Common problem with this year and model is the low beam projector headlight assembly dims. This is a huge hazard and makes it impossible to see at night with low beam lights. I cannot see more than 30 feet in front of the vehicle at night making the reaction time to any potential threat non-existent at freeway speed and severe…
Read full complaint
Common problem with this year and model is the low beam projector headlight assembly dims. This is a huge hazard and makes it impossible to see at night with low beam lights. I cannot see more than 30 feet in front of the vehicle at night making the reaction time to any potential threat non-existent at freeway speed and severely reduced in neighborhoods. All options investigated are to replace assembly, not lightbulb. This is a manufacturer fault and cost should be bourn by the manufacturer. Same problem with the RLX and Acura voluntarily recalled those headlights for replacement. They should be required to do the same for these.
NHTSA ODI #11711530
Mileage unknown · Dec 9, 2024
Electrical System
Headlights Due to the lack of brightness and deterioration over time, the driver is left with a lack of visibility. UNKNOWN if reproduced. No inspections. No warnings or messages.
NHTSA ODI #11629602
Mileage unknown · Jul 9, 2024
Electrical System
Drove vehicle home during daylight. At nite the low-beam lights are useless high-beam needed to be able to see. Carfax was unaware of a "safety recall" for this problem. I found numerous complaints about this on the web. There needs to be a "recall" to get this corrected. Should be addressed by mfg and not consumer.
NHTSA ODI #11600509
Mileage unknown · Jun 18, 2024
Electrical System
An electrical keyless part in the vehicle drains the battery causing it to stall wherever or whenever you are on the road. It has been confirmed by the dealer(Courtesy Acura) that the vehicle needs a new part that they are unable to manufacture in a timely manner. It has been almost a year since the incident, and Honda is sti…
Read full complaint
An electrical keyless part in the vehicle drains the battery causing it to stall wherever or whenever you are on the road. It has been confirmed by the dealer(Courtesy Acura) that the vehicle needs a new part that they are unable to manufacture in a timely manner. It has been almost a year since the incident, and Honda is still not supporting a product that was faulty the day the car rolled off the assembly line. I was told by a representative of Honda that my car, 2015 Acura RDX, is the only vehicle with that VIN number to have this problem, and I know that not to be true.
NHTSA ODI #11595080
Mileage unknown · Dec 11, 2023
Electrical System
The Keyless Entry TPMS controller in the car, part #38320-TX4-Ao1 malfunctions, and the care does not turn itself off. The engine normally stops, but electrical systems continue operating and the car will drain its battery with a few hours. This is not an isolated occurance, while dealership personnel have not given firm #s,…
Read full complaint
The Keyless Entry TPMS controller in the car, part #38320-TX4-Ao1 malfunctions, and the care does not turn itself off. The engine normally stops, but electrical systems continue operating and the car will drain its battery with a few hours. This is not an isolated occurance, while dealership personnel have not given firm #s, I beleive this may be effecting as high as 20% of the vehicles with this part. We have had a replacement part on back order since August 30th of 2023, today the dealship told me we are elevated to Urgent Backorder with not estimated fulfillment. On service tech told me the issue is that Acura suspended manufacture of the part as they try to solve this issue.
NHTSA ODI #11559570
Mileage unknown · Jul 31, 2022
Electrical SystemExterior LightingPower Train
I've had the vehicle since around 44 k , Purchase and shortly months later technology lighting a battery issues, someone started hacking me saying they were a car warranty services , harassment in cybersecurity daily I've had over 6-8 electrical light replacements, 2-3 battery replacements, 3 alternator replacements, hacking is …
Read full complaint
I've had the vehicle since around 44 k , Purchase and shortly months later technology lighting a battery issues, someone started hacking me saying they were a car warranty services , harassment in cybersecurity daily I've had over 6-8 electrical light replacements, 2-3 battery replacements, 3 alternator replacements, hacking is daily asking me to pay brides of 1000.00 which I have never participated in, someone talks the entire time stating they are getting my information, hacked my plates, tries to control the vehicle and using cyber security. Department of justice suggested to go to acura dealer for cyber ecu reset , inquired car about the car someone hacked the car saying they are trying to steal social security benefits, and preventing employment and want to impact finances. Car was hacked and shut down had triple AAA come out to look at the vehicle which was not working was informed it was the communicator of the body throttle but would need to have dealer process and program because of computer communication to release and preform gas pedal and power train. Picture video proving the noise and item car unable to lock some one broke into the vehicle and impacted the timing belt and etc. I have documents to support but want to be cautious of hackers and would be willing to share directly for safety pre-cautions
NHTSA ODI #11476731
210 miles · Sep 14, 2020
Electrical SystemElectronic Stability Control (esc)Steering
AFTER DRIVING ON THE INTERSTATE AND THEN SLOWING DOWN, A CHECK VSA SYSTEM, CHECK HILL START ASSIST SYSTEM, AND CHECK POWER STEERING LIGHT COMES ON THE DASH. SOMETIMES AFTER A RESTART THE LIGHT DOESN'T COME ON. SOMETIMES IT TAKES MULTIPLE DRIVES AND RESTARTS TO CLEAR THE LIGHT.
NHTSA ODI #11354937
Mileage unknown · Sep 30, 2018
Electrical System
SOMETHING IS DRAINING THE BATTERY, KEEP HAVING TO JUMPSTART IT AND STALLS SOMETIMES WHEN DRIVING. BATTERY PASS AS GOOD. I DID RESEARCH ON IT AND A LOT OF COMPLAINTS ABOUT IT.
Honda (American Honda Motor Co.) is recalling certain 2013 Acura ILX, 2015 RDX, 2005-2010 and 2012 RL, 2009-2014 TL, 2010 and 2012 ZDX, 2007-2011 CR-V, 2011-2013 and 2015 CR-Z, 2009-2013 Fit, 2013 Fit EV, 2010-2011 and 2013 Insight and 2007-2014 Ridgeline vehicles. These vehicles are equipped with driver frontal air bag inflators assembled as a recall remedy part or replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Honda will notify owners, and dealers will replace the driver frontal air bag inflator, free of charge. The recall began August 12, 2019. Owners may contact Honda customer service at 1-888-234-2138. Honda's numbers for this recall are S5B and W59.
Honda (American Honda Motor Co.) is recalling specific 2003 Acura 3.2CL, 2013-2016 ILX, 2013-2014 ILX Hybrid, 2003-2006 MDX, 2007-2016 RDX, 2002-2003 3.2TL, 2004-2006, and 2009-2014 TL, 2010-2013 ZDX and 2001-2007 and 2009 Honda Accord, 2001-2005 Civic, 2003-2005 Civic Hybrid, 2001-2005 Civic GX NGV, 2002-2007 and 2010-2011 CR-V, 2003-2011 Element, 2007 Fit, 2002-2004 Odyssey, 2003-2008 Pilot, and 2006-2014 Ridgeline vehicles. The affected vehicles received a replacement driver air bag inflator as part of a previous Takata inflator recall remedy or a replacement driver air bag module containing the same inflator type as a service part. Due to a manufacturing error, in the event of a crash necessitating deployment of the driver frontal air bag, these inflators may explode.
Consequence & remedy
Consequence: An explosion of an inflator within the driver frontal air bag module may result in sharp metal fragments striking the driver, front seat passenger or other occupants resulting in serious injury or death.
Remedy: Honda will notify owners, and dealers will replace the driver's air bag inflator with an alternate inflator, free of charge. The recall began April 10, 2019. Honda owners may contact customer service at 1-888-234-2138. Honda's number for this recall is O41. Acura owners may contact customer service at 1-888-234-2138. Acura's number for this recall is U40.
Honda (American Honda Motor Co.) is recalling certain model year 2007-2011 Honda CR-V, 2011-2015 CR-Z, 2010-2014 FCX, and Insight, 2009-2013 Fit, 2013-2014 Fit EV, 2007-2014 Ridgeline, 2013-2016 Acura ILX, 2013-2014 Acura ILX Hybrid, 2007-2016 RDX, 2005-2012 Acura RL, 2009-2014 Acura TL, and 2010-2013 Acura ZDX vehicles. The affected vehicles are equipped with a dual-stage driver frontal air bag that may be susceptible to moisture intrusion which, over time, could cause the inflator to rupture.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Honda will notify owners, and dealers will replace the inflator, free of charge. The recall began March 2017. Owners may contact Honda customer service at 1-888-234-2138. Honda's numbers for this recall are JY0, JY1, and JY2.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1
EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
2015 Acura Rdx Problems, Complaints & Recalls | Skip That Year
Illustration