
May 14, 2014
General Motors LLC (GM) is recalling certain model year 2004-2012 Chevrolet Malibu vehicles manufactured May 16, 2003, through October 11, 2012, 2004-2007 Malibu Maxx vehicles manufactured June 25, 2003, through April 5, 2007, 2005-2010 Pontiac G6 vehicles manufactured May 26, 2004, through January 4, 2010, and 2007-2010 Saturn Aura vehicles manufactured April 24, 2006, through May 26, 2009. In the affected vehicles, increased resistance in the Body Control Module (BCM) connection may result in voltage fluctuations in the Brake Apply Sensor (BAS) circuit. These fluctuations can cause one or more of these conditions: the brake lights to illuminate without the brake pedal being pushed; the brake lights to not illuminate when the pedal is pushed; difficulty disengaging the cruise control; moving the gear shifter out of the 'PARK' position without pushing the brake; and disablement of crash avoidance features such as traction control, electronic stability control, and panic braking assist features.
Consequence & remedy
Consequence: Any of the above failure conditions increases the risk of a crash.
Remedy: GM will notify owners, and dealers will attach the wiring harness to the BCM with a spacer, apply dielectric lubricant to both the BCM and harness connector and the BAS and harness connector, and will relearn the brake pedal home position, free of charge. The manufacturer distributed an Interim letter to customers on July 14, 2014. The recall began on August 18, 2014. Owners may contact General Motors customer service at 1-800-222-1020 (Chevrolet), 1-800-762-2737 (Pontiac), 1-800-553-6000 (Saturn). GM's number for this recall is 13036.
Additional source detail variants (5)
Electronic Stability Control (esc)
General Motors LLC (GM) is recalling certain model year 2004-2012 Chevrolet Malibu vehicles manufactured May 16, 2003, through October 11, 2012, 2004-2007 Malibu Maxx vehicles manufactured June 25, 2003, through April 5, 2007, 2005-2010 Pontiac G6 vehicles manufactured May 26, 2004, through January 4, 2010, and 2007-2010 Saturn Aura vehicles manufactured April 24, 2006, through May 26, 2009. In the affected vehicles, increased resistance in the Body Control Module (BCM) connection may result in voltage fluctuations in the Brake Apply Sensor (BAS) circuit. These fluctuations can cause one or more of these conditions: the brake lights to illuminate without the brake pedal being pushed; the brake lights to not illuminate when the pedal is pushed; difficulty disengaging the cruise control; moving the gear shifter out of the 'PARK' position without pushing the brake; and disablement of crash avoidance features such as traction control, electronic stability control, and panic braking assist features.
Consequence: Any of the above failure conditions increases the risk of a crash.
Remedy: GM will notify owners, and dealers will attach the wiring harness to the BCM with a spacer, apply dielectric lubricant to both the BCM and harness connector and the BAS and harness connector, and will relearn the brake pedal home position, free of charge. The manufacturer distributed an Interim letter to customers on July 14, 2014. The recall began on August 18, 2014. Owners may contact General Motors customer service at 1-800-222-1020 (Chevrolet), 1-800-762-2737 (Pontiac), 1-800-553-6000 (Saturn). GM's number for this recall is 13036.
Vehicle Speed Control:cruise Control
General Motors LLC (GM) is recalling certain model year 2004-2012 Chevrolet Malibu vehicles manufactured May 16, 2003, through October 11, 2012, 2004-2007 Malibu Maxx vehicles manufactured June 25, 2003, through April 5, 2007, 2005-2010 Pontiac G6 vehicles manufactured May 26, 2004, through January 4, 2010, and 2007-2010 Saturn Aura vehicles manufactured April 24, 2006, through May 26, 2009. In the affected vehicles, increased resistance in the Body Control Module (BCM) connection may result in voltage fluctuations in the Brake Apply Sensor (BAS) circuit. These fluctuations can cause one or more of these conditions: the brake lights to illuminate without the brake pedal being pushed; the brake lights to not illuminate when the pedal is pushed; difficulty disengaging the cruise control; moving the gear shifter out of the 'PARK' position without pushing the brake; and disablement of crash avoidance features such as traction control, electronic stability control, and panic braking assist features.
Consequence: Any of the above failure conditions increases the risk of a crash.
Remedy: GM will notify owners, and dealers will attach the wiring harness to the BCM with a spacer, apply dielectric lubricant to both the BCM and harness connector and the BAS and harness connector, and will relearn the brake pedal home position, free of charge. The manufacturer distributed an Interim letter to customers on July 14, 2014. The recall began on August 18, 2014. Owners may contact General Motors customer service at 1-800-222-1020 (Chevrolet), 1-800-762-2737 (Pontiac), 1-800-553-6000 (Saturn). GM's number for this recall is 13036.
Exterior Lighting:brake Lights:switch
General Motors LLC (GM) is recalling certain model year 2004-2012 Chevrolet Malibu vehicles manufactured May 16, 2003, through October 11, 2012, 2004-2007 Malibu Maxx vehicles manufactured June 25, 2003, through April 5, 2007, 2005-2010 Pontiac G6 vehicles manufactured May 26, 2004, through January 4, 2010, and 2007-2010 Saturn Aura vehicles manufactured April 24, 2006, through May 26, 2009. In the affected vehicles, increased resistance in the Body Control Module (BCM) connection may result in voltage fluctuations in the Brake Apply Sensor (BAS) circuit. These fluctuations can cause one or more of these conditions: the brake lights to illuminate without the brake pedal being pushed; the brake lights to not illuminate when the pedal is pushed; difficulty disengaging the cruise control; moving the gear shifter out of the 'PARK' position without pushing the brake; and disablement of crash avoidance features such as traction control, electronic stability control, and panic braking assist features.
Consequence: Any of the above failure conditions increases the risk of a crash.
Remedy: GM will notify owners, and dealers will attach the wiring harness to the BCM with a spacer, apply dielectric lubricant to both the BCM and harness connector and the BAS and harness connector, and will relearn the brake pedal home position, free of charge. The manufacturer distributed an Interim letter to customers on July 14, 2014. The recall began on August 18, 2014. Owners may contact General Motors customer service at 1-800-222-1020 (Chevrolet), 1-800-762-2737 (Pontiac), 1-800-553-6000 (Saturn). GM's number for this recall is 13036.
Exterior Lighting:brake Lights
General Motors LLC (GM) is recalling certain model year 2004-2012 Chevrolet Malibu vehicles manufactured May 16, 2003, through October 11, 2012, 2004-2007 Malibu Maxx vehicles manufactured June 25, 2003, through April 5, 2007, 2005-2010 Pontiac G6 vehicles manufactured May 26, 2004, through January 4, 2010, and 2007-2010 Saturn Aura vehicles manufactured April 24, 2006, through May 26, 2009. In the affected vehicles, increased resistance in the Body Control Module (BCM) connection may result in voltage fluctuations in the Brake Apply Sensor (BAS) circuit. These fluctuations can cause one or more of these conditions: the brake lights to illuminate without the brake pedal being pushed; the brake lights to not illuminate when the pedal is pushed; difficulty disengaging the cruise control; moving the gear shifter out of the 'PARK' position without pushing the brake; and disablement of crash avoidance features such as traction control, electronic stability control, and panic braking assist features.
Consequence: Any of the above failure conditions increases the risk of a crash.
Remedy: GM will notify owners, and dealers will attach the wiring harness to the BCM with a spacer, apply dielectric lubricant to both the BCM and harness connector and the BAS and harness connector, and will relearn the brake pedal home position, free of charge. The manufacturer distributed an Interim letter to customers on July 14, 2014. The recall began on August 18, 2014. Owners may contact General Motors customer service at 1-800-222-1020 (Chevrolet), 1-800-762-2737 (Pontiac), 1-800-553-6000 (Saturn). GM's number for this recall is 13036.
Electrical System:wiring
General Motors LLC (GM) is recalling certain model year 2004-2012 Chevrolet Malibu vehicles manufactured May 16, 2003, through October 11, 2012, 2004-2007 Malibu Maxx vehicles manufactured June 25, 2003, through April 5, 2007, 2005-2010 Pontiac G6 vehicles manufactured May 26, 2004, through January 4, 2010, and 2007-2010 Saturn Aura vehicles manufactured April 24, 2006, through May 26, 2009. In the affected vehicles, increased resistance in the Body Control Module (BCM) connection may result in voltage fluctuations in the Brake Apply Sensor (BAS) circuit. These fluctuations can cause one or more of these conditions: the brake lights to illuminate without the brake pedal being pushed; the brake lights to not illuminate when the pedal is pushed; difficulty disengaging the cruise control; moving the gear shifter out of the 'PARK' position without pushing the brake; and disablement of crash avoidance features such as traction control, electronic stability control, and panic braking assist features.
Consequence: Any of the above failure conditions increases the risk of a crash.
Remedy: GM will notify owners, and dealers will attach the wiring harness to the BCM with a spacer, apply dielectric lubricant to both the BCM and harness connector and the BAS and harness connector, and will relearn the brake pedal home position, free of charge. The manufacturer distributed an Interim letter to customers on July 14, 2014. The recall began on August 18, 2014. Owners may contact General Motors customer service at 1-800-222-1020 (Chevrolet), 1-800-762-2737 (Pontiac), 1-800-553-6000 (Saturn). GM's number for this recall is 13036.
14V224000 · Power Train:automatic Transmission; Power Train:automatic Transmission:lever And Linkage:floor Shift
Apr 30, 2014
General Motors LLC (GM) notified the agency on April 29, 2014, that they are recalling 56,214 model year 2007 and 2008 Saturn Aura vehicles. On May 22, 2014, GM increased the recall to include an additional 1,074,899 model year 2004-2008 Chevrolet Malibu vehicles manufactured from May 16, 2003, through October 5, 2007, model year 2004-2007 Malibu Maxx vehicles manufactured from June 25, 2003, through April 5, 2007, and model year 2005-2008 Pontiac G6 vehicles manufactured from May 26, 2004, through September 28, 2007, and equipped with 4-speed transmissions. The total number vehicles being recalled is now 1,131,113.
Consequence & remedy
Consequence: If the transmission shift cable fractures while the vehicle is being driven, the transmission gear selection may not match the indicated gear and the vehicle may move in an unintended or unexpected direction, increasing the risk of a crash. Furthermore, when the driver goes to stop and park the vehicle, despite selecting the PARK position, the transmission may not be in PARK. If the vehicle is not in the "PARK" position there is a risk the vehicle will roll away as the driver and other occupants exit the vehicle or anytime thereafter. A vehicle rollaway increases the risk of injury to exiting occupants and bystanders.
Remedy: GM will notify owners, and GM dealers will replace the shift cable assembly and mounting bracket, free of charge. The manufacturer has not yet provided a notification schedule. Owners may contact General Motors at 1-800-553-6000. GM's number for this recall is 14152.
Additional source detail variants (2)
Power Train:automatic Transmission:lever And Linkage:floor Shift
General Motors LLC (GM) notified the agency on April 29, 2014, that they are recalling 56,214 model year 2007 and 2008 Saturn Aura vehicles. On May 22, 2014, GM increased the recall to include an additional 1,074,899 model year 2004-2008 Chevrolet Malibu vehicles manufactured from May 16, 2003, through October 5, 2007, model year 2004-2007 Malibu Maxx vehicles manufactured from June 25, 2003, through April 5, 2007, and model year 2005-2008 Pontiac G6 vehicles manufactured from May 26, 2004, through September 28, 2007, and equipped with 4-speed transmissions. The total number vehicles being recalled is now 1,131,113.
Consequence: If the transmission shift cable fractures while the vehicle is being driven, the transmission gear selection may not match the indicated gear and the vehicle may move in an unintended or unexpected direction, increasing the risk of a crash. Furthermore, when the driver goes to stop and park the vehicle, despite selecting the PARK position, the transmission may not be in PARK. If the vehicle is not in the "PARK" position there is a risk the vehicle will roll away as the driver and other occupants exit the vehicle or anytime thereafter. A vehicle rollaway increases the risk of injury to exiting occupants and bystanders.
Remedy: GM will notify owners, and GM dealers will replace the shift cable assembly and mounting bracket, free of charge. The manufacturer has not yet provided a notification schedule. Owners may contact General Motors at 1-800-553-6000. GM's number for this recall is 14152.
Power Train:automatic Transmission
General Motors LLC (GM) notified the agency on April 29, 2014, that they are recalling 56,214 model year 2007 and 2008 Saturn Aura vehicles. On May 22, 2014, GM increased the recall to include an additional 1,074,899 model year 2004-2008 Chevrolet Malibu vehicles manufactured from May 16, 2003, through October 5, 2007, model year 2004-2007 Malibu Maxx vehicles manufactured from June 25, 2003, through April 5, 2007, and model year 2005-2008 Pontiac G6 vehicles manufactured from May 26, 2004, through September 28, 2007, and equipped with 4-speed transmissions. The total number vehicles being recalled is now 1,131,113.
Consequence: If the transmission shift cable fractures while the vehicle is being driven, the transmission gear selection may not match the indicated gear and the vehicle may move in an unintended or unexpected direction, increasing the risk of a crash. Furthermore, when the driver goes to stop and park the vehicle, despite selecting the PARK position, the transmission may not be in PARK. If the vehicle is not in the "PARK" position there is a risk the vehicle will roll away as the driver and other occupants exit the vehicle or anytime thereafter. A vehicle rollaway increases the risk of injury to exiting occupants and bystanders.
Remedy: GM will notify owners, and GM dealers will replace the shift cable assembly and mounting bracket, free of charge. The manufacturer has not yet provided a notification schedule. Owners may contact General Motors at 1-800-553-6000. GM's number for this recall is 14152.
14V153000 · Steering:electric Power Assist System
Mar 31, 2014
General Motors LLC (GM) is recalling certain model year 2004-2006 and 2008-2009 Chevrolet Malibu, 2004-2006 Malibu Maxx, 2009-2010 HHR (non-turbo), 2010 Cobalt, 2008-2009 Saturn Aura and 2004-2007 Ion, and 2005-2009 Pontiac G6. In the affected vehicles, there may be a sudden loss of electric power steering (EPS) assist that could occur at any time while driving.
Consequence & remedy
Consequence: If power steering assist is lost, greater driver effort would be required to steer the vehicle at low speeds, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will perform one of four bulletins. Parts are not currently available. GM expects to send an interim notification around May 28, 2014. When parts are available, owners will be mailed a second letter to come in to have the applicable bulletin applied. Bulletin 14115 covers model year 2004-2007 Saturn Ion, 2009-2010 Chevrolet HHR and 2010 Chevrolet Cobalts. Dealers will replace the EPS motor. Bulletin 14116 covers model year 2004-2006 Chevrolet Malibu and Malibu Maxx, 2005-2006 Pontiac G6 and 2008-2009 Chevrolet Malibu, Pontiac G6 and Saturn Aura built from March 1, 2008, through June 27, 2008. Dealers will replace the torque sensor assembly. Bulletin 14117 covers model year 2008 Chevrolet Malibu, Pontiac G6 and Saturn Aura built from February 1, 2008, through February 28, 2008. Dealers will replace the torque sensor assembly and EPS motor controller unit. Bulletin 14118 covers model year 2008 Chevrolet Malibu, Pontiac G6 and Saturn Aura built from October 1, 2007, through January 31, 2008. Dealers will replace the EPS motor controller unit. The recall began on July 17, 2014. Owners may contact Chevrolet at 1-800-630-2438, Saturn at 1-800-553-6000, and Pontiac at 1-800-620-7668. GM's number for this recall is N140115. Note: GM bulletin number 14119 will be implemented for model year 2006-2008 and early production of 2009 Chevrolet HHR (non-turbo) and model year 2003 Saturn ION to provide EPS Motor replacement for the life of the vehicle.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
4EA09004 · Turn Signal Lamps
Opened Mar 20, 2009 · Closed Aug 12, 2010
Status: closed (inferred from source dates) · Exterior Lighting:brake Lights; Exterior Lighting:headlights; Exterior Lighting:tail Lights; Exterior Lighting:turn Signal
GM designed the MY 2004 and 2005 Chevrolet Malibu and Malibu Maxx vehicles with a daytime running lamp (DRL) system that uses the same filament (the high power filament of a dual filament bulb) as the front turn signals.The high power filament operates at full battery voltage when functioning as a DRL.The DRL is illuminated whenever the headlamps are off, increasing the duty cycle of the front turn signal bulb.The MY 2003 and earlier Malibu vehicles (Malibu Maxx was not manufactured for sale in the U.S. prior to MY 2004) used a headlamp based design, operated at a reduced voltage, for the DRL function; GM reverted back to this design on the MY 2006 and later Malibu and Malibu Maxx vehicles. Filament based bulbs have a finite life (hours of illumination) for any given operating voltage.As a result, increasing the duty cycle of a bulb typically decreases the life span of the bulb.GM identified and addressed two front turn signal/DRL and rear turn signal bulb quality issues early in MY 2004 production, however vehicle warranty claims for failed bulbs continued to occur.To address the high warranty levels of bulb failures (90% of the warranty claims submitted to ODI by GM were bulb failures and 10% were socket failures), GM issued a technical service bulletin in March 2006 advising dealers to use a new specification of bulb when addressing service failures, and to also inspect the electrical sockets for thermal damage and replace if necessary.In June 2006 (after subject vehicle production ended) GM changed the turn signal bulb specification to that of the TSB bulb in vehicle production also.To date, ODI has not identified any allegations of crash, injury, or fire related to the alleged defect even though the subject vehicles have experienced 5 - 6 years of field exposure.ODI's analysis of consumer complaints, both VOQ and manufacturer, shows a declining trend.The warranty rate for turn signal bulb replacement is high however statistical analysis of the warranty data suggests that the majority of the original equipment bulbs have already been replaced.GM conducted a safety recall (06V-263) for MY 2004-2005 Cadillac XLR to replace the front turn signal/DRL bulbs and the electrical sockets.However GM advised that the turn signal/DRL bulbs/sockets on the subject vehicles differ from those on the recalled XLRs in several respects, including using bulb sockets with four electrical terminals as opposed to three, which improves the electrical connection, allows the bulb to operate at a lower temperature, and adds stability to the bulb in the socket; operating at a lower voltage, which increases vehicle bulb life; using vented headlamps, which allows bulbs to run cooler than those installed in a non-vented XLR headlamp; and using a clear bulb, which runs cooler than the amber bulbs installed on the XLR.Additionally, the warranty claim level related to subject vehicle sockets is unremarkable compared to other defect investigations into defective socket assemblies.A safety-related defect trend has not been identified at this time.Further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will take further action if warranted by the circumstances.See attached report for further information.
Additional source detail variants (4)
Exterior Lighting:brake Lights
GM designed the MY 2004 and 2005 Chevrolet Malibu and Malibu Maxx vehicles with a daytime running lamp (DRL) system that uses the same filament (the high power filament of a dual filament bulb) as the front turn signals.The high power filament operates at full battery voltage when functioning as a DRL.The DRL is illuminated whenever the headlamps are off, increasing the duty cycle of the front turn signal bulb.The MY 2003 and earlier Malibu vehicles (Malibu Maxx was not manufactured for sale in the U.S. prior to MY 2004) used a headlamp based design, operated at a reduced voltage, for the DRL function; GM reverted back to this design on the MY 2006 and later Malibu and Malibu Maxx vehicles. Filament based bulbs have a finite life (hours of illumination) for any given operating voltage.As a result, increasing the duty cycle of a bulb typically decreases the life span of the bulb.GM identified and addressed two front turn signal/DRL and rear turn signal bulb quality issues early in MY 2004 production, however vehicle warranty claims for failed bulbs continued to occur.To address the high warranty levels of bulb failures (90% of the warranty claims submitted to ODI by GM were bulb failures and 10% were socket failures), GM issued a technical service bulletin in March 2006 advising dealers to use a new specification of bulb when addressing service failures, and to also inspect the electrical sockets for thermal damage and replace if necessary.In June 2006 (after subject vehicle production ended) GM changed the turn signal bulb specification to that of the TSB bulb in vehicle production also.To date, ODI has not identified any allegations of crash, injury, or fire related to the alleged defect even though the subject vehicles have experienced 5 - 6 years of field exposure.ODI's analysis of consumer complaints, both VOQ and manufacturer, shows a declining trend.The warranty rate for turn signal bulb replacement is high however statistical analysis of the warranty data suggests that the majority of the original equipment bulbs have already been replaced.GM conducted a safety recall (06V-263) for MY 2004-2005 Cadillac XLR to replace the front turn signal/DRL bulbs and the electrical sockets.However GM advised that the turn signal/DRL bulbs/sockets on the subject vehicles differ from those on the recalled XLRs in several respects, including using bulb sockets with four electrical terminals as opposed to three, which improves the electrical connection, allows the bulb to operate at a lower temperature, and adds stability to the bulb in the socket; operating at a lower voltage, which increases vehicle bulb life; using vented headlamps, which allows bulbs to run cooler than those installed in a non-vented XLR headlamp; and using a clear bulb, which runs cooler than the amber bulbs installed on the XLR.Additionally, the warranty claim level related to subject vehicle sockets is unremarkable compared to other defect investigations into defective socket assemblies.A safety-related defect trend has not been identified at this time.Further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will take further action if warranted by the circumstances.See attached report for further information.
Exterior Lighting:headlights
GM designed the MY 2004 and 2005 Chevrolet Malibu and Malibu Maxx vehicles with a daytime running lamp (DRL) system that uses the same filament (the high power filament of a dual filament bulb) as the front turn signals.The high power filament operates at full battery voltage when functioning as a DRL.The DRL is illuminated whenever the headlamps are off, increasing the duty cycle of the front turn signal bulb.The MY 2003 and earlier Malibu vehicles (Malibu Maxx was not manufactured for sale in the U.S. prior to MY 2004) used a headlamp based design, operated at a reduced voltage, for the DRL function; GM reverted back to this design on the MY 2006 and later Malibu and Malibu Maxx vehicles. Filament based bulbs have a finite life (hours of illumination) for any given operating voltage.As a result, increasing the duty cycle of a bulb typically decreases the life span of the bulb.GM identified and addressed two front turn signal/DRL and rear turn signal bulb quality issues early in MY 2004 production, however vehicle warranty claims for failed bulbs continued to occur.To address the high warranty levels of bulb failures (90% of the warranty claims submitted to ODI by GM were bulb failures and 10% were socket failures), GM issued a technical service bulletin in March 2006 advising dealers to use a new specification of bulb when addressing service failures, and to also inspect the electrical sockets for thermal damage and replace if necessary.In June 2006 (after subject vehicle production ended) GM changed the turn signal bulb specification to that of the TSB bulb in vehicle production also.To date, ODI has not identified any allegations of crash, injury, or fire related to the alleged defect even though the subject vehicles have experienced 5 - 6 years of field exposure.ODI's analysis of consumer complaints, both VOQ and manufacturer, shows a declining trend.The warranty rate for turn signal bulb replacement is high however statistical analysis of the warranty data suggests that the majority of the original equipment bulbs have already been replaced.GM conducted a safety recall (06V-263) for MY 2004-2005 Cadillac XLR to replace the front turn signal/DRL bulbs and the electrical sockets.However GM advised that the turn signal/DRL bulbs/sockets on the subject vehicles differ from those on the recalled XLRs in several respects, including using bulb sockets with four electrical terminals as opposed to three, which improves the electrical connection, allows the bulb to operate at a lower temperature, and adds stability to the bulb in the socket; operating at a lower voltage, which increases vehicle bulb life; using vented headlamps, which allows bulbs to run cooler than those installed in a non-vented XLR headlamp; and using a clear bulb, which runs cooler than the amber bulbs installed on the XLR.Additionally, the warranty claim level related to subject vehicle sockets is unremarkable compared to other defect investigations into defective socket assemblies.A safety-related defect trend has not been identified at this time.Further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will take further action if warranted by the circumstances.See attached report for further information.
Exterior Lighting:tail Lights
GM designed the MY 2004 and 2005 Chevrolet Malibu and Malibu Maxx vehicles with a daytime running lamp (DRL) system that uses the same filament (the high power filament of a dual filament bulb) as the front turn signals.The high power filament operates at full battery voltage when functioning as a DRL.The DRL is illuminated whenever the headlamps are off, increasing the duty cycle of the front turn signal bulb.The MY 2003 and earlier Malibu vehicles (Malibu Maxx was not manufactured for sale in the U.S. prior to MY 2004) used a headlamp based design, operated at a reduced voltage, for the DRL function; GM reverted back to this design on the MY 2006 and later Malibu and Malibu Maxx vehicles. Filament based bulbs have a finite life (hours of illumination) for any given operating voltage.As a result, increasing the duty cycle of a bulb typically decreases the life span of the bulb.GM identified and addressed two front turn signal/DRL and rear turn signal bulb quality issues early in MY 2004 production, however vehicle warranty claims for failed bulbs continued to occur.To address the high warranty levels of bulb failures (90% of the warranty claims submitted to ODI by GM were bulb failures and 10% were socket failures), GM issued a technical service bulletin in March 2006 advising dealers to use a new specification of bulb when addressing service failures, and to also inspect the electrical sockets for thermal damage and replace if necessary.In June 2006 (after subject vehicle production ended) GM changed the turn signal bulb specification to that of the TSB bulb in vehicle production also.To date, ODI has not identified any allegations of crash, injury, or fire related to the alleged defect even though the subject vehicles have experienced 5 - 6 years of field exposure.ODI's analysis of consumer complaints, both VOQ and manufacturer, shows a declining trend.The warranty rate for turn signal bulb replacement is high however statistical analysis of the warranty data suggests that the majority of the original equipment bulbs have already been replaced.GM conducted a safety recall (06V-263) for MY 2004-2005 Cadillac XLR to replace the front turn signal/DRL bulbs and the electrical sockets.However GM advised that the turn signal/DRL bulbs/sockets on the subject vehicles differ from those on the recalled XLRs in several respects, including using bulb sockets with four electrical terminals as opposed to three, which improves the electrical connection, allows the bulb to operate at a lower temperature, and adds stability to the bulb in the socket; operating at a lower voltage, which increases vehicle bulb life; using vented headlamps, which allows bulbs to run cooler than those installed in a non-vented XLR headlamp; and using a clear bulb, which runs cooler than the amber bulbs installed on the XLR.Additionally, the warranty claim level related to subject vehicle sockets is unremarkable compared to other defect investigations into defective socket assemblies.A safety-related defect trend has not been identified at this time.Further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will take further action if warranted by the circumstances.See attached report for further information.
Exterior Lighting:turn Signal
GM designed the MY 2004 and 2005 Chevrolet Malibu and Malibu Maxx vehicles with a daytime running lamp (DRL) system that uses the same filament (the high power filament of a dual filament bulb) as the front turn signals.The high power filament operates at full battery voltage when functioning as a DRL.The DRL is illuminated whenever the headlamps are off, increasing the duty cycle of the front turn signal bulb.The MY 2003 and earlier Malibu vehicles (Malibu Maxx was not manufactured for sale in the U.S. prior to MY 2004) used a headlamp based design, operated at a reduced voltage, for the DRL function; GM reverted back to this design on the MY 2006 and later Malibu and Malibu Maxx vehicles. Filament based bulbs have a finite life (hours of illumination) for any given operating voltage.As a result, increasing the duty cycle of a bulb typically decreases the life span of the bulb.GM identified and addressed two front turn signal/DRL and rear turn signal bulb quality issues early in MY 2004 production, however vehicle warranty claims for failed bulbs continued to occur.To address the high warranty levels of bulb failures (90% of the warranty claims submitted to ODI by GM were bulb failures and 10% were socket failures), GM issued a technical service bulletin in March 2006 advising dealers to use a new specification of bulb when addressing service failures, and to also inspect the electrical sockets for thermal damage and replace if necessary.In June 2006 (after subject vehicle production ended) GM changed the turn signal bulb specification to that of the TSB bulb in vehicle production also.To date, ODI has not identified any allegations of crash, injury, or fire related to the alleged defect even though the subject vehicles have experienced 5 - 6 years of field exposure.ODI's analysis of consumer complaints, both VOQ and manufacturer, shows a declining trend.The warranty rate for turn signal bulb replacement is high however statistical analysis of the warranty data suggests that the majority of the original equipment bulbs have already been replaced.GM conducted a safety recall (06V-263) for MY 2004-2005 Cadillac XLR to replace the front turn signal/DRL bulbs and the electrical sockets.However GM advised that the turn signal/DRL bulbs/sockets on the subject vehicles differ from those on the recalled XLRs in several respects, including using bulb sockets with four electrical terminals as opposed to three, which improves the electrical connection, allows the bulb to operate at a lower temperature, and adds stability to the bulb in the socket; operating at a lower voltage, which increases vehicle bulb life; using vented headlamps, which allows bulbs to run cooler than those installed in a non-vented XLR headlamp; and using a clear bulb, which runs cooler than the amber bulbs installed on the XLR.Additionally, the warranty claim level related to subject vehicle sockets is unremarkable compared to other defect investigations into defective socket assemblies.A safety-related defect trend has not been identified at this time.Further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will take further action if warranted by the circumstances.See attached report for further information.
PE08062 · Turn Signal Lamps
Opened Oct 21, 2008 · Closed Mar 20, 2009
Status: closed (inferred from source dates) · Exterior Lighting:tail Lights; Exterior Lighting:turn Signal
THE SUBJECT VEHICLES MAY EXPERIENCE LOSS OF FUNCTION OF ONE OR MORE OF THE PARK, TURN, STOP OR DAYTIME RUNNING LAMPS (DRL).FAILURE OF THE BULB MAY ALSO INCLUDE DISCOLORATION (HEAT DAMAGE) TO THE BULB SOCKET.GENERAL MOTORS (GM) TECHNICAL SERVICE BULLETIN (TSB) NUMBER 06-08-42-004C INSTRUCTS TECHNICIANS TO EXAMINE THE LAMP HOUSING FOR SIGNS OF DISCOLORATION AND TO REPLACE THE BULBS AND OR SOCKETS DEPENDING ON THE SEVERITY OF THE DISCOLORATION AND THE CONDITION OF THE BULBS AND SOCKETS.THE SCOPE OF INVESTIGATION IN THE PRELIMINARY EVALUATION (PE08-062) WAS THE 2004 MALIBU/MAXX.HOWEVER, THE AGENCY EVALUATED GM'S WARRANTY DATA WHICH INDICATES THAT THE 2005 MODEL YEAR (MY) MALIBU AND MALIBU MAXX VEHICLES ARE ALSO AFFECTED BY THIS CONDITION.THIS INVESTIGATION IS UPGRADED TO AN ENGINEERING ANALYSIS (EA09-004).
Additional source detail variants (2)
Exterior Lighting:tail Lights
THE SUBJECT VEHICLES MAY EXPERIENCE LOSS OF FUNCTION OF ONE OR MORE OF THE PARK, TURN, STOP OR DAYTIME RUNNING LAMPS (DRL).FAILURE OF THE BULB MAY ALSO INCLUDE DISCOLORATION (HEAT DAMAGE) TO THE BULB SOCKET.GENERAL MOTORS (GM) TECHNICAL SERVICE BULLETIN (TSB) NUMBER 06-08-42-004C INSTRUCTS TECHNICIANS TO EXAMINE THE LAMP HOUSING FOR SIGNS OF DISCOLORATION AND TO REPLACE THE BULBS AND OR SOCKETS DEPENDING ON THE SEVERITY OF THE DISCOLORATION AND THE CONDITION OF THE BULBS AND SOCKETS.THE SCOPE OF INVESTIGATION IN THE PRELIMINARY EVALUATION (PE08-062) WAS THE 2004 MALIBU/MAXX.HOWEVER, THE AGENCY EVALUATED GM'S WARRANTY DATA WHICH INDICATES THAT THE 2005 MODEL YEAR (MY) MALIBU AND MALIBU MAXX VEHICLES ARE ALSO AFFECTED BY THIS CONDITION.THIS INVESTIGATION IS UPGRADED TO AN ENGINEERING ANALYSIS (EA09-004).
Exterior Lighting:turn Signal
THE SUBJECT VEHICLES MAY EXPERIENCE LOSS OF FUNCTION OF ONE OR MORE OF THE PARK, TURN, STOP OR DAYTIME RUNNING LAMPS (DRL).FAILURE OF THE BULB MAY ALSO INCLUDE DISCOLORATION (HEAT DAMAGE) TO THE BULB SOCKET.GENERAL MOTORS (GM) TECHNICAL SERVICE BULLETIN (TSB) NUMBER 06-08-42-004C INSTRUCTS TECHNICIANS TO EXAMINE THE LAMP HOUSING FOR SIGNS OF DISCOLORATION AND TO REPLACE THE BULBS AND OR SOCKETS DEPENDING ON THE SEVERITY OF THE DISCOLORATION AND THE CONDITION OF THE BULBS AND SOCKETS.THE SCOPE OF INVESTIGATION IN THE PRELIMINARY EVALUATION (PE08-062) WAS THE 2004 MALIBU/MAXX.HOWEVER, THE AGENCY EVALUATED GM'S WARRANTY DATA WHICH INDICATES THAT THE 2005 MODEL YEAR (MY) MALIBU AND MALIBU MAXX VEHICLES ARE ALSO AFFECTED BY THIS CONDITION.THIS INVESTIGATION IS UPGRADED TO AN ENGINEERING ANALYSIS (EA09-004).
EA04018 · Loss Of Electric Power Steering
Opened Jul 1, 2004 · Closed May 10, 2005
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System
IN PERFORMING THIS ENGINEERING ANALYSIS, ODI DETERMINED THAT THE ELECTRIC POWER STEERING SYSTEM IN THE SUBJECT VEHICLES CAN MALFUNCTION OR FAIL, CAUSING THE DRIVER TO LOSE POWER STEERING ASSISTANCE; HOWEVER, DUE TO THE FOLLOWING REASONS, ODI HAS DECIDED THAT FURTHER EXPENDITURE OF AGENCY RESOURCES ON THIS INVESTIGATION IS NOT WARRANTED AT THIS TIME: - GM ISSUED CUSTOMER SATISFACTION CAMPAIGN (CSC) 04050A INDECEMBER 2004 TO ADDRESS THE ALLEGED DEFECT IN APPROXIMATELY58,700 SUBJECT VEHICLES, ENCOMPASSING AT LEAST 97 PERCENT OF THECOMPLAINT AND WARRANTY CLAIMS POPULATION.VEHICLES OUTSIDE THECSC 04050A POPULATION CONTAIN A NEWLY DESIGNED TORQUE ANDPOSITION SENSOR AND HAVE EXPERIENCED A RELATIVELY LOW COMPLAINTRATE.THIS CUSTOMER SATISFACTION CAMPAIGN PRESENTLY HAS ACOMPLETION RATE OF 52%. - THE IMPACT ON THE DRIVER?S ABILITY TO CONTROL THESE RELATIVELYSMALL AND LIGHT VEHICLES WAS LIMITED.VRTC TEST ENGINEERS WEREUNABLE TO INDUCE A FAILURE MODE THAT WOULD CAUSE THE EPS TOSUBSTANTIALLY LIMIT THE DRIVER?S ABILITY TO TURN THE VEHICLE IN APARTICULAR DIRECTION OR TO PROVIDE THE DRIVER WITH UNINTENDEDPOWER ASSISTANCE.- THERE IS NO RISK OF FIRE.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT A SAFETY-RELATED DEFECT DOES NOT EXIST.THE AGENCY WILL CONTINUE TO MONITOR COMPLAINTS AND OTHER INFORMATION RELATING TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES AND TAKE FURTHER ACTION IN THE FUTURE IF WARRANTED BY THE CIRCUMSTANCES.(FOR FURTHER DETAILS SEE ATTACHED ENGINEERING ANALYSIS (EA04-018)CLOSING REPORT.)
Additional source detail variants (2)
Steering:electric Power Assist System
IN PERFORMING THIS ENGINEERING ANALYSIS, ODI DETERMINED THAT THE ELECTRIC POWER STEERING SYSTEM IN THE SUBJECT VEHICLES CAN MALFUNCTION OR FAIL, CAUSING THE DRIVER TO LOSE POWER STEERING ASSISTANCE; HOWEVER, DUE TO THE FOLLOWING REASONS, ODI HAS DECIDED THAT FURTHER EXPENDITURE OF AGENCY RESOURCES ON THIS INVESTIGATION IS NOT WARRANTED AT THIS TIME: - GM ISSUED CUSTOMER SATISFACTION CAMPAIGN (CSC) 04050A INDECEMBER 2004 TO ADDRESS THE ALLEGED DEFECT IN APPROXIMATELY58,700 SUBJECT VEHICLES, ENCOMPASSING AT LEAST 97 PERCENT OF THECOMPLAINT AND WARRANTY CLAIMS POPULATION.VEHICLES OUTSIDE THECSC 04050A POPULATION CONTAIN A NEWLY DESIGNED TORQUE ANDPOSITION SENSOR AND HAVE EXPERIENCED A RELATIVELY LOW COMPLAINTRATE.THIS CUSTOMER SATISFACTION CAMPAIGN PRESENTLY HAS ACOMPLETION RATE OF 52%. - THE IMPACT ON THE DRIVER?S ABILITY TO CONTROL THESE RELATIVELYSMALL AND LIGHT VEHICLES WAS LIMITED.VRTC TEST ENGINEERS WEREUNABLE TO INDUCE A FAILURE MODE THAT WOULD CAUSE THE EPS TOSUBSTANTIALLY LIMIT THE DRIVER?S ABILITY TO TURN THE VEHICLE IN APARTICULAR DIRECTION OR TO PROVIDE THE DRIVER WITH UNINTENDEDPOWER ASSISTANCE.- THERE IS NO RISK OF FIRE.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT A SAFETY-RELATED DEFECT DOES NOT EXIST.THE AGENCY WILL CONTINUE TO MONITOR COMPLAINTS AND OTHER INFORMATION RELATING TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES AND TAKE FURTHER ACTION IN THE FUTURE IF WARRANTED BY THE CIRCUMSTANCES.(FOR FURTHER DETAILS SEE ATTACHED ENGINEERING ANALYSIS (EA04-018)CLOSING REPORT.)
Steering
IN PERFORMING THIS ENGINEERING ANALYSIS, ODI DETERMINED THAT THE ELECTRIC POWER STEERING SYSTEM IN THE SUBJECT VEHICLES CAN MALFUNCTION OR FAIL, CAUSING THE DRIVER TO LOSE POWER STEERING ASSISTANCE; HOWEVER, DUE TO THE FOLLOWING REASONS, ODI HAS DECIDED THAT FURTHER EXPENDITURE OF AGENCY RESOURCES ON THIS INVESTIGATION IS NOT WARRANTED AT THIS TIME: - GM ISSUED CUSTOMER SATISFACTION CAMPAIGN (CSC) 04050A INDECEMBER 2004 TO ADDRESS THE ALLEGED DEFECT IN APPROXIMATELY58,700 SUBJECT VEHICLES, ENCOMPASSING AT LEAST 97 PERCENT OF THECOMPLAINT AND WARRANTY CLAIMS POPULATION.VEHICLES OUTSIDE THECSC 04050A POPULATION CONTAIN A NEWLY DESIGNED TORQUE ANDPOSITION SENSOR AND HAVE EXPERIENCED A RELATIVELY LOW COMPLAINTRATE.THIS CUSTOMER SATISFACTION CAMPAIGN PRESENTLY HAS ACOMPLETION RATE OF 52%. - THE IMPACT ON THE DRIVER?S ABILITY TO CONTROL THESE RELATIVELYSMALL AND LIGHT VEHICLES WAS LIMITED.VRTC TEST ENGINEERS WEREUNABLE TO INDUCE A FAILURE MODE THAT WOULD CAUSE THE EPS TOSUBSTANTIALLY LIMIT THE DRIVER?S ABILITY TO TURN THE VEHICLE IN APARTICULAR DIRECTION OR TO PROVIDE THE DRIVER WITH UNINTENDEDPOWER ASSISTANCE.- THERE IS NO RISK OF FIRE.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT A SAFETY-RELATED DEFECT DOES NOT EXIST.THE AGENCY WILL CONTINUE TO MONITOR COMPLAINTS AND OTHER INFORMATION RELATING TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES AND TAKE FURTHER ACTION IN THE FUTURE IF WARRANTED BY THE CIRCUMSTANCES.(FOR FURTHER DETAILS SEE ATTACHED ENGINEERING ANALYSIS (EA04-018)CLOSING REPORT.)
PE04031 · Loss Of Electric Power Steering
Opened Mar 30, 2004 · Closed Jul 1, 2004
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System
ODI OPENED PE04-031 BASED ON EIGHT REPORTS OF ALLEGED POWER STEERING FAILURE IN THE SUBJECT VEHICLES.THE COMPLAINTS ALLEGE THAT THE DRIVER SUDDENLY LOST ALL ELECTRIC POWER STEERING ASSISTANCE WITHOUT WARNING MAKING THE VEHICLE DIFFICULT TO STEER. THE SUBJECT VEHICLE UTILIZES AN ELECTRIC POWER STEERING ASSIST SYSTEM (EPS) THAT PROVIDES VARIABLE STEERING ASSISTANCE BASED ON STEERING WHEEL TORQUE, STEERING WHEEL POSTION, AND VEHICLE SPEED.GENERAL MOTORS DOCUMENTS IDENTIFIED THE FOLLOWING TWO FACTORS THAT CONTRIBUTED TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES: A.CONTAMINATION OF THE TORQUE AND POSITION SENSOR FROM THESEPARATION OF GREASE APPLIED TO THE STEERING COLUMN ASSEMBLY. B.ELECTRICAL NOISE GENERATED ON THE POWER AND GROUND SLIP RING SURFACES OF THE TORQUE AND POSITION SENSOR.THE NOISE IS GENERATED AS THE SENSOR CONTACT BRUSHES MOVE ALONG THE SLIP RING SURFACES WHEN THE STEERING WHEEL IS ROTATED.ODI'S ANALYSIS SHOWED FAILURERATES THAT ARE OF CONCERN TO ODI AND INDICATED THAT THE ALLEGED DEFECT IS CONTINUING TO OCCUR IN THE SUBJECT VEHICLES. THIS PRELIMINARY EVALUATION HAS BEEN UPGRADED TO AN ENGINEERING ANALYSIS TO FURTHER INVESTIGATE THIS CONCERN, TO ASSESS THE POTENTIAL SAFETY-RELATED CONSEQUENCES, AND TO DETERMINE THE SCOPE OF THE AFFECTED POPULATION.
Additional source detail variants (2)
Steering:electric Power Assist System
ODI OPENED PE04-031 BASED ON EIGHT REPORTS OF ALLEGED POWER STEERING FAILURE IN THE SUBJECT VEHICLES.THE COMPLAINTS ALLEGE THAT THE DRIVER SUDDENLY LOST ALL ELECTRIC POWER STEERING ASSISTANCE WITHOUT WARNING MAKING THE VEHICLE DIFFICULT TO STEER. THE SUBJECT VEHICLE UTILIZES AN ELECTRIC POWER STEERING ASSIST SYSTEM (EPS) THAT PROVIDES VARIABLE STEERING ASSISTANCE BASED ON STEERING WHEEL TORQUE, STEERING WHEEL POSTION, AND VEHICLE SPEED.GENERAL MOTORS DOCUMENTS IDENTIFIED THE FOLLOWING TWO FACTORS THAT CONTRIBUTED TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES: A.CONTAMINATION OF THE TORQUE AND POSITION SENSOR FROM THESEPARATION OF GREASE APPLIED TO THE STEERING COLUMN ASSEMBLY. B.ELECTRICAL NOISE GENERATED ON THE POWER AND GROUND SLIP RING SURFACES OF THE TORQUE AND POSITION SENSOR.THE NOISE IS GENERATED AS THE SENSOR CONTACT BRUSHES MOVE ALONG THE SLIP RING SURFACES WHEN THE STEERING WHEEL IS ROTATED.ODI'S ANALYSIS SHOWED FAILURERATES THAT ARE OF CONCERN TO ODI AND INDICATED THAT THE ALLEGED DEFECT IS CONTINUING TO OCCUR IN THE SUBJECT VEHICLES. THIS PRELIMINARY EVALUATION HAS BEEN UPGRADED TO AN ENGINEERING ANALYSIS TO FURTHER INVESTIGATE THIS CONCERN, TO ASSESS THE POTENTIAL SAFETY-RELATED CONSEQUENCES, AND TO DETERMINE THE SCOPE OF THE AFFECTED POPULATION.
Steering
ODI OPENED PE04-031 BASED ON EIGHT REPORTS OF ALLEGED POWER STEERING FAILURE IN THE SUBJECT VEHICLES.THE COMPLAINTS ALLEGE THAT THE DRIVER SUDDENLY LOST ALL ELECTRIC POWER STEERING ASSISTANCE WITHOUT WARNING MAKING THE VEHICLE DIFFICULT TO STEER. THE SUBJECT VEHICLE UTILIZES AN ELECTRIC POWER STEERING ASSIST SYSTEM (EPS) THAT PROVIDES VARIABLE STEERING ASSISTANCE BASED ON STEERING WHEEL TORQUE, STEERING WHEEL POSTION, AND VEHICLE SPEED.GENERAL MOTORS DOCUMENTS IDENTIFIED THE FOLLOWING TWO FACTORS THAT CONTRIBUTED TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES: A.CONTAMINATION OF THE TORQUE AND POSITION SENSOR FROM THESEPARATION OF GREASE APPLIED TO THE STEERING COLUMN ASSEMBLY. B.ELECTRICAL NOISE GENERATED ON THE POWER AND GROUND SLIP RING SURFACES OF THE TORQUE AND POSITION SENSOR.THE NOISE IS GENERATED AS THE SENSOR CONTACT BRUSHES MOVE ALONG THE SLIP RING SURFACES WHEN THE STEERING WHEEL IS ROTATED.ODI'S ANALYSIS SHOWED FAILURERATES THAT ARE OF CONCERN TO ODI AND INDICATED THAT THE ALLEGED DEFECT IS CONTINUING TO OCCUR IN THE SUBJECT VEHICLES. THIS PRELIMINARY EVALUATION HAS BEEN UPGRADED TO AN ENGINEERING ANALYSIS TO FURTHER INVESTIGATE THIS CONCERN, TO ASSESS THE POTENTIAL SAFETY-RELATED CONSEQUENCES, AND TO DETERMINE THE SCOPE OF THE AFFECTED POPULATION.