NHTSA owner reports · September 18, 2026 snapshot.
Engine complaints
147 reportsClear category filter81,000 miles · Aug 14, 2017
EnginePower Train
DRIVING (2013 X3 28I) VEHICLE WITHOUT CONCERNS, INCIDENTS OR WARNINGS UNTIL THE OIL PRESSURE WARNING" LIGHT CAME ON. SLOWING DOWN TO TRY AND MAKE IT THE MILE LEFT TO MAKE IT HOME. AFTER THE "OIL PRESSURE WARNING" CAME ONE, LESS THAN A MINUTE LATER THERE WAS A "DRIVE-TRAIN MALFUNCTION" WARNING. NOW LOOKING FOR A PLACE TO PULL OV…
Read full complaint
DRIVING (2013 X3 28I) VEHICLE WITHOUT CONCERNS, INCIDENTS OR WARNINGS UNTIL THE OIL PRESSURE WARNING" LIGHT CAME ON. SLOWING DOWN TO TRY AND MAKE IT THE MILE LEFT TO MAKE IT HOME. AFTER THE "OIL PRESSURE WARNING" CAME ONE, LESS THAN A MINUTE LATER THERE WAS A "DRIVE-TRAIN MALFUNCTION" WARNING. NOW LOOKING FOR A PLACE TO PULL OVER, IT WAS LESS THAN ANOTHER MINUTE WHEN CAR LOCKED UP AND STOPPED IN THE MIDDLE OF THE ROAD. LIVING ON A CURVY ROAD, I WAS IN A VERY BAD SITUATION, DUE TO BEING BETWEEN TWO CURVES, JUST AFTER DARK. CAR WOULD NOT START OR GO INTO NEUTRAL. IT HAS BEEN 10 WEEKS AND CAR DIAGNOSIS HAS NOT BEEN DETERMINED. WITHOUT WARNINGS AND TOTAL ENGINE FAILURE. I WAS NOT HURT IN ANY WAY, AND THANKFULLY SOMEONE STOPPED TO BLOCK THE CURVE SO PEOPLE WOULD SLOW DOWN. I WAS STUCK WAITING FOR HELP FOR AN HOUR. TOW-TRUCK DRIVER COULDN'T GET INTO NEUTRAL TO LOAD ON HIS TRUCK. I DID BUY THIS AS A 1 OWNER, LEASE RETURN, AND PUT THE TOP ASC WARRANTY ON IT. THE OWNER OF A QUALITY IMPORT REPAIR SHOP SAYS HE HAS NO IDEA AND HAS NEVER COME ACROSS ANYTHING LIKE THIS BEFORE. SHORT OF PULLING EVERYTHING APART TO TRY AND FIGURE OUT A SPECIFIC PROBLEM, HE DOES NOT WANT TO TRY AND REPAIR IT. GOING TO HAVE TO TOW IT TO THE DEALER AND HOPE THEY WILL GIVE SOME ANSWERS. 10 WEEKS AND NO CLOSER TO AN ANSWER THAN ON DAY ONE.
NHTSA ODI #11015269
47,650 miles · Aug 14, 2017
Engine
WHEN MY HUSBAND WAS DRIVING ON THE HIGHWAY AT 10:30 A.M. ON THE 8/8/2017 THE CAR LOST POWER AS IF IT RAN OUT OF GASOLINE. THANK GOD HE WAS ABLE TO PULL OVER TO THE SERVICE LANE WITHOUT GETTING INTO A MAJOR ACCIDENT (HE IS ALWAYS COOL UNDER PRESSURE AS HE RETIRED AS A CAPTAIN IN THE ARMY). HE SHUT OFF THE ENGINE, AND RESTARTED A…
Read full complaint
WHEN MY HUSBAND WAS DRIVING ON THE HIGHWAY AT 10:30 A.M. ON THE 8/8/2017 THE CAR LOST POWER AS IF IT RAN OUT OF GASOLINE. THANK GOD HE WAS ABLE TO PULL OVER TO THE SERVICE LANE WITHOUT GETTING INTO A MAJOR ACCIDENT (HE IS ALWAYS COOL UNDER PRESSURE AS HE RETIRED AS A CAPTAIN IN THE ARMY). HE SHUT OFF THE ENGINE, AND RESTARTED A FEW MINUTES LATER WHEN "DRIVE TRAIN MALFUNCTION" MESSAGE CAME ON. HE CALLED THE DEALERSHIP SERVICE AND WAS TOLD TO BRING THE CAR IN ON 8/10/2017 IN THE MORNING. HE TOLD THEM WHAT HAPPENED AND WAS TOLD HE WILL RECEIVE A CALL BACK THAT EVENING. HE WAS NEVER CONTACTED, AND 3 DAYS LATER WENT TO CHECK WHAT HAPPENED. HE WAS TOLD THAT THE TIMING CHAIN HAS TO BE REPLACED AND IT WILL COST AT LEAST $2,700.00 PLUS... ALMOST A YEAR AGO I WENT TO THEM BECAUSE I HAD WHITE SMOKE COMING OUT OF THE TAILPIPE. SO THEY WERE AWARE THERE WAS A PROBLEM ALREADY AND THEY SHOULD HAVE CHANGED THE TIMING BELT AT THAT TIME (WHILE THE CAR WAS STILL UNDER WARRANTY.) INSTEAD THEY TOTALLY DISREGARD PEOPLE'S SAFETY AND SECURITY AND CREATE UNNECESSARY HAZARDOUS CONDITIONS. I SPENT MORE THAN $50,00 0 ON THE BRAND NEW VEHICLE AND IT ALMOST KILLED MY HUSBAND, READING THROUGH YOUR WEBSITE I SAW MANY OTHERS HAD THE SAME PROBLEMS SOMETHING MUST BE DONE BEFORE SOMEONE GETS KILLED.
NHTSA ODI #11015053
30,300 miles · Jul 18, 2017
Engine
TL* THE CONTACT OWNS A 2013 BMW X3. WHILE DRIVING APPROXIMATELY 35 MPH, THE LOW OIL PRESSURE AND DRIVE TRAIN MALFUNCTION WARNING INDICATORS ILLUMINATED. THE VEHICLE LOST POWER AND THEN STALLED. THE CONTACT COASTED THE VEHICLE TO THE SIDE OF THE ROAD AND HAD IT TOWED TO THE BILL JACOBS BMW DEALER (LOCATED AT 2495 AURORA AVE, NAPE…
Read full complaint
TL* THE CONTACT OWNS A 2013 BMW X3. WHILE DRIVING APPROXIMATELY 35 MPH, THE LOW OIL PRESSURE AND DRIVE TRAIN MALFUNCTION WARNING INDICATORS ILLUMINATED. THE VEHICLE LOST POWER AND THEN STALLED. THE CONTACT COASTED THE VEHICLE TO THE SIDE OF THE ROAD AND HAD IT TOWED TO THE BILL JACOBS BMW DEALER (LOCATED AT 2495 AURORA AVE, NAPERVILLE, IL 60540). THE DEALER DIAGNOSED THAT THERE WERE METAL SHAVINGS IN THE OIL, CAUSING IT NOT TO HAVE COMPRESSION. THE DEALER STATED THAT THE ENGINE NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED DUE TO THE REPAIR COST. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE AND STATED THAT THEY WOULD PAY HALF OF THE REPAIR FEES. THE CONTACT WOULD BE RESPONSIBLE FOR THE OTHER HALF. THE APPROXIMATE FAILURE MILEAGE WAS 30,300.
NHTSA ODI #11006131
100,000 miles · Jul 14, 2017
EngineUnknown Or Other
EARLIER THIS YEAR WHILE DRIVING MY 2013 BMW X3 ON THE HIGHWAY IT BROKE DOWN WITH LITTLE WARNING. FORTUNATELY I WAS ABLE TO GET TO AN EXIT RAMP BEFORE MY CAR COMPLETELY FAILED. AFTER HAVING IT FLAT BEDDED TO A MECHANIC WHO HAD TO PUSH THE VEHICLE INTO THE SHOP THEY VERIFIED THAT THE VEHICLE WOULD CRANK OVER AND NOT START. IT WA…
Read full complaint
EARLIER THIS YEAR WHILE DRIVING MY 2013 BMW X3 ON THE HIGHWAY IT BROKE DOWN WITH LITTLE WARNING. FORTUNATELY I WAS ABLE TO GET TO AN EXIT RAMP BEFORE MY CAR COMPLETELY FAILED. AFTER HAVING IT FLAT BEDDED TO A MECHANIC WHO HAD TO PUSH THE VEHICLE INTO THE SHOP THEY VERIFIED THAT THE VEHICLE WOULD CRANK OVER AND NOT START. IT WAS RELATIVELY CLEAR FROM THE SOUND THE ENGINE WAS MAKING DURING THE STARTER ENGAGEMENT THAT THE CAMSHAFT TIMING WAS OFF. THE VALVE COVER WAS REMOVED AND THE MECHANIC VERIFIED THAT THE TIMING WAS INDEED OFF. THE TIMING CHAIN HAD JUMPED TIME ON BOTH THE INTAKE AND EXHAUST CAMSHAFTS. THE TIMING WAS OFF DUE TO EXCESSIVE SLACK IN THE TIMING CHAIN DUE TO A FAILED CHAIN TENSIONER. THIS SHOULD NOT HAPPEN ON A 2013 BMW WITH MAINLY HIGHWAY MILES. I WAS TOLD I NEED A NEW ENGINE THAT WILL COST UPWARDS OF $15,000 OR BUY A SLIGHTLY USED ONE FOR APPROXIMATELY $9,000. I'VE REACHED OUT TOT HE DEALER AND BMW NA WITH NO RELIEF. SIMILAR ISSUES HAVE BEEN IDENTIFIED IN THE X5 AND OTHER BMW CARS WHICH WERE RECALLED BUT FOR SOME REASON NO RECALL WAS SENT OUT ON THE N20 ENGINE FOR THE X3. FROM A QUICK INTERNET SEARCH THERE ARE MANY X3 OWNERS THAT HAVE THE SAME OR SIMILAR PROBLEMS. SOMETHING NEEDS TO BE DONE TO GET RELIEF FOR THESE OWNERS. UNFORTUNATELY THIS ONCE PROUD VEHICLE MAKER THAT NO LONGER BACKS THE LONGEVITY OF THE LUXURY CAR THEY BUILD.
NHTSA ODI #11005332
50,000 miles · Jun 27, 2017
Engine
I HAVE A 2013 X3 28I THAT WAS PURCHASED FAIRLY NEW WITH 15K MILES ON IT AND HAS HAD ALL BMW RECOMMENDED MAINTENANCE AT A BMW DEALER. I HAVE EXACTLY 50K MILES ON THE CAR. A COUPLE OF DAYS AGO, WITH NO WARNING THE TIMING CHAIN BROKE AND BLEW THE ENGINE. I HAD JUST TAKEN IT TO THE DEALERSHIP A COUPLE OF WEEKS PRIOR FOR MAINTENANC…
Read full complaint
I HAVE A 2013 X3 28I THAT WAS PURCHASED FAIRLY NEW WITH 15K MILES ON IT AND HAS HAD ALL BMW RECOMMENDED MAINTENANCE AT A BMW DEALER. I HAVE EXACTLY 50K MILES ON THE CAR. A COUPLE OF DAYS AGO, WITH NO WARNING THE TIMING CHAIN BROKE AND BLEW THE ENGINE. I HAD JUST TAKEN IT TO THE DEALERSHIP A COUPLE OF WEEKS PRIOR FOR MAINTENANCE AND THEY SAID EVERYTHING LOOKED GREAT. THE DEALER FIRST TOLD ME IT WAS GOING TO COST OVER 20K TO REPLACE THE ENGINE. BMW GOT INVOLVED AND NOW I'M TOLD IT WILL COST JUST OVER 15K PLUS TAXES. I STARTED CHECKING ONLINE AND NOTICED THAT BMW HAS HAD A LOT OF PROBLEMS WITH THE TIMING CHAIN, HOWEVER THEY DON'T LIST THE X3 AS ONE OF THE CARS WITH THE PROBLEM. AT 4 YEARS OLD AND 50K MILES, I WOULD THINK THE TIMING CHAIN SHOULDN'T BREAK, AND DEFINITELY SHOULDN'T COST 1/3 OF A NEW CAR TO REPAIR.
NHTSA ODI #11001808
25,000 miles · Mar 27, 2017
EnginePower TrainVehicle Speed Control
SHIFTING IS ERRATIC, ESPECIALLY ACCELERATING FROM A STOP. BOTH WIFE AND MYSELF NOTICED THIS ON SEPARATE OCCASIONS DRIVING BY OURSELVES. DEALER SAYS THERE ARE NO CODES AND IT DRIVES LIKE ALL OTHER X3'S. IT DOES NOT DRIVE LIKE OTHER X3'S AS WE WERE GIVEN A NEW X3 AS A LOANER.
NHTSA ODI #10968769
60,000 miles · Feb 13, 2017
Engine
I HAVE 3 PARTS IN MY VEHICLE THAT ARE NOW IDENTIFIED AS NEEDING REPLACEMENT BY MY MECHANIC. I WENT TO THE MECHANIC AFTER MY VEHICLE WENT INTO "LIMP" MODE WHILE DRIVING AT 45MPH IN NORMAL CONDITIONS AND I RECEIVED A MESSAGE STATING MY VEHICLE WAS OVERHEATING. MY MECHANIC ADVISED THAT I NEED A NEW WATER PUMP, A NEW THERMOSTAT, A…
Read full complaint
I HAVE 3 PARTS IN MY VEHICLE THAT ARE NOW IDENTIFIED AS NEEDING REPLACEMENT BY MY MECHANIC. I WENT TO THE MECHANIC AFTER MY VEHICLE WENT INTO "LIMP" MODE WHILE DRIVING AT 45MPH IN NORMAL CONDITIONS AND I RECEIVED A MESSAGE STATING MY VEHICLE WAS OVERHEATING. MY MECHANIC ADVISED THAT I NEED A NEW WATER PUMP, A NEW THERMOSTAT, AND WHILE IT'S NOT RELATED, I ALSO NEED A NEW OIL HOUSING GASKET. IT SOUNDS LIKE THESE ARE ALL COMMON FAILURES ON THESE VEHICLES AND MY MECHANIC NOTED "IT'S NOT A MATTER OF IF THESE ITEMS WILL FAIL, BUT WHEN". MOREOVER, ONE SIMPLE GOOGLE SEARCH WILL TELL YOU THE SAME. IF THESE PARTS ARE TRULY AN ISSUE, WHY ARE THEN NOT RECALLED? MY CAR GOING INTO LIMP MODE WHILE DRIVING ON A HIGHWAY SHOULD BE CONSIDERED A SAFETY CONCERN, PARTICULARLY IN POPULATED METRO AREAS WITH A TODDLER IN THE BACK SEAT. UNFORTUNATELY, TO REPAIR THESE 3 PARTS, I'VE BEEN QUOTED $1500 FOR THE REPAIRS, WHICH IS ABSOLUTELY RIDICULOUS FOR A CAR THAT HAS 60,000 MILES ON IT.
NHTSA ODI #10954209
57,000 miles · Feb 10, 2017
Engine
ENGINE OVERHEAT WARNING DUE TO WATER PUMP ISSUES. JUST UNDER 5 YEARS OF BRAND NEW PURCHASE. SEE SIMILAR PART HAS EXCESSIVE COMPLAINTS. HTTP://X3.XBIMMERS.COM/FORUMS/SHOWTHREAD.PHP?T=1219853&PAGE=2 BMW INITIALLY CHARGED ME AS A THERMOSTAT ISSUE, AND REPLACED IT AFTER 3 MONTHS BACK-ORDERED PARTS. 1 DAY AFTER THERMOSTAT REPLACEM…
Read full complaint
ENGINE OVERHEAT WARNING DUE TO WATER PUMP ISSUES. JUST UNDER 5 YEARS OF BRAND NEW PURCHASE. SEE SIMILAR PART HAS EXCESSIVE COMPLAINTS. HTTP://X3.XBIMMERS.COM/FORUMS/SHOWTHREAD.PHP?T=1219853&PAGE=2 BMW INITIALLY CHARGED ME AS A THERMOSTAT ISSUE, AND REPLACED IT AFTER 3 MONTHS BACK-ORDERED PARTS. 1 DAY AFTER THERMOSTAT REPLACEMENT, SYMPTOMS RE-APPEARED. THIS TIME THEY ARE REPLACING OTHER PARTS. WITH NUMBER OF PEOPLE COMPLAINING ABOUT IT, IT SHOULD BE CONSIDERED AS A RECALL. EVERY REPAIR WITH BMW IS VERY EXPENSIVE.
NHTSA ODI #10953923
65,000 miles · Dec 20, 2016
Engine
TIMING CHAIN MALFUNCTION/ENGINE FAILURE
NHTSA ODI #10936572
78,000 miles · Dec 12, 2016
Electrical SystemEnginePower Train
TL* THE CONTACT OWNS A 2013 BMW X3. THE CONTACT STATED THAT THE WARNING INDICATORS FLASHED FOR THE OIL PRESSURE LOW AND DRIVE TRAIN, AND THE VEHICLE SUDDENLY DECELERATED WITHOUT WARNING. THE VEHICLE STARTED TO COAST AND RANDOMLY STALLED. THE VEHICLE WAS UNABLE TO RESTART AND WAS TOWED TO AN INDEPENDENT MECHANIC WHO WAS UNABLE TO…
Read full complaint
TL* THE CONTACT OWNS A 2013 BMW X3. THE CONTACT STATED THAT THE WARNING INDICATORS FLASHED FOR THE OIL PRESSURE LOW AND DRIVE TRAIN, AND THE VEHICLE SUDDENLY DECELERATED WITHOUT WARNING. THE VEHICLE STARTED TO COAST AND RANDOMLY STALLED. THE VEHICLE WAS UNABLE TO RESTART AND WAS TOWED TO AN INDEPENDENT MECHANIC WHO WAS UNABLE TO REPLICATE AND DIAGNOSE THE FAILURE. THE VEHICLE WAS TOWED TO THE DEALER WHERE IT WAS DIAGNOSED THAT METAL SHAVINGS WERE IN THE OIL. FURTHER DIAGNOSTIC TESTING WAS REQUIRED TO DETERMINE THE CAUSE OF THE FAILURE. THE VEHICLE WAS THEN TOWED TO A SECOND INDEPENDENT REPAIR SHOP FOR FURTHER TESTING. THE DEALER AND MANUFACTURER WERE NOTIFIED. THE APPROXIMATE FAILURE MILEAGE WAS 78,000.
NHTSA ODI #10934798
Official recalls
7Aug 13, 2024
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence & remedy
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
Additional source detail variants (2)
Electrical System:wiring:connectors/plugs/receptacles
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
Engine And Engine Cooling:cooling System:pump
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
Jul 11, 2024
BMW of North America, LLC (BMW) is recalling certain 2015 6 Series Gran Coupe, 2014 5 Series Gran Turismo, 2014 5 Series Sedan, 2015 6 Series Convertible, 2015 6 Series Coupe, 2014 X5, 2013-2014 X3, 2014-2015 3 Series Sedan, 2014 4 Series Coupe, 2014 4 Series Convertible, 2014 3 Series Gran Turismo, and 2015 4 Series Gran Coupe vehicles. Please see the recall report for the complete list of models. The driver's air bag inflator may explode during deployment, due to a manufacturing defect.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, increasing the risk of injury or death.
Remedy: The driver's front air bag will be replaced, free of charge. Owner notification letters were mailed September 6, 2024. Owners may contact BMW customer service at 1-800-525-7417.
Aug 8, 2017
BMW of North America, LLC. (BMW) is recalling certain 2012-2013 BMW X3 xDrive28i, X3 xDrive35i, and M6 Convertible vehicles and 2013 M6 Coupe vehicles. The affected vehicles have a driver's frontal air bag inflator that may have been improperly welded.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator housing could separate from the base plate and result in metal striking the vehicle occupants, potentially resulting in serious injury or death.
Remedy: BMW will notify owners, and dealers will replace the driver's front air bag module, free of charge. The recall began October 6, 2017. Owners may contact BMW customer service at 1-800-525-7417.
May 23, 2016
BMW of North America, LLC (BMW) is recalling certain model year 2011-2017, X3 sDrive28i, X3 xDrive28i and X3 xDrive35i, vehicles manufactured July 2, 2010 to April 14, 2016, 2015-2017 X3 xDrive28d vehicles manufactured March 10, 2014 to March 31, 2016, and 2015-2017 x4 xDrive28i, X4 xDrive35i and X4 xDriveM40i vehicles manufactured March3, 2014 to April 15, 2016. The affected vehicles have lower anchor bars for securing child restraint seats that may become damaged when using the European-ISOFIX-type, rigid-style connector, child restraint system.
Consequence & remedy
Consequence: Damaged lower anchor bars may increase the child's risk of injury in the event of a crash.
Remedy: BMW will notify owners, and dealers will weld a reinforcing bracket to the lower anchor bars and the vehicle body, free of charge. The recall began on July 13, 2016. Owners may contact BMW customer service at 1-800-525-7417.
Oct 7, 2014
BMW of North America LLC (BMW) is recalling certain model year 2014 BMW 328i xDrive Sports Wagon, 2012-2014 BMW 320i Sedan, 328i Sedan, 320i xDrive Sedan, 328i xDrive Sedan, 2012-2013 BMW 528i Sedan, 528i xDrive Sedan, 2013-2014 BMW X1 sDrive28i, X1 xDrive28i Sports Activity Vehicle, 2013-2014 BMW X3 xDrive28i Sports Activity Vehicle, 2012-2014 BMW Z4 sDrive28i Roadster, and 2014 BMW 428i Coupe, and 428i xDrive Coupe. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail. Note: This recall is an expansion of recall 13V-454.
Consequence & remedy
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will install a locking ring in the camshaft to retain the camshaft seal disk in the proper location, free of charge. The recall began on December 2, 2014. Owners may contact BMW customer service at 1-800-525-7417.
Additional source detail variants (2)
Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
BMW of North America LLC (BMW) is recalling certain model year 2014 BMW 328i xDrive Sports Wagon, 2012-2014 BMW 320i Sedan, 328i Sedan, 320i xDrive Sedan, 328i xDrive Sedan, 2012-2013 BMW 528i Sedan, 528i xDrive Sedan, 2013-2014 BMW X1 sDrive28i, X1 xDrive28i Sports Activity Vehicle, 2013-2014 BMW X3 xDrive28i Sports Activity Vehicle, 2012-2014 BMW Z4 sDrive28i Roadster, and 2014 BMW 428i Coupe, and 428i xDrive Coupe. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail. Note: This recall is an expansion of recall 13V-454.
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will install a locking ring in the camshaft to retain the camshaft seal disk in the proper location, free of charge. The recall began on December 2, 2014. Owners may contact BMW customer service at 1-800-525-7417.
Service Brakes, Hydraulic:power Assist:vacuum
BMW of North America LLC (BMW) is recalling certain model year 2014 BMW 328i xDrive Sports Wagon, 2012-2014 BMW 320i Sedan, 328i Sedan, 320i xDrive Sedan, 328i xDrive Sedan, 2012-2013 BMW 528i Sedan, 528i xDrive Sedan, 2013-2014 BMW X1 sDrive28i, X1 xDrive28i Sports Activity Vehicle, 2013-2014 BMW X3 xDrive28i Sports Activity Vehicle, 2012-2014 BMW Z4 sDrive28i Roadster, and 2014 BMW 428i Coupe, and 428i xDrive Coupe. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail. Note: This recall is an expansion of recall 13V-454.
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will install a locking ring in the camshaft to retain the camshaft seal disk in the proper location, free of charge. The recall began on December 2, 2014. Owners may contact BMW customer service at 1-800-525-7417.
Nov 15, 2013
BMW of North America, LLC (BMW) is recalling certain model year 2013 X3 xDrive 28i/35i vehicles manufactured February 11, 2013, through February 27, 2013. Due to a production process error, the tear seam on the instrument panel was not manufactured correctly.
Consequence & remedy
Consequence: In the event of a crash, the air bag could improperly deploy, thereby reducing the effectiveness of the air bag's protection and increasing the risk of injury to the front passenger. In addition, parts or fragments from the air bag system could strike and injure the front passenger or other vehicle occupants.
Remedy: BMW has notified owners and dealers will replace the instrument panel, free of charge. The recall began on December 11, 2013. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Additional source detail variants (2)
Electrical System: Instrument Cluster/panel
BMW of North America, LLC (BMW) is recalling certain model year 2013 X3 xDrive 28i/35i vehicles manufactured February 11, 2013, through February 27, 2013. Due to a production process error, the tear seam on the instrument panel was not manufactured correctly.
Consequence: In the event of a crash, the air bag could improperly deploy, thereby reducing the effectiveness of the air bag's protection and increasing the risk of injury to the front passenger. In addition, parts or fragments from the air bag system could strike and injure the front passenger or other vehicle occupants.
Remedy: BMW has notified owners and dealers will replace the instrument panel, free of charge. The recall began on December 11, 2013. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Air Bags
BMW of North America, LLC (BMW) is recalling certain model year 2013 X3 xDrive 28i/35i vehicles manufactured February 11, 2013, through February 27, 2013. Due to a production process error, the tear seam on the instrument panel was not manufactured correctly.
Consequence: In the event of a crash, the air bag could improperly deploy, thereby reducing the effectiveness of the air bag's protection and increasing the risk of injury to the front passenger. In addition, parts or fragments from the air bag system could strike and injure the front passenger or other vehicle occupants.
Remedy: BMW has notified owners and dealers will replace the instrument panel, free of charge. The recall began on December 11, 2013. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Sep 26, 2013
BMW of North America LLC (BMW) is recalling certain model year 2012-2014 320i, 328i, 320i xDrive, and 328i xDrive sedans; model year 2014 328i xDrive Sports Wagons; model year 2012-2013 528i and 528i xDrive sedans, model year 2013-2014 X1 sDrive28i and X1 xDrive28i vehicles and model year 2012-2014 Z4 sDrive28i roadsters. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail.
Consequence & remedy
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will modify the vehicles to prevent insufficient vacuum pump lubrication, free of charge. The safety recall began on January 31, 2014. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Additional source detail variants (2)
Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
BMW of North America LLC (BMW) is recalling certain model year 2012-2014 320i, 328i, 320i xDrive, and 328i xDrive sedans; model year 2014 328i xDrive Sports Wagons; model year 2012-2013 528i and 528i xDrive sedans, model year 2013-2014 X1 sDrive28i and X1 xDrive28i vehicles and model year 2012-2014 Z4 sDrive28i roadsters. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail.
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will modify the vehicles to prevent insufficient vacuum pump lubrication, free of charge. The safety recall began on January 31, 2014. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Service Brakes, Hydraulic:power Assist:vacuum
BMW of North America LLC (BMW) is recalling certain model year 2012-2014 320i, 328i, 320i xDrive, and 328i xDrive sedans; model year 2014 328i xDrive Sports Wagons; model year 2012-2013 528i and 528i xDrive sedans, model year 2013-2014 X1 sDrive28i and X1 xDrive28i vehicles and model year 2012-2014 Z4 sDrive28i roadsters. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail.
Consequence: A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will modify the vehicles to prevent insufficient vacuum pump lubrication, free of charge. The safety recall began on January 31, 2014. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
PE13030 · Loss Of Power Assist Braking
Opened Sep 6, 2013 · Closed Oct 25, 2013
Status: closed (inferred from source dates) · Service Brakes, Hydraulic:power Assist:vacuum
In a letter dated September 26, 2013, BMW Group submitted a safety recall notice to NHTSA identifying a defect condition in the vacuum pump oil supply that may result in loss of power assist braking in 76,191 model year (MY) 2012 through 2014 BMW 3-Series, 5-Series, X1 SAV, X3 SAV, and Z4 vehicles equipped with 4-cylinder engines (NHTSA Recall 13V-454).According to BMW, movement of the seal disk within the camshaft may result in blocking of the oil supply to the vacuum pump, resulting in improper pump operation and loss of power assist braking.On July 11, 2013, BMW initiated a change to the camshaft geometry that prevented the seal disk from blocking the oil port.BMW has not received any braking complaints related to loss of power assist after the design change was implemented in production.The owners of all affected vehicles will be contacted by mail and asked to take their vehicle to a BMW dealer who will install a locking ring into the camshaft to keep the seal disk in its proper location.BMW expects to begin dealer and owner notification in November 2013 and complete dealer and owner notification in December when the remedy is expected to be available.Based on the actions taken by BMW, this investigation is closed.
Illustration