2018 Chevrolet Equinox

I have a 2018 chevy equinox that I bought brand new back in December of 2018. The vacuum pump failed therefore breaking the camshaft which in turn caused failure to my brakes. I went to stop at a light and my brake pedal was hard and my car skidded to a stop through the light. No warning that anything was wrong nothing. My brakes worked fine up until I went to stop at the next light. Then out of the blue my brake pedal was hard and I had no brakes. I almost got into a severe accident due to the brake failure. Evidently there have been other people this has happened to. Extremely dangerous and unsafe. There have been lawsuits filed against GM for faulty vacuum pump part although they were for the year of 2020. GM needs to take a look at this issue and also install some kind of warning. I get warnings for a tire being a little low you would think they could put a warning in for the brake system!! The warranty is still good on my car do I do not have to pay for the repair. In addition when the camshaft broke it threw pieces of metal into the top part of the engine!!

I have purchased a 2018 Chevy equinox. It was damaged on the back bumper (rebuilt title). The backup camera works fine but there is a side detection error that comes on everytime I start the vehicle. The shop replaced the entire harness however that did not fix the issue. I have read 1000's of complaints on this. My vehicle has 45000 miles. This is effecting my gas mileage as well as other safety features. I see this has been an issue in MANY GM models and it has been taken care ( special warranty) but not on a 2018 equinox as of yet. I want to report this problem and see if someone can look into all the other forums etc to see how widespread this really is. The light has came on a few times lately but only when I am parked and not going anywhere??? Thanks in advance.

When buckled, the part of the seat belt buckle where the LAP belt slides through the actual buckle part becomes binding and has to be manual pushed through the buckle in order to move your hips when seated. This issue has absolutely nothing to do with the shoulder part of the belt or the belt not retracting. It is solely an issue with the plastic buckle and the belt not sliding through it when seated. This is a safety issue because the lap belt becomes binding while seated. If the driver needs to shift in the seat, he must pull the shoulder belt out to create give in the belt and then use both hands to manually feed the belt through the buckle. This is unsafe when driving for obvious reasons if the driver is unable to use any hands on the steering wheel. If the driver doesn't continuously adjust the belt in this way, it becomes so tight across the hips that it causes discomfort and redness on the skin and abrasions if the vehicle turns wide or breaks quickly. This intense discomfort makes me avoid wearing my seatbelt which causes obvious risk or poses a risk to myself and other drivers if I need to take both hands off the wheel to adjust it while driving. The front passenger seat belt has the same issue. I began to notice this issue about 6 months ago and have taken the vehicle to a dealer/service center 3 times without any recourse other than being offered the opportunity to replace the entire seat belt system for $700 each.

We were driving home and the car was losing acceleration power. My husband would press on the pedal and there was no acceleration. the all of a sudden the car would seem to get a connection and lurch forward. Thankfully we were were close to home and there wasn't a lot of traffic as it was scary. It ended up being the O2 sensor and I did see recalls on this part for earlier model years of the same car but not for 2018. It appears the issue has not been resolved in the newer models.

Since I bought this car I have had to replace sensors like they’re going out of style. However I would like to report on 3 sensors that went out simultaneously on my vehicle in heavy traffic. I had the vacuum boost sensor for my master cylinder, my cam shaft sensor and my crank shaft sensor go out simultaneously. As a result my vehicle engine cut off completely (battery components still working) and I had zero control over my breaks. I had to use my full body weight on my break pedal to get the vehicle to stop. I was fortune to have been able to pull off into a parking lot. I have had to replace several o2 sensors on this vehicle. I didn’t think anything of having any electrical issues until this happened. My check engine light has stayed on for over a year despite clearing codes and replacing o2 sensors. We check periodically and the only code is usually for the o2 sensor. We can save the sensors we have replaced for inspection if necessary. I had a low engine power signal flash across the infotainment system just before this happened. I was in heavy traffic and I’m just fortunate I was able to get out of the way quickly enough before I hurt myself or someone else. The break issue and loss of power was actually terrifying

When backing into my drive way moving the gear from d to r the car will jump. This has made it to where I fear to park where I have to reverse. As well as when I started driving down the road the auto stop start kicked on while doing 30 when the car powered back on in the busy intersection the car was clunking I pulled over asap and took a look under the car to make sure nothing was leaking when started back up it went away. It’s very unsafe to have a car that you can’t disable the auto stop feature from coming on as if the intersection was not a safe place for this to happen