The contact’s son owns a 2015 BMW 328I. The contact received notification of NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System). The contact stated that while his son was driving approximately 45 MPH, the vehicle stalled. The vehicle was not able to be restarted. The vehicle was towed to a dealer whe…
Read full complaint
The contact’s son owns a 2015 BMW 328I. The contact received notification of NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System). The contact stated that while his son was driving approximately 45 MPH, the vehicle stalled. The vehicle was not able to be restarted. The vehicle was towed to a dealer where it was diagnosed and it was determined that the timing chain had failed, causing the engine to seize. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was approximately 137,000.
NHTSA ODI #11621082
Mileage unknown · Sep 14, 2024
Engine
While driving the vehicle it completely stopped and lost all power. No warning was given. We took it to dealership and was told timing chain failed causing engine damage. We were told this is a common problem and I only had vehicle for a little over a year. I am stuck with 5 years left on a vehicle I can’t drive or pay the repai…
Read full complaint
While driving the vehicle it completely stopped and lost all power. No warning was given. We took it to dealership and was told timing chain failed causing engine damage. We were told this is a common problem and I only had vehicle for a little over a year. I am stuck with 5 years left on a vehicle I can’t drive or pay the repair cost of $14,000.
NHTSA ODI #11614589
Mileage unknown · Dec 26, 2023
EngineService Brakes
On BMW there is a consistent problem with the oil filter housing gasket leaking oil which runs down and gets on the V-belt causing slipping that affects power steering. It is common problem for the emergency brake plastic clip to brake and cause the emergency brake cable that runs above the drive shaft to scrape the driveshaft,…
Read full complaint
On BMW there is a consistent problem with the oil filter housing gasket leaking oil which runs down and gets on the V-belt causing slipping that affects power steering. It is common problem for the emergency brake plastic clip to brake and cause the emergency brake cable that runs above the drive shaft to scrape the driveshaft, causing the cable to wear out and cause premature failure of the emergency brake.
NHTSA ODI #11561965
144,000 miles · Sep 13, 2023
EngineFire
The contact owned a 2015 Bmw 328i. The contact stated that while parked, the vehicle had caught on fire. The origin of the fire was unknown. The fire was in the engine area. The contact used a water hose to extinguish the fire. A fire department report was filed. There was no police report filed. No warning light was illuminated…
Read full complaint
The contact owned a 2015 Bmw 328i. The contact stated that while parked, the vehicle had caught on fire. The origin of the fire was unknown. The fire was in the engine area. The contact used a water hose to extinguish the fire. A fire department report was filed. There was no police report filed. No warning light was illuminated. The vehicle had not been diagnosed or repaired by an independent mechanic or dealer. The manufacturer was made aware of the failure. The failure mileage was approximately 144,000.
NHTSA ODI #11544345
Mileage unknown · Sep 6, 2023
EngineFuel/propulsion System
Drivetrain malfunction warning comes on when the car runs for a few hours in the heat or when randomly driving. Sometimes the warning will clear itself after waiting a few minutes, but it might come back after a few minutes driving or not. In other instances, the drivetrain will not clear itself and will take more than a few hou…
Read full complaint
Drivetrain malfunction warning comes on when the car runs for a few hours in the heat or when randomly driving. Sometimes the warning will clear itself after waiting a few minutes, but it might come back after a few minutes driving or not. In other instances, the drivetrain will not clear itself and will take more than a few hours. Took it to the repair shop 3 times and they indicated it could be the fuel pump modular or spark plugs or it could just be that the heat is messing up the software system. The mechanic has mentioned that drivetrain malfunctions have been occurring more regularly with BMWs. The issue is that this drivetrain can malfunction at any random time. Driving on a highway, street, or just starting up the car after letting it sit for a few minutes or days. It's a safety hazard because it can happen at any time unexpectedly. When it does, the car goes into neutral and this is dangerous if driving on the highway at higher speeds and needing to pull over into right hand lane. I've not yet taken it to a dealer to look at, just a certified BMW repair shop. There have been no warning issues and the car clears whenever it is taken to the repair shop.
NHTSA ODI #11542816
Mileage unknown · Aug 22, 2023
EnginePower TrainSuspension
After consulting many others that own or previously owned 328i bmw from around the same years (2015-2017); a common issue was found and assumed to be the timing belt. when i press on the accelerator moderately/ as per usual, my RPMs and speedometer hesitate for a solid second then it will catch up and start shaking. i suspect it…
Read full complaint
After consulting many others that own or previously owned 328i bmw from around the same years (2015-2017); a common issue was found and assumed to be the timing belt. when i press on the accelerator moderately/ as per usual, my RPMs and speedometer hesitate for a solid second then it will catch up and start shaking. i suspect its the timing belt.
NHTSA ODI #11540161
Mileage unknown · Sep 5, 2022
Engine
BMW 328I check engine sensor light on code p0281 to replace coolant thermostat. Part has been replaced and code continually appears something’s as ABS CHASIS malfunction sensor or check engine. Code also reads thermostat stuck open.
NHTSA ODI #11482888
Mileage unknown · Sep 3, 2022
EnginePower Train
Driving to work and the engine oil pressure warning came up and the car began to decelerate and once completely stopped the power train malfunction warning popped up and I couldn’t restart the engine. Towed to BMW of Toledo and was Told the timing chain broke and destroyed the engine.
NHTSA ODI #11482766
82,000 miles · Aug 3, 2022
Engine
The contact owns a 2015 BMW 328i. The contact stated while driving approximately 35 MPH, the vehicle lost motive power and independently restarted in LIMP mode. The contact stated no warning light was illuminated. The contact stated that the failure recurred and various speeds. The contact had not taken the vehicle to a local de…
Read full complaint
The contact owns a 2015 BMW 328i. The contact stated while driving approximately 35 MPH, the vehicle lost motive power and independently restarted in LIMP mode. The contact stated no warning light was illuminated. The contact stated that the failure recurred and various speeds. The contact had not taken the vehicle to a local dealer or independent mechanic to be diagnosed or repaired. The manufacturer had not been informed of the failure. The failure mileage was approximately 82,000.
NHTSA ODI #11477356
71,000 miles · Feb 6, 2021
Engine
VALVE COVER SEAL FAILURE. SMOKE IN COMPARTMENT AND IN ENGINE BLOCK
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence & remedy
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
Engine And Engine Cooling:cooling System:pump
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2015 6 Series Gran Coupe, 2014 5 Series Gran Turismo, 2014 5 Series Sedan, 2015 6 Series Convertible, 2015 6 Series Coupe, 2014 X5, 2013-2014 X3, 2014-2015 3 Series Sedan, 2014 4 Series Coupe, 2014 4 Series Convertible, 2014 3 Series Gran Turismo, and 2015 4 Series Gran Coupe vehicles. Please see the recall report for the complete list of models. The driver's air bag inflator may explode during deployment, due to a manufacturing defect.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, increasing the risk of injury or death.
Remedy: The driver's front air bag will be replaced, free of charge. Owner notification letters were mailed September 6, 2024. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2014-2015 2 Series Coupe (228i, 228i xDrive, M235i), 3 Series Sedan (320i, 320i xDrive, 328i, 328i xDrive, 335i, 335i xDrive, M3, 328d, 328d xDrive), 4 Series Coupe (428i, 428i xDrive, 435i, 435i xDrive, M4), and 2015 4 Series Gran Coupe (428i, 428i xDrive, 435i, 435i xDrive) vehicles. The head air bag inflator may fail at the weld joint, which can cause gas to leak from the inflator or result in an inflator rupture.
Consequence & remedy
Consequence: An inflator that ruptures may cause sharp metal fragments to enter or exit the vehicle, increasing the risk of injury. Additionally, an inflator that leaks gas may only partially inflate during a crash, increasing the risk of injury.
Remedy: Dealers will replace the head air bags, free of charge. Owner notification letters were mailed November 4, 2024. Owners may contact BMW customer service at 1-800-525-7417.
BMW North America, LLC (BMW) is recalling certain model year 2012-2015 320i, 320xi, 328i, 328xi, 335i, 335xi, and ActiveHybrid3 vehicles manufactured October 20, 2011, to June 22, 2015, 2014-2015 328xi Sports Wagon vehicles manufactured March 21, 2013, to March 17, 2015, 2014-2015 328d, 328xd vehicles manufactured June 28, 2013, to April 21, 2015, and 2014-2015 328xd Sports Wagon vehicles manufactured July 5, 2013, to April 21, 2015. The affected vehicles may have been programmed with new software that inadvertently makes the front side marker lights inoperative in conjunction with the parking lights or the headlights. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment."
Consequence & remedy
Consequence: If the side marker lights do not illuminate, the vehicle may be less visible at night, increasing the risk of a crash.
Remedy: BMW will notify owners, and dealers will upload revised software to correct the issue, free of charge. The recall began on October 7, 2015. Owners may contact BMW customer service at 1-800-525-7417 or by email at CustomerRelations@bmwusa.com.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1
EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
2015 BMW 328I Problems, Complaints & Recalls | Skip That Year
Illustration