NHTSA owner reports · September 18, 2026 snapshot.
Fuel System, Gasoline complaints
4 reportsClear category filter8,000 miles · Aug 11, 2008
Fuel System, Gasoline
CRUISING ON THE HIGHWAY, THE VEHICLE STARTS MISFIRING AND LOSES POWER. AFTERWARD THE ENGINE IS RUNNING ROUGH AND CONTINUES IN "ENGINE FAILURE" MODE WITH REDUCED POWER. PROBLEM DIAGNOSED AS HIGH PRESSURE FUEL PUMP FAILURE. FUEL PUMP REPLACED THREE TIMES IN THE LAST MONTH AND KEEPS FAILING WITH THE SAME SYMPTOMS. THE VEHICLE IS 20…
Read full complaint
CRUISING ON THE HIGHWAY, THE VEHICLE STARTS MISFIRING AND LOSES POWER. AFTERWARD THE ENGINE IS RUNNING ROUGH AND CONTINUES IN "ENGINE FAILURE" MODE WITH REDUCED POWER. PROBLEM DIAGNOSED AS HIGH PRESSURE FUEL PUMP FAILURE. FUEL PUMP REPLACED THREE TIMES IN THE LAST MONTH AND KEEPS FAILING WITH THE SAME SYMPTOMS. THE VEHICLE IS 2008 BMW 335I. *TR
NHTSA ODI #10237786
4,000 miles · Jul 30, 2008
Fuel System, Gasoline
ON SATURDAY, JULY 26TH, I DROVE A SHORT DISTANCE FROM MY HOME (AFTER A LONG CRANKING START) AND THE CAR SEEMED DRIVE NORMALLY UNTIL I TURNED TO ENTER A SHOPPING CENTER(FORTUNATELY, A SHORT DISTANCE FROM MY HOME, AS IT TURNS OUT). WHILE DRIVING INTO THE SHOPPING CENTER ENTRANCE (10 OR 15 MILES PER HOUR) I FELT A JOLT AND THE CAR …
Read full complaint
ON SATURDAY, JULY 26TH, I DROVE A SHORT DISTANCE FROM MY HOME (AFTER A LONG CRANKING START) AND THE CAR SEEMED DRIVE NORMALLY UNTIL I TURNED TO ENTER A SHOPPING CENTER(FORTUNATELY, A SHORT DISTANCE FROM MY HOME, AS IT TURNS OUT). WHILE DRIVING INTO THE SHOPPING CENTER ENTRANCE (10 OR 15 MILES PER HOUR) I FELT A JOLT AND THE CAR SLOWED DRAMATICALLY. I CHECKED THE REARVIEW MIRROR TO SEE IF I HAD BEEN HIT BY ANOTHER CAR, BUT HAD NOT. I THEN REALIZED THAT THE ENGINE WAS NOT RUNNING, PUT IN THE CLUTCH AND COASTED TO A STOP AT A STOP SIGN. I ATTEMPTED TO RE-START THE CAR BUT WAS UNABLE TO. THE ENGINE 'TURNED OVER' BUT WOULD NOT START. THERE WERE NO WARNING LIGHTS OR MESSAGES BEFORE OR AFTER THE FAILURE OR AT ANY OTHER TIME. AT THIS POINT, I USED BMW ASSIST TO GET HELP SINCE I WAS PARTIALLY BLOCKING A BUSY INTERSECTION WITHIN THE SHOPPING CENTER. A TOW TRUCK ARRIVED ABOUT 45 MINUTES AFTER MY CALL TO BMW ASSIST. WHEN THE TOW TRUCK ARRIVED, THE DRIVER POINTED OUT A LEAK AND PUDDLE/STAIN ON THE ASPHALT COMING FROM THE FRONT OF THE CAR. THE STAIN WAS ABOUT 2 BY 3 FEET. THERE WAS ALSO A SMELL OF GASOLINE. WHEN THE CAR WAS TOWED TO THE DEALERSHIP, THE SERVICE ADVISOR ALSO NOTICED GAS STILL LEAKING FROM THE FRONT OF THE CAR AND DRIPPING ON THE GROUND. A LOANER CAR AND I WAS ON MY WAY. ON MONDAY, JULY 28TH I CALLED THE SA TO CHECK THE STATUS OF THE CAR AT ABOUT 3:00 PM. I WAS TOLD THAT THE HIGH PRESSURE FUEL PUMP AND A CONNECTING HOSE NEEDED TO BE REPLACED. HE SAID THE PARTS WERE ORDERED AND SHOULD BE ON HAND BY WEDNESDAY, JULY 30 TO BE INSTALLED. I ASKED ABOUT THE HOSE, AND THE RESULTING GASOLINE LEAK AND HE COMMENTED ABOUT THE LARGE AMOUNT OF GAS THAT HAD BEEN SPRAYED OUT IN THE ENGINE COMPARTMENT DUE TO THE FAILURE OF THE HOSE. THERE EASILY COULD HAVE BEEN A CATASTROPHIC FIRE DUE TO THE MAGNITUDE OF THE GASOLINE LEAK. THE DEALERSHIP WILL REPAIR THE PUMP AND HOSE UNDER WARRANTY. THE CAR IS A BMW 335I. *TR
NHTSA ODI #10236429
188 miles · Jun 19, 2008
Fuel System, Gasoline
FUEL PUMP REPLACED AFTER 188 MILES. CAR ALREADY SHOWED SYMPTOM 1 DAY AFTER DELIVERY. HESITATED TO START. DEALER DIAGNOSED DEFECTIVE FUEL PUMP AND REPLACED IT. IMPORTANT NOTE TO CAR. IT IS A 335I, MODEL TYPE E93. YOUR SYSTEM DOESN'T LIST IT, SO I USED M3. *TR
NHTSA ODI #10231557
2,500 miles · May 29, 2008
Fuel System, Gasoline
CAR HAD LONGER AND LONGER CRANK TIMES AT STARTUP. OVER THE SPAN OF A WEEK THE STARTUP TIME BEFORE IGNITION TOOK UP TO 5 SECONDS. THE CAR WAS BROUGHT IN, AND THE HIGH PRESSURE FUEL PUMP WAS FOUND TO BE FAULTY. REPLACED BY DEALER FREE OF CHARGE. *TR
NHTSA ODI #10229257
Official recalls
5Jan 15, 2020
BMW of North America, LLC (BMW) is recalling certain 2008-2013 128i and 135i Convertibles, 128i, 135i, and M Coupes, 2007-2010 X3 30si and X3 xDrive30i, 2013-2015 X1 sDrive28i, X1 xDrive28i and X1 xDrive35i, 2007-2013 328i, 328i xDrive, 335i, 335is, 335i xDrive and M3 Coupes, 2006-2011 328i, 328xi, 328i xDrive, 325i, 325xi, 330i, 330xi, 335i, 335xi, 335i xDrive and M3, 2009-2011 335D, 2006-2012 325xi, 328i, 328xi and 328i xDrive, 2010-2011 X6 ActiveHybrid, 2007-2013 328i, 335i, 335is, M3 Coupes, X5 30si, X5 xDrive30i, X5 xDrive35i, X5 48i, X5 xDrive48i, X5 xDrive50i and X5 M, 2009-2013 X5 xDrive35d and 2008-2014 X6 xDrive35i, X6 xDrive50i and X6M vehicles equipped with non-desiccated driver frontal air bag inflators containing phase stabilized ammonium nitrate (PSAN) that were used as interim remedy parts for previous Takata recalls. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: BMW will notify owners, and dealers will replace the driver air bag. On X5 and X6 vehicles, only the inflator will be replaced. All repairs will be performed free of charge. The recall began March 11, 2020. Owners may contact BMW customer service at 1-800-525-7417.
Jun 19, 2019
BMW of North America, LLC (BMW) is recalling certain 2009 328i and 328xi, 2009-2011 335d, 2008-2012 M3 Coupe and M3 Convertible, and 2008-2011 M3 Sedan vehicles. The connection of the positive battery cable at the fuse box terminal may degrade, resulting in an intermittent loss of electrical power.
Consequence & remedy
Consequence: A loss of electrical power can cause the vehicle to stall, increasing the risk of a crash.
Remedy: BMW will notify owners, and dealers will replace and secure the positive battery cable connector, free of charge. The recall began August 14, 2019. Owners may contact BMW customer service at 1-800-525-7417. Note: This recall is an expansion of a previous recall, number 18V-314.
Additional source detail variants (3)
Electrical System:wiring:fuses And Circuit Breakers
BMW of North America, LLC (BMW) is recalling certain 2009 328i and 328xi, 2009-2011 335d, 2008-2012 M3 Coupe and M3 Convertible, and 2008-2011 M3 Sedan vehicles. The connection of the positive battery cable at the fuse box terminal may degrade, resulting in an intermittent loss of electrical power.
Consequence: A loss of electrical power can cause the vehicle to stall, increasing the risk of a crash.
Remedy: BMW will notify owners, and dealers will replace and secure the positive battery cable connector, free of charge. The recall began August 14, 2019. Owners may contact BMW customer service at 1-800-525-7417. Note: This recall is an expansion of a previous recall, number 18V-314.
Electrical SYSTEM:12V/24V/48V Battery:cables
BMW of North America, LLC (BMW) is recalling certain 2009 328i and 328xi, 2009-2011 335d, 2008-2012 M3 Coupe and M3 Convertible, and 2008-2011 M3 Sedan vehicles. The connection of the positive battery cable at the fuse box terminal may degrade, resulting in an intermittent loss of electrical power.
Consequence: A loss of electrical power can cause the vehicle to stall, increasing the risk of a crash.
Remedy: BMW will notify owners, and dealers will replace and secure the positive battery cable connector, free of charge. The recall began August 14, 2019. Owners may contact BMW customer service at 1-800-525-7417. Note: This recall is an expansion of a previous recall, number 18V-314.
Electrical System
BMW of North America, LLC (BMW) is recalling certain 2009 328i and 328xi, 2009-2011 335d, 2008-2012 M3 Coupe and M3 Convertible, and 2008-2011 M3 Sedan vehicles. The connection of the positive battery cable at the fuse box terminal may degrade, resulting in an intermittent loss of electrical power.
Consequence: A loss of electrical power can cause the vehicle to stall, increasing the risk of a crash.
Remedy: BMW will notify owners, and dealers will replace and secure the positive battery cable connector, free of charge. The recall began August 14, 2019. Owners may contact BMW customer service at 1-800-525-7417. Note: This recall is an expansion of a previous recall, number 18V-314.
Oct 25, 2017
BMW of North America, LLC (BMW) is recalling certain 2006-2011 323i, 325i, 325xi, 328i, 328xi, 330i, 330xi, 335i, 335xi and M3, 2007-2011 328i xDrive, 335i xDrive and 335is and 2009-2011 335d vehicles. The wiring and electrical connectors for the system that controls air flow for the heating and air conditioning system may overheat.
Consequence & remedy
Consequence: Wiring that overheats could cause the electrical connectors to melt, and increase the risk of a fire, even when the vehicle is unattended.
Remedy: BMW will notify owners, and dealers will replace the wiring and electrical connectors, free of charge. Interim letters were mailed on November 27, 2017. Owners will receive a second notice when the remedy becomes available. Owners may contact BMW customer service at 1-800-525-7417.
Feb 5, 2016
BMW of North America, LLC (BMW) is recalling certain model year 2008-2013 128i and 135i coupes and convertibles and 1 Series M coupes, 2006-2011 325i, 325xi, 328i, 328xi, 328i xDrive, 330i, 330xi, 335i, 335xi, 335i xDrive Sedans, 2009-2011 335d sedans, 2006-2012 325xiT, 328i and 328xi sports wagons, 2007-2013 328i, 328xi, 328i xDrive, 335i, 335xi, 335i xDrive, 335is and M3 Coupes and Convertibles, 2013-2015 X1 sDrive28i, X1 xDrive28i and X1 xDrive35i SAVs, 2007-2010 X3 xDrive30i SAVs, 2007-2013 X5 xDrive30i, X5 xDrive35i, X5 xDrive48i, X5 xDrive50i and X5 M SAVs, 2009-2013 BMW X5 xDrive35d SAVs, 2008-2014 X6 xDrive35i, X6 xDrive50i, and X6 M SACs, 2010-2011 BMW X6 xDrive50i SACs and 2008-2011 M3 Sedan vehicles. Upon deployment of the driver's frontal air bag, excessive internal pressure may cause the inflator to rupture.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: BMW will notify owners, and dealers will replace the driver's frontal air bag module or inflator depending on the vehicle model, free of charge. The recall began March 9, 2018. Owners may contact BMW customer service at 1-800-525-7417.
Nov 14, 2008
BMW IS RECALLING 2,500 MY 2008-2009 M3 PASSENGER VEHICLES WITH AN OPTIONAL DOUBLE CLUTCH TRANSMISSION. THE PROBLEM INVOLVES THE DOUBLE CLUTCH GEARBOX. IN A SITUATION OF RAPID VEHICLE DECELERATION, THE TRANSMISSION SOFTWARE MAY PERFORM A MULTISTAGE DOWNSHIFT.
Consequence & remedy
Consequence: IN THAT SITUATION, AT LOW VEHICLE SPEEDS, IT IS POSSIBLE FOR THE ENGINE TO STALL INCREASING THE RISK OF A CRASH.
Remedy: DEALERS WILL REPROGRAM THE ENGINE AND TRANSMISSION ELECTRONIC CONTROL UNIT WITH UPDATED SOFTWARE FREE OF CHARGE. THE RECALL BEGAN ON DECEMBER 3, 2008. OWNERS MAY CONTACT BMW AT 1-800-831-1117.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Illustration